MARIPOSA
®
Features
Acrylic
•
Drop-in
•
5 individually adjustable ProFlex
•
Pump with air switch and grounding-type plug-in cord
•
In-line heater
•
Optional K-9695 metal finish 5 jet trim kit
•
Optional K-1234 removable apron
•
66″ (1676 mm) x 35-7/8″ (911 mm) x 20″ (508 mm)
•
hydro-massage jets
®
Codes/Standards Applicable
Specified model meets or exceeds the following:
ASME A112.19.7
•
ANSI Z124.1.2
•
ASTM E162
•
ASTM E662
•
UL 1795
•
CSA B45.5/IAPMO Z124
•
Specified Model
CUSTOM BATH WHIRLPOOL WITH
HEATER
K-1224-HB
Colors/Finishes
0: White
•
Other: Refer to Price Book for additional colors/finishes
•
Accessories
CP: Polished Chrome
•
PB: Vibrant®Polished Brass
•
Other: Refer to Price Book for additional colors/finishes
•
Model Description Colors/Finishes
K-1224-HB Custom bath whirlpool with heater - drop-in ❑ 0 ❑ Other_____
Recommended Accessories
K-7161-AF Adjustable pop-up drain with tailpiece ❑ CP ❑ PB ❑ Other_____
Optional Accessories
K-1234 Removable apron ❑ 0 ❑ Other_____
K-9695 Metal finish 5 jet trim kit ❑ CP ❑ PB ❑ Other_____
Product Specification
The acrylic bath whirlpool shall be 66″ (1676 mm) in length, 35-7/8″ (911 mm) in width, and 20″ (508 mm) in height. Bath
whirlpool shall be for drop-in installation. Bath whirlpool shall have 5 individually adjustable Proflex
pump with air switch and grounding-type plug-in cord, and an in-line heater. Bath whirlpool shall be available with an optional
K-1234 removable apron and an optional K-9695 metal finish 5 jet trim kit. Bath whirlpool shall be Kohler Model
K-1239-HB-____.
Page 1 of 2
1014727-4-
D
USA/Canada: 1-800-4KOHLER
hydro-massage jets, a
®
(1-800-456-4537)
www.kohler.com
MARIPOSA
®
Technical Information
Required Electrical Service
Fixture*:
Bathing well:
Basin area, bottom 48″ (1219 mm) x 24″ (610 mm)
Basin area, top 59″ (1499 mm) x 30″ (762 mm)
Weight 115 lbs (52.2 kg)
To overflow:
Water depth 14″ (356 mm)
Capacity 67 gal (253.6 L)
* Approximate measurements for comparison only.
Drop-in cutout: 64″ (1626 mm) x 34″ (864 mm)
Pump: V Hz A
1-speed 120 60 7.5
Heater: Kw V Hz A
1.5 120 60 12.5
7-1/2" (191 mm) Max
Pump/Control
Access
20" (508 mm) W x
15" (381 mm) H
Two dedicated circuits required, each protected with
Class A Ground-Fault Circuit-Interrupter (GFCI):
Pump/control 120 V, 15 A, 60 Hz
Heater 120 V, 15 A, 60 Hz
Locate the outlets behind the whirlpool and within 24″
(610 mm) of the pump and heater.
Installation Notes
Install this product according to the installation guide.
Floor support under whirlpool must provide for a minimum of
43 lbs/square foot (208 kg/square meter) loading.
If installing a rim-mount faucet, make sure there is no
interference with the drain overflow and circulating system
before drilling any holes. If installing a spout on the faucet
deck, consult local and national codes for minimum air gap
requirements.
The apron must be installed before the finished floor and wall
materials are installed.
Pump must be relocated to custom position at the time of
installation. Provide adequate clearance.
No change in measurements if connected with drain
illustrated. (K-7161-AF or K-7161M-AF)
Recommended Faucet Area
1-1/2"
(38 mm)
18" (457 mm)
1-11/16" (43 mm)
8-11/16" (221 mm)
66" (1676 mm)
3-1/2" (89 mm)
1" (25 mm)
3"
(76 mm)
2-7/8"
(73 mm)
Product Diagram
MARIPOSA®CUSTOM BATH WHIRLPOOL WITH HEATER
Page2of2
1014727-4-
D
20"
(508 mm)
Drop-in Rim
Detail
35-7/8" (911 mm)
18-1/2"
(470 mm)
Ø 1-1/2"
Loading...