Kogan KAVACRBLX8A User Manual

Page 1
KOGAN SMARTERHOME™ LX8 ROBOT VACUUM
WITH MOPPING FUNCTION
KAVACRBLX8A
Page 2
Page 3
Only use the original adaptor, battery and charging station
Before using the product, observe the following safety precautions:
Retain for future reference and pass on these instructions if you give the product to
another person.
Incorrect operation can lead to serious personal injury and damage to the product.
Safety Precautions
Caution
provided or else it will damage the machine. Excess voltage may cause fire or electric shock.
Do not attempt to repair this product yourself. If the product or its power supply experiences any malfunction or damage, stop using it immediately and contact Kogan.com to arrange a repair.
Remove from power before performing maintenance. Do not touch the battery socket and the machine when your
hands are wet or else it will cause electric shock.
Don’t use this product without protective guards in place if it will be in danger of falling.
Do not place clothes or any place of your body (hair, finger, etc.) into the main brush and wheels or it may cause personal injury.
Do not put the machine near fire, inflammable, explosive or corrosive materials.
The machine is only for indoor use.
Page 4
Do not allow water, oil or other liquids to enter the machine.
Ensure the area is clear of wires and other hazards before beginning operation as they may become tangled in the wheels or brushes.
Remove all fragile objects from the area before beginning operation.
Position the charging station against a wall or flat surface to ensure reliable operation.
Switch off the cleaner before removing from the battery.
Disconnect from power if it will not used for a long time.
Do not disconnect the docking station during vacuum operation or it will not return to it to recharge.
Page 5
Do not allow the vacuum to collect glass or other sharp objects.
Do not use the vacuum in humid, flammable, explosive or corrosive environments.
Child Safety
Do not allow children to play with the machine or remain unsupervised while it is in operation.
Discard the plastic packaging so that it does not pose a choking hazard.
Battery
Only use the original battery with the machine: contact Kogan for a replacement.
Switch off the cleaner before removing from the battery.
If the battery leaks, do not touch the liquid: instead wipe it with a dry cloth and take
the battery to a recycling centre.
Take the battery to an approved recycling centre to dispose of it.
Suitable Surfaces
The cleaner is suitable for use on wood floors, tiles and carpets.
Page 6
Side Brush x2
Cleaning Brush x1
HEPA Filter x1
The main body contains the battery, two side brushes and a filter.
Main Body x1 Charging Station x1 Adaptor x1
Quick Start Guide x1 Screwdriver & Screw Kit x2 EVA tape x1
Note:
Page 7
Radar
Top Cover
Front Casing
Dust Bin Release
Sensor
Dust Bin
Control Button
Anti-Drop Sensor
Change Contact
Left/Right Wheels
Main Brush Cover and Clip
Middle Brush
Side Brush
Front Wheel
Front View
Bottom View
Page 8
Side View
Anti-bump Sensor
PSD Along-wall Sensor
Infrared Bump Sensor
Recharge Sensor
Power Indicator
Signal Emission
Charging Plate
Charging Station
of Radar Cover
Page 9
Front View
Filter Stand
Dust Pin
Filter Sponge
HEPA Filte r
Box Stand
Dust-box Cover
Reset Button
ON/OFF Button
Page 10
Adopter Socket
Charging Terminal
Over 0.5m
Over 0.5m
Over 0.5m
Installation of Charging Base
Page 11
Wall Surface
Ground
1. Place the charging base on the flat ground against the wall. Ensure there is no obstacle within the range of 1.5 metres in length and 0.5 metres in width.
Note:
Do not frequently move the charging dock. �If the charging dock’s location is changed, the robot vacuum may lose the layout in memory due to failure in positioning. It will then need to rebuild the layout map.
Map rebuilding may result in information such as no-cleaning areas being lost.
2. Remove the protective strip before use.
Page 12
3. Connect the adapter to the charging station.
Danger! Electric Shock
Charging Base
Main Body
Ensure the unit is correctly
aligned with the charging base contacts.
4. Power on and charging:
If the unit has enough power to turn on, place it within a metre of the charging station and the unit will return.
If it cannot turn on, place the unit directly on the charging station.
5. Paste EVA tape on the Radar cover for protection.
Page 13
CONNECT TO SMARTERHOME™ APP
Install App
Download the “Kogan SmarterHome” app from the Play Store (Android) or App Store (iOS).
Register
If you do not have a Kogan SmarterHome™ account, register or sign in with a verification code sent by SMS.
To register:
1. Tap to enter registration page.
2. The system automatically recognises your country/area. You can also select your country code manually. Enter your email address and tap ‘Next.’
3. Alternatively, you can select ‘Register by mobile number’ and enter the verification code sent to you by SMS.
4. Create a profile on the next page to define your location and room.
Page 14
Set device in pairing mode
When the device is first turned on, it may automatically enter pairing mode (the blue light will be continuously flashing). To turn the device on, remove the dust box and set the ON/OFF switch to ‘ON’. Then reinsert the dust box and press the power button.
If not automatically in pairing mode when powered on, you can manually set the device in pairing mode by long-pressing both Power and Home buttons at the same time for more than 3 seconds until both lights begin flashing slowly.
Using AP Mode to add device
5. Once registered, tap “+” in the upper right corner of the app’s home page to add a new device through the network.
6. Select the product type from the list of options in the app (Cleaning Appliances > Vacuum Cleaners), and then select “Other Mode” from the top-right corner when asked to reset the device.
Page 15
7. Select “AP Mode” for the set-up type.
8. Ensure that the device is in pairing mode, with the light flashing, and tap “Confirm light is slowly flashing”.
9. Enter your Wi-Fi details. It is important that your SmarterHome™ device and the app are connected to the same Wi-Fi network during setup.
Page 16
10. Follow the in-app prompts to continue AP Mode connection, which will pair your
Notes:
Note:
mobile phone to the device’s Wi-Fi hotspot to ensure a connection.
If the Wi-Fi hotspot does not appear on your phone in the list of available networks, your device may not be set in AP Pairing Mode correctly. Try repeating the steps outlined above to ensure your device is ready for connection.
11. The device will commence the pairing process and connect to the app. Ensure your Wi-Fi router, mobile phone, and the SmarterHome™ device are kept close until connection is complete.
12. After successfully being added, you will have the option to rename the device and assign it to a location. It will now be listed on the app’s home page. Tap the device listing to enter its control page.
The device and the app have to use the same Wi-Fi network.
The device is only compatible with 2.4Ghz networks.
Page 17
Having trouble connecting?
The prior steps detail the process for “AP Mode” connection. If that does not work for your connection, we suggest trying it again, and if still no success, attempting the following method for Standard (non-AP Mode) connection.
Add device through network
5. Once registered, tap “+” in the upper right corner of the app’s home page to add a new device through the network.
6. Select the product type from the list of options in the app (Cleaning Appliances > Vacuum Cleaners).
7. Ensure that the device is in pairing mode, with the indicator light flashing, and tap “Confirm light is rapidly flashing”. In Standard mode, it will refer to rapid flashing, not slow flashing.
Page 18
Notes:
The device is only compatible with 2.4Ghz networks.
8. Upon successfully confirming pairing mode, enter your Wi-Fi details. It is important that your SmarterHome™ device and the app are connected to the same Wi-Fi network during setup.
9. The device will commence the pairing process and connect to the app. Ensure your Wi-Fi router, mobile phone, and the SmarterHome™ device are kept close until connection is complete.
10. After successfully being added, you will have the option to rename the device and assign it to a location. It will now be listed on the app’s home page. Tap the device listing to enter its control page.
The device and the app have to use the same Wi-Fi network.
If neither Standard or AP Mode methods are successful, please contact kogan.com for assistance.
Page 19
Kogan SmarterHome™ Controls
Note:
When device is online, it can be controlled.
When device is offline, it displays “Offline” and cannot be remotely
powered on.
Page 20
Light Indicators:
Light Indicators:
Tips:
Sweep/On-off Button:
Short-press: start/pause�
Long press: turn off
1. Press any key while cleaning, recharging or regional cleaning to pause the current task.
2. Press and hold the power and home buttons for 3 seconds to reset Wi-Fi.
1. Blue light: Connected WLAN
2. Bi-colour lights: Not connected WLAN
3. Red light: error
1. Blue light: Connected WLAN
2. Bi-colour lights: Not connected WLAN
3. Red light: error
Page 21
State
Display
Beeping
Initialisation after turning on
Blue light breathing Long beep on startup
Initialisation finished
Blue light on
Two beeps
No Wi-Fi connection after initialisation
Connecting to Wi-Fi
Bi-colour lights on after flash
One beep
Connected to Wi-Fi
Blue light on
Two beeps
Reset Wi-Fi connection
Bi-colour lights flashes slowly
One beep
Start cleaning
Blue/bi-colour lights on after flash
Operation start tone
Pause cleaning
Blue/bi-colour lights on after flash
Resume cleaning
Blue/bi-colour lights on after flash
Operation start tone
Cleaning finished
Blue/bi-colour lights on after flash
Two beeps
Low voltage and start self recharging
Red light on after blue/bi-colour lights flashes
Start searching charging base
Pause self-recharging
Blue/bi-colour lights on after flash
Start charging on the base
Blue/bi-colour lights breathing
Two beeps
Received a command
enough power
Full charged
Blue/bi-colour lights on
Dust bin removed
Red light flashes quickly
One beep
Red light flashes quickly and blue/bi-colour lights on
Recreating map
Blue/bi-colour lights on after flash
One beep
Red light goes out after flashing quickly till shutdown
Starting firmware upgrade
Blue/bi-colour lights flashes quickly
One beep
Firmware upgrade failed
Red light blues after quick flash
1.5 second beep
Blue/bi-colour lights on after quick flash
Locating unit
Blue/bi-colour lights on after flash
Locating music
Bi-colour lights on
Recharge tone
Blue/bi-colour lights flashes slowly Recharge tone
while the machine is being charged and without
Dust bin replaced
Turning off
Firmware upgrade finished
Red light restores after on One beep
One beep
Two beeps
Page 22
Cleaning Charging Connector
Charging Connector
Charging Connector
Turn off the power switch or disconnect the power plug.
Clean the charging connectors monthly with a dry cloth.
Do not use oil for scrubbing.
Removing Dust Bin
The dust bin can be removed by pressing the button on the compartment as illustrated above.
Page 23
Cleaning Dust Bin
1. Remove filter and empty dust.
Note: The dust bin should be cleaned periodically.
3. The dust bin can be washed with running water.
The dust bin should be completely air-dried before reinserting.
4. After cleaning, reassemble the filter in the dust bin and then insert the dust bin into the cleaner.
2. Scrub with the cleaning brush.
Cold air
Hot air
Page 24
Cleaning Main Brush
To d isassemble:
1. Push the clip and lift it upward.
3. Remove the middle brushes and roller.
Cleaning Main Brush and Rubber Brush
1. Clean main and plastic brush with the cleaning brush regularly.
2. Lift the main brush outward.
2. Remove the hair and other entanglements on the main brush regularly.
Page 25
Cleaning Side Brush
1. Use a screwdriver to remove the screws on the side brush.
Cleaning the Wheels
Clean the front, left and right wheels regularly with a clean brush.
Note:
The wheel axle may get twisted by hair and screeds lease clear them out without delay.
2. Remove the side brush, clean hair and other rubbish on and inside the side brush base.
Page 26
Clean the Sensors
Ground mounting sensor
IR Sensor
After cleaning work, use a dry cotton cloth to dry the transparent plate to prevent dust from being accumulated.
Page 27
assistance.
Note:
GOOGLE HOME CONTROL
You will need to have set up a Google Home account prior to linking your Kogan SmarterHome™ device.
Adding “SmarterHome” to the Google Home app
1. From the home page of the Google Home app, select the “+” icon to access the ‘Add
and manage’ page.
2. Select ‘Set up device’, then under the Works with Google banner, select ‘Have something already set up?’
3. Select the search bar and type ‘Smarter Home’ to locate the Kogan SmarterHome™ service.
Page 28
4. Tap ‘Authorise’ to grant Google permission to access the SmarterHome™ app and your devices.
5. From here, you will be prompted to sign into your SmarterHome™ account using either your email or mobile phone number, depending on which method you used to register your account.
Page 29
6. Once connected, the app will display any compatible devices linked to your
Note:
functionality, please use the Kogan SmarterHome™ app.
SmarterHome™ account. From here you can assign them to rooms and set up any routines.
7. Tap on any of the devices to view a list of available commands.
Please note that Google Home can only control the base/core functions of any compatible SmarterHome™ devices. To make full use of this product’s smart
Voice commands for Google
Once connected, the following voice commands will be active for the robot vacuum: “Turn robot vacuum on,” and “Turn vacuum off.” Say “OK Google” or “Hey Google” before each command.
Page 30
Note:
You will need to have set up an Alexa account prior to linking your Kogan SmarterHome™ device.
Adding “SmarterHome” to the Alexa app
1. From the home page of the Alexa app, select the “ ” icon in the top-right and select Skills & Games from the sidebar.
2. Select the search bar and type ‘Smarter Home’ to locate the Kogan SmarterHome™ skill.
Page 31
3. Tap ‘Enable to Use’ to add the Kogan SmarterHome™ skill to Alexa.
4. From here, you will be prompted to sign into your SmarterHome™ account using either your email or mobile phone number, depending on which method you used to register your account.
5. Tap ‘Authorise’ to grant Alexa permission to access the SmarterHome™ app and your devices.
Page 32
6. Once connected, the app will perform a search and display the devices linked to your
Note:
functionality, please use the Kogan SmarterHome™ app.
SmarterHome™ account.
7. When your devices have successfully connected to the Alexa app, you will be able to control your Kogan SmarterHome™ devices via Alexa’s voice commands.
Please note that Google Home can only control the base/core functions of any compatible SmarterHome™ devices. To make full use of this product’s smart
Page 33
Main Body Parameters
Accessories Parameters
Working voltage
14.4V
Adaptor
Rated power
27W
Output voltage
24V
Battery
Lithium battery
Output current
630mA
Battery capacity
3200mAh
Charging station
Charging time
4-5hrs
Input voltage
24V
Working time
60-80min
Work temperature
range
Work humidity range
≤80%RH
Voice
≤68dB
Weight
3.5kg
Specification
Φ335 x 83mm
0°C-45°C
Page 34
Issue
Indication
Solutions
Red light flashes slowly with
beeping
Dust bin full or filter
blocked
Red light flashes with 4
beeps
Check if sensor is covered or
relocate to enclosed area
Unit detects it is in
midair
Anti-drop sensor
activated
Red light flashes slowly with
3 beeps
Check if bottom sensor is blocked
and place unit on ground
Red light flashes slowly with
2 beeps
Front bumper stuck
Red light solid with 4 beeps
Check if machine bumper is loose
Main wheel jammed
Red light solid with beeping
Check if main wheel is tangled
Side brush jammed
Red light solid with 2 beeps.
Check if side brush twisted
Main body stuck
Red light solid with 4 beeps.
Check if main body trapped
Unit on slope
Red light solid with 5 beeps.
Place unit back on solid ground
Ensure charging base is in range
and connect with power adapter
Low battery
Red light solid with a beep.
Charge unit
Check if blower blades are loose or
twisted
Red light solid and beeps
1.5 seconds.
Dust bin disconnected
5 beeps Empty dust bin or change filter
Sensor failure
Red light solid with 2 beeps Place unit on solid ground
Cannot detect walls
Charging base failure Red light solid with 3 beeps.
Blower failure Red light solid with 5 beeps.
Unknown fault
If an issue cannot be resolved, visit help.kogan.com for assistance.
Reattach dust bin
Check if main sensor is blocked
Restart unit
Page 35
Page 36
Need more information?
We hope that this user guide has given you
the assistance needed for a simple set-up.
For the most up-to-date guide for your product,
as well as any additional assistance you may require,
head online to help.kogan.com
Loading...