Page 1
MARIPOSA
®
Features
Acrylic
•
5 individually adjustable ProFlex
•
Pump with air switch and grounding-type plug-in cord
•
Integral apron with removable access panel
•
In-line heater
•
Left or right drain
•
Textured bottom surface
•
Optional K-1234 removable apron
•
Optional K-9695 metal finish 5 jet trim kit
•
Integral tile flange on three sides for alcove
•
installation
66″ (1676 mm) x 35-7/8″ (911 mm) x 20″ (508 mm)
•
hydro-massage jets
®
Codes/Standards Applicable
Specified model meets or exceeds the following:
ANSI Z124.1.2
•
ASME A112.19.7
•
UL 1795
•
ASTM E162
•
ASTM E662
•
Specified Model
BATH WHIRLPOOL WITH INTEGRAL
APRON AND HEATER
K-1224-HL
ALSO K-1224-HR
Colors/Finishes
0: White
•
Other: Refer to Price Book for additional colors/finishes
•
Accessories
0: White
•
CP: Polished Chrome
•
PB: Polished Brass
•
Other: Refer to Price Book for additional colors/finishes
•
Model Description Colors/Finishes
K-1224-HL Bath whirlpool with integral apron and heater – left drain (shown) ❑ 0 ❑ Other_____
K-1224-HR Bath whirlpool with integral apron and heater – right drain ❑ 0 ❑ Other_____
Recommended Accessories
K-7166-AF Adjustable pop-up bath drain ❑ CP ❑ PB ❑ Other_____
K-7213 Clearflo bath cable drain with PVC tubing ❑ CP ❑ Other_____
K-7214 Clearflo bath cable drain without PVC tubing ❑ CP ❑ Other_____
Product Specification
The acrylic bath whirlpool shall be 66″ (1676 mm) in length, 35-7/8″ (911 mm) in width, and 20″ (508 mm) in height. Product
shall have integral apron with removable access panel and integral tile flange on three sides for alcove installation. Product shall
have a textured bottom surface and a drain at left or right. Product shall have 5 individually adjustable Proflex hydro-massage
jets, a pump with air switch and grounding-type plug-in cord, and an in-line heater. Product shall have an optional K-1234
removable apron and an optional K-9695 metal finish 5 jet trim kit. Bath whirlpool shall be Kohler Model K-1224-____-____.
Page 1 of 2
1038378-4-
D
USA/Canada: 1-800-4KOHLER
(1-800-456-4537)
www.kohler.com
Page 2
MARIPOSA
Optional Accessories
K-1234 Removable apron ❑ 0 ❑ Other_____
K-9695 Metal finish 5 jet trim kit ❑ CP ❑ PB ❑ Other_____
®
Technical Information
Fixture*:
Basin area:
Bathing well, bottom 48″ (1219 mm) x 24″ (610 mm)
Bathing well, top 59″ (1499 mm) x 30″ (762 mm)
Weight 110 lbs (49.9 kg)
To overflow:
Water depth 14″ (356 mm)
Capacity 67 gal (254 L)
* Approximate measurements for comparison only.
Pump V Hz A
1-speed 120 60 12.5
Heater: kW V Hz A
1.5 120 60 12.5
18"
(457 mm)
Required Electrical Service
Two dedicated circuits are required, each protected with
Class A Ground-Fault Circuit-Interrupter (GFCI).
Pump/control 120 V, 15 A, 60 Hz
Heater 120 V, 15 A, 60 Hz
Locate the outlets behind the whirlpool and within 24″
(610 mm) of the pump and heater.
Installation Notes
Install this product according to the installation guide.
Floor support under the whirlpool must provide for a minimum
of 42 lbs/square foot (205 kg/square meter) loading.
If installing a rim-mount faucet, make sure there is no
interference with the drain overflow before drilling any holes.
Consult local and national codes for minimum air gap
requirements if installing a spout on the faucet deck.
No change in measurements with drain
shown. (K-7161-AF or K-7161M-AF)
Recommended faucet area.
1-11/16"
(43 mm)
8-11/16"
(221 mm)
66" (1676 mm)
3-1/2"
(89 mm)
3"
2-7/8"
(73 mm)
1" (25 mm)
20"
(508 mm)
(76 mm)
Product Diagram
MARIPOSA®BATH WHIRLPOOL WITH INTEGRAL APRON AND HEATER
Page2of2
1038378-4-
D
36" (914 mm)
Ø 1-1/2"
1-1/4"
(32 mm)
1/2" R.
(13 mm) Max
Integral
Flange Detail
Loading...