TERCET
®
Features
Acrylic
•
Pump with air switch and grounding-type plug-in cord
•
6 individually adjustable ProFlex
•
Drop-in
•
In-line heater
•
Molded lumbar supports and armrests
•
Textured bottom surface
•
Optional K-9696 whirlpool trim kit in various finishes
•
Integral tile flange on both sides for corner
•
installation. [K-1160-FH]
60″ (1524 mm) x 60″ (1524 mm) x 21″ (533 mm)
•
hydro-massage jets
®
Codes/Standards Applicable
Specified model meets or exceeds the following:
ANSI Z124.1.2
•
ASME A112.19.7
•
UL 1795
•
ASTM E162
•
ASTM E662
•
BATH WHIRLPOOL WITH HEATER
K-1160-H
ALSO K-1160-FH
Colors/Finishes
0: White
•
Other: Refer to Price Book for additional colors/finishes
•
Accessories
0: White
•
CB: Polished Chrome/Polished Brass
•
PB: Polished Brass
•
Other: Refer to Price Book for additional colors/finishes
•
Specified Model
Model Description Colors/Finishes
K-1160-H Bath whirlpool – drop-in (shown) ❑ 0 ❑ Other_____
K-1160-FH Bath whirlpool – integral tile flange ❑ 0 ❑ Other_____
Recommended Accessories
K-11677 Adjustable trip lever bath drain ❑ CP ❑ PB
Optional Accessories
K-1491 Pillow ❑ 0 ❑ Other_____
K-1601 Footstop ❑ 0 ❑ Other_____
K-9696 Jet trim kit (metal finishes) ❑ CP ❑ PB ❑ Other_____
Product Specification
The drop-in acrylic bath whirlpool shall be 60” (1524 mm) in length, 60″ (1524 mm) in width, and 21” (533 mm) in height. Product
shall have 6 individually adjustable ProFlex hydro-massage jets, a pump with air switch and grounding-type plug-in cord, and
an in-line heater. Product shall have a textured bottom surface and molded lumbar supports and armrests. Product shall have
integral tile flange on both sides for corner installation [K-1160-FH]. Product shall have an optional K-9696 whirlpool trim kit in
various finishes. Bath whirlpool shall be Kohler Model K-1160-H______ or K-1160-FH-______.
Page 1 of 2
1041916-4-
USA/Canada: 1-800-4KOHLER
D
(1-800-456-4537)
www.kohler.com
TERCET
®
Technical Information
Required Electrical Service
Fixture*:
Basin area:
Bathing well 52” (1321 mm) x 38-3/4” (984 mm)
Top area 61” (1549 mm) x 46-1/4” (1175 mm)
Weight 131 lbs (59.4 kg)
To overflow:
Water depth 15” (381 mm)
Capacity 96 gal (363.6 L)
* Approximate measurements for comparison only.
Pump: V Hz A
1-speed 120 60 7.5
Heater: kW V Hz A
1.5 120 60 12.5
Minimum access panel
(required):
20″ (508 mm) W x
15″ (381 mm) H
63"
(1600 mm)
35"
(889 mm)
Two dedicated circuits required, each protected with
Class A Ground-Fault Circuit-Interrupter (GFCI):
Pump/control 120 V, 15 A, 60 Hz
Heater 120 V, 15 A, 60 Hz
Locate the outlets behind the whirlpool and within 24”
(610 mm) of the pump and heater.
Installation Notes
Install this product according to the installation guide.
Floor support under whirlpool must provide for a minimum of
39 lbs/square foot (189 kg/square meter) loading.
No change in measurements if connected with
drain illustrated. (K-11677 or K-11677M)
Recommended faucet area
35"
(889 mm)
60"
(1524 mm)
13-1/8"
(333 mm)
29" (737 mm)
60" (1524 mm)
21"
(533 mm)
19-1/2"
(495 mm)
1/2" (13 mm)
TERCET®BATH WHIRLPOOL WITH HEATER
Page2of2
1041916-4-
D
29"
(737 mm)
Pump/Control Access
4-7/8"
(124 mm)
43-3/4"
(1111 mm)
2-7/8"
(73 mm)
3"
(76 mm)
Ø 1-1/2"
Product Diagram
1-1/4"
(32 mm)
Tile Flange
57-1/2"
(1461 mm)
2-7/8"
(73 mm)
Detail
135˚
27-1/2"
(699 mm)
1-1/2"
(38 mm)
Drop-In
Rim Detail
Drop-In Rim Style
Cut-Out Detail