Kogan KAMN24QUCMA User Manual

USB-C QHD FREESYNC 75Hz
MONITOR (2560 x 1440)

KAMN24QUCMA

SAFETY & WARNINGS

• Read all instructions before using the appliance and retain for reference.

• Unplug the monitor before cleaning it.

• Use a clean, slightly-dampened cloth to wipe the main monitor body.

• To clean the screen: turn it off, unplug it and wait for it to cool completely, then

wipe it with a dry microfibre cloth.

• Do not use cleaning alcohol, ammonia-based liquids or other harsh cleaners.

• This monitor is designed with ventilation holes on the back of the casing. Do not

cover or block them.

• Do not insert any object or spray any liquid into the vents.

• Avoid placing the monitor near heaters, stoves, fireplaces or other sources of heat,

as well as in rooms lacking adequate ventilation.

• Do not position the monitor in unsafe locations. If the monitor falls, it may be
damaged and may injure nearby people.

• Unplug the monitor if it is not going to be used for an extended period.

• Do not place heavy objects on the monitor, its power cord or any connected cable.

• Do not open the back panel of the monitor, as it contains a high-voltage current

even when not plugged in.

LED monitor

Stand Base Quick Start Guide

HDMI cable Power Cable Adapter

OVERVIEW

1. Menu/Enter

2. Volume/Down

3. Brightness/Up

4. Input select/Exit

5. Power On/Off

6. LED indicator

Controls

1. HDMI

2. DisplayPort

3. USB-C

4. USB1

5. USB2

6. EARPHONE

7. Power input (DC 24V)

Ports

Installing the Stand Base

1. Clear a table and place a piece of soft cloth on it to prevent the LED monitor from
being scratched.

2. Lay the LED monitor flat on the table with the LED screen facing down.

3. Insert stand into the monitor, then secure the base by turning clockwise as below.

4. Stand the LED monitor up.

Disconnecting the Stand Base

1. Clear a table and place a piece of soft cloth on it to prevent the LED monitor from
being scratched.

2. Lay the LED monitor flat on the table with the LED screen facing down.

3. Press the release button and pull away the monitor to remove the stand from the
monitor.

4. Pull the release lever and turn anticlockwise to remove the base from stand. Press
the release button.

VESA MOUNT

Follow the steps below to install onto a monitor arm or wall mount (not included)

1. Place the mounting plate onto the back of the LED monitor, lining up the holes of
the plate with the holes in the back of the monitor.

2. Insert the 4 screws into the holes and tighten.

3. Assemble the mount as per the instructions provided with the mount.

4. Connect the power and display cables to the monitor.

Note:

100 x 100mm VESA high hole (n=4), M4, pitch=0.7mm, screw mounting kit
not included.

100mm

100mm

Before using the LED monitor

• Connect external equipment properly.

• Insert the power plug: the power LED indicator will glow orange,without signal

input.

Setup

1. Connect the HDMI, DP or USB Type-C cable from your monitor to the computer.

2. Connect the adapter to a properly grounded AC outlet, then to the monitor.

3. Power ON the computer and then power ON the monitor.

4. Set the timing mode on your computer. Recommended resolution and refresh rate
are 2560x1440 @75Hz.

USB-C Connection

This monitor supports the following simultaneous connections via USB Type-C:

• Display via DisplayPort™ 1.2 alternate mode

• Data via USB 3.1

• Power delivery (20V/3.25A, 15V/3A, 9V/3A, 5V/3A)

NOTE: Type-C is not supported on versions of Windows prior to Windows 10.

USB-C Setup

1. Connect the USB Type-C cable from your monitor to the computer.

2. Connect the adapter to a properly grounded AC outlet, then to the monitor.

3. Power ON the computer and then power ON the monitor.

4. Set the timing mode on your computer. Recommended resolution and refresh rate
are 2560 x 1440 @60Hz.

Power ON/OFF

• Press the power button on the front of the monitor: the power LED indicator light
will be blue when the LED monitor is on.

Displays main menu

Enter OSD menu

Select the desired item when in OSD menu

When not in the OSD menu, directly enters Volume Menu

Select the desired item when in OSD menu

When not in the OSD menu, directly enters Brightness Menu

Using the OSD menu

• Use OSD menus to adjust settings by using the menu button on the front of the
LED monitor.

Selects between HDMI, DP and USB-C. Exit OSD menu

Picture

Brightness

0–100

Contrast

0–100

Sharpness

0–4

Aspect Ratio

Between Full /16:9 / 4:3 / 5:4 / 1:1

Ultra Vivid

Off / Low / Middle / High

DCR (Dynamic Contrast Ratio)

On / Off

Parameter Range/Options

Colour

Colour Effect

Standard / FPS / RAC / RTS / Movie

Saturation

0–100

Gamma

Off / 1.8 / 2.0 / 2.2 / 2.4

Temperature

6500 / 5400 / User / 9300

R: 0-255

B: 0-255

Parameter Range/Options

User mode colour adjustments

G: 0-255

Advanced

Volume

0–100

Mute

On / Off

Overdrive

On / Off

Adaptive Sync

On / Off

Blue Light Reduction

Off / Low / Middle / High

Parameter Range/Options

OSD

English / French / Deutsch / Italian / Spanish /
Russian / Dutch / Portuguese

Menu Timeout

10–60 seconds

OSD H/V Position

0–100 (H = horizontal, V = vertical)

Transparency

0–100 (0 = solid, 100 = transparent)

Reset

Restore factory defaults

Parameter Range/Options

Language

Panel

23.8"

Normal, <22W (Typical), <105W(Maximum)

Off Mode: <0.5W

Displayable resolution

2560x1440

Pixel dimension

0.2058 (H) x 0.2058 (V)mm

Display colour

16.7M

Tilt

-4.5–13.5

Active display area

526.85(H) x 296.35(V)mm

Operating: 5° ~ 40°

Storage: -20° ~ 60°

Power

DC 24V 5A

Power management

Temperature

Standby mode: <0.5W

Need more information?

This is a Quick Start Guide and we hope that this

has given you the assistance needed for a simple set-up.

For the most up-to-date guide for your product,

as well as any additional assistance you may require,

head online to help.kogan.com