KOHLER K-3361, K-3362, K-3363, K-3369 User Manual
Installation Guide
Stainless Steel Kitchen Sinks
K-3361 K-3362
K-3363 K-3369
M product numbers are for Mexico (i.e. K-12345M)
Los números de productos seguidos de
M corresponden a México (Ej.
K-12345M)
Français, page “Français-1”
Español, página“ Español-1”
1013270-2-D
Thank You For Choosing Kohler Company
We appreciate your commitment to Kohler quality. Please take a few
minutes to review this manual before you start installation. If you
encounter any installation or performance problems, please don’t
hesitate to contact us. Our phone numbers and website are listed on
the back cover. Thanks again for choosing Kohler Company.
Tools and Materials
Safety
Glasses
Silicone
Sealant
Measuring
Tape
Pipe Wrench
Pencil
Plumbers
Putty
Drill
Plus:
• Level
• 5/16" Deepwall Socket or
5/16" Nut Driver
• Keyhole/Jigsaw
• Gloves
Putty Knife
Before You Begin
WARNING: Risk of personal injury. Metal surfaces are sharp
and can cause severe cuts. Use gloves and handle sink edges
carefully.
Observe all local plumbing and building codes.
Shut off the hot and cold water supplies.
Prior to installation, unpack the new sink and inspect it for
damage. Return the sink to its protective carton until you are
ready to install it.
Inspect the drain and supply tubing. Replace if necessary.
All information in these instructions is based on the latest product
information available at the time of publication. Kohler Co.
reserves the right to make changes at any time without notice.
1013270-2-D 2 Kohler Co.
Sink
Sink Outline
Countertop
Pilot
Hole
1/4"
(6 mm)
Trace the outline of the sink on
the countertop with a pencil at the
Create a second line 1/4" (6 mm)
in from the original sink outline.
desired installation location.
1. Preparation
WARNING: Risk of personal injury. Metal surfaces are sharp
and can cause severe cuts. Use gloves and handle sink edges
carefully.
For new installations:
Carefully place the sink upside down on the countertop in the
desired position. Be careful not to damage the sink finish.
Make sure the sink will not interfere with the cabinet.
Trace the sink outline onto the countertop. Do not cut along the
outline.
For existing installations:
Carefully lift the old sink out of the countertop.
Compare the existing cut-out to the required cut-out size.
If needed, enlarge the cut-out hole according to the directions for
new installations.
For all installations:
Draw a line 1/4″ (6 mm) inside the sink outline.
Before cutting, measure the cut-out line you just drew and
compare it to the overall sink dimensions. The cut-out should be
1/2″ (1.3 cm) smaller than the overall sink dimensions.
Kohler Co. 3 1013270-2-D
Preparation (cont.)
Drill a pilot hole inside the cutting line. Using a jig or keyhole
saw, cut along the inside line to cut out the opening in the
countertop.
1013270-2-D 4 Kohler Co.
Clip
Tooth
Clip Jaw
Mounting Holes
Hex Nut
Clip Placement
2. Install the Clips
Turn the sink upside down onto a clean, soft surface.
Slide the clips over the predrilled mounting holes in the sink rim.
Refer to the illustration for correct clip positions (three clips on
the front and back; two on each side).
NOTE: Make sure the clip teeth are fully seated in the mounting
hole.
Turn all the clip jaws parallel to the sink rim.
3. Install the Faucet Fitting
Install the faucet and drain fitting according to the manufacturer’s
instructions.
NOTE: If you are reusing fittings from an old sink, use plumbers
putty under the faucet base and top flange of the strainer.
Kohler Co. 5 1013270-2-D
Countertop
Clip Jaw
Sink
Installation Clips
Cut-Out
Hex Nut
4. Install the Sink
Apply a bead of quality sealant to the underside of the sink rim.
NOTE: The fasteners may need to be repositioned to compensate for
an uneven countertop.
Squarely position the sink onto the cut-out area.
Rotate the clip jaws underneath the countertop, as illustrated.
Tighten the hex nuts to lower the sink rim down onto the
countertop. Do not overtighten.
Use a dry cloth to wipe away any excess sealant.
Verify that there are no gaps.
Allow the sealant to cure for at least 30 minutes.
Install the garbage disposal, if used, according to the
manufacturer’s instructions.
Connect and tighten the trap to the strainer, and complete the
water supply connections to the faucet according to the
instructions packed with the faucet.
Run water into the sink and check for leaks.
1013270-2-D 6 Kohler Co.
Loading...