Kogan Yeelight sunflower Quick Manual
Yeelight Sunflower
User manual (English)
1 / 3
Copyright © yeelight.com 2012-2014
Ver: SF-1
Yeelight sunflower is a wireless, smart, scene lighting system. It can be installed into your home Wi-Fi network,
and all the bulbs form a system with control box automatically. You may control the bulb to change their color
and brightness with smart device such as smart phone or pad, also you may save the setting to a scene and recall
it at next time. Now the app supports iOS version 5.0+ and Android 2.3.3+.
1. Starter pack
For the starter pack, there are 3 yeelight bulbs and 1 control box; it is the base lighting system.
1) The bulb
The yeelight sunflower bulb is a LED lighting bulb, in which there is a wireless sending/receiving component
working via Zigbee signals. The bulb receives signals from control box and changes color and brightness to what
you want.
2) Control box
The control box is a LAN (local area network) to Zigbee bridge, which transforms the smart phone control
commands (Wi-Fi signals) to Zigbee signals. The Control box has one LAN socket, with which it can be connected
to your home Wi-Fi AP. When it boots up, an IP address will be assigned and your smart phone can search and
connect to it via Wi-Fi. The following figure shows the interfaces on control box.
2. Single pack
For the single pack, there is only one yeelight bulb in the package. The single pack cannot be used independently,
and it should be used to extend bulb number for a starter pack. Please refer to Extra bulb via single pack in
Installation section on how to extend.
LED inside
Wireless antennae area
Cap
Light diffusing dome
Wireless indicator
LAN indicator
LAN interface
Power interface
Button
Introduction
Yeelight Sunflower
User manual (English)
2 / 3
Copyright © yeelight.com 2012-2014
Ver: SF-1
After you install all the components and system is running, a wireless binding between the bulb and control box
is created. In this manual, there are also operations for you to unbind them.
1. Preparation
1) There is a home Wi-Fi AP and your smart phone can connect to it;
2) Check the accessories, including LAN cable and a USB power cable.
2. Starter pack
1) Plug LAN cable into LAN interface of your Wi-Fi AP, and plug another end into control box;
2) Plug in the power cable.
The LAN indicator on control box will fast flash for several times during network configuration, then slow flash for
several times during booting. When it boots up, the LAN indicator is always on. During your control from smart
phone, it will flash 3 times when it gets a command.
3) Screw the bulb into mount base, then turn on the power.
When bulb is turned on, and it transmits messages with control box, the wireless indicator on control box will
show on.
3. Extra bulb via single pack
Screw the bulb into mount base, then turn on the power. Refresh the list on smart phone, it will show new
discovered bulbs.
If you have problems when install extra bulbs, especially when you get them from other control, try to restore
bulb to factory setting, or put them closer to control box to get better wireless signal. About restoring to factory
setting, see the operation in advanced operation section.
4. Advanced operation
1) Restore control box to factory setting
Press down the button on control box and hold it for 10 seconds, then release it, both the LAN indicator and
wireless indicator will fast flash for about 3 seconds. When all the 2 indicator LEDs shows on, the operation is done.
The restore operation will clean the bind info on control box, so the bulb list will be swept, you should reinstall
them. If the bulb is online when you do this operation, it also be restored to factory setting.
2) Restore bulb to factory setting
Keep your bulb on for at least 30s, then turn it off, now you can do the restore operation as following steps:
i) Turn bulb on, when it’s up and shows maximum white light, turn off immediately (less than 5 seconds);
ii) Repeat above step for 3 times;
iii) Then turn on the bulb again, you could see bulb shows red/green/blue/white, it means the
Installation
Loading...