Installation Guide
Single-Control Kitchen Sink Faucets
K-6352 K-6353
M product numbers are for Mexico (i.e. K-12345M)
Los números de productos seguidos de
M corresponden a México (Ej.
K-12345M)
Français, page“ Français-1”
Español, página“ Español-1”
1025494-2-B
Tools and Materials
Assorted
Screwdrivers
Adjustable
Wrench
Plumbers
Putty
Pipe
Wrench
Strap
Wrench
5/64" Hex
Wrench
Thread
Sealant
Tube Cutter
Socket Wrench with
7/16" Deep Socket
Pliers
Thank You For Choosing Kohler Company
We appreciate your commitment to Kohler quality. Please take a few
minutes to review this manual before you start installation. If you
encounter any installation or performance problems, please don’t
hesitate to contact us. Our phone numbers and web site are listed on
the back cover. Thanks again for choosing Kohler Company.
Before You Begin
Observe all local plumbing codes and building codes.
Shut off the water supplies.
Carefully inspect waste and supply tubing for any sign of
damage and replace if necessary.
For new installations, assemble the faucet and drain to the sink
before installing it.
Before installation, unpack the new faucet and inspect it for
damage. Return the faucet to the carton until you are ready to
install it.
Do not remove the faucet ground joints, as they contain
important back-siphonage protection.
Do not attach a dishwasher to the faucet spray outlet.
Kohler Co. reserves the right to make revisions in the design of
faucets without notice, as specified in the Price Book.
1025494-2-B 2 Kohler Co.
Faucet Body
Hose
Escutcheon
Rubber
Washer
Spacer
O-Ring
1. Install the Mounting Stud
Disconnect the hose from the hose connector.
Screw the mounting stud into the threaded hole at the bottom of
the faucet body. The mounting stud should extend slightly
beyond the threaded hole in the body.
1. Install the Escutcheon (Optional)
NOTE: For installation on marble, do not use plumbers putty. Use
the self-adhesive gaskets provided. Remove the paper backing and
apply the gaskets (adhesive side down) over the outside holes.
For 1-hole Installations:
The escutcheon, spacer, and O-ring are not required. .Slide the
rubber washer over the faucet tubing and hose.
Insert the faucet tubing and hose into the hole.
For 3–hole Installations:
Apply a ring of plumbers putty to the underside of the
escutcheon according to the putty manufacturer’s instructions.
Insert the O-ring into the groove in the spacer.
Slide the rubber washer, escutcheon, and spacer (O-ring side
down) over the faucet tubing and hose.
Insert the faucet tubing and hose into the center hole, carefully
aligning the escutcheon.
Press down on the escutcheon and remove any excess putty.
Kohler Co. 3 1025494-2-B
Hose
Connector
Bracket
Washer
Nut
Weight Screw
Weight
Hose
23" (58.4 cm)
3" (7.6 cm)
or Larger
Hot
1. Faucet Installation
From the underside of the sink, position the bracket, washer and
nut onto the mounting stud.
Position the faucet and escutcheon on the sink to obtain the
desired alignment.
Tighten the nut securing the faucet to the sink. For best access,
use a socket wrench with a 7/16” deep socket.
NOTE: The weight must be installed to act as a pull stop and to
prevent kinking damage to the hose.
For best performance, attach the weight to the hose 23” (58.4cm)
from the loose end of the hose. The weight may be moved to
adjust the pull-out length of the hose.
Carefully tighten the weight screws. Do not overtighten.
Reconnect the hose to the hose connector.
Cold
2. Install the Supplies
CAUTION: Risk of restricted waterflow and product damage.
Use extreme care to avoid kinking and twisting when connecting
the hoses. Hoses must not be taut when installed.
CAUTION: Risk of back siphonage. Do not remove the ground
joints from this faucet. The ground joints contain very important
back-siphonage protection. .
1025494-2-B 4 Kohler Co.
Install the Supplies (cont.)
Install the sink using the sink manufacturer’s instructions.
Connect the supply hoses to the supply stops.
Tighten all connections.
Kohler Co. 5 1025494-2-B
3. Installation Checkout
Ensure that all coupling nuts are tight.
Ensure that the lever handle is in the down position.
Open the drain.
Remove the sprayhead and screen from the end of the hose.
Position the hose in the sink.
Turn on the main water supply and open the valve for one
minute to flush the fitting.
Reattach the spray and screen. Turn on the water and check for
leaks. Adjust as needed.
1025494-2-B 6 Kohler Co.
Bonnet
Handle
Setscrew
Stop
Tab
Mounting Nut
Valve Stem
Top Disc
Indexer
Splines
4. Water Temperature Adjustments
NOTE: Prior to adjustment, make sure the handle is in the
maximum hot position.
Remove the setscrew, handle, and bonnet.
Turn on the water to the maximum temperature by pushing the
valve stem up and turning it clockwise.
Mark the current position of the temperature stop tab (top edge)
on the mounting nut with a marker or pencil.
Lift the indexer and top disc just enough to clear the valve
splines and to allow rotation.
NOTE: Each spline notch is an average 9.5_F (5.3_C) change in
temperature.
Turn the indexer, top disc, and valve stem counterclockwise until
the desired temperature is achieved.
Reinstall the indexer and top disc to the valve, making sure the
top disc is snapped fully into the indexer.
Turn off the water by pulling the valve stem down.
Reinstall the bonnet, handle, and setscrew.
Kohler Co. 7 1025494-2-B
USA: 1-800-4-KOHLER
Canada: 1-800-964-5590
México: 001-877-680-1310
kohler.com
©2004 Kohler Co.
1025494-2-B
Loading...