Page 1
MARIPOSA
®
Features
Acrylic
•
Integral apron with removable access panel
•
5 individually adjustable ProFlex
•
Pump with air switch and grounding-type plug-in cord
•
In-line heater
•
Optional K-9695 metal finish 5 jet trim kit
•
60″ (1524 mm) x 36″ (914 mm) x 20″ (508 mm)
•
hydro-massage jets
®
Codes/Standards Applicable
Specified model meets or exceeds the following:
ASME A112.19.7
•
UL 1795
•
CSA B45.5/IAPMO Z124
•
Specified Model
BATH WHIRLPOOL WITH INTEGRAL
APRON AND HEATER
K-1239-HL
ALSO K-1239-HR
Colors/Finishes
0: White
•
Other: Refer to Price Book for additional colors/finishes
•
Accessories
CP: Polished Chrome
•
PB: Vibrant®Polished Brass
•
Other: Refer to Price Book for additional colors/finishes
•
Model Description Colors/Finishes
K-1239-HL Bath whirlpool with integral apron and heater – left drain ❑ 0 ❑ Other_____
K-1239-HR Bath whirlpool with integral apron and heater – right drain ❑ 0 ❑ Other_____
Recommended Accessories
K-7161-AF Adjustable pop-up drain with tailpiece ❑ CP ❑ PB ❑ Other_____
Optional Accessories
K-1278 Removable apron ❑ 0 ❑ Other_____
K-9695 Metal finish 5 jet trim kit ❑ CP ❑ PB ❑ Other_____
Product Specification
The acrylic bath whirlpool shall be 60″ (1524 mm) in length, 36″ (914 mm) in width, and 20″ (508 mm) in height. Bath whirlpool
shall have an integral apron with removable access panel. Bath whirlpool shall have 5 individually adjustable Proflex
hydro-massage jets, a pump with air switch and grounding-type plug-in cord, and an in-line heater. Bath whirlpool shall be
available with an optional K-9695 metal finish 5 jet trim kit. Bath whirlpool shall be Kohler Model K-1239-____-____.
Page 1 of 2
1014712-4-
D
USA/Canada: 1-800-4KOHLER
(1-800-456-4537)
www.kohler.com
®
Page 2
MARIPOSA
®
Technical Information
Required Electrical Service
Fixture*:
Bathing well:
Basin area, bottom 46″ (1168 mm) x 24″ (610 mm)
Basin area, top 54″ (1372 mm) x 27″ (686 mm)
Weight 110 lbs (49.9 kg)
To overflow:
Water depth 14″ (356 mm)
Capacity 63 gal (238.5 L)
* Approximate measurements for comparison only.
Pump: V Hz A
1-speed 120 60 7.5
Heater: Kw V Hz A
1.5 120 60 12.5
Two dedicated circuits required, each protected with
Class A Ground-Fault Circuit-Interrupter (GFCI):
Pump/control 120 V, 15 A, 60 Hz
Heater 120 V, 15 A, 60 Hz
Locate the outlets behind the whirlpool and within 24″
(610 mm) of the pump and heater.
Installation Notes
Install this product according to the installation guide.
Floor support under whirlpool must provide for a minimum of
44 lbs/square foot (215 kg/square meter) loading.
If installing a rim-mount faucet, make sure there is no
interference with the drain overflow and circulating system
before drilling any holes. If installing a spout on the faucet
deck, consult local and national codes for minimum air gap
requirements.
No change in measurements if connected with drain
illustrated. (K-7161-AF or K-7161M-AF)
Recommended Faucet Area
18"
(457 mm)
1-11/16"
(43 mm)
8-11/16"
(221 mm)
3-1/2"
60" (1524 mm)
(89 mm)
20"
(508 mm)
1" (25 mm)
3"
2-7/8"
(73 mm)
(76 mm)
Product Diagram
MARIPOSA®BATH WHIRLPOOL WITH INTEGRAL APRON AND HEATER
Page2of2
1014712-4-
D
1-1/4"
(32 mm)
1/2" (13 mm)
R. Max
Integral
Flange Detail
36" (914 mm)
1-1/2" OD
Loading...