Page 1
MEMOIRS
®
Features
Acrylic
•
Variable speed pump with 1.5 kW heater and back-lit
•
user keypad
8 Flexjet
•
Less all trim
•
66″ (1676 mm) x 42″ (1067 mm) x 22″ (559 mm)
•
TM whirlpool jets
Codes/Standards Applicable
Specified model meets or exceeds the following:
ASME A112.19.7
•
ASTM E162
•
ASTM E662
•
UL 1795
•
CSA B45.5/IAPMO Z124
•
Specified Model
5.5’ BATH WHIRLPOOL
K-1170-H2
Colors/Finishes
0: White
•
Other: Refer to Price Book for additional colors/finishes
•
Accessories
CP: Polished Chrome
•
PB: Vibrant®Polished Brass
•
NA: None applicable
•
Other: Refer to Price Book for additional colors/finishes
•
Model Description Colors/Finishes
K-1170-H2 5.5’ bath whirlpool ❑ 0 ❑ Other_____
Required Accessories
K-9698 Jet trim kit ❑ CP ❑ PB ❑ Other_____
Recommended Accessories
K-7161-AF Pop-up bath drain ❑ CP ❑ PB ❑ Other_____
Optional Accessories
K-1491 Pillow ❑ 0 ❑ Other_____
K-1601 Footstop ❑ 0 ❑ Other_____
K-1703 Remote control ❑ NA
Product Specification
The acrylic bath whirlpool shall be 66″ (1676 mm) in length, 42″ (1067 mm) in width, and 22″ (559 mm) in height. Product shall
have 8 Flexjets, a variable-speed pump, a 1.5 kW heater, and back-lit user keypad. Product shall be less all trim. Bath whirlpool
shall be Kohler Model K-1170-H2-______.
Page 1 of 2
1024311-4-
E
USA/Canada: 1-800-4KOHLER
(1-800-456-4537)
www.kohler.com
Page 2
MEMOIRS
®
Technical Information
Required Electrical Service
Fixture*:
Basin area:
Bathing well 42″ (1067 mm) x 27″ (686 mm)
Top area 54″ (1372 mm) x 30″ (762 mm)
Weight 134 lbs (60.8 kg)
To overflow:
Water depth 16″ (406 mm)
Capacity 81 gal (306.6 L)
* Approximate measurements for comparison only.
Drop-in
cut-out
Pump: kW V Hz A
64-1/2″ (1638 mm) x 40-1/2″ (1029 mm)
1.5 240 50/60 11
Dedicated circuit required, protected with Class A
Ground-Fault Circuit-Interrupter (GFCI) or Residual
Current Device (RCD):
Pump/control 220/240 V, 20 A, 50/60 Hz
Installation Notes
Install this product according to the installation guide.
Floor support under whirlpool must provide for a minimum of
44 lbs/square foot (212 kg/square meter) loading.
Hot water supply should be 70% of capacity or greater.
Installations will vary.
If installing a rim-mount faucet, make sure there is no
interference with drain overflow and circulating system before
drilling any holes. Consult local and national codes for
minimum air gap requirements if installing a spout on the
faucet deck.
This whirlpool is designed for drop-in installation only. It is not
suited for use in a three wall alcove with an overhead shower.
No change in measurements if connected with drain
illustrated. (K-7161-AF or K-7161M-AF)
11-3/4"
(298 mm)
33" (838 mm)
66" (1676 mm)
20-1/8"
(511 mm)
Ø 1-1/2"
MEMOIRS®5.5’ BATH WHIRLPOOL
Page2of2
1024311-4-
E
5-1/4" (133 mm)
3" (76 mm)
1-1/16" (27 mm)
Product Diagram
22"
(559 mm)
Pump/Control Access
34" (864 mm) W x
15" (381 mm) H
42" (1067 mm)
3"
(76 mm)
2-7/8"
(73 mm)
Loading...