Page 1
WINDWARD
®
Features
Acrylic
•
Rectangular shape
•
Drop-in
•
Pump with air switch and grounding-type plug-in cord
•
6 individually adjustable ProFlex
•
Molded lumbar supports and armrests
•
In-line heater
•
72″ (1829 mm) x 42″ (1067 mm) x 21″ (533 mm)
•
hydro-massage jets
®
Codes/Standards Applicable
Specified model meets or exceeds the following:
CSA B45.5/IAPMO Z124
•
ASME A112.19.7
•
ASTM E162
•
ASTM E662
•
UL 1795
•
Specified Model
BATH WHIRLPOOL WITH CUSTOM
PUMP AND HEATER
K-1114-HB
Colors/Finishes
0: White
•
Other: Refer to Price Book for additional colors/finishes
•
Accessories
CP: Polished Chrome
•
Other: Refer to Price Book for additional colors/finishes
•
Model Description Colors/Finishes
K-1114-HB Bath whirlpool with custom pump and heater ❑ 0 ❑ Other_____
Recommended Accessories
K-7166 Adjustable pop-up drain – above or through-the-floor installation OR ❑ CP ❑ Other_____
K-11677 Adjustable trip lever drain – through-the-floor installation ❑ CP ❑ Other_____
Optional Accessories
K-9696 Jet trim kit (metal finishes) ❑ CP ❑ Other_____
Product Specification
The rectangular acrylic bath whirlpool shall be 72″ (1829 mm) in length, 42″ (1067 mm) in width, and 21″ (533 mm) in height.
Bath whirlpool shall be drop-in. Bath whirlpool shall have 6 individually adjustable Proflex hydro-massage jets, a pump with air
switch and grounding-type plug-in cord, and an in-line heater. Bath whirlpool shall have molded lumbar supports and armrests.
Bath whirlpool shall be Kohler Model K-1114-HB-_______.
Page 1 of 2
1047220-4-
D
USA/Canada: 1-800-4KOHLER
(1-800-456-4537)
www.kohler.com
Page 2
WINDWARD
®
Technical Information
Fixture*:
Bathing well:
Basin area, bottom 55″ (1397 mm) x 23-1/4″ (591 mm)
Basin area, top 64″ 1626 mm) x 32″ (813 mm)
Weight 132 lbs (60 kg)
To overflow:
Water depth 15″ (381 mm)
Capacity 78.5 gal (297 L)
* Approximate measurements for comparison only.
Drop-in cut-out
dimensions:
Pump: V Hz A
1-speed 120 60 7.5
Heater: kW V Hz A
Minimum access panel pump/control:
20″ (508 mm) W x 15″ (381 mm) H required
70-1/2″ (1791 mm) x 40-1/2″ (1029
mm)
1.5 120 60 12.5
Required Electrical Service
(2 required)
Two dedicated circuits required, both protected with a
Class A Ground-Fault Circuit-Interrupter (GFCI):
Pump/control 120 V, 15 A, 60 Hz
Heater 120 V, 15 A, 60 Hz
Locate the outlets behind the whirlpool and within 24″
(610 mm) of the pump and, if supplied, heater.
Installation Notes
Install this product according to the installation guide.
Floor support under the whirlpool must provide for a minimum
of 39 lbs/square foot (189 kg/square meter) loading.
If installing a rim-mount faucet, make sure there is no
interference with the drain overflow and circulating system
before drilling any holes. Consult local and national codes for
minimum air gap requirements if installing a spout on the
faucet deck.
21"
(533 mm)
3-3/4"
(95 mm)
3-1/2"
(89 mm)
11-1/16"
(281 mm)
3"
(76 mm)
Pump/Control Access
72" (1829 mm)
2-7/8"
3/8" (10 mm)
(73 mm)
No change in measurements if connected with
drain illustrated. (K-11677)
Recommended faucet area
1-1/2"
(38 mm)
Drop-In
Rim Detail
42" (1067 mm)
1-1/2"
(38 mm)
19-1/2"
(495 mm)
1-1/2" OD
Product Diagram
WINDWARD®BATH WHIRLPOOL WITH CUSTOM PUMP AND HEATER
Page2of2
1047220-4-
D
Loading...