Kohler 492T, 486T, 488T, 490T, 10454T Installation Instructions Manual

BEFORE YOU BEGIN

All information is based on the latest product information available at the time of publication. Kohler Co. reserves
the right to make changes in product characteristics, packaging, or availability at any time without notice.
Please leave these instructions for the consumer. They contain important information.

NOTE:

These products should be located and mounted toawall. While it is possible to mount them to any surface, a stud
or concrete mounted product will yield the best results.

DANGER: (Risk of personal injury )

These products are not designed or intended for use asagrab bar or support bar. Do not install where the product
might be used as a grab or support bar.

1243009-2A-A 1

ROUGH-IN DIMENSIONS

ACCESSORY INSTALLATION INSTRUCTIONS

**Color code must be specified when ordering

ACCESSORY SERVICE PARTS

485T 18″ Towel Bar
486T 24″ Towel Bar
487T Towel Ring
488T Glass Shelf
490T TP Holder
492T Robe Hook

10454T Dual TP Holder
10456T Soap Dish
37352T Covered TP Holder
37353T 24″ Double Towel Shelf
37354T Toilet Brush Holder
37355T 24″ Double Towel Bar

1104400**

1104400**

57597

1002853**

1093960**

1104399**

1046290

59608

1061576

1041023

1001912

1243009-2A-A 8

10454T Dual TP Holder

485T

504

457

25

47

72

84

7

486T

72

84

25

47

609
656

25

47

629

676

132

488T

7

7

33

33

33

1243009-2A-A 2

487T 490T 492T

47

181

25

84

72

162

155

47

84

81
84

47

47

25

54

47

25

124

90

7

7

7

96

119~144

84

33

33

33

119~144

170~195

170~195

387~437

Ø39

103.5

25
47

10454T

78

Ø120

54

25

47

142

82

33

10456T

7

73

128

33

25

157

127

37352T

7

37354T

25

72

130

346

47

47

86

156

75

47

47

1061576

1001912

57597

1002853**

1041023

1046290

59608

1041023

52092

1057882**

(457 mm)
(610 mm)

1057883**

52307

1001886**

1003079**

1001885**

1041023

52307

1003079**

870973

1157348**

1157348**

870973

1157348**

870973

77434

ACCESSORY SERVICE PARTS

1243009-2A-A 7

**Color code must be specified when ordering

485T 18″ Towel Bar
486T 24″ Towel Bar
488T Glass Shelf
37353T 24″ Double Towel Shelf
37355T 24″ Double Towel Bar

Only for 488T

33

33

33

33

65

7

7

1243009-2A-A 3

7

7

25.4

25.4

33

37355T

37353T

600

146

647

47

47

79

33

72

216

610

47

662

120

47

38

104.5

How To Install The Bracket

Only For 485T/486T/488T/37353T/37355T

As Fig 1 shown, select a proper position on the wall to stick the templet, ensure

the templet is horizontal and keep the smaller hole downward as shown. Drill
hole in the finished wall as required.

Only For 10454T

Select a location to install tissue holder. As Fig.2 shown, mark the center point
on the finished wall, and keep the center-to-center distance at 170~195mm.
Use a level to ensure that all center points are horizontal and equidistance.

Mark anchor(1) hole location vertically 12.7mm above and below the center
point as Fig.3 shown. Drill hole in the finished wall as required.

Note: Ensure that all center points are horizontal, otherwise may result in slant
of tissue holder.

Only For 487T/490T/492T/10456T/37352T/37354T

Select a location on the vertical wall to install the bracket. As Fig 4 shown, mark
anchor mounting hole location on wall as shown, ensure the large slotted
mounting hole of the plate upward, the smaller hole of the plate downward and
two screw holes are vertical. Drill hole in the finished wall as required.

For All Products

As Fig 5 shown, press the anchor(1) into the hole. Orienting the large slotted

mounting hole of the plate upward, the smaller hole of the plate downward and
two screw holes are vertical, secure the plate(2) with the self-tapping screw(3).

PN: XXXXXXX

3

2

1

Fig.1

170~195mm

12.7mm

12.7mm

170~195mm

Fig.2

Fig.3

Fig.4

Fig.5

INSTALLATION

Center point

Mounting hole

Level

Center point

ACCESSORY SERVICE PARTS

1046290

1061576

57597

1002853**

1001912

59608

1041023

1169924

1119664

1119648**

1093960**

79138

79138

1001740**

36715**

487T Towel Ring
490T TP Holder
492T Robe Hook
10456T Soap Dish
37352T Covered TP Holder
37354T Toilet Brush Holder

1014802

1243009-2A-A 6

**Color code must be specified when ordering

1243009-2A-A 4

How To Install The Bonnet

Position the escutcheon(4), if included, onto the bonnet(6).

Slide the bonnet onto the bracket(2). Orient the setscrew hole of the bonnet
downward. Make sure the bonnet pin(5) engage the indexing hole in the back
of the escutcheon, if applicable. Insert a screw(7) into the bonnet and tighten.

NOTE: Make sure the bonnet pin engage into the escutcheon hole.

5

2

4

6

7

1243009-2A-A 5

9

6

6

8

83635

9

8

38

40

37

6

39

9

6

6

8

8

41

42

43

How To Install The

Toilet Brush

Holder

Slide the shaft of the cylinder head(39) of the toilet brush holder kit(38) into the
bonnet(6), orient the cylinder head with the detent facing downward. Tighten the
screw(8) into the bonnet with the hex wrench(9) to secure the toilet brush holder
kit.

Slide the glass holder(40) into the toilet brush holder, then slide the brush (37)
into the glass holder. If necessary, disassemble brush from the toilet brush
holder, then reinstall the brush to the brush holder.

How To Install The Double Towel Shelf

Slide the shaft of the cylinder head(35) of the double towel shelf kit(36) into the
bonnet(6), orient the cylinder head with the detent facing downward. Tighten the
screw(8) into the bonnet with the hex wrench(9) to secure the double towel shelf
kit.

How To Install The Double Towel Bar

Slide the shaft of the cylinder head(42)(43) of the double towel bar kit(41) into
the bonnet(6), orient the cylinder head with the detent facing downward. Tighten
the screw(8) into the bonnet with the hex wrench(9) to secure the double towel
bar kit.

Ensure that all connections are tightened.

Ensure all setscrews face straight down.

INSTALLATION CHECKOUT

All Finishes: Clean the finish with mild soap and warm water. Wipe entire surface completely dry with a clean soft
cloth. Many cleaners may contain chemicals, such as ammonia, chlorine, toilet cleaner etc. Which could adversely
affect the finish and are not recommended for cleaning.

Do not use abrasive cleaners or solvents on Kohler faucets and fittings.

CLEANING INSTRUCTIONS

10

12

6

8

11

8

6

13

9

14

9

6

16

15

8

8

21

17

18

18

19

9

20

23

6

8

24

9

22

9

6

8

25

23

23

6

28

29

27

8

9

8

8

9

6

8

30

31

26

32

How To Install The Covered Toilet Paper Holder

Slide the shaft of the cylinder head(33) of the toilet paper holder kit(34) into the
bonnet(6), orient the cylinder head with the detent facing downward. Tighten the
screw(8) into the bonnet with the hex wrench(9) to secure the toilet paper holder
kit.

6

34

9

33

8

How To Install The Towel Bar

Slide the shaft of the cylinder head(11)(12) of the towel bar kit(10) into the
bonnet(6), orient the cylinder head with the detent facing downward. Tighten the
screw(8) into the bonnet with the hex wrench(9) to secure the towel bar kit.

How To Install The Towel Ring

Slide the shaft of the cylinder head(14) of the towel ring kit(13) into the
bonnet(6), orient the cylinder head with the detent facing downward. Tighten the
screw(8) into the bonnet with the hex wrench(9) to secure the towel ring kit.

How To Install The Glass Shelf

Slide the shaft of the cylinder head(16)(17) of the shelf kit(15)(21) into the
bonnet(6), ensure the brackets are horizontal and two cylinder heads with the
detent facing downward. Tighten the screw(8) into the bonnet with the hex
wrench(9) to secure the shelf kit.

Slide the shelf(19) through the slot on the bracket. Ensure the shelf is in the
center of the slot on the bracket and horizontal. Tighten the setscrew(18) with
the hex wrench(9).

How To Install The TP Holder

Slide the shaft of the cylinder head(22) of the tissue holder kit(24) into the
bonnet(6), orient the cylinder head with the detent facing downward. Tighten the
screw(8) into the bonnet with the hex wrench(9) to secure the tissue holder kit.

Disassemble the tissue spindle(23) from the tissue holder kit(24) as required,
insert roll paper and assemble it back to the tissue holder kit.

How To Install The Robe Hook

Slide the shaft of the cylinder head(26) of the robe hook kit(25) into the bonnet(6),
orient the cylinder head with the detent facing downward. Tighten the screw(8)
into the bonnet with the hex wrench(9) to secure the robe hook kit.

How To Install The Dual TP Holder

Slide the shaft of the cylinder head of the tissue holder kit(27)(28)(29) into the
bonnet(6), orient the cylinder head with the detent facing downward. Tighten the
screw(8) into the bonnet with the hex wrench(9) to secure the dual tissue holder
kit. Disassemble the tissue spindle(23) from the tissue holder kit as required,
insert roll paper and assemble it back to the dual tissue holder kit.

How To Install The Soap Dish

Slide the shaft of the cylinder head(32) of the soap dish kit(30) into the
bonnet(6), orient the cylinder head with the detent facing downward. Tighten the
screw(8) into the bonnet with the hex wrench(9) to secure the soap dish kit.
Insert the dish(31).