Kogan KALED55UHDZB User Manual

Important Safety Instructions and Maintenance

Important Safety Instructions

CAUTION

Risk of electric shock, do not open.
Do not attempt to service this product yourself
as opening or removing covers may expose
you to dangerous voltage or other hazards.
Refer all servicing to

Kogan

service personnel.

If the following problems occur:
Turn off the TV set and unplug the AC power cord
immediately if any of the following problems occur.
Ask your dealer or service centre to have it checked
by qualified service personnel
When:

- AC power cord is damaged.

- Poor fitting of AC power outlet.

- TV set is damaged by being dropped, hit or having something thrown at it.

- Any liquid or solid object falls through openings in the cabinet.

To reduce the risk of fire or electric shock, do not
expose this product to rain or moisture.
The apparatus shall not be exposed to dripping
or splashing and no objects filled with liquids,
such as vases, shall be placed on the apparatus.

The screen and cabinet get warm when the TV
is in use. This is not a malfunction.In case of
smoke, strange noise or strange smell from the
unit:

· Turn off the power switch immediately;

· Disconnect the power plug from the power
outlet;

· Contact the Kogan customer service centre. Never attempt to make repairs
yourself because this could be dangerous.

Never push objects of any kind into the set
through the cabinet slots as they may touch
dangerous voltage points or short-circuit parts that
could result in a fire or electric shock. Never spill
liquid of any kind on the set. Use special caution
in households where children are present. The apparatus is not suitable for children
under 3-year to operate.

Do not overload wall outlets, extension cords or
adaptors beyond their capacity, this can result in
fire or electrical shock.
Power-supply cords should be routed so that they
are not likely to be walked on or pinched by items
placed upon or against them, paying particular attention to cords at plug end, adaptors
and the point where they exit from the appliance. The mains plug is used as the
disconnect device. It shall remain readily accessible and should not be obstructed
during intended use. Make sure to plug the power cord in until it is firmly inserted.
When removing the power cord, make sure to hold the power plug when pulling the
plug from the outlet, do not pull the plug out by the wire. NEVER touch the plug or
power cord with wet hands. To disconnect the apparatus from the mains power, the
plug must be pulled out from the mains socket, therefore make sure the mains plug
is always easily accessible.

High Voltage
Do not open

1

Important Safety Instructions and Maintenance

Important Safety Instructions

Do not push or scratch the front filter, or place any objects on top of the TV set. The
image may be uneven or the screen may be damaged.

To avoid the fire, no naked flame sources,
such as lighted candles, should be placed on the
apparatus.

An outside antenna system should not be located in
the vicinity of overhead power lines or other electric
light or power circuits, or where it can fall into such
power lines or circuits. When installing an outside
antenna system, extreme care should be taken to keep
from touching such power lines or circuits as contact
with them might be fatal. Ensure the television is not
overhanging the edge of the supporting furniture.

When not in use

If you will not be using the TV set for several days, the
TV set should be disconnected from the AC mains for
environmental and safety reasons. As the TV set is not
disconnected from the AC power when the TV is turned
off at the standby switch, pull the plug from the AC power
outlet to disconnect the TV completely. However, some
TV sets may have features that require the TV set to be
left in standby to function correctly. In the case of lightning,
unplug the TV set from the outlet immediately. Never
touch the antenna cable during lightning.

Installation

Do not pull the plug out by the cord;
Never touch the plug with wet hands.

Excessive from earphones and headphones
can cause hearing loss.

The ventilation should not be impeded by covering the
ventilation opening with items, such as newspapers,
tablecloths, curtains, etc.
At least 10 cm space should be left around the
apparatus for sufficient ventilation.

The product should be situated away from heat
sources such as radiators, heat registers, stoves, or
other products (including amplifiers) that produce heat.
Place the apparatus in such a position that the screen
is not exposed to direct sunlight. It is best to have soft
indirect lighting while watching and avoid
dark environments
these may cause eye fatigue.
Keep the TV set away from any equipment emitting
electromagnetic radiation.

volume

completely

and reflection from the screen as

2

Important Safety Instructions and Maintenance

Installation

Do not place the set on an unstable cart, stand, table
or shelf. The set may fall, causing serious personal
injury as well as damage to the product. Use only with
the cart, stand, tripod, bracket, or table specified by
the manufacturer, or sold with the apparatus. An
appliance and cart combination should be moved with
care. Quick stops, excessive force, and uneven
surfaces may cause the appliance and cart
combination to overturn.

Do not place this apparatus near water, for example,
near a bath tub, wash bowl, kitchen sink, or laundry
tub; in a wet basement; or a swimming pool; and
the like;

When the TV being moved in from cold location, it

Move

LED Screen
Although the LED screen is made with high precision technology and 99.99% or
more of the pixels are effective, black dots may appear or bright points of light (red,
blue or green) may appear constantly on the LED screen. This is a structural property
of the LED screen and is not a malfunction.
If the surface of the LED panel cracks, do not touch it until you have unplugged the
AC power cord, otherwise electric shock may result.
Do not throw anything at the TV set. The LED panel may break from the impact and
cause serious injury.

Precautions When Displaying a Still Image
A still image may cause permanent damage to the TV screen.
Do not display still images and partially still images on the LED panel for more
than 2 hours as it can cause screen image retention. This image retention is
also known as "screen burn". To avoid such image retention, reduce the
degree of brightness and contrast of the screen when displaying a still image.
Watching the LED TV in 4:3 format for a long period of time may leave traces
of borders displayed on the left, right and centre of the screen caused by the
difference of light emission on the screen. Playing a DVD or a game console
may cause a similar effect to the screen. Damages caused by the above effect
are not covered by the Warranty.
Displaying still images from Video games and PC for longer than a certain
period of time may produce partial after-images. To prevent this effect, reduce
the 'brightness' and 'contrast' when displaying still images.

Cleaning

Cleaning and handling the screen
surface and cabinet. Disconnect
the unit from the AC outlet before
cleaning. To remove dust, wipe
gently with a soft, lint free cloth. If
required use a slightly damp cloth.

thinner

solvent

needs time for condensation inside the unit to
evaporate fully before turn on the unit;

To prevent injury, this apparatus must be securely
attached to the floor/wall in accordance with the
installation instructions.

MAINS PLUG

Wipe the mains plug with
a dry cloth at regular
intervals. Moisture and
dust may lead to fire or
electrical shock.

Use care not to subject the TV's surfaces to detergent.
(A liquid inside the TV could lead to product failure, fire or
electrical shock.)
Use care not to subject surfaces to bug repellent, solvent,
thinner, or other volatile substances as this may deteriorate the
surface and finish of the cabinet.

3

Important Information

Keep small accessories out of reach of children so they are not mistakenly swallowed.

Table of Contents

4

HOME

Remote Control

3D Glasses

Note: Detail operation please refer to HELP menu on the TV.

Introduction

Features

l TV adopts 55" TFT display screen
l Zero X radiation complies to green environment protection requirement
l Connect to computer directly to create a TV/monitor combo.
l MHL2.0
l Android4.2
l USB3.0
l 16:9 wide screen
l Auto tuning and fine tuning
l HDMI input
l Component Compatible (480i; 480P; 576i; 576P; 720P; 1080i; 1080P)
l PC VGA
l Programmable sleep timer
l Wide range voltage input
l No-signal automatic power off

Input terminals used for external equipment connection

1 x ANTENNA jack 4 x HDMI inputs
1 x computer PC-RGB input 3 x USB inputs
1 x COMPONENT input
1 x AV input 1 x SPDIF output
1 x Headphone output

LED

1 x CVBS output

6

Introduction

Specifications

Model

Display size

LED panel resolution

Speaker output power

Power supply

TV receive system

Frequency range

Video in

Power consumption

Standby consumption

Antenna Input

Controller power

KAL ED55U HDZB

55” Diagonal (max.)

3840X2160

³5 X2W

~110-240V, 50/60Hz

Analog: Antenna:

46.25MHz-855.25MHz
Digital:5-12, 21-69

120W

<1W

75 ohms, unbalanced

1231. 2X315X764.5mm

26.54Kg

22.91Kg

o o

0 C -4 0 C

Note:

- Design and specifications are subject to change without notice.

- Weight and Dimensions shown are approximate.

- It is suggested to watch 3D program under the operation temperature above 10 C to
obtain the best 3D effect.

7

o

Stand and wall-mounting instructions (optional)

How to assemble the stand

If you need to remove or assemble the stand please read the following instructions.

-Before attaching/detaching the stand, make sure to turn off the TV.

-Before performing work, spread cushioning over the base area to lay the LED TV on.
This will prevent it from being damaged.
Assembling instruction(Normal Stand):

1) Fix the bracket and the stand with four screws .(figure 1)

2) Put the television on the table, fix the stand and the unit with screws given in the carton.
(Figure 2)

- To disconnect the stand from the TV, perform the above steps in reverse order.

Bracket

Stand

Figure 1

Screw
B-ST4*20x4

B- ST4 *20

B-M4*10

Figure 2

Screw
B-M4*10x5

8

Stand and wall-mounting instructions (optional)

9

9

General Description

Overview of back panel

HDMI3 HDMI2

HDMI1(MHL)

VGA AUDIO ANT

VIDEO

MIC

SPDIF

L

R

Headphone

Microphone

SPDIF

Camcorder

DVD player

PC (HDMI-output)

PC

Blu-ray disc player

DVD player

10

Pr

Pb

Y/V

HDMI4(4K2K)

TF

USB 3 (3.0)

USB 2

USB 1

HDMI4(4K2K)

TF card

USB 3

(USB 3.0)

USB 2

USB 1

General Description

INPUT

MENU

PROG

VOL

Overview of front panel

The buttons on the lower-left panel control your TV’s basic features, including the on-screen
menu. To use the more advanced features, you must use the remote control.

1

Power Switch

2

Remote Control
Sensor
Power Indicator No light: In power on mode.
White: In standby mode.

Press this button to turn TV on or off.

Aim the remote control towards this spot on the TV.

3

INPUT

4

MENU

PROGr/s

5

6

VOLv/w

7

Standby button

Toggles between all the available input sources.

Press to display an on-screen menu of your TV's features.

Press to change programs.

Press to increase or decrease the volume.

Press button to toggle between normal and standby mode.

11

General Description

Overview of Remote Control

1. INPUT: This button is used to switch among
different sources: DTV,ATV, AV,YPbPr,VGA, HDMI1,
HDMI2, HDMI3, HDMI4.
Select a source and press OK button to confirm.

2. POWER: Press this button to switch to standby
mode, and press it again to turn TV on.

3. Digital buttons(0~9): To select channel with
digital buttons.

4. INFO: This button is used to start the "Current
Service Banner" application that provides
information about the current service.

5. RECALL: Switch to the previous program.

6. FREEZE: Press this button to freeze the image.

7.

MENU: Press this button to display main menu or
exit the menu. When you are in the submenu, you
can press it to return the main menu.

8. SLEEP: TV will be switched off automatically at
preset sleep time if you have set sleep timer. Use

HOME

your remote control to set the sleep timer.
Press SLEEP button on the remote control, then
press this button again to set sleep time: off, 10,
20,30, 60,90,120,180, 240 min. Press MENU
button to exit when you have set the sleep timer.
After you have set sleep timer, press SLEEP button
again, you will see the Remaining time.
Notes: The sleep timer you have set will be
cancelled when the TV turns off or if a power
failure occurs.

9. CH.LIST: Press it to show channel list on screen.

10. FAV: Press it to display favorite list.

11.

Arrow buttons: Press these buttons to move

cursor up/down/left/right for menu.

12.

OK/REC LIST: Press this button to display a list
of recorded programs. In main menu and submenu,
it is a validation button.

GUIDE: In DTV source, this button is used to

13.
start the EPG application.

14.

Exit: Exit the menu.

DTV: Switch to DTV mode.

15.

16. 3D/2D: Press this button to display the “3D setting”.

Note:It is suggested to watch 3D program under
the operation temperature above 10 C to
obtain the best 3D effect.

12

General Description

Overview of Remote Control

17. HOME: Press this button to enter the main interface
directly.

18. ASPECT
mode.

19.

VOLr and VOLs: Press these buttons to

adjust TV volume.

20. PROGrand PROGs: Press these buttons to
change channel upward or downward.
In the teletext, these buttons are used to
display the next page and previous page.

21. MUTE: Press this button to shut off sound of the
TV, press again to restore TV sound.

22. Button/Audio Lang: source
is used to set NICAM sound system.
In DTV , the button is used to set the audio
language.

23. Red/Green/Yellow/Blue Command: These four

HOME

buttons are used to request linked buttons with the
current menu/page.

24. Teletext buttons: Detail operation please refer to
"Teletext “ in the next page.

Digital media player control button:

25. Including
play/pause, stop, previous file, next file, backward,
forward, these buttons are used to control in USB
mode.

26. SOUND: This button is used to select the sound
mode.

27. PICTURE: This button is used to adjust the picture
mode.

28. MIX ( ): Teletext buttons for mix function. It is also
used for recording function when TV is on DTV mode.

: Press this button to switch the screen

In ATV , the button

source

13