Kogan PRO22 Instruction Manual

High Definition LCD TV / DVD combo

Kogan PRO22

USER MANUAL

Safety information

To ensure reliable and safe operation of this equipment, please read carefully all of the
instructions in this user guide, especially the safety information below.

Electrical safety

·The TV set should only be connected to a mains power supply which matche s that stated
on the label on the mains power adaptor.

·To prevent overload, don’t share the same mains power supply socket with too many
other items of equipment.

·Be careful to route the mains power cable away from areas where people can trip
over it.

·Unplug the TV when it is not going to be used for a long time. Disconnect both the

aerial and the main power cable.

·Take care not to expose the TV set or the remote control to water or moisture.

·Pull the plug out immediately, and seek professional help if:

- the mains power plug or cable is damaged

- liquid is spilt onto the TV set, or if it is accidentally exposed to water or moisture

- anything accidentally penetrates the ventilation slots

- the TV set doesn’t work normally.

·Never remove the cover, there are no user-serviceable parts inside. Allow only
qualified service personnel to repair this equipment.

·To avoid leakage, take out the remote control batteries when:

- the batteries are exhausted

- you are not going to use the remote control for a long time.

·Batteries should be recycled or disposed of in a proper manner.

Physical safety

·Make sure the set is positioned at least 5cm (2inch) from the wall or furniture.

·Never tap or shake the screen for any reason.

·Take care not to drop or sit on the remote control.

·Clean the set using only a soft, clean, dry cloth. Do not use any solvents.

1

OPERATING INSTRUCTIONS

Contents

Safety information--------------------------------------------------------------------------------------- 1

Electrical safety ------------------------------------- ---------------------------------------------------- 1

Physical safety --------------------------------- ------ ------ ---- ------ ------ ---- ------ ---- ------ ------ --- 1
In the box ------------------------------------------------------------ -------------------------------------- 3
Connection ------------------------------------------------------------------------------------------------ 4
Rear connection panel -------------------------------------------------------------------------------- 4
Getting Started ---- ---- -- ---- -- -- ---- -- ---- -- -- ---- -- ---- -- -- ---- -- ---- -- -- ---- -- ---- -- -- ---- -- ---- -- -- --- 5

Front panel controls ------------------------------------------------------------------------------------ 5
The Remote control ------------------------------------------------------------------------------------- 6

Using the remote control for normal TV functions ---------------------------------------------- 6
Initial Setup Instruction Guide ---------------------------------------------------------------------- 8
Power ON/OFF: Standby mode -------------------------------------------------------------------- 8
Selection of Input Mode ------------------------------------------------------------------------------ 8
On Screen Display (OSD) Menu -------------------------------------------------------------------- 9
Navigating the OSD Menu--------------------------------------------------------------------------- 9
Video Page Menu -------------------------------------------------------------------------------------- 10
Audio Page Menu -------------------------------------------------------------------------------------- 13
TV Page Menu (Only for TV) ------------------------------------------------------------------------ 14
Setup Page Menu -------------------------------------------------------------------------------------- 17
Parental Page Menu ---------------------------------------------------------------------------------- 19
DVD Player Operation ----------------------------------------------------------------------------------- 22

Basic Disc Operation------------------- ---- -- ---- -- ---- -- ---- -- ---- -- ---- -- ---- -- ---- -- ---- -- ---- -- ---- 22
Supporting DVD Formats------------------------------------------------------------------------------ 24
DVD Functions Operating Instructions------------------------------------------------------------- 25

MP3 / JPEG / Video File Playback----------------------------------------------------------------- 28
DVD Player Functional Settings Menu------------------------------------------------------------- 29
Menu Navigation---------------------------------------------------------------------------------------- 29

System Setup-------------------------------------------------------------------------------------------- 29
Language Setup---------------------------------------------------------------------------------------- 31
Troubleshooting ------------------------------------------------------------------------------------------ 32
Maintenance ----------------------------------------------------------------------------------------------- 33
Handling Discs--------------------------------------------------------------------------------------------- 34
Features and Specifications-------------------------------------------------------------------------- 35

2

In the box

TV set

Power supply Power supply cable Remote control

- If any of the accessories are missing, then please contact Kogan Technologies.

- Keep all the original packaging in case you need to return the TV to Kogan Technologies.

3

Connection

Rear connection panel

DC

DC

Number Name Function Description

1 HDMI HDMI input jacks (audio and video)
2 VGA VGA (D-sub) comp uter input
3 VGA Audio IN VGA audio input (3.5mm stereo)
4 YPbPr IN YPbPr input
5 AUDIO OUT Audio output for all input sources (3.5mm stereo)
6 S-VIDEO S-Video input
7 CVBS IN AV analogue video input
8 AUDIO L/R Audio signal input for AV/YPbBr/S-Video

9 RF Connect to TV cable/antenna or DVB-t antenna
10 DC Connect to the supplied Power Adaptor
11 USB USB Slot
12 MMC/MS/SD MMC/SD/MS card slot

4

Getting Started

1. Connect the aerial or input source to the appropriate input socket at the rear of
the TV set (see page 4).

2. Connect the small round plug on the power adaptor cable to the power input
socket at the rear of the TV set.

3. Connect the power cable between the power adapto r and the mains supply.

4. Switch the power on by pressing the POWER button on the front panel or the
remote control (the LED will show green).

5. Use the AV/TV button on the front panel or the remote control to select which
input source to use : TV-AV-SVIDEO-YPBPR-VGA-HDMI-DVD

6. You can use the front panel controls to adjust the volume or select a channel as shown
below, or you may use the remote control for these functions.

7. To switch the set off for a short time, press the POWER button, the set will go into
standby and the LED will show red. If you are not going to use the set for some
time, switch the power off completely by unplugging the mains cab le.

Front panel controls

5

The Remote Control

Using the remote control for normal TV functions

1. Insert two AAA batteries, making sure that the polarity is correct as marked
inside the compartment.

2. Aim the remote control at the IR sensor just below the green light (see
page 5 for diagram). Keep this area clear at all times.

3. Do not press the buttons on the remote too quickly – allow the TV time to
respond.

01. POWER :

02. MUTE :

03. DISPLAY: Press to show or remove status display

04. VOL+: Press to increase volume

05. VOL-: Press to decrease volume

06. Numbers: Press to select a channel

07. AV/TV: Press to select input source

08. PMODE: Press to select picture display mode.

09. ENTER: Press to confirm your selection

10. Directions:

11. LCD Menu Press to display the LCD Menu system (see p.9)

12. STOP Press to stop play in DVD mode

13. PLAY/PAUSE Press to start or pause play in DVD mode

14. ANGLE In DVD mode, press to select viewing angles.

14.
SUBTITLE

16. A/E

OSD

17. FAV:
SLOW

18. TIMER: Press to display the time

19. SLEEP: Press to enter Sleep mode, where the TV will

Press to enter or exit the standby mode
Press to turn on or off speaker output

Press
menu screens.

In DVD mode press to skip to the next chapter.
Press to activate subtitles for Digital TV programs
where available.
Press in TV mode to make the current channel a
Favourite
In DVD mode press to display video details
Press to enter the Favourites menu directly
In DVD mode press to toggle slow motion speeds

automatically enter standby mode after a period of
time (toggle between “Off” and between 15 minutes
and up to 240 minutes)

to Select up, down, left, and right in

6

20. GREEN
ZOOM

21. RED

PROGRAM

Press to activate the “GREEN” function in teletext
In DVD mode press to toggle graphic zoom levels.
Press to activate the “RED” function in teletext
In DVD mode press to program playing order

22. EJECT Press to eject a disc from the DVD Player

23. DVD SETUP In DVD mode press to enter the DVD Player
Functional Settings menu (see page 29 for details)

24. CH+ Press to select next TV channel up (see p.15
“Channel Skip”)

25. CH- Press to select next TV channel down (see p.15
“Channel Skip”)

26. DOT Press the number buttons with this to select
channels directly (i.e. channel 108-1 would need
the DOT button pressed after the 8).

27. SMODE Press this button to toggle between preset sound
modes for different echoing effects.

28. EXIT Press this button to exit in a menu.

29.

TEXT

In DVD mode, press to toggle fast forward speeds
Press to enter or exit teletext mode for TV/DVB

30. In DVD mode press to toggle rewind speeds.

31. In DVD mode press to go to previous chapter.

32. REPEAT In DVD mode press to toggle repeat play settings.

33. EPG

LANG

34.

AB

In TV/DVB mode, press to display the Electronic
Programming Guide
In DVD mode press to toggle between audio tracks
Press to access subpages for teletext
In DVD mode press to select A-B section for replay

35. GOTO In DVD mode press to enter track to skip to (p.26)

36. / SIZE

37. YELLOW

MENU

38. BLUE

SUBTITLE

Press to toggle between display aspect ratios.
Press to activate the “YELLOW” function in teletext
In DVD mode press to return to the DVD menu.
Press to activate the “BLUE” function in teletext
In DVD mode press to toggle between subtitles
available.

Note:

- The TV will return to TV mode when any of the buttons for changing channels are used,
i.e. the Number buttons, CH+ and CH-

- A more complete DVD mode button description is available from page 25-27.

7

Initial Setup Instruction Guide

Power ON/OFF: Standby mode

- Press POWER ( ) button on the remote control or on

the side panel to turn on the unit.

[The power indicator changes from red to green]

- Press POWER ( ) button on the remote control or on
the side panel again to return the display to standby mode.

[The power indicator changes from green to red]

Selection of Input Mode

- Press the Input (AV/TV) button to display the signal source menu.

- Press
then press the Enter button to confirm.

When selecting the input source, the screen will display the information
of the selected input source. For example:

TV mode

- When there is no signal from the selected source or channel, a warning message will be displayed.

- If you see the “No Signal!” warning, you can select a different channel or press the Input (AV/TV)
button to change the selected source.

- When you first receive your new TV, it is advisable to perform a new “Channel Scan” to setup your
set to receive all of the channels available in your area. Follow the section “Using Channel Scan”’
on page 15.

or button to select the signal source you desire,

8

On Screen Display (OSD) Menu

After you have installed the batteries in the remote control, you can set setting preferences on
the TV using the OSD menu system.

Navigating the OSD menu:

- The buttons used in the OSD menu include:
’MENU’ (LCD MENU), , ‘ENTER’ and ‘EXIT’.

- Whatever input source is currently selected, press
the Menu button to open the OSD Menu for that source,

then

The sub menu pages are displayed in the following sequence
(circular display):

Video Audio TV Setup Parental

Note: The TV sub menu page will only appear for the TV mode OSD Menu.

When pressing the Menu button on the remote control or on
the side panel, it will change in the following sequence:

Main Menu Press Menu or Exit Exit
Sub Menu Press Exit Previous Menu

1. Press the Menu button to display the menu system.

2. Press

3. Press the Enter or

4. Press or button to select an item.

5. Press

6. If you do not make a selection within several
seconds, the main menu will close automatically,

7. Press the Menu or Exit button exit the OSD menu.

NOTE: The main TV OSD Menu is not accessible when in DVD mode.
The audio and picture settings for DVD mode are the same as for TV, AV
and S-VIDEO mode, so go to one of these first to change DVD mode settings.

or to select the sub menu pages

or button to select the menu pages.

button to enter.

button to select or adjust a setting.

9

On Screen Display (OSD) Functions

Video Page Menu

Adjustment of “Brightness” or “Contrast”

1. Press the Menu button, and the “Video” menu
appears.

2. Press or Enter to enter the “Video” sub menu .

3. Press or to highlight your selection.

4. Press or

5. Press the Menu button to exit the OSD Menu, or
press Exit to select another OSD submenu.

Adjustment of “Saturation” (inactive for VGA)

1. Press the Menu button, and the “Video” menu
appears.

to adjust.

2. Press or Enter to enter the “Video” sub menu .

3. Press or to highlight “Saturation”.

4. Press or

5. Press the Menu button to exit the OSD Menu, or
press Exit to select another OSD submenu.

Adjustment of “Hue” (only for NTSC)

1. Press the Menu button, and the “Video” menu
appears.

2. Press

3. Press or to highlight “Hue”.

4. Press or

5. Press the Menu button to exit the OSD Menu, or
press Exit to select another OSD submenu.

Adjustment of “Sharpness” (inactive for VGA)

1. Press the Menu button, and the “Video” menu

appears.

2. Press or Enter to enter the “Video” sub menu .

3. Press or to highlight “Sharpness”.

4. Press or

5. Press the Menu button to exit the OSD Menu, or
press Exit to select another OSD submenu.

to adjust.

or Enter to enter the “Video” sub menu .

to adjust.

to adjust.

10