Kohler K1239CB96 User Manual
MARIPOSA
®
Features
Acrylic
•
Drop-in
•
5 individually adjustable ProFlex
•
Pump with air switch and grounding-type plug-in cord
•
Optional K-9695 metal finish 5 jet trim kit
•
Optional K-1278 removable apron
•
60″ (1524 mm) x 36″ (914 mm) x 20″ (508 mm)
•
hydro-massage jets
®
Codes/Standards Applicable
Specified model meets or exceeds the following:
ASME A112.19.7
•
UL 1795
•
CSA B45.5/IAPMO Z124
•
Specified Model
CUSTOM BATH WHIRLPOOL
K-1239-CB
Colors/Finishes
0: White
•
Other: Refer to Price Book for additional colors/finishes
•
Accessories
CP: Polished Chrome
•
PB: Vibrant®Polished Brass
•
Other: Refer to Price Book for additional colors/finishes
•
Model Description Colors/Finishes
K-1239-CB Custom bath whirlpool – drop-in ❑ 0 ❑ Other_____
Recommended Accessories
K-7161-AF Adjustable pop-up drain with tailpiece ❑ CP ❑ PB ❑ Other_____
Optional Accessories
K-1278 Removable apron ❑ 0 ❑ Other_____
K-9695 Metal finish 5 jet trim kit ❑ CP ❑ PB ❑ Other_____
Product Specification
The acrylic bath whirlpool shall be 60″ (1524 mm) in length, 36″ (914 mm) in width, and 20″ (508 mm) in height. Bath whirlpool
shall be for drop-in installation. Bath whirlpool shall have 5 individually adjustable Proflex
switch and grounding-type plug-in cord. Bath whirlpool shall be available with an optional K-1278 removable apron and an
optional K-9695 metal finish 5 jet trim kit. Bath whirlpool shall be Kohler Model K-1239-CB-____.
Page 1 of 2
1014713-4-
E
hydro-massage jets, a pump with air
®
USA/Canada: 1-800-4KOHLER
(1-800-456-4537)
www.kohler.com
MARIPOSA
®
Technical Information
Required Electrical Service
Fixture*:
Bathing well:
Basin area, bottom 46″ (1168 cm) x 24″ (610 mm)
Basin area, top 54″ (1372 mm) x 27″ (686 mm)
Weight 105 lbs (47.6 kg)
To overflow:
Water depth 14″ (356 mm)
Capacity 63 gal (238.5 L)
* Approximate measurements for comparison only.
Drop-in cutout: 58″ (1473 mm) x 34″ (864 mm)
Pump: V Hz A
1-speed 120 60 7.5
7-1/2"
(191 mm) Max
Dedicated circuit required, protected with Class A
Ground-Fault Circuit-Interrupter (GFCI):
Pump/control 120 V, 15 A, 60 Hz
Locate the outlet behind the whirlpool and within 24″
(610 mm) of the pump.
Installation Notes
Install this product according to the installation guide.
Floor support under whirlpool must provide for a minimum of
44 lbs/square foot (214 kg/square meter) loading.
If installing a rim-mount faucet, make sure there is no
interference with the drain overflow and circulating system
before drilling any holes. If installing a spout on the faucet
deck, consult local and national codes for minimum air gap
requirements.
The apron must be installed before the finished floor and wall
materials are installed.
Pump must be relocated to custom position at the time of
installation. Provide adequate clearance.
No change in measurements if connected with drain
illustrated. (K-7161-AF or K-7161M-AF)
Recommended Faucet Area
Pump/Control
Access
20" (508 mm) W x
15" (381 mm) H
18"
(457 mm)
1-11/16"
(43 mm)
8-11/16" (221 mm)
3-1/2"
(89 mm)
3"
(76 mm)
MARIPOSA®CUSTOM BATH WHIRLPOOL
Page2of2
1014713-4-
E
60" (1524 mm)
2-7/8"
1" (25 mm)
(73 mm)
Product Diagram
20"
(508 mm)
1-1/2"
(38 mm)
Drop-in Rim
Detail
36" (914 mm)
18-1/2"
(470 mm)
1-1/2" OD
Loading...