PROFLEX®7236
Features
ExoCrylic
•
Drop-in installation
•
Pump with air switch and grounding-type plug-in cord
•
Six individually adjustable ProFlex
•
jets
In-line heater
•
Left or right drain
•
Molded lumbar support and armrests for comfort
•
Optional K-1283 removable apron
•
Optional K-9696 whirlpool trim kit in additional
•
finishes
Tile flange on three sides for alcove installation
•
[K-1157-LH/-RH]
72″ (1829 mm) x 36″ (914 mm) x 20-1/8″ (511 mm)
•
TM
hydro-massage
®
Codes/Standards Applicable
Specified model meets or exceeds the following:
ASME A112.19.7/CSA B45.10
•
CSA B45.5/IAPMO Z124
•
UL 1795
•
Specified Model
WHIRLPOOL BATH WITH HEATER
K-1157-H
ALSO K-1157-LH, K-1157-RH
Colors/Finishes
0: White
•
Other: Refer to Price Book for additional colors/finishes
•
Accessories
0: White
•
CP: Polished Chrome
•
PB: Vibrant®Polished Brass
•
Other: Refer to Price Book for additional colors/finishes
•
Model Description Colors/Finishes
K-1157-H Whirlpool bath with heater – drop-in (shown) ❑ 0 ❑ Other_____
K-1157-LH Whirlpool bath with heater – left drain, tile flange ❑ 0 ❑ Other_____
K-1157-RH Whirlpool bath with heater – right drain, tile flange ❑ 0 ❑ Other_____
Recommended Accessories
K-11677 Adjustable trip lever bath drain ❑ CP ❑ PB
Optional Accessories
K-1283 Removable apron ❑ 0 ❑ Other_____
Product Specification
The ExoCrylic whirlpool bath shall be 72″ (1829 mm) in length, 36″ (914 mm) in width, and 20-1/8″ (511 mm) in height. Whirlpool
shall be drop-in [K-1157-H] or tile flange on three sides for alcove installation with a left or right drain [K-1157-LH/-RH]. Whirlpool
shall have six individually adjustable ProFlex hydro-massage jets, pump with air switch and grounding-type plug-in cord, and
in-line heater. Whirlpool shall have molded lumbar support and armrests for comfort. Whirlpool shall feature optional K-1283
removable apron and K-9696 whirlpool trim kit in additional finishes. Whirlpool bath shall be Kohler Model
K-1157-______-______.
Page 1 of 2
1012988-4-
F
USA/Canada: 1-800-4KOHLER
(1-800-456-4537)
www.kohler.com
PROFLEX®7236
Optional Accessories
K-9696 Jet trim kit (metal finishes) ❑ CP ❑ PB ❑ Other_____
Technical Information
Fixture*:
Bathing well:
Basin area, bottom 55″ (1397 mm) x 21″ (533 mm)
Basin area, top 65″ (1651 mm) x 26″ (660 mm)
Weight 71 lbs (32.2 kg)
To overflow:
Water depth 15″ (381 mm)
Capacity 72 gal (272.5 L)
* Approximate measurements for comparison only.
Pump: V Hz A
1-speed 120 60 7.5
Heater: kW V Hz A
1.5 120 60 12.5
18"
(457 mm)
Required Electrical Service
Two dedicated circuits required, each protected with
Class A Ground-Fault Circuit-Interrupter (GFCI):
Pump/control 120 V, 15 A, 60 Hz
Heater 120 V, 15 A, 60 Hz
Locate the outlets behind the whirlpool and within 24″
(610 mm) of the pump.
Installation Notes
Install this product according to the installation guide.
Floor support under whirlpool must provide for a minimum of
39 lbs/square foot (189 kg/square meter) loading.
The apron must be installed before the finished floor and wall
materials are installed.
No change in measurements if connected with drain
illustrated. (K-11677)
1-1/4"
(32 mm)
1-1/2"
(38 mm)
1"
(25 mm)
8-1/2"
(216 mm)
2-1/2"
72" (1829 mm)
(64 mm)
1/4" (6 mm)
3" (76 mm)
2-7/8" (73 mm)
Product Diagram
PROFLEX®7236 WHIRLPOOL BATH WITH HEATER
Page2of2
1012988-4-
F
Pump/Control Access
(If Apron Is Not Used)
20" (508 mm) W x
15" (381 mm) H
Lumbar
Angle 34˚
20-1/8"
(511 mm)
Tile Flange
Detail
36" (914 mm)
18-5/8"
(473 mm)
1-1/2" Bath Drain
Drop-in Rim
Detail
Loading...