Kohler K63680 Installation Manual

Installation and Care Guide

Freestanding Bath

Retain serial number for reference:
Conserver le numéro de série pour référence:
Guarde el número de serie para referencia:_____________________

Français, page ″Français-1″
Español, página ″Español-1″

1237787-2-H

Tools and Materials

Plus:

• Drop Cloth

• Shims

• 2x4s

• Wood Blocks

• 1/2" (13 mm) Exterior
Construction
Adhesive

100% Silicone
Sealant

Grade Plywood
(for Rim-mount Faucet)

Before You Begin

NOTICE: Adequate floor support must be provided. Note the model number on the back of the bath,
then visit the product page at kohler.com for additional information.

NOTICE: Before installing a rim-mount bath faucet, refer to the specification sheet on the bath product
page at kohler.com.

NOTICE: Provide adequate backer board support for a rim-mount faucet; large faucets that may be
inadvertently used as a means of support are not safe for this installation.

NOTICE: For Wireless Music Kit: Refer to the instructions included with the music kit for wiring and
installation details.

IMPORTANT! To ensure a successful installation, install the bath on a level, finished floor.

Observe all local plumbing and building codes.

Unpack and inspect the bath and components for damage. Return the bath and components to the
carton until installation.

To simplify future maintenance, make sure all plumbing connections around the bath are easily
accessible.

Carefully plan moving the bath into the installation area. This bath will not easily fit through
doorways.

Two people are needed to install this product.
This bath is designed for freestanding installation only.
If installing a rim-mount faucet, make sure there is no interference above or below the rim before

drilling any holes.
Illustrations shown may not look like your actual product but they still apply to this installation.
This bath conforms to CSA B45.5/IAPMO Z124. All dimensions are nominal.

1237787-2-H 2 Kohler Co.

Bath Rim

Recommended Faucet
Location (See Specification
Sheet for Dimensions)

4" (102 mm)

Minimum
1/2" (13mm)
Plywood

1. Prepare the Rim-Mount Faucet (Optional)

NOTICE: Before installing a rim-mount bath faucet, refer to the specification sheet on the bath product
page at kohler.com for faucet location dimensions for your model.

NOTICE: To accommodate the bath shroud, use flexible connections to attach the water supplies to a
rim-mount faucet.

NOTICE: For rim-mount faucet installations, route the water supply lines high enough to permit access
for making the final connections from above the shroud.

Refer to the specification sheet on the bath product page at kohler.com to determine the
recommended faucet location and drain model for your bath.

Measure and cut a piece of 1/2″ (13 mm) exterior grade plywood to support the faucet. The board
should be 4″ (102 mm) wide. The length should extend beyond the width of the faucet holes to
ensure proper support.

Locate the faucet in the desired location on the bath rim. Make sure the faucet trim fits on the bath
rim without overhanging. Make sure there is no interference above or below the rim before drilling
any holes.

Refer to the installation instructions packed with the faucet to determine faucet hole size.
Use a pencil to mark the faucet hole centerlines. Do not drill the holes at this time.

CAUTION: Risk of product damage. To avoid scratching the bath, position a thin piece of cardboard
under any clamps before tightening.

Position the plywood on the underside of the rim, then clamp in place. Make sure the clamps do
not directly contact the finished surface of the bath.

Carefully drill the faucet holes.
Install the valve according to the installation instructions included with the valve. Do not install the

faucet trim until instructed.

Kohler Co. 3 1237787-2-H

All Other ModelsModels with Support Blocks

Shroud

Shroud

Trace
the hole.

Support Block

2. Prepare the Site

NOTICE: For models with support blocks, do not attempt to remove the hardened casting material
covering the blocks. The casting material is required to properly position and install the bath.

IMPORTANT! To ensure a successful installation, install the bath on a level, finished floor.

IMPORTANT! Make sure the subfloor offers adequate support for the bath.

Temporarily position the bath and shroud in the installation location.
If applicable, remove and discard the thin plastic film covering the support blocks.
Verify that the bath is level. Shim under the bath if necessary, and secure the shims to the bath.
Without moving the shroud, lift and remove the bath from the shroud.
Use the drain area cutout in the shroud to trace the drain hole area on the floor.
Remove the shroud and set it aside.
Refer to the specification sheet on the bath product page at kohler.com to determine any drain

clearance requirements, and cut adequate floor clearance as needed.
Refer to the specification sheet on the bath product page at kohler.com for drain height details.

Position and install a standard PVC or brass bath drain pipe to the correct height.

1237787-2-H 4 Kohler Co.

All Other ModelsModels with Support Blocks

Dry fit the drain.

Attach to the
drain pipe.

Apply construction adhesive
before final positioning.

3. Prepare the Bath

NOTICE: Refer to the drain instructions to dry fit the drain to the bath. Do not cement and complete the
drain installation until instructed.

Dry fit the drain assembly to the bath. Refer to the drain instructions. Do not apply sealant or
cement to the drain components at this time.

Loosen the drain and overflow connections from the bath, and remove the drain assembly from the
bath.

Dry fit the drain assembly to the drain pipe, which has already been cut to the correct height.
Temporarily position the shroud in place over the drain assembly.
With help, temporarily lift the bath into place in the shroud. Make sure the bath rim is completely

seated over the shroud to engage the alignment guides.
Verify that the drain and overflow connections line up properly with the drain and overflow holes

on the bath. Measure and record any adjustments needed to the drain or overflow tube lengths.
Remove the bath and shroud, leaving the drain and overflow assembly attached to the drain pipe.
Adjust the length of the drain tubes as needed to ensure drain alignment with the drain and

overflow holes in the bath.
Repeat these drain fit steps until the drain and overflow connections line up with the drain and

overflow holes in the bath.
Cement and assemble the drain and overflow components. Connect the drain tee to the drain pipe.
Apply 100% silicone sealant to both sides of the drain and overflow gaskets.
Apply slow-drying construction adhesive to the bottom of the shroud.
Carefully position the shroud over the drain, aligning the hole with the traced mark on the floor.

Kohler Co. 5 1237787-2-H

Alignment Guides

Temporary
Blocks

4. Install the Bath

NOTE: To provide access for securing the connections, temporarily position block spacers on opposing
ends between the shroud and the bath rim. Position the blocks to avoid damaging the alignment guides
located under the bath rim. The type of alignment guides may vary by product.

With help, carefully lift the bath into place over the shroud and onto the temporary blocks.
For Wireless Music Kit: Refer to the instructions included with the music kit for wiring and

installation details, and make the final electrical connections.
Secure all drain connections and fittings according to the drain instructions.
For a rim-mount faucet, install the faucet and trim according to the faucet and trim instructions.

Make sure there is adequate support under the bath rim to support the faucet. Refer to the ″Prepare
the Rim-Mount Faucet (Optional)″ section.

Carefully remove the blocks and make sure the bath rim engages the top of the shroud on all sides.
Ensure all alignment guides are inside the shroud; there should be no gap between the bath and the
shroud.

Install the drain flange and overflow cover according to the drain instructions.
Close the bath drain. Fill the bath to the overflow, and check for leaks.
If desired, apply a thin, continuous bead of clear or color-matched 100% silicone sealant to the seam

between the shroud and the finished floor.

Care and Cleaning

For best results, keep the following in mind when caring for your KOHLER product:

•

Always test your cleaning solution on an inconspicuous area before applying to the entire surface.

•

Wipe surfaces clean and rinse completely with water immediately after applying cleaner. Rinse and
dry any overspray that lands on nearby surfaces.

•

Do not allow cleaners to soak on surfaces.

•

Use a soft, dampened sponge or cloth. Never use an abrasive material such as a brush or scouring
pad to clean surfaces.

For detailed cleaning information and products to consider, visit www.kohler.com/clean. To order Care &
Cleaning information, call 1-800-456-4537.

1237787-2-H 6 Kohler Co.

Warranty

ONE-YEAR LIMITED WARRANTY

KOHLER plumbing products are warranted to be free of defects in material and workmanship for one year
from date of installation.

Kohler Co. will, at its election, repair, replace or make appropriate adjustment where Kohler Co. inspection
discloses any such defects occurring in normal usage within one (1) year after installation. Kohler Co. is not
responsible for removal or installation costs. Use of in-tank toilet cleaners will void the warranty.

To obtain warranty service contact Kohler Co. either through your Dealer, Plumbing Contractor, Home
Center or E-tailer, or by writing Kohler Co., Attn.: Customer Care Center, 444 Highland Drive, Kohler, WI
53044, USA, or by calling 1-800-4-KOHLER (1-800-456-4537) from within the USA and Canada, and
001-800-456-4537 from within Mexico, or visit www.kohler.com within the USA, www.ca.kohler.com from
within Canada, or www.mx.kohler.com in Mexico.

IMPLIED WARRANTIES INCLUDING THAT OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE ARE EXPRESSLY LIMITED IN DURATION TO THE DURATION OF THIS
WARRANTY. KOHLER CO. AND/OR SELLER DISCLAIM ANY LIABILITY FOR SPECIAL,
INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states/provinces do not allow limitations on how

long an implied warranty lasts, or the exclusion or limitation of special, incidental or consequential damages,
so these limitations and exclusions may not apply to you. This warranty gives you specific legal rights. You
may also have other rights which vary from state/province to state/province.

This is Kohler Co.’s exclusive written warranty.

Kohler Co. 7 1237787-2-H

Guide d’installation et d’entretien

Baignoire autoportante

Outils et matériel

Adhésif de
construction

Mastic à la
silicone à 100%

Plus:

• Toile de protection

• Cales

• Montants 2x4

• Blocs en bois

• Contreplaqué extérieur

1/2" (13 mm)
(pour robinet monté sur le rebord)

Avant de commencer

AVIS: Un support de plancher adéquat doit être fourni. Noter le numéro de modèle se trouvant sur
l’arrière de la baignoire, puis visiter la page du produit sur le site kohler.com pour obtenir de l’information
supplémentaire.

AVIS: Avant d’installer un robinet de baignoire à montage sur rebord, se reporter à la fiche de
spécifications de la page du produit de la baignoire sur le site kohler.com.

AVIS: Fournir un support avec planche d’appui adéquat pour un robinet à montage sur rebord; les
robinets de grande taille qui auraient été utilisés par inadvertance comme moyen de support ne sont pas
sécuritaires pour cette installation.

AVIS: Pour kit de musique sans fil: Se reporter aux instructions accompagnant le kit de musique en ce
qui concerne le câblage et les détails d’installation.

IMPORTANT! Pour assurer une installation réussie, installer la baignoire sur un plancher fini de niveau.

Respecter tous les codes de plomberie et de bâtiment locaux.

Déballer et inspecter la baignoire et les composants pour détecter tout dommage. Remettre la
baignoire et les composants dans l’emballage jusqu’à l’installation.

Pour simplifier la maintenance future, s’assurer qu’il est possible d’accéder sans difficulté à toutes
les connexions de plomberie autour de la baignoire.

Planifier avec attention le déplacement de la baignoire dans l’emplacement d’installation. Cette
baignoire ne passe pas facilement par les entrées de portes.

Deux personnes sont nécessaires pour installer ce produit.
Cette baignoire est conçue pour une installation autoportante uniquement.

Kohler Co. Français-1 1237787-2-H