Kohler K14234SPG9 Installation Manual
COUNTERTOP LAVATORIES
R
BEFORE YOU BEGIN
Carefully read these instructions before you attempt to remove your
old lavatory.Before installingyour new lavatory,make sureyou have
the proper materials necessary to complete the job. This will help
you avoid costly mistakes.
Do not install this lavatory on a glass countertop. The weight of the
lavatory may damage the glass.
Your new Kohler fixture has been designed for installation using
common tools.
K-2184 Chenille
K-2199 Cantata
K-2217 Linia
K-2220 Vintage
K-2264 Centerpiece
K-2292 Intaglio
K-2298 Compass
K-2332 WaterCove
K-14156 Garland
K-14170-RB Provincial
K-14173 Fables and Flowers
K-14234-BT Botanical Study
K-14234-SP Serpentine Bronze
K-14246-AC Ocellus Citron
K-14246-AS Ocellus Skylight
K-14270-PS Peonies and Ivy
K-14271-WF Prairie Flowers
K-14272-BR Briar Rose Floral.......................
K-14272-P Pheasant
K-14272-TF Ankaras
t.................................
t.................................
t....................................
t.................................
t.............................
r..................................
t...............................
t..............................
t................................
t...........................
t......................
t......................
t....................
t.......................
t......................
t......................
t.......................
t.............................
t.............................
WITHOUTFAUCETDECK
Materials required:
D PLUMBERS PUT TY
D NEW FAUCET(OPTIONAL)
D SHUT-OFF VALVES(OPTIONAL)
D SAFETY GLASSES
Before you remove your old fixture, unpack the new lavatory and
carefully inspect it for any damage that may have occured. Vitreous
china and enameled cast iron may chip, and you
discover damage after the unit has been installed. Until you are
ready to begin installation, set the lavatory back in the original
packing carton to prevent damage.
Make sure you have a cut-out template to aid you in locating
your faucet centerline on the countertop, and incutting outyour
countertop.
do not want to
Tools required:
D PUTTY KNIFE
D ADJUSTABLE WRENCH
D SABER OR KEYHOLE SAW
D PIPE WRENCH
D TUBING CUTTER
D SCREWDRIVER
D HACKSAW
D RULER
D PENCIL
D DRILL
D 1/2” DRILL BIT
D 1-3/16” HOLE SAW
D 1-3/8” HOLE SAW (FOR WIDESPREAD FAUCETS)
D CUT-OUT TEMPLATE (FURNISHED WITH FIXTURE)
1007251-2-
B
Français, Page 6
Español, Página 11
E2003 Kohler Co.
LOCATING THE FAUCET CENTERLINE
DRAW PRELIMINARY FAUCET CENTERLINE
This lavatory is a unique installation with the faucet fittings mounted
on the countertop rather than on the lavatory itself.
The best location of the faucet centerline is determined by three
items: the size of the fitting or faucet spout escutcheons, length of
faucet spout, and clearance between the faucet spout and lavatory
rim.
FAUCET LOCATION
1.Refer to Fig. #1 . Determine if the faucet spout escutcheon or
faucet handle escutcheon will be closer to the lavatory rim
when installed. Items to consider are the sizes of the different
faucet components and the lavatory shape. The escutcheon
found to be closest to the lavatory rim will be used in step 2.
X
XX
Faucet Handle Escutcheon
Faucet Spout Escutcheon
Lavatory Rim
NOTE: The following instructions refer to the installation of
Model K---2332, in an above counter installation.
NOTE: Wall-mount faucet installations: Be sure to provide
sufficient spout overhang into the lavatory basin. Make surethat
the water stream is directed to the center of the lavatory and
there is sufficient hand washing clearance.
NOTE: Countertop faucet installations: Pay special attention
tothe spout and handlefit clearancewhen locatingthe faucet,as
noted below.
Countertop faucet installations: Use the template to locate the
faucet spouthole centerline to provideadequate clearance between
the edge of the lavatory and the spout.
Refer to Fig. #2 . Check for adequate clearancebetween the backsplash, faucet spoutand handles and lavatory.Kohler recommends
clearance of at least 1” (2.5cm) between:
D the installed lavatory and the faucet spout;
D the installed lavatory and the end of the faucet handles
D the faucet spout and handles, and the backsplash.
Refer to the faucet installation instructions for the required
clearance, and mark the preferred faucet hole locations.
Spout
Centerline
Backsplash
;
Fig. #1
2.Measure the escutcheon, front-to-back, that was found to be
closest to the rim in step 1. This escutcheon measurement
may also be found on the faucet roughing-in page.
3.Divide the front-to-back dimension in half, and add 1/4”.
Standard sizes are shown in the chart on the next page. The
distance found will be used to draw the preliminary faucet
centerline.
NOTE: For all front to back dimensions, round up to the nearest
1/16” (2mm) if required.
FRONT TO
BACK DIMENSION
2” (5cm) 1-1/4” (3.2cm)
2-1/8” (5.4cm) 1-5/16” (3.3cm)
2-1/4” (5.7cm) 1-3/8” (3.5cm)
2-3/8” (6cm) 1-7/16” (3.7cm)
2-1/2” (6.4cm) 1-1/2” (3.8cm)
DISTANCE TO DRAW CENTERLINE
BEHIND REFERENCE LINE
Cut-out
Line
Fig. #2
1”(2.5cm)
Minimum
Clearance
Outside Edge
of Lavatory
1-1/4”(3.2cm)
Minimum
Clearance
1007251-2-
B
2
Kohler Co.
DRAW PRELIMINARY FAUCET CENTERLINE
1. Draw the distance determined in FAUCET LOCATION as the
preliminary centerline on the cut-out template. It should be parallel
and behind the cut-out template reference line (located on the
cut-out template).
NOTE: On the full-size rim section found on the cut-out
template, mark the preliminary faucet centerline dimension.
This will be used to DETERMINE FINAL FAUCET CENTER-
LINE.
DETERMINE FINAL FAUCET CENTERLINE
NOTE: If you are installing a tiled-in lavatory,proceed toStep 1B.
The preliminary faucet line from DRAW PRELIMINARY
FAUCET LINE is the final faucet line in this case.
1. When this preliminary faucet centerline has been drawn the
spout must be checked for three items:
A. Refer to Fig. #2. For low profile faucet spouts, the
distance between the faucet spout and the lavatory rim must be a
minimum of 1/4” (6mm). Use the faucet spout, the preliminary
faucet centerline,and the full size rim sectionon the cut-outtemplate
to check this. If there is not 1/4” (6mm) clearance, move the
preliminary faucet centerline back. Recheck the clearance until you
have 1/4”(6mm). Measure the distanceof the new faucet centerline.
Redraw the new faucet centerline behind the reference line on the
cut-out template. Remark this dimension on the full size rim section.
This is the final faucet centerline.
2” (5cm)
Min.
Fig. #4
Air
Gap
FAUCET CLEARANCE WITH BACKSPLASH
NOTE: 2-1/2” (6,4cm) of space is requiredfor the KohlerBravura
widespread and Cirrus Sheetflow faucet spouts.
1.Refer to Fig. #4. Draw a line 2” (5cm) behind the final faucet
centerline on the cut-out template. This is the minimum backsplash
locator line. It is drawn to ensure adequate clearance behind the
faucet for proper installation. It will also help position the lavatory on
the countertop. Cut along this backsplash locator line. Save the
section of the cut-out template with the lavatory rim and cut-out
lines.
Countertop Backsplash Backsplash Locator Line
2”
(5cm)
C
L of Fitting
1/4” (6mm)Min.
2” (5cm) Min.
Fig. #3
B. Refer to Fig. #3. Check to be sure the water stream will
project 2” (5cm) minimum into the lavatory basin to allow adequate
area for hand washing.Use the approximate faucet spout angle,the
final faucet centerline and the full-size rim section from the cut-out
template to ensure this clearance. If this cannot be accomplished,
the faucet is not optimally matched for this lavatory and may not
operate on this lavatory to the owner’s satisfaction. You may wish to
consider an alternate faucet.
C. Refer to Fig. #3. Check for compliance with all state and
local plumbing codes, including air gap standards.
Cut-Out T emplate
On Countertop
Countertop
Fig. #5
INSTALLATION
1. To remov e old lav atory, turn off water supp lies. Turn the
lavatory faucet on to drain water from the lines. Disconnect and
remove water supply tubes. Disconnect drain and remove trap.
CAUTION: To remove steel frame lavatories, remove
clips or fasteners under lavatory that hold lavatory to counter.
Do not remove clips that hold frame to fixture.
1007251-2-
B
3
Kohler Co.
2. Lift lavatory out of countertop with fitting and drain attached, if
applicable.
3. Refer to Fig. #6 . Cut out inside of cut-out template with
scissors on the inside line.
Fig. #6
5. Refer to Fig. #8 . Drill a pilot hole into the countertop using a
1/2” drill. Use a saber or keyhole saw to cut out opening by carefully
following the pencil line traced from cut-out template. T emporarily
position lavatory into counter, and trace a light pencil line around
the outside edge. This will serve asa guideline for applying sealant.
Remove fixture from countert op.
NOTE: The rim must be traced so the sealant will cover and
conceal the pencil line.
4. Refer to Fig. #7 . Set the cut-out template on the countertop
so the backsplash locator line is touching the countertop
backsplash. The cut-out template can be moved forward from this
position to get the best placement of the lavatory on the countertop.
Tracethe cut-out opening on the countertop using asoft lead pencil.
Centerlines are provided to help align opening. Mark the final
centerline on the countertop using the cut-out template. Drill the
faucet holes using the following chart to determine their size.
NOTE: If there is not enough room at the front of the counter for
the lavatory rim, a larger countertop is needed.
Dimensions Are For Kohler Faucets Only. When Using Other
Faucets, Contact Supplier For Installation Instructions And
Dimensions.
FAUCET CENTERS VALVE HOLES SPOUT HOLE
4” (10.2cm) 1-3/16” (3cm) 1-3/16” (3cm)
6” (15.2cm)
8” (20.3cm)
12” (30.5cm)
16” (40.6cm)
Faucet Escutcheon Handle Escutcheon
Backsplash
1-3/8” (3.5cm) 1-3/16” (3cm)
Centerline
1/4” (6mm) Min.
Fig. #8
6. Install faucet to countertop and drain to lavatory following
manufacturer’s instructions.
7. Refer to Fig. #9 . Apply two ribbonsof plumbersputty orother
sealant on the counter from the edge of the opening to edge of rim
as measured in Step 5 according to the putty manufacturer’ s
instructions. Quickly spread putty or sealant with a putty knife.
Plumbers Putty
Lavatory
Countertop
Fig. #9
8. Set lavatory into position. Immediately wipe away any excess
putty or sealantwith a damp cloth.Fill in any voids between rim and
countertop.
9. Allow putty or sealant to set for 30 minutes. Connect supply
lines at supply valves and fitting. Assembleadjustable drain pop-up
linkage. Connect drain, trap, and outlet. Turn tailpiece into drain
body. Align trap inlet with tailpiece. Insert trap nut and gasket onto
tailpiece, and insert into trap. Tailpiece must extend 1” to 2” into trap.
Tailpiece may have to be cut to fit. Turnon water and check for leaks.
Countertop
1007251-2-
10. CARE AND CLEANING. DO NOT USE ABRASIVE
CLEANSERS as they m ay scra tch the surf ace of this fixtu re.
Fig. #7
B
Clean up with a non-abrasive cleaner.Stubborn stains, paint, ortar
may be removed with turpentine or paint thinner.
4
Kohler Co.
CALL US FOR HELP
Here’s what you need to do if you require service:
First review the installation instructions to ensure correct installation. For additional assistance in the USA, call our
Customer Service Department for direct help. You may also contact us at our web site listed below.
Call 1-800-4-KOHLER within the U.S.
Call 1-800-964-5590 within Canada
Call 001-877-680-1310 within Mexico
kohler.com
E2003 Kohler Co.
1007251-2-
B
5
Kohler Co.
Loading...