Page 1
PROFLEX®6036
Features
ExoCrylic
•
Drop-in or three-wall alcove
•
Six individually adjustable ProFlex
•
jets
Pump with air switch and grounding-type plug-in cord
•
In-line heater
•
Molded lumbar support and armrests for comfort
•
Optional K-9696 whirlpool trim kit in additional
•
finishes
Optional K-1284 removable apron
•
60″ (1524 mm) x 36″ (914 mm) x 18-1/8″ (460 mm)
•
TM
hydro-massage
®
Codes/Standards Applicable
Specified model meets or exceeds the following:
ASME A112.19.7/CSA B45.10
•
CSA B45.5/IAPMO Z124
•
UL 1795
•
WHIRLPOOL BATH WITH HEATER
K-1139-H
ALSO K-1139-LH, K-1139-RH
Colors/Finishes
0: White
•
CP: Polished Chrome
•
PB: Vibrant®Polished Brass
•
Other: Refer to Price Book for additional colors/finishes
•
Specified Model
Model Description Colors/Finishes
K-1139-H Whirlpool bath with heater – drop-in (shown) ❑ 0 ❑ Other_____
K-1139-LH Whirlpool bath with heater – tile flange, left drain ❑ 0 ❑ Other_____
K-1139-RH Whirlpool bath with heater – tile flange, right drain ❑ 0 ❑ Other_____
Recommended Accessories
K-11677 Swiftflo
Optional Accessories
K-1284 Removable apron ❑ 0 ❑ Other_____
K-9696 Jet trim kit (metal finishes) ❑ CP ❑ PB ❑ Other_____
TM adjustable trip lever bath drain ❑ CP ❑ PB
Product Specification
The ExoCrylic whirlpool bath shall be 60″ (1524 mm) in length, 36″ (914 mm) in width, and 18-1/8″ (460 mm) in height. Whirlpool
shall be for drop-in [K-1139-H] or three-wall alcove [K-1139-LH, K-1139-RH] installation. Whirlpool shall have six individually
adjustable ProFlex hydro-massage jets, pump with air switch and grounding-type plug-in cord, and in-line heater. Whirlpool shall
have molded lumbar support and armrests for comfort. Whirlpool shall feature optional K-1284 removable apron, and K-9696
whirlpool trim kit in additional finishes. Whirlpool bath shall be Kohler Model K-1139-____-____.
Page 1 of 2
1013750-4-
USA/Canada: 1-800-4KOHLER
F
(1-800-456-4537)
www.kohler.com
Page 2
PROFLEX®6036
Technical Information
Fixture*:
Bathing well:
Basin area, bottom 46″ (1168 mm) x 15″ (381 mm)
Basin area, top 55″ (1397 mm) x 25″ (635 mm)
Weight 60 lbs (27.2 kg)
To overflow:
Water depth 14″ (356 mm)
Capacity 57 gal (215.8 L)
* Approximate measurements for comparison only.
Drop-in cutout 58-1/2″ (1486 mm) x 34-1/2″ (876 mm)
Pump: V Hz A
1-speed 120 60 7.5
Heater: kW V Hz A
1.5 120 60 12.5
Required Electrical Service
Two dedicated circuits required, each protected with
Class A Ground-Fault Circuit-Interrupter (GFCI):
Pump/control 120 V, 15 A, 60 Hz
Heater 120 V, 15 A, 60 Hz
Locate the outlets behind the whirlpool and within 24″
(610 mm) of the pump.
Installation Notes
Install this product according to the installation guide.
Floor support under whirlpool must provide for a minimum of
37 lbs/square foot (183 kg/square meter) loading.
The apron must be installed before the finished floor and wall
materials are installed.
18"
(457 mm)
2-1/2"
(64 mm)
3"
(76 mm)
8" (203 mm)
60" (1524 mm)
2-7/8"
3/8" (10 mm)
(73 mm)
Lumbar
Angle 29˚
18-1/8"
(460 mm)
No change in measurements if connected
with drain illustrated. (K-11677)
1-1/4"
(32 mm)
Pump/Control Access
(If Apron Is Not Used)
20" (508 mm) W x
15" (381 mm) H
Tile Flange
Detail
36" (914 mm)
1-1/2"
(38 mm)
16-5/8"
(422 mm)
Drop-in Rim
1-1/2" Bath Drain
Detail
Product Diagram
PROFLEX®6036 WHIRLPOOL BATH WITH HEATER
Page2of2
1013750-4-
F
Loading...