Page 1
MARIPOSA
®
Features
Acrylic
•
Drop-in or three-wall alcove
•
5 individually adjustable ProFlex
•
Pump with air switch and grounding-type plug-in cord
•
In-line heater
•
UL listed
•
Optional K-9695 metal finish 5 jet trim kit
•
Optional K-1278 removable apron
•
60″ (1524 mm) x 36″ (914 mm) x 20″ (508 mm)
•
hydro-massage jets
®
Codes/Standards Applicable
Specified model meets or exceeds the following:
ASME A112.19.7
•
UL 1795
•
CSA B45.5/IAPMO Z124
•
Specified Model
BATH WHIRLPOOL WITH HEATER
K-1239-H
ALSO K-1239-LH, K-1239-RH
Colors/Finishes
0: White
•
Other: Refer to Price Book for additional colors/finishes
•
Accessories
CP: Polished Chrome
•
PB: Vibrant®Polished Brass
•
Other: Refer to Price Book for additional colors/finishes
•
Model Description Colors/Finishes
K-1239-H Bath whirlpool with heater – drop-in ❑ 0 ❑ Other_____
K-1239-LH Bath whirlpool with heater – three-wall alcove, left drain (shown) ❑ 0 ❑ Other_____
K-1239-RH Bath whirlpool with heater – three-wall alcove, right drain ❑ 0 ❑ Other_____
Recommended Accessories
K-7161-AF Adjustable pop-up drain with tailpiece ❑ CP ❑ PB ❑ Other_____
Optional Accessories
K-1278 Removable apron ❑ 0 ❑ Other_____
K-9695 Metal finish 5 jet trim kit ❑ CP ❑ PB ❑ Other_____
Product Specification
The acrylic bath whirlpool shall be 60″ (1524 mm) in length, 36″ (914 mm) in width, and 20″ (508 mm) in height. Product shall
be for drop-in installation [K-1239-H] or three-wall alcove installation [K-1239-LH, K-1239-RH]. Product shall include 5
individually adjustable ProFlex hydro-massage jets, a pump with air switch and grounding-type plug-in cord, and an in-line
heater. Product shall be UL listed. Product shall be available with an optional K-1278 removable apron and an optional K-9695
metal finish 5 jet trim kit. Bath whirlpool shall be Kohler Model K-1239-______-_______.
Page 1 of 2
1014711-4-
D
USA/Canada: 1-800-4KOHLER
(1-800-456-4537)
www.kohler.com
Page 2
MARIPOSA
®
Technical Information
Required Electrical Service
Fixture*:
Basin area:
Bathing area, bottom 46″ (1168 mm) x 24″ (610 mm)
Bathing area, top 54″ (1372 mm) x 27″ (686 mm)
Weight 110 lbs (49.9 kg)
To overflow:
Water depth 14″ (356 mm)
Capacity 63 gal (238.5 L)
* Approximate measurements for comparison only.
Drop-in cutout: 58″ (1473 mm) x 34″ (864 mm)
Pump V Hz A
1-speed 120 60 7.5
Heater: Kw V Hz Hz
1.5 120 60 12.5
18"
(457 mm)
Two dedicated circuits required, each protected with
Class A Ground-Fault Circuit-Interrupter (GFCI):
Pump/control 120 V, 15 A, 60 Hz
Heater 120 V, 15 A, 60 Hz
Locate the outlets behind the whirlpool and within 24″
(610 mm) of the pump and heater.
Installation Notes
Install this product according to the installation guide.
Floor support under whirlpool must provide for a minimum of
44 lbs/square foot (215 kg/square meter) loading.
If installing a rim-mount faucet, make sure there is no
interference with the drain overflow before drilling any holes.
Consult local and national codes for minimum air gap
requirements if installing a spout on the faucet deck.
The apron must be installed before the finished floor and wall
materials are installed.
No change in measurements if connected with
drain illustrated. (K-7161-AF or K-7161M-AF)
Recommended Faucet Area
1-11/16"
(43 mm)
8-11/16"
(221 mm)
60" (1524 mm)
3-1/2"
(89 mm)
1" (25 mm)
3"
2-7/8"
(73 mm)
(76 mm)
Product Diagram
MARIPOSA®BATH WHIRLPOOL WITH HEATER
Page2of2
1014711-4-
D
Pump/Control Access
(if apron is not used)
20" (508 mm) W x
15" (381 mm) H
20"
(508 mm)
18-1/2"
(470 mm)
1-1/2" OD
36" (914 mm)
1-1/4"
(32 mm)
1/2" (13 mm)
R. Max
Integral
Flange Detail
1-1/2"
(38 mm)
Drop-in Rim
Detail
Loading...