Page 1
ARCHERTM
Features
Acrylic
•
8 color-matched Kohler hydro-massage jets
•
Integral apron with removable access panel
•
Pump with air switch and grounding-type plug-in cord
•
Integral tile flange
•
In-line heater
•
Left or right drain
•
Slotted overflow for maximum bathing depth
•
Integral lumbar support
•
Armrests
•
60″ (1524 mm) x 32″ (813 mm) x 19″ (483 mm)
•
Codes/Standards Applicable
Specified model meets or exceeds the following:
ADA
•
ICC/ANSI A117.1
•
ASME A112.19.7
•
CSA B45.5/IAPMO Z124
•
ASTM E162
•
ASTM E662
•
Specified Model
5’ BATH WHIRLPOOL WITH HEATER
K-1122-HL
ALSO K-1122-HR
Colors/Finishes
0: White
•
Other: Refer to Price Book for additional colors/finishes
•
Accessories
CP: Polished Chrome
•
Other: Refer to Price Book for additional colors/finishes
•
Model Description Colors/Finishes
K-1122-HL Bath whirlpool with integral apron and heater, left drain ❑ 0 ❑ Other_____
K-1122-HR Bath whirlpool with integral apron and heater, right drain ❑ 0 ❑ Other_____
Required Accessories
K-7271 Clearflo slotted overflow brass bath drain OR ❑ CP ❑ Other_____
K-7272 Clearflo slotted overflow bath drain – PVC pipe ❑ CP ❑ Other_____
Product Specification
The acrylic bath whirlpool shall be 60″ (1524 mm) in length, 32″ (813 mm) in width, and 19″ (483 mm) in height. Bath whirlpool
shall have 8 color-matched jets and pump with air switch and grounding-type plug-in cord. Bath whirlpool shall have an in-line
heater. Bath whirlpool shall have an integral apron with removable access panel and integral tile flange. Bath whirlpool shall
have left or right drain. Bath whirlpool shall have slotted overflow for maximum bathing depth, low threshold height, and integral
lumbar support. Bath shall have armrests. Bath whirlpool shall be Kohler Model K-1122-______-______.
Page 1 of 2
1071359-4-
E
USA/Canada: 1-800-4KOHLER
(1-800-456-4537)
www.kohler.com
Page 2
ARCHERTM
Technical Information
Fixture*:
Bathing well:
Basin area, bottom 45-1/8″ (1146 mm) x 19-11/16″
(500 mm)
Basin area, top 52-3/4″ (1340 mm) x 25-5/16″
(643 mm)
Weight 140 lbs (63.5 kg)
To overflow:
Water depth 15″ (381 mm)
Capacity 58 gal (219.5 L)
* Approximate measurements for comparison only.
Pump: V Hz A
1-speed 120 60 7
Heater: kW V Hz A
1.5 120 60 12.5
Required Electrical Service
(2 required)
Two dedicated circuits required, each protected with
Class A Ground-Fault Circuit-Interrupter (GFCI):
Pump/control 120 V, 15 A, 60 Hz
Heater 120 V, 15 A, 60 Hz
Installation Notes
Install this product according to the installation guide.
Floor support under this product must provide for a minimum
of 49 lbs/square foot (240 kg/square meter) loading.
The hot water supply should be 70% of the capacity of the
bath or greater. Installations will vary.
Will comply with ADA when installed per Section 607
Bathtubs of the Act.
No change in measurements if connected
with drain illustrated. (K-7272)
16"
(406 mm)
1-1/4"
(32 mm)
2-1/2"
(64 mm)
1-1/2"
Bath Drain
11-1/4"
(286 mm)
60" (1524 mm)
4-1/8"
(105 mm)
1-1/4"
(32 mm)
1/2" (13 mm) R.
Integral Flange
Detail
32" (813 mm)
19"
(483 mm)
3/4" (19 mm)
Product Diagram
ARCHERTM 5’ BATH WHIRLPOOL WITH HEATER
Page2of2
1071359-4-
E
Loading...