Risk of electric shock. DO NOT OPEN!
Do not attempt to service the television yourself, as
opening or removing the covers may expose you to
dangerous voltage or other hazards. Refer all servicing to
the Kogan customer support team.
To reduce the risk of fire or electric shock, do not expose this
product to rain or moisture. The television should not be
exposed to dripping or or splashing, and no liquid filled objects
such as vases should be placed on the case.
In the event of smoke, strange noises or a strange smell
from the unit, you should follow these steps:
•Turn o the unit immediately.
•Disconnect the power plug from the power outlet.
•Contact the Kogan customer support team. Never
attempt to make repairs yourself.
Never push objects of any kind into the set through the
cabinet slots as they may touch dangerous voltage
points or short-circuit parts that could result in a fire or
electric shock. Never spill any liquids onto the set. Use
special caution in households where children are
present. The television is not suitable for children under
4 years old to operate.
Power supply cords should be routed safely to prevent
dangers due to damaged cords.
The mains plug is the main disconnect method, so it should
be easily accessible and not be obstructed during use.
To avoid fires, no naked flame sources such as lit candles or
burning incense should be placed onto the casing of the
television.
Do not pull the plug out of a power outlet by pulling on the
power cable. Always grasp the plug and pull.
Never touch the plug with wet hands.
2
Page 4
An outside antenna system should not be located in the
vicinity of overhead power lines or other electric light
or power circuits.
When installing an outside antenna system, extreme
care should be taken to keep from touching such power
lines or circuits, as contact with them may be fatal.
Always turn the set o when it is not being used.
Unplug the television from the power outlet when it
will not be used for a long time or when there is an
electrical storm.
Never touch the antenna cable during a lightning
storm.
Excessive volume from earphones and headphones can
cause permanent hearing loss. Always monitor the volume of
noise from these devices, especially when children are using
them.
Installation
Ventilation should not be impeded or limited by
covering the ventilation slots with items such as
newspapers, tablecloths, curtains etc..
At least 10cm of space should be left around the
apparatus for sucient ventilation.
The television should be situated away from heat
sources such as radiators, heaters, stoves or other
products that product heat.
Place the television in a position where the screen is
not exposed to direct sunlight. It is best to have soft
indirect lighting while watching, and you should
avoid a completely dark viewing environment and
reflections to avoid eye fatigue.
Keep the product away from high magnetic fields
(such as near an amplifier speaker) to avoid aecting
the tint.
3
Page 5
Do not place the television on an unstable table, stand
or shelf. The set may fall, causing serious injury as well
as damage to the television itself.
If moving the television on a cart, move the unit with
care as sudden stops and starts may cause the
television to overturn.
Do not place this television near water, for example
near a bathtub, wash bowl, kitchen sink, laundry tub,
swimming pool or in a damp basement etc..
When moving the television to a warm location from
a cold location, allow some time for any dew or
condensation inside the television to evaporate fully
before you turn the unit on.
To prevent injury, the television must be securely
attached to the floor/wall in accordance to the
supplied installation instructions.
Cleaning
Unplug the television from the power supply before
cleaning. Do not use any liquid cleaners or harsh
chemicals. Use a soft, damp cloth.
4
Page 6
General Description
•Zero X radiation complies to green environment protection requirements
If you need to remove or assemble the stand, please read the following:
•Before attaching/detaching the stand, be sure to turn the TV o.
•Before performing any work, spread cushioning out over the base area to
lay the TV on. This will prevent it from being damaged.
Do not apply any pressure to the screen display area, which may compromise
the integrity of the display. The Kogan warranty does not cover user abuse or
other damage caused by improper installations.
Stand Assembly
1.Place the TV unit face down on a soft, flat
surface (blanket, foam, cloth etc..) to
prevent any damage to the screen.
2. Attach the stand to the bottom of the TV
using the four MB4 x 22mm screws.
MB4 x 22mm
(4 pcs)
Wall Mounting Instructions
We suggest that the TV is mounted with at least 6cm gap to the wall to prevent
cable interference. Before mounting the TV to the wall, the stand must be
removed (if it is in place).
To attach the wall mount to the TV:
1.Remove the TV stand screws.
2. Remove the stand from the TV.
3. Secure the wall mount bracket to the back of
the TV using four large screws. Follow the
installation instructions of the TV mount itself.
NOTES
•The wall mount bracket is not included with the TV.
•Please confirm that your wall has the strength to withstand the weight of
the TV.
•Be careful not to scratch the panel and TV cabinet when you fasten the
screws to the TV.
6
Page 8
Turning the TV On
1.Install the stand and place the TV on a solid surface.
◦Ensure that the TV is place in a position which allows free flow of air.
Do not cover any ventilation openings on the back cover.
◦To prevent unsafe situations, no flame sources such as lit candles
should be place on or near the TV.
◦Avoid heat, direct sunlight and exposure to rain or water.
2. Connect the antenna cable to the ANT IN aerial socket on the back of the
TV set.
3. Remove the battery compartment cover on the remote
control and insert two AA batteries, taking note of the
polarity markings.
4. Plug the TV power cord into a wall power outlet.
5. Turn the TV on by pressing .on the remote control or the POWER
button on the side control panel of the TV.
7
Page 9
External Connections and Controls
ConnectionsSide Controls
#ItemDescription
1CoaxCoax Output
2AV
3YPbPr
4Line Out
HDMI 1
HDMI 2
5
HDMI 3
HDMI 4
6RFAntenna cable connection
7USB
Connect a video and audio output
jack from a DVD or VCR player.
Connect video cables from a
component device.
Output can be connected to an
amplifier or headphones.
Connect HDMI devices to these jacks.
An HDMI cable carries both video
and audio. You do not need to make
a separate audio connection.
Insert a USB storage device to the
USB port of the TV to view photos or
listen to MP3 music.
Connecting to an antenna wall jack
#ItemDescription
1INPUT
2MENUPress to open or close the menu
3VOL +Press to increase volume.
4VOL -Press to decrease volume.
5CH +Press to go to the next channel.
6CH -Press to go to the previous channel.
7POWER
Press to select the input source.
Press VOL+ button to change to the
selected input source.
Press to turn the TV on or o
(standby mode). When the TV is o,
power still flows to it.
To completely cut all power supply to
the TV, unplug the power cord or turn
the wall switch o.
Note: HDMI cables carry both audio
and video. You do not need to use a
separate audio cable.
Connecting Optical Out
Note: Cables are often colour coded so
you can match the colour-coded jacks.
Note: turn the TV and external devices OFF before making connections.
Playing from External devices
1.Turn on the TV and the connected device.
2. Press INPUT to open the input source list, then press ▲▼/ to highlight the
input to which the device has been connected, then press OK to select.
◦Select TV to watch live TV from the RF input.
◦Select HDMI1, HDMI2, HDMI3 or HDMI4 to play from a device
connected to the HDMI1, HDMI2, HDMI3 or HDMI4 inputs.
◦Select Composite to play from a device connected to the COMPOSITE
input.
◦Select Component to play from a device connected to the
COMPONENT input.
9
Page 11
Remote Control
10
Page 12
Getting Started
Important: make sure all relevent equipment is connected properly before
connecting the unit to a wall power socket and turning on the power.
Powering the TV
To turn the power ON or OFF:
•Plug the power cord into a suitable power point, then turn the power on at the outlet.
•Press the POWER/STANDBY button on the right lower side of the back panel (or on the
remote control, making sure to aim it at the sensor at the front of the TV); the indicator
will glow green. Press it again to power o (standby mode), and the indicator will glow
red.
First Use
When you switch on the TV for the first time, the First Time Setup menu will be displayed on the
screen, as illustrated below.
•Language: use the / buttons to select your OSD (on screen display) language, then use
the ▼ button to go to the next item.
•Country: use the ◄/► buttons to select the country you are living in, then use the ▼
button to go to the next item.
•Time Zone: use the ◄/► buttons to select the time zone you are living in, then use the ▼
button to go to the next item.
•Tune Typ e: use the ◄/► buttons to select the type of scan, then use the ▼ button to go
to the next item.
•Press the OK button to begin scanning for stations.
•To exit channel tuning, press the MENU or the EXIT button, then use the ◄/► buttons to
select YES. Select NO to continue tuning.
•When auto-searching is complete, your TV will display the first channel located.
11
Page 13
Menus
The TV set contains dierent settings menus where you can program your preferred settings.
Once you have programmed any settings, the unit will then retain them in memory until you
change them again, even when switching the unit to standby mode. This means you can always
operate the system under the same conditions.
Channel Menu
•Press MENU on the back panel or remote control to display the main menu.
•Press ◄/► to select dierent submenus.
•Press OK to enter the submenu page.
•Press ▲▼/ to select your preferred option.
•Press ◄/► to adjust the values.
•Press MENU to return to the previous menu page.
•Press EXIT to exit the menu page.
Picture Menu (DTV mode)
•Picture Mode: available options: Standard, Mild, Personal, Dynamic.
•Contrast/Brightness/Saturation/Sharpness/Tint: these values can only be adjusted
when the picture mode is in personal mode. Press the / buttons to decrease or increase
the values. Press the ▲▼/ buttons to switch between the settings.
NOTE: Tint can only be adjusted when in NTSC mode. Australia's video standard is PAL.
•Colour Temp: use this to adjust the optimum colour temperature suitable for viewing.
Available options are: Cool, Normal, Warm.
•Noise Reduction: Available options: O, Low, Middle, High, Default.
•Aspect Ratio: Available options: Auto, 16:9, 4:3, Zoom1, Zoom2
•HDMI Mode: Auto, Video, PC
12
Page 14
Sound Menu (DTV Mode)
•Sound mode: Available options: standard, music, movie, sports, personal
•Treble /Bass : use these items to adjust the levels of higher pitched sounds (treble) and
lower-pitched sounds (bass) from 0 to 100.
Note: these values can only be adjusted when the sound mode is set to personal.
•Balance: use this to adjust the audio output from the left and right speakers from
-50 to 50.
•Auto Volume Level: use this to turn auto volume control on and o.
•AD (Audio Description): press OK to enter, then you can switch AD ON or OFF. When
AD is set to ON, you can adjust the volume level.
Note: Audio descriptions for visual representation works only with programs that contain
the related narration information.
•S/PDIF Mode: use this to select the S/PDIF audio output type: O, Auto, PCM.
•Audio Delay: adjust this setting to synchronize the audio and video.
Time Settings
•Press the OK button to enter.
•Press the ▲▼/ buttons to select the desired item.
•Press the ◄/►/ buttons to adjust the values.
Clock: not user adjustable. TV receives time values from the broadcast signal.
Time Zone: used to select the desired time zone.
Sleep Timer: used to adjust the sleep timer. Available options: OFF, 15/30/45/60/90/120/240
minutes.
No Action Auto Sleep: Used to adjust the timer that will turn the TV o after a period of
inactivity. Available options; ON, OFF.
Auto Standby: Used to select the auto-standby duration. Available options: OFF,3H,4H,5H.
OSD Time: Use to select the desired OSD (on-screen display) menu duration.
Available options: 10/15/20/30 seconds.
13
Page 15
Lock Menu
System Lock
•Press OK or ► to enter.
•Input the factory default password "0000" using the numbers on the remote control.
NOTE: if you forget your password, the master password is "4711".
•Press the ◄/► buttons to turn the lock settings ON or OFF.
Set Password
•Press OK or ► to enter.
•Follow the on-screen instructions and input the old password, then the new password.
Channel Lock
•Press the OK or to enter.
•▲▼Press the /buttons to select the channel you want to lock.
•Press the GREEN button repeatedly to lock/unlock the highlighted channel.
Parental Lock
•Use this item to select the desired program rating. Available options: No Block, Block All,
Block G and above, Block PG and above, Block M and above, Block MA and above, Block
AV and above, Block R and above.
Key Lock
•Use this to the turn the keypad on the TV on or o.
System Menu
OSD Language
Use this to select the desired on-screen display language.
TT Language
Use this to select the desired language for teletext display.
(Please note that teletext is not available in Australia anymore)
14
Page 16
Audio Language
Press OK or ►to enter. Then you can select the desired primary and secondary audio language
(only adjustable if there is a signal).
Subtitle Language
Press OK or ► to enter. Then you can select the desired primary and secondary subtitle
languages and turn on/o the hearing impaired function when this mode is on (only adjustable if
there is a signal).
Hearing Impaired
This item is used to set Hearing Impaired function ON or OFF. For hearing impaired users, this
function can assist them to know a certain scene or action through the caption instead of
hearing it.
Note: hearing impaired function works only when you are viewing programs that contain suitable
captions.
PVR File System
Press ◄/► buttons to select the USB drive.
Check PVR File System: press OK to check the health of the USB drive file system.
DTV Manual Scan
Press OK or ► to enter. Enter your password (the factory default
password is "0000").
Press buttons to select the channel, then press OK to search.
Program Edit
Press OK or to enter. Enter your password (the factory default
password is "0000").
•Press ▲▼/ buttons to highlight the desired channel.
•Press the RED button on the remote to delete the highlighted
channel.
•Press the BLUE button on the remote to skip the highlighted
channel.
•Select the channel you wish to move, then press the YELLOW
button to enter move mode. Use the ▲▼/ buttons to select the
preferred position, then press the YELLOW button again to
move the channel.
•Press the FAV button to add the channel to the favourites list.
15
Page 17
Schedule List
Press ▲▼/ to select this option, then press OK to enter. If any programs are scheduled through
the Add menu (pressing YELLOW on the remote control) then the below menu will appear.
•Press ◄/► buttons to switch between Schedule List and Recorded List.
•Press the RED button to delete the highlighted option.
•Press the YELLOW button to enter the add menu page.
•Press the BLUE button to enter the edit menu page.
Signal Information
This is used to display signal details, such as channel number, frequency, quality and strength.
Media Playback
•Insert a USB memory device into the USB port.
•Press the SOURCE button on the back panel or on the remote control to switch the unit
to USB mode. (Alternatively, press the MEDIA button on the remote control to enter USB
mode directly).
•▲Press /▼/◄/► buttons to move the cursor.
•Press the EXIT button to return to the previous menu.
Photos
•Press ◄/► buttons to select Photo in the main menu, then press OK to enter.
•Select the USB drive and press OK. Only photo files can be played in this menu category.
•▲Use /▼/◄/► buttons to select the desired folder or file, then press OK to open them.
Press PLAY to start playing the files.
16
Page 18
Press the RED button on the remote control to access the sub menu functions such as Delete.
When playing photo files:
•Press the DISPLAY button on the remote control to display the on-screen tool bar. Press
▼ button to hide the tool bar.
•Use ◄/► buttons then press OK to select a function such as Previous, Next, Repeat,
Rotate, Zoom In/Out etc.. from the on-screen toolbar.
•Note: you can only rotate a photo when the slideshow is paused.
Music
•Press ◄/► buttons to select Music in the main menu, then press OK to enter music mode.
Select the USB drive, then press OK. Music files can only be played in this menu category.
•▲Use /▼/◄/► buttons to select the desired folder or file, then press OK to open the
folder or file. Press PLAY to start playing the files.
•Press the RED button on the remote control to access sub menu functions such as delete.
When playing music files:
•Press the DISPLAY button on the remote control to display the on-screen toolbar or ▼
button to hide the toolbar.
•Use ◄/► buttons, then press OK to select a function such as Fast Rewind, Previous, Next,
Mute, Repeat etc.. from the on-screen toolbar.
Videos
•Press ◄/► buttons to select Movie in the main menu, then press OK to enter movie
mode. Select the USB drive, then press OK. Movie files can only be played in this menu
category.
•▲Use /▼/◄/► buttons to select the desired folder or file, then press OK to open the
folder or file. Press PLAY to start playing the file.
When playing movie files:
•Press the DISPLAY button on the remote control to display the on-screen toolbar or ▼
button to hide the toolbar.
•Use ◄/► buttons to select your option, then press OK to confirm.
17
Page 19
Text
•Press ◄/► buttons to select Text in the main menu, then press OK to enter text mode.
Select the USB drive, then press OK. Text files can only be viewed in this menu category.
•▲Use /▼/◄/► buttons to select the desired folder or file, then press OK to open the
folder or file. Press PLAY to display the file.
When playing text files:
•Press the ◄◄/►► buttons to display the previous/next page.
•Press the DISPLAY button on the remote control to display the on-screen toolbar. Press
▼ button to hide the toolbar.
•Press ◄/► buttons to select the preferred option, then press the OK button to confirm.
Troubleshooting
If you have any problems with your television, please check the suggested solutions below, as
these issues may be caused by improper adjustment/setup rather than a malfunction with the
unit. If the problem persists, please contact the Kogan customer support team.
ProblemPossible Solution
Poor picture and sound quality•Try a dierent channel
•Adjust the antenna
•Check all connections
No picture or sound in TV status•Try another channel
•Press the TV/AV button
•Make sure TV is plugged in
•Check the antenna connection
No sound, or sound is too low at maximum
volume
No colour, wrong colour or tints•Make sure the program itself is
Picture rolls vertically•Check all connections
Blurred or snowy picture, distorted sound•Check direction, location and
Remote control malfunctions•Replace remote control batteries
•Check the volume settings on any
external speakers connected to your
television
•Adjust the TV volume accordingly
•Check that MUTE hasn't been turned on
broadcast in colour
•Select the picture menu, then adjust the
colour and tint submenus
connections to your antenna
•Issues may be caused by use of an
indoor antenna
•Check battery terminals
•Remote is out of range, move closer to
TV
•Confirm there is no obstructions
between remote and TV
•Make sure power cord is plugged in
Image is not centered on the screen•Adjust the horizontal and vertical
position
18
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.