Page 1
5-IN-1 COMBO SCANNER
KASCNCMB51B
Page 2
Safety & Warnings 3
Components 4
Overview 5
Preparation 7
Before Use 10
Operation 11
Cleaning & Care 19
Troubleshooting 19
2
Page 3
SAFETY & WARNINGS
Ensure to read all instructions and warnings in this user guide prior to first use. Retain this
user guide for future reference.
• Do not use this scanner with wet hands.
• Do not use expose this scanner to water or other liquids.
• Do not expose this scanner to heat sources (for example, stoves, radiators).
• Do not block the openings of the scanner.
• Do not attempt to disassemble the scanner yourself.
• If damaged, stop use immediately and contact help.Kogan.com for assistance.
• Ensure the scanner is unplugged when not in use.
3
Page 4
D Backlight holder
E Photo/card holder
F Card cover
COMPONENTS
A Combo scanner B Slide film holder C Negative film holder
G Video cable H USB cable I Power adapter
J Cleaning brush K User guide
4
Page 5
Photo/card holder slot
Slide slot
SD card slot
Power status
Backlight
holder slot
Power port
TV output port
USB port
Control panel
Display
OVERVIEW
Front view
LED
Back view
5
Page 6
Control panel
Power button
Up/mirror
button
Left/exposure
button
Right/colour button
Down/flip button
OK/capture
button
Mode button
Playback
button
6
Page 7
Note:
scanning.
PREPARATION
Ensure all negative films, slides, film holders, and photos are free of dust and dirt
before inserting them into the scanner, as this may affect the image quality when
Slide film
1. Open the slide film
holder.
Negative film
1. Open the negative film
holder.
To avoid mirror images, follow the serial numbers (from left to right) on the top of the film
when inserting it into the holder.
2. Place the slide film into
the holder.
2. Place the negative film
into the holder.
3. Close the slide film
holder.
3. Close the negative film
holder.
7
Page 8
Photos
1. Remove any film holders from the scanner by sliding them out on the left side. If the
backlight holder is inserted, press down on the handle and pull it out of the scanner.
2. Open the photo/card holder. Aligning with the base of the holder, place your photo
inside. Close the holder.
8
Page 9
Business cards
1. Remove the slide/negative film holders, and backlight holder from the scanner.
2. Open the photo/card holder. Aligning with the guidelines in the centre of the holder,
place the card inside.
3. Place the card cover over the photo/card holder, then close the holder.
9
Page 10
BEFORE USE
SD card
This scanner requires an SD card to store saved images.
Insert a FAT formatted SD card (not supplied, maximum 32GB) into the SD card slot.
For slide and negative films:
Insert the slide or negative film into the slide slot.
Insert the backlight holder into the backlight holder slot.
For photos and business cards:
Insert the photo/card holder into the photo/card holder slot.
10
Page 11
Indicator
OPERATION
Placement
Place the scanner on a stable, dry, level surface.
Powering on/off
• Plug the ends of the power adapter into the power port on the scanner and a socket.
• Turn the socket on and press the power button to turn on the scanner.
• Press the power button again to turn off the scanner.
Live view mode
When powered, the scanner will show the live view as indicated by the flashing red
indicator. This gives a plain view of the media inserted and allows for the following
adjustments:
• Flipping
• Mirroring
• Exposure
• Colour balance
Mirroring
To mirror images, press the up/mirror button. Press the OK/capture button to save and exit.
11
Page 12
Flipping
Flipping may be needed if film is placed upside down. To flip images, press the down/flip
button. Press the OK/capture button to save and exit.
Exposure
The exposure can be adjusted with a range between –3 to 3.
1. Press the left/exposure button.
2. Press the up/mirror and down/flip buttons to adjust the exposure.
3. Press the OK/capture button to save and exit.
12
Page 13
Colour balance
The RGB levels can be adjusted with a range between –3 to 3.
1. Press the right/colour button.
2. Press the up/mirror and down/flip buttons to adjust the level of redness.
3. Press the left/exposure and right/colour buttons to switch between adjusting the red,
green, and blue levels.
4. Press the OK/capture button to save and exit.
13
Page 14
Settings mode
TV
output
USB mode
Media type
Power saving mode
Reformat
SD card
Photo
B&W negative
film
Slide film
Negative film
Business
card
From the live view mode, press the mode button to enter the settings mode. Various
settings can be adjusted.
Media type
This is used to select the type of media inserted (negative film, slide film, B&W negative
film, photo, card). This setting must be changed to match what has been inserted. The
scanner will select negative film as default. To change the media type:
1. Press the OK/capture button. This will open a sub-menu displaying the different
media types available.
2. Use the left/exposure and right/colour buttons to navigate over the media types.
3. Press the OK/capture button to confirm.
14
Page 15
Scanning slide and negative films
1. Ensure the slide or negative film is inserted fully into the correct film holder and
placed into the slide slot. Insert the backlight holder into the scanner.
2. Press the power button to turn on the scanner, then press the mode button.
3. Ensure the media type set matches that inserted into the scanner. Press the
OK/capture button to scan.
You may either press the playback button or press the power button to turn off the
scanner and remove the SD card to view scanned images. The images can also be
transferred to a PC using USB mode.
Scanning photos and business cards
1. Ensure the photo/card holder is fully inserted. Ensure the slide/negative film holders,
and backlight holder are removed. Press the power button to turn on the scanner,
then press the mode button.
2. Ensure the media type set matches that inserted into the scanner. Press the
OK/capture button to scan.
Reformat SD card
The SD card used must be in the FAT format. If the SD card needs to be reformatted:
1. In the settings mode, use the left/exposure and right/colour buttons to navigate to
the SD card format icon. Press the OK/capture button to select. This will open a
sub-menu to confirm reformatting.
2. Use the left/exposure and right/colour buttons to navigate to the ticked checkbox
icon and press the OK/capture button to confirm.
15
Page 16
USB mode
Selected
image
Cancel
Rotate 90°
clockwise
Save
Rotate 90°
anti-clockwise
This mode allows the scanner to transfer saved/scanned images on the SD card into a PC.
1. Connect the USB cable into the USB port on the scanner and your PC.
2. In the settings mode, use the left/exposure and right/colour buttons to navigate to
the USB mode icon. Press the OK/capture button to select. The display will show a
USB icon confirming this mode.
3. Transfer the images from the SD card to the PC.
TV output
Using this function allows your TV to be used as the display
instead of the scanner.
1. Connect the black connector of the video cable into the TV
output port on the rear of the scanner. Connect the yellow
connector of the cable into your TV.
2. In the settings mode, use the left/exposure and right/colour
buttons to navigate to the TV output icon. Press the
OK/capture button to select. This will open a
sub-menu.
3. Use the left/exposure and right/colour buttons to navigate
to ‘PAL’, then press the OK/capture button to select. The
TV will now act as the display for the scanner.
Power saving mode
Activating this mode will turn off the scanner after three minutes of non-use.
• In the settings mode, use the left/exposure and right/colour buttons to navigate to
the power saving mode icon. Press the OK/capture button to activate the mode. The
scanner will display the power-saving mode icon when activated.
Capture mode
When in live view mode, press the OK/capture button and wait for 2–3 seconds to select an
image and enter capture mode. In this mode, the image on the display can be saved and
rotated.
16
Page 17
Rotating
Note:
Indicator
1. Use the left/exposure and right/colour buttons to highlight the rotate 90° clockwise/
anti-clockwise icons.
2. Press the OK/capture button to select either icon to rotate the image clockwise/
anti-clockwise.
3. Once rotated as desired, use the left/exposure button to highlight the save icon.
Press the OK/capture button to save the image. The scanner will then return to the
live view.
If you do not want to save the image, use the left/exposure and right/colour
buttons to highlight the cancel icon. Press the OK/capture button to cancel and
return to the live view.
Full SD card
Once the SD card is full, a full icon will appear on the
display and no additional images can be saved. To
continue capturing and saving images, there are two
methods:
• Transfer the saved images into a PC using USB mode.
• Turn off the scanner and remove the SD card. Replace
with a different SD card.
Playback mode
In this mode, you can view, rotate, and delete
saved images. Press the playback button to
enter this mode.
• Once entered, the scanner will enter an
automatic slideshow transitioning every
two seconds to show all saved images.
This is indicated by the indicator in the top
left corner.
• Press the playback button again to return to the live view.
Pausing and manual control of the slideshow
• To pause the slideshow, press the mode or OK/capture button. This will allow for
manual control of the slideshow. Press the left/exposure and right/colour buttons to
view saved images.
• To return to the automatic slideshow, press the OK/capture button.
17
Page 18
Rotating and deleting
Rotate 90°
clockwise
Rotate 90°
anti-clockwise
When in manual control of the slideshow, press the mode button to open a menu that
allows saved images to be rotated and deleted.
• Use the left/exposure and right/colour buttons to highlight the rotate 90° clockwise/
anti-clockwise icons.
• Press the OK/capture button to select either icon to rotate the image clockwise/
anti-clockwise.
• To delete an image, use the left/exposure and right/colour buttons to highlight the
delete icon. Press the OK/capture button to confirm.
Delete
• After rotating or deleting, the scanner will then return to the manually controlled
slideshow. To rotate or delete other images, press the mode button again and repeat
the steps as necessary.
• If there are no images stored on the SD card/all have been deleted, the display will
show as below for two seconds before returning to the live view.
18
Page 19
CLEANING & CARE
Locked
icon
SD card
TROUBLESHOOTING
Ensure the scanner is turned off and unplugged before cleaning.
• Use a clean, dry, non-alcohol cotton swab or an additive-free lens tissue to clean the
glass surfaces on the backlight holder and card cover. This should be performed
periodically to produce clear images.
• Use the cleaning brush to clean the film holders.
• Wipe the exterior with a soft, dry cloth.
Storage
Store the scanner is a cool, dry place.
The SD card is locked.
When locked, the scanner will show the
locked icon and will be unable to scan or
save photos. The SD card will need to be
unlocked.
1. Turn the scanner off and remove the
SD card.
2. Slide the lock switch on the side of
the SD card into the unlocked
position.
3. Reinsert the SD card into the SD
card slot and turn on the scanner to
resume use.
There is an error on the SD card.
If the display shows the SD card error icon,
the scanner is unable to detect a working or
compatible SD card.
• Format the SD card or remove and
replace the SD card (maximum
32GB).
error icon
19
Page 20
Need more information?
We hope that this user guide has given you
the assistance needed for a simple set-up.
For the most up-to-date guide for your product,
as well as any additional assistance you may require,
head online to help.kogan.com
20
Loading...