Page 1
3 HEADED OUTDOOR SOLAR
MOTION SENSOR LIGHT
NBBR3HOSMSL
Page 2
Page 3
SAFETY & WARNINGS
Ensure to read all instructions and warnings in this user guide prior to first use. Retain this
user guide for future reference.
• Do not install this light near flames or flammable gases.
• Do not install this light near other light sources.
• Keep the light away from children.
• Do not install on an unstable surface or position.
• Do not stare directly at the light while it is on.
• To prevent the unit from falling, ensure the screws and wall plugs used are fully
secured.
• This light is not a crime-prevention measure. Always take reasonable precautions in
securing your home and protecting yourself.
• If the light is damaged, stop use and contact help.Kogan.com for assistance.
Page 4
COMPONENTS
A Motion sensor light (x1)
B 5.8x28mm wall plug (x3) C 3.8x24mm screw (x3) D User guide (x1)
Page 5
Solar panel
COB LED
Rotatable
Sensor
Rotatable
COB LED
Mode button
Detachable
bracket
OVERVIEW
Front view
Back view
arm
arm
Page 6
BEFORE INSTALLATION
Expose the solar panel to sunlight for eight hours to ensure a sufficient charge.
Press the mode button to switch on the light prior to installation.
INSTALLATION
Ensure the light is installed at a height between three and five metres above the ground.
Installing onto a masonry wall
1. Detach the bracket from
the light.
4. Insert the wall plugs into
the drilled holes.
2. Place the bracket on the
wall where you would like
to install the light. Using
a pen (not supplied),
mark the positions of the
three holes of the
bracket.
5. Align the bracket with the
holes. Using a Phillips
screwdriver (not
supplied), secure the
bracket with the screws.
3. Using a drill and 5.8mm
drill bit (not supplied), drill
holes 28mm deep
through the three
marked positions.
6. Attach the light onto the
bracket.
Page 7
Installing onto a non-masonry wall
1. Detach the bracket from
the light.
4. Align the bracket with the
holes. Using a Phillips
screwdriver (not supplied),
secure the bracket with
the screws.
2. Place the bracket on the
wall where you would like
to install the light. Using a
pen (not supplied), mark
the positions of the three
holes of the bracket.
5. Attach the light onto
the bracket.
3. Using a drill (not
supplied), drill pilot holes
through the three
marked positions.
Page 8
OPERATION
Modes
This light features three light modes. Press the mode button to cycle through the three
modes.
In mode 1, the light will illuminate at 100% brightness when people are detected. The light
will then turn off 20 seconds after people leave its vicinity.
In mode 2, the light will illuminate constantly at 10% brightness. It will then illuminate at
100% brightness when people are detected.
In mode 3, the light will illuminate at a constant 30% brightness at night regardless of
whether people are within its vicinity.
Page 9
Angle adjustment
The angle of the LED and solar panels can be adjusted by turning them as seen below.
Page 10
TROUBLESHOOTING
If the light is not illuminating, try the following solutions below:
• Ensure the light is not installed under the shade during the day.
• The solar panel/battery may need to be charged. Ensure the solar panel is located
under direct sunlight, then allow it to charge.
SPECIFICATIONS
Solar panel power 5.5V, 1.8W
Material ABS
Light source COB LED
Battery Built-in 2pcs DC3.7V 1200mAh lithium battery
IP rating IP44
Delay time 20–25 seconds
Number of modes available 3
Detection range 3–7 metres
Brightness 550lm
Colour temperature 6000–6500K
Consumption 10W
Induction angle 120°
Page 11
NOTES
Page 12
Need more information?
We hope that this user guide has given you
the assistance needed for a simple set-up.
For the most up-to-date guide for your product,
as well as any additional assistance you may require,
head online to help.kogan.com
Loading...