Kogan KALED423DSMTZB User Manual

Important Safety Instructions and Maintenance

Important Safety Instructions

CAUTION

Risk of electronic shock, do not open. Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.

If the following problems occur: Turn off the TV set and unplug the AC power cord immediately if any of the following problems occur. Ask

the Kogan customer service centre to have it checked by Kogan qualified service technicians when:

- AC power cord is damaged.

- Poor fitting of AC power outlet.

- TV set is damaged by being dropped, hit or having something thrown at it.

- Any liquid or solid object falls through openings into the cabinet.

To reduce the risk of fire or electric shock, do not expose this product to rain or moisture. The apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on the apparatus.

The screen and cabinet get warm when the TV is in use. This is not a malfunction. In the case of smoke, strange noises or strange smells from the unit:

· Turn off the power switch immediately;

· Disconnect the power plug from the power outlet;

· Contact the Kogan customer service centre. Never attempt to make repairs yourself because this could be dangerous.

Never push objects of any kind into the set through the cabinet slots as they may touch dangerous voltage points or short-circuit parts that could result in a fire or electric shock. Never spill liquid of any kind on the set. Use special caution in households where children are present. The apparatus is not suitable for children under 3-year to operate.

Do not overload wall outlets, extension cords or adaptors beyond their capacity, this can result in fire or electrical shock. Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plug end, adaptors and the point where they exit from the appliance. The mains plug is used as the disconnect device. It shall remain readily accessible and should not be obstructed during intended use. Make sure to plug the power cord in until it is firmly inserted. When removing the power cord, make sure to hold the power plug when pulling the plug from the outlet, do not pull the plug out by the wire. NEVER touch the plug or power cord with wet hands. To disconnect the apparatus from the mains power, the plug must be pulled out from the mains socket, therefore make sure the mains plug is always easily accessible.

High Voltage Do not open

Important Safety Instructions and Maintenance

Important Safety Instructions

Do not push or scratch the front filter, or place any objects on top of the TV set. The image may be uneven or the screen may be damaged.

To avoid the fire, no naked flame source, such as lighted candles, should be placed on the apparatus.

An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal. Ensure the television is not overhanging the edge of the supporting furniture.

When not in use

If you will not be using the TV set for several days, the TV set should be disconnected from the AC mains for environmental and safety reasons. As the TV set is not disconnected from the AC power when the TV is turned off at the standby switch, pull the plug from the AC power outlet to disconnect the TV completely. However, some TV sets may have features that require the TV set to be left in standby to function correctly. In the case of lightning,

unplug the TV set from the outlet immediately. Never touch the antenna wire during lightning.

Installation

Do not pull the plug out by the cable; Never touch the plug with wet hands.

Excessive from earphones and headphones volume can cause hearing loss.

The ventilation should not be impeded by covering the ventilation opening with items, such as newspapers, tablecloths, curtains, etc. At least 10cm space should be left around the apparatus for sufficient ventilation.

The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat. Place the apparatus in such a position that the screen is not exposed to direct sunlight. It is best to have soft indirect lighting while watching and avoid completely

dark environments and reflection from the screen as

these may cause eye fatigue. Keep the TV set away from any equipment emitting electromagnetic radiation.

Important Safety Instructions and Maintenance

Installation

Do not place the set on an unstable cart, stand, table or shelf. The set may fall, causing serious personal injury as well as damage to the product. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. An appliance and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the appliance and cart combination to overturn.

Do not place this apparatus near water, for example, near a bath tub, wash bowl, kitchen sink, or laundry tub; in a wet basement; or a swimming pool; and the like;

When moving the TV in from a cold place, it needs

Move

LED Screen Although the LED screen is made with high precision technology and 99.99% or more of the pixels are effective, black dots may appear or bright points of light (red, blue or green) may appear constantly on the LED screen. This is a structural property of the LED screen and is not a malfunction.

If the surface of the LED panel cracks, do not touch it until you have unplugged the AC power cord. Otherwise electric shock may result. Do not throw anything at the TV set. The LED panel may break from the impact and cause serious injury.

Precautions When Displaying a Still Image A still image may cause permanent damage to the TV screen. Do not display still images and partially still images on the LED panel for more than 2 hours as it can cause screen image retention. This image retention is also known as "screen burn". To avoid such image retention, reduce the degree of brightness and contrast of the screen when displaying a still image. Watching the LED TV in 4:3 format for a long period of time may leave traces of borders displayed on the left, right and centre of the screen caused by the difference of light emission on the screen. Playing a DVD or a game console may cause a similar effect to the screen. Damages caused by the above effect are not covered by the Warranty. Displaying still images from Video games and PC for longer than a certain period of time may produce partial after-images. To prevent this effect, reduce the 'brightness' and 'contrast' when displaying still images.

Cleaning

Cleaning and handling the screen surface and cabinet. Disconnect the unit from the AC outlet before cleaning. To remove dust, wipe gently with a soft, lint free cloth. If required use a slightly damp cloth.

thinner

solvent

some time for dew inside unit to evaporate fully before you turn the unit on;

To prevent injury, this apparatus must be securely attached to the floor/wall in accordance with the installation instructions.

MAINS PLUG

Wipe the mains plug with a dry cloth at regular intervals. Moisture and dust may lead to fire or electrical shock.

Use care not to subject the TV's surfaces to detergent. (A liquid inside the TV could lead to product failure, fire or electrical shock.) Use care not to subject surfaces to bug repellent, solvent, thinner, or other volatile substances as this may deteriorate the surface and finish of the cabinet.

Important Information

Keep small accessories out of reach of children so they are not mistakenly swallowed.

Table of Contents

Accessories

Please make sure the following items are included with your LED TV. If any items are

missing, contact your dealer.

User Manual

Not Included

Remote Control

Introduction

Features

 TV adopts 42" TFT display screenLED  Zero X radiation complies to green environment protection requirement  Connect to computer directly to realize TV/monitor combo.  MHL 2.0  Android 4.2  USB3.0  16:9 wide screen  Auto tuning and fine tuning  HDMI input  Component Compatible (480i; 480P; 576i; 576P; 720P; 1080i; 1080P)  PC VGA  Programmable sleep timer  Wide range voltage input  No-signal automatic power off

Input terminals used for external equipment connection

1 x ANTENNA jack 3 x HDMI inputs 1 x computer PC-RGB input 2 x USB inputs 1 x COMPONENT input 1 x CVBS output 1 x AV input 1 x SPDIF output 1 x Headphone output

Introduction

Specifications

Model

Display size

LED panel resolution

Speaker output power

Power supply

TV receive system

Frequency range

Video in

Power consumption

Standby consumption

Antenna Input

Controller power

Work Temperature

KALE D42 3DS MTZB

42” Diagonal (max.)

1920 x 1080

~110-240V, 50/60Hz

Digital: DVB-T Analog: PAL: BG, I, DK, SECAM: BG, D/K

Analog: Antenna:

46.25MHz-855.25MHz Digital:5-12, 21-69

PAL / NTSC / SECAM

90W

<0.5W

75 ohms, unbalanced

DC 3V (Two AAA size batteries)

967x240x623mm

967x62x576mm

12.5Kg

10.1Kg

0°C - 40°C

Note:

- Design and specifications are subject to change without notice.

- Weight and dimensions shown are approximate.

- It is suggested to watch 3D program under the operation temperature above 10 C to

obtain the best 3D effect.

Stand and wall-mounting instructions (optional)

How to assemble the stand

If you need to remove or assemble the stand please read the following instructions.

- Before attaching/detaching the stand, make sure to turn off the TV.

- Before performing work, spread cushioning over the base area to lay the LED TV on. This will prevent it from being damaged.

Assembling instruction:

Put the television on the table, fix the stand and the unit with four screws given in the carton.

B-M4*10

Stand and wall-mounting instructions (optional)

How to mount the LED TV on the wall

1.After detaching the stand, fasten 2 mounting screws into the 2 screw holes on the rear cover, see the figure below.

2.Fasten wall mounting bracket with screws on the wall.

3.Carefully check for the strength before releasing the LED TV. Note: For more detailed instructions please refer to your "after market" wall mounting instruction manual.

Figu re1 Figu re2

2-M6 X8

2-M6 X18

Figu re3

General Description

Overview of back panel

You can connect the TV with video devices such as DVD/VCD player, VCR and video camera

to enjoy the high quality picture.

USB 2

USB 1

Video output

Camcorder

SPDIF

DVD player

PC (HDMI-output)

Blu-ray disc player

Microphone

Headphone

General Description

Overview of front panel

The buttons on the lower-left panel control your TV’s basic features, including the on-screen menu. To use the more advanced features, you must use the remote control.

INPUT

PROG

VOL

MASTER POWER SWITCH Press this button to turn TV on or off. REMOTE CONTROL SENSOR Aim the remote control towards this spot on the TV. POWER INDICATOR ON: In standby mode. OFF:In power on mode. INPUT Toggles between all the available input sources. MENU Press to display an on-screen menu of your TV's features.

PROG/ Press to change programs. In the on-screen menu, use the PROG /buttons as up/down arrow buttons. VOL / Press to increase or decrease the volume. In the on-screen menu, use the VOL/ buttons as left/right arrow buttons.

△

STANDBY BUTTON Press button to toggle between normal and standby mode.

General Description

Overview of Remote Control

1. INPUT: This button is used to switch among different sources: DTV, ATV, AV, YPbPr, VGA, HDMI1, HDMI2, HDMI3. Select a source and press OK button to confirm.

2. POWER: Press this button to switch to standby mode, and press it again to turn TV on.

3. Digital buttons(0~9): To select channel with digital buttons.

4. INFO: This button is used to start the "Current Service Banner" application that provides information about the current service.

5. RECALL: Switch to the previous program.

6. FREEZE: Press this button to freeze the image.

7. MENU: Press this button to display main menu or

exit the menu. When you are in the submenu, you can press it to return the main menu.

8. SLEEP: TV will be switched off automatically at preset sleep time if you have set sleep timer. Use

HOME

your remote control to set the sleep timer. Press SLEEP button on the remote control, then press this button again to set sleep time: off, 10, 20,30, 60,90,120,180, 240 min. Press MENU button to exit when you have set the sleep timer. After you have set sleep timer, press SLEEP button again, you will see the remaining time. Note: The sleep timer you have set will be cancelled when the TV turns off or if a power failure occurs.

9. CH.LIST: Press it to show channel list on screen.

10. FAV: Press it to display favorite list.

11. Arrow buttons: Press these buttons to move

cursor up/down/left/right for menu.

12. OK/REC LIST: Press this button to display a list

of recorded programs. In main menu and submenu, it is a validation button.

13. GUIDE: In DTV source, this button is used to

start the EPG application.

14. Exit: Exit the menu.

15. DTV: Switch to DTV mode.

16. 3D/2D: Press this button to display the “3D setting”.

Note: We suggest you watch 3D programs at an operation temperature above 10 C to obtain the best 3D effect.

General Description

Overview of Remote Control

17. HOME: Press this button to enter the main interface directly.

18. ASPECT: Press this button to switch the screen

mode.

19. VOL and VOL: Press these buttons to

adjust TV volume.

20. PROGand PROG: Press these buttons to change the channel upward or downward. In the teletext, these buttons are used to display the next page and previous page.

21. MUTE: Press this button to shut off sound of the TV, press again to restore TV sound.

22. Button/Audio Lang: sourceIn ATV , the button

is used to set NICAM sound system. In DTV , the button is used to set the audiosource language.

23. Red/Green/Yellow/Blue Command: These four

HOME

buttons are used to request linked buttons with the current menu/page.

24. Teletext buttons: Detail operation please refer to “Teletext” in the next page.

25. IncludingDigital media player control button:

play/pause, stop, previous file, next file, backward, forward, these buttons are used to control in USB mode.

26. SOUND: This button is used to select the sound mode.

27. PICTURE: This button is used to adjust the picture mode.

28. MIX ( ): Teletext buttons for mix function. It is also used for recording function when TV is on DTV mode.

General Description

Teletext

HOME

Teletext is an information system broadcast by certain channels which be consulted like a newspaper. It also offers to subtitles for viewers with hearing problems or who are not familiar with the transmission language. You can press these buttons to operate the teletext: Text Press TEXT button to enter or exit teletext mode. Hold Press HOLD button to toggle Hold function on or off. When Hold is switched on, the page acquisition is stopped. When Hold is switched off, the page acquisition is started. Size

Press SIZE button one time to display the upper

half of the screen in double height, press the SIZE button two times to display the lower half of the screen in double height, press three times to display the full screen in normal size.

Red/Green/Yellow/Blue Command

These four buttons are used for quick access to

different pages as numbered at the bottom of the screen.

Index Press INDEX button, then index page displays. Reveal Pressing this button will reveal any hidden data

(answers to quizzes for example).Press the REVEAL button again to return to normal screen.

General Description

Teletext

HOME

Cancel

The CANCEL button will exit from any Teletext on

the display. Press CANCEL button again to exit Teletext and return to live TV broadcast.

Subtitle Turning the Teletext subtitles on or off. Subtitles is a separate mode with only a few buttons available. There will be no OSD visible other than the Teletext Subtitles. Subcode Subcode mode gives the possibility to select certain subcode pages of a Teletext page. Entry of digits within the range 0...9 for current subcode entry. If the digit completes the entry, a page request is started. Press PROG/PROG buttons to change the subcode pages. Time This button is used to show the time of the Teletext. Digital buttons(0~9) You can press them to enter the number of the Page required. PROG/PROG You can press them to change page upward or downward.

Mix Press MIX button, the teletext page turns

transparent. TV content and teletext page content will display at the same time. Press MIX button again to exit MIX mode.

General Description

Installing Batteries in the Remote Control

Inst al li ng Batt er ie s

Open the battery compartment

cover on the back side.

Insert two 1.5V AAA size batteries in correct polarity. Don ´t m ix o ld o r

used batteries with new ones .

Close the cover.

Poi nt the re mote to wards t he remo te con trol se nsor of t he TV and u se i t wit hin 8 met ers.

Put t he used b atter ies int o the rec yclin g bin sin ce they c an nega tivel y aff ec t th e env ironm ent.

The ba tte rie s (batt ery p ack o r batterie s ins tal led) sh all n ot be e xpo sed to exce ssi ve he at such as sun shi ne, f ire or th e lik e.

External Connection

Antenna connection

Antenna input impedance of this unit is 75ohm. VHF/UHF 75ohm coaxial cable can be connected to the antenna jack directly, if the antenna cable is 300ohm parallel flat feeder cable, you need to use the 300ohm/75ohm converter to connect the antenna cable to the antenna jack. For details Please refer to the following drawing.

Antennas with 300  flat twins Leads

Use a 75ohm - 300ohm converter

ANT IN

300ohm coaxial cable

Antenna feeder

Antennas with 75  Round Leads

75oh m co ax ia l ca bl e

Ante nn a ca bl e

External Connection

Connecting VCR

These instructions assume that you have already connected your TV to an antenna or a cable TV system. Skip step 1 if you have not yet connected to an antenna or a cable system.

VCR Rear Panel

ANT

ANT OUT S-VIDEO

1 2 3

VIDEO OUT

Green

Blue

Red

AUDIO OUT

White

TV Rear Panel

Red

RF Cable (Not supplied)

YPbPr cable( supplied) Not

Audio Cable (Not supplied)

Green

RedBlue

Red

White

Follow the instructions in Viewing a VCR or Camcorder Tape to view your VCR tape. Each VCR has a different back panel configuration. When connecting a VCR, match the color of the connection terminal to the cable.

1. Unplug the cable or antenna from the back of the TV.

2. Connect the cable or antenna to the ANT IN terminal on the back of the VCR.

3. Connect an RF Cable between the ANT OUT terminal on the VCR and the ANT IN terminal on the TV.

4. Connect a Component Cable between the COMPONENT [Y, Pb, Pr] jacks on the DVD

player and YPbPr jack on the TV.

5. Connect Audio Cables between the AUDIO OUT jacks on the VCR and the AUDIO L and AUDIO R jacks on the TV.

Note: 1. Whenever you connect an external device to your TV, make sure that power on the unit is turned off.

2. When connecting an external device, match the color of the connection terminal to the cable.

External Connection

Connecting a Camcorder

The rear panel jacks on your TV make it easy to connect a camcorder to your TV. They allow you to view the camcorder tapes without using a VCR.

Each Camcorder has a different back panel configuration. When connecting a Camcorder or DVD, match the color of the connection terminal to the cable.

1. Connect a Video Cable between the AV VIDEO jacks on the TV

and the VIDEO OUT jack on the camcorder.

2. Connect Audio Cables between the AUDIO L and AUDIO R jacks on the TV and the AUDIO OUT jacks on the camcorder.

3. Connect a Video Cable between the component IN Y on the TV and the VIDEO OUT jack on the DVD.

4. Connect Audio Cables between the component IN AUDIO L and R jacks on the TV and the AUDIO OUT jack on the DVD.

White

Camcorder

Video Cable (Not supplied)

Note:

1. Whenever you connect an external device to your TV, make sure that power on the unit is turned off.

2. When connecting an external device, match the color of the connection terminal to the cable.

Red

Yellow

Audio Cable (Not supplied)

Red

White

External Connection

Connecting DVD Player/Set-Top Box via HDMI

This connection can only be made if there is a HDMI Output connector on the external device.

DVD Player/ Set-Top Box

HDMI Cable (Not supplied)

What is HDMI? HDMI, or high-definition multimedia interface, is a next-generation interface that enables the transmission of digital audio and video signals using a single cable without compression. Multimedia interface is a more accurate name for it especially because it allows multiple channels of digital audio (5.1 channels). The difference between HDMI and DVI is that the HDMI device is smaller in size, has the HDCP (High Bandwidth Digital Copy Protection) coding feature installed, and supports multi-channel digital audio. Each DVD player/STB has a different back panel configuration.

1. Connect an HDMI Cable between the HDMI1, HDMI2, HDMI3 connector on the TV and the HDMI connector on the DVD player/Set-Top Box.

TV Rear Panel

Note:

1.Whenever you connect an external device to your TV, make sure that power on the unit is turned off.

2.When connecting an external device, match the color of the connection terminal to the cable.

External Connection

Connecting Digital Audio System

The rear panel jacks on your TV make it easy to connect a Digital Audio System to your TV.

Digital Audio System

TV Rear Panel

(Bla ck )

Coaxial Cable (Not supplied)

5.1 CH audio is possible when the TV is connected to an external device supporting 5.1 CH.

1. Connect an Coaxial Cable between the SPDIF jacks on the TV and the Digital Audio Input jacks on the Digital Audio System. When a Digital Audio System is connected to the SPDIF terminal: Decrease the gain (volume) of the TV, and adjust the volume level with the volume control.Digital Audio System's

External Connection

Connecting PC

WhiteRed

D-Sub Cable (Not supplied)

Each PC has a different back panel configuration. The HDMI jacks do not support PC connection.

1. Connect a D-Sub Cable between VGA/PC IN connector on the TV and the PC output connector on your computer.

2. Connect a PC Audio Cable between PC AUDIO IN jack on the TV and the Audio Out jack of the soundcard on your computer. You should set PC software before you connect a PC to your TV (please refer to "PC

Display'' settings)

Note:

1. Whenever you connect an external device to your TV, make sure that power on the unit is turned off.

2. When connecting an external device, match the color of the connection terminal to the cable.

Supporting signals

Input

DTV

ATV

CVBS PAL/NTSC/SECAM

Input

PC/VGA

Resolution

VGA

SVGA

XGA

SXGA

Mode

DVB-T

PAL BG I DK

SECAM BG DK

640x480 800X600

1024X768

1280X1024

1360X768

Vertical

Frequency

60Hz 60Hz 60Hz 60Hz 60Hz

Input

Component

HDMI

Resolution

480i

480p

576i 576p 720p

1080i

1080p

480p 576p 720p

1080i

1080p

Vertical

Frequency

60Hz 60Hz 50Hz

50Hz 50Hz/60Hz 50Hz/60Hz 50Hz/60Hz

60Hz

50Hz 50Hz/60Hz 50Hz/60Hz 50Hz/60Hz

Basic Operation

Turning the TV On and Off

How to turn the TV on or off

1. Insert the power cord plug into a polarized AC outlet.

2. If TV is in standby mode, press POWER button on the remote control or button on the bottom panel of the LED TV. Otherwise press the MASTER POWER button.

3. Normal picture will be displayed on the screen after 15 seconds. If no signal input, is being received, "No Signal" will be displayed on the screen.

4. If temporary POWER off is required, press POWER button on the remote control or button on the bottom panel.

5. If you want to completely switch off the power for this unit, unplug the power cord plug for this unit.

6. After switching off the unit, you should wait at least 5 seconds before switching on again.

Status indication lamp

On: In standby mode. Off: In power on mode.

Auto power-off

1. If there is no signal, the TV will 10 minutes.automatically enter standby mode after

2. In VGA mode, if no operations occur within 15 seconds, TV will enter standby mode.

Memory before turning TV off

The picture and sound settings and preset channels will be memorised at the point when the TV is turned off. When the TV is started up again it will work accordingly with these settings.

Basic Operation

Menu operation

The main interface

You will enter the main menu directly after the TV is turned on.

Arrow buttons: Select menu and the selected menu's background will be orange. OK button: Enter the options which you've selected. INPUT button: You will enter the relevant function options directly. Those state icons from left to right function as the following in turn:

1.Add to home screen 2. All apps 3. Change wallpaper

4. Search 5. Setting 6. Mass storage

7. Wired

Note:

1. The first area as the photo shown will display the current video images, and it will display snowflake when there is no signal.

2. The second area shows some small desktop plug-ins, select one and press the OK button, you will enter the relevant application program.

3. The third area is the entrance of the shortcut menu, select one and press the OK button, you will enter the relevant shortcut options.

Basic Operation

Menu operation

Applications of the TV

Application menu shows all those applications which came with the TV, along with those that you've downloaded.

Menu Button: Open or Close the app's menu Exit Button: Return to the main menu Arrow Button: Select the application which you want OK Button: Enter the application you've selected. Note: When the applications are of more than one page, and the focus is on left or right side of each line, the left/right buttons can page up/down.

Menu system instruction

TV Menu

Sound Image Program Input Source 3D Function

Menu button: Open the TV menu. Exit button: Close the TV menu. Arrow buttons: Select the application which you want. OK button: Enter the selected application settings menu. Note: Enter the function option by click the status bar.

Sound

Sound Mode Standard Sound Mode Standard

Equalizer Equalizer

Balance Balance

Auto Volume Auto Volume

Surround Surround

SPDIF Mode SPDIF Mode

HDMI Sound HDMI Sound

... ...

0 0

Off

RAW RAW

HDMI HDMI

Time

Sound Mode

You can select the type of special sound to be used when watching a given settings broadcast. Your TV has five sound settings (“Standard”,“Music”, “Movie”,“Sports”, “User”) that are preset at the factory.

1. Press / key to select "Sound Mode" option.

2. Press / key to select one sound mode.

 Standard: Selects the normal sound mode.

 Music: Select the sound mode for music.  Movie: Provides live and full sound for movies.  Sports: Emphasizes bass over other sounds.  User: Selects your custom sound settings (See "User settings for Sound”).

Menu system instruction

Sound

Equalizer

1. Press ▲/▼ key to select an equalizer item.

2. Press OK key to enter the equalizer . submenu The sound settings can be adjusted to suit your user preferences.

1. Press ▲/▼ key to select a particular item.

2. Press / key to decrease or increase the value of a particular item. Note: The adjusted values are stored according

120Hz

500Hz

1.5KHz

5KHz

10KHz

Equalizer

to the selected particular item.

Balance

If the volumes of the left speaker and the right speaker are not the same, you can adjust the "Balance" to suit your personal preference.

1. Press / key to select "Balance" option.

2. Press / key to decrease or increase the value of the item.

Auto Volume

Each broadcasting station has its own signal conditions, and it is inconvenient to adjust the volume every time the channel is changed. “Auto Volume” automatically adjusts the volume of the desired channel by lowering the sound output when the modulation signal is high or by raising the sound output when the modulation signal is low.

1. Press / key to select “Auto Volume" option.

2. Press / key to select “On” or “Off”.

Surround Sound

This is used to turn on surround sound to gain better sound effect.

1. Press / key to select "Surround sound" option.

2. Press / key to select “On” or “Off”.

SPDIF Mode

This is used to select "SPDIF Mode" .This option is only used in HDMI\DTV mode.

1. Press / key to select "SPDIF Mode" option.

2. Press / key to select "RAW" or "PCM".

HDMI Sound

This option is only used in HDMI mode.

1. Press / key to select “HDMI Sound" option.

2. Press / key to select HDMI Sound mode, HDMI or VGA.

Menu system instruction

Image

Picture Mode Dynamic

Aspect Ratio

Color Temp

Backlight

Window Adjust

Picture Mode

Your TV has five picture settings (Standard, Soft, Vivid, User, Dynamic) that are preset at

the factory. Only "User" mode can be set to your preference by adjusting particular items

such as Contrast, Brightness,Color,Sharpness,Tint.

1. Press / key to select "Picture Mode" option.

2. Press / key to select one picture mode.

Aspect Ratio

You can select the picture size which best corresponds to your viewing requirement.

1. Press / key to select “ " option. Aspect Ratio

2. Press / key to set the scale mode. You can also press “ ” key on the remote control to select one of the scale modes. Aspect Each source has different scale modes. (16:9, 4:3, Panorama, Movie, Subtitle, Dot by dot)

Color Temp

You can change the color of the entire screen according to your preference.

1. Press / key to select "Color Temp" option.

2. Press / key to select one color temp.

16:9

Cool

100

...

Standard: Keeps whites white. Warm: Makes whites reddish. Cool: Makes whites bluish.

Adjusting the Backlight

You can the brightness of the entire screen according to your preference.change

1. Press / key to select "Backlight" option.

2. Press/ key to select one backlight mode.

Backlight: Adjusts the brightness of the whole screen.

Window Adjust

This option is only used when VGA mode has signal.

1. Press / key to select “Window Adjust” option.

2. Press OK key to display the “Window Adjust” menu.

Auto Adjust: Allows you to set the TV to self-adjust to the incoming PC video signal. The fine, coarse and position values are adjusted automatically

H-Position: Set horizontal of picture. position V-Position: Set vertical of picture. position Clock/Phase: Remove or reduce picture noise.

Window Adjust

Auto Adjust

H-Position

V-Position

Clock

Phase

...

Menu system instruction

Program

Auto Search

EPG

ATV Manual Search

DTV Manual Search

Program Edit

Signal Information

...

Auto Search

Press / key to select "Auto Search" option. Then

press OK key to start a notice window. In this notice window, you can select country in the “Country Selection” option and set “Search Type” option.

The number of searched channels will be shown on

Search Typethe screen. If you set “ ” to “DTV+ATV”,

When the searching of DTV channels is over , TV will start to search ATV channels. When the whole search is finished, all the channels will be stored in memory, and a message will appear on the screen as per the diagram on the right: NOTE: If you want to exit the whole searching, you can

press EXIT button.

EPG (Used only in DTV)

1. Press / key to select “EPG" option.

2. Press “OK” key to enter EPG submenu. Note: The details operation please see the page 37.

Search Type

Australia

Beligum

Bulgaria

CroatiaAustria

Czech

TV:

DTV:

RADIO:

DATA:

1% VHF CH 5A DTV

EXIT

Exit

ATV/DTV

1/7

Auto Search

Denmark

Finland

France

0 Programmes

Skip

SearchATV Manual

In the ATV/DTV source, you can choose “ATV Manual ” to enter “ATV Manual Search

” menu.Search

 Current CH: You can see the current channel number and you can press/ button to choose the channel you want to modify.

repeatedly in the order. PAL SECAM AUTO  

 Sound System Sound: Select the “ System” option, press / on the remote control or TV.

The s system will be changed repeatedly in the below order. BG Lound  DK  I 

Skip: Select “Skip” option, “be changed” on the remote control or TV to switch, select “ON” to skip current program, select “OFF”  to add the program into the program list.

 Fine Tune: In case of unfavorable image or sound of TV program, you can use “Fine Tune”.

Search: you can use  button to search channels from low frequency to high frequency and use  button to search channels  from high frequency to low frequency. When you have searched a channel, the searching will be paused and you can press it again for other channels after you store the channel.

Frequency: You can see the frequency of the searched channels.

: Select the “Color System” option, press / on the remote control or TV. The color system will be changed  Color System

Menu system instruction

Program

DTV Manual Search

In the ATV/DTV source, you can choose “DTV Manual Search” to enter “DTV Manual Search” menu. You can use /button to choose the channel and press OK button to search, and then the TV will store the DTV channel if there is a DTV signal present.

Program Edit

You can use / button to choose “Program Edit” and enter the menu, press the Blue/Red/Yellow color button on the remote control to skip, delete and move programs, also you can press FAV button to add to your favorite list.

 You can press Skip: / button to choose the channel you want to skip and

press BLUE button to skip it when you change channels.

 Move: You can press / button to choose the channel in ATV mode you

want to move and press YELLOW button to move it.

Delete: You can press RED button to enter "DEL" menu, then choose the 

channel you want to delete and press RED button again to delete.

FAV: If you like the program of a channel, you can choose “FAV” button in the  menu to add it to your favorite list and later you can press “FAV” button in the remote control to choose your favorite programs as soon as possible.

Signal Information(Used only in DTV)

1. Press / key to select “Signal Information" option.

2. Press “Ok”or  key ,you can see the information

of the DTV channel.

NOTE: Signal Quality/Signal Strength (DTV Only): Unlike analogue channels, which can vary in reception quality, digital channels must have perfect reception quality or you will not receive them at all. So, unlike analogue channels, you are not able fine tune a digital channel. If the signal strength indicates that the signal is weak, a possible solution is to adjust your antenna to increase the signal strength. Continue to adjust the antenna until you find the best position with the strongest signal.

DTV Manual Search

CH37

Signal Strength

Signal Quality

DTV: 0 DATA: 0 RADIO: 0

Nine Digital

Nine Guide

C-01

C-04

S-43

S-45

S-02

S-04

S-05

Nine Melbourne

64 QAM

Return

Program Edit

Nine Digital HD

Skip Delete

Signal Information

Channel

NetWork

Modulation

Signal Strength

Signal Quality

DTV

ATV

FAV

84%

100%

Menu system instruction

Input Source

There are two ways to select input source.

1.Input Setup

Press INPUT key on the remote control to enter "INPUT SOURCE" menu. These options for you to select: DTV, ATV, AV, YPbPr, VGA, HDMI1, HDMI2, HDMI3. Use /   key to move the cursor to the input you desired and press OK key to confirm.

Figure1

DTV ATV

2. Input Source menu

DTV

ATV

YPbPr

VGA

HDMI1

HDMI2

HDMI3

YPbPr

VGA

HDMI1 HDMI2

HDMI3

Figure2

1. Press MENU key to display the main menu on the screen.

2. Press / key to select "Input Source” option.  

3. Press OK key to enter submenu.

3D Left Right

3D Up Down

3D-Off

3D-2D

3D Clarity

3D Auto Off

3D Engine ...

1. 2D-3D: Turn source film from 2D into 3D mode.

2. 3D-2D: Turn source film from 3D into 2D mode.

3. 3D-Off: Close 3D mode and set 2D mode.

Menu system instruction

Function

enter password" menu will appear, enter your 4-digit password to enter " " submenu Lock (the default password

is 0000, whereas the uneditable master password is 1980).

Lock System

Lock System1. Press / key to select " " option.

2. Press / key to select "On" or "Off".

Set Password

Password1. Press / key to select "Set " option.

2. Enter your 4-digit password to set the old password.

Choose any 4-digits for your new password and enter them. As soon as the 4 digits are entered, the cursor w to “Confirm password” item, re-enter the same ill skip 4 digits, and your new password has been memorized.

Program Block

1. Press / key to select “Program Block” option.

2. Press OK key to enter Program Lock. In the program list, use Blue key to lock or unlock the program. Once the program is locked and Lock System is on, password is needed to enter it.

Parental Guidance

This option only used in DTV mode.

1. Press / key to select “ ” option. Parental Guidance

2. Press key to select the lock level of the Parental / Guidance: Off, 3, 4, 5, 6, 7, ..., 18.

Lock

Lock System

Set Password

Block Program

Parental Guidance

Set Password

Please enter old password

Please enter new password

Confirm password

Program Lock

C-01

C-04

S-43

S-45

S-02

C-06

C-07

C-08

C-09

C-12

...

Off

ATV

Lock

PVR File System

1. Press MENU key to display the main menu on the screen.

2. Press / key to select “PVR File System” option.

3. Press OK key to enter “PVR File System" submenu, operation refer to “PVR File System”.for detailed

PVR File System

Sekect Disk

Time Shift Size

Format Start

Speed Check

Menu system instruction

Function

Screen Saver

This option is only used in ATV mode.

1.Press / key to select “Screen Save” option.

2.Press / to choose on or off.

Noise Reduction

1. Press/key to select "Noise Reduction" option.

2. Press / key to select "Off", "Low", "Middle", "High" and "DEFAULT” to improve the   picture sharpness. Note: Noise Reduction doesn't work in VGA Mode.

RGB Range

Change the brightness and saturation for a better picture.

1.Press/key to select "RGB Range" option.

2.Press / key to select "16~235" or "0~255".  Note: only available in HDMI mode, please select the appropriate setting according to the DVD Player/STB.

RESET

Select the “Reset” option and press OK key to display a confirm box,and select “Yes” or “No”.

Note: Please use the "Reset" option with caution as it will return all settings and channel memories to factory default

Time

2013/01/18 13:00

On Time

Off Time

Sleep Timer

Time Zone

Off

GMT+8:00

Clock Setting

In the first item, press OK button to enter the "Clock Setting" menu to set the Date and Time. In the "Auto Mode" item,you can get the time from DTV or Net.

On Time

In "On Time” item, press OK button to enter the submenu, set the time to turn on the TV set, when the TV set is in the standby mode.

Clock Setting

Auto Mode Off

Date

Time

Switch On

Time

Source

2013-04-18

09:16

On Time

12:00

DTV

Menu system instruction

Time

Off Time

In "Off Time" item, press OK button to enter the submenu, set the time to turn off the TV set.

Off Time

Switch On

Time 00:00

Sleep Timer

1. Press / key to select "Sleep Timer" option.

2. Press / key repeatedly until the desired time appears (Off, 10min, 20min, 30min, 60min, 90min, 120min, 180min, 240min). Notes:

1.The sleep timer you have set will be cancelled when the TV turns off or if a power failure occurs.

2.When the time is less than 60 seconds, remind information will be displayed on the screen. Press any key button to cancel timer function.

Time Zone

You can choose it to modify your time zone in the TV set.

1. Press / key to select "Time Zone" option.

2. Press / key to select time zone.

PVR

PVR File System

WARNING:

1. Before connecting your USB device to the TV, please back up your files to prevent them from damage or loss of data.

2. A USB disk must be formatted when first used for PVR. Any existing data on the disk will be lost during the formatting process. Please back up your disk if you do not want to lose this data. You are recommended to use a dedicated disk for PVR use only. Do not disconnect disk or power during formatting.

3. Do not modify PVR files on a PC.

Note: Make sure your USB device is compatible with the TV and able to support PVR recording.

Select Disk

C: FAT

null

Cancel

D: FAT

null

512M

Menu system instruction

PVR

“” to Select Disk: Press “OK” button to enter submenu and press / choose the disk for PVR.

Time Shift Size: Press “OK” button to enter submenu and press / choose the size. “ ” to Format: Press “OK” button to enter format submenu. The disk must be when first used formatted

for PVR. Do not disconnect disk or turn power off during formatting.

When formatting your disk, a progress bar will appear on the display. NOTE: The larger

your device the longer it will take to format. The device may take many minutes to format, this is not a malfunction, please wait for the formatting to finish. Speed Check: Test your disk speed.

PVR Guide

If the disk for PVR is ready, the programs can be recorded in DTV mode.

Time shift

In DTV mode, press “ / ” button to pause the DTV program, press it again to continue play. The length of

time a program can be paused depends upon the setting in the PVR File System. Press “EXIT” to stop

the time shift.

Press the PLAY button to continue playing the program from the point where it was paused. NOTE: Time Shift will stop if you change channels, change inputs or go into standby mode while in Time Shift mode.

CH9 Nine Digital

Play

MALCOLM IN THE MIDDLE

00:00:00

Stop

Pause Rev

00:00:00

SlowMotion

TimePlay

89%

C:FAT

Instant recording

1. Select the desired channel then press the “ ” button on the remote control to start recording the current broadcast, a progress bar will be displayed at the bottom of the screen.

2. Recording stops when you press the EXIT button and the recorded file is stored in the external USB device automatically.

HOME

Play/Pause

Stop

Record Forward

Back

NOTE: You can only watch channels on the same frequency as the program being recorded. If you try to change to another channel or come to the main interface a message will appear prompting you to continue or not “STOP RECORDING. System will stop record if user want to channel up/down, Confirm or Cancel.”

Menu system instruction

PVR

DTV EPG (Electronic Program Guide)

In DTV mode, press “GUIDE” button to enter the Electronic Program .Disabled At Guide menu, press "RED” button to "Record" Setting.

Once

EXIT

30 16

Reminder

Once

EXIT

Reminder

Back

2007-01-18 16:01

Monday Tuesday

INFO

V1.0.12 Build 7587

INFO

2014-01-18 15:53

Monday Tuesday

INFO

V1.0.12 Build 7587

INFO

Wednesday

EPG

DTV

9 Nine Digital

90 Nine Digital HD

99 Nine Guide

Schedule

Record

Thursday Friday

Saturday Sunday

16:00 THE SHAK

Record Setting

Channel CH 90 Nine Digital HD

Start Time Minute Hour Month Date

End Time

Minute Hour Month Date Mode

Switch Day

At Guide menu, press "OK" button to "Reminder Settings". Note: Press / button to adjust the scheduled time, press OK

button to save the setting.

EPG

DTV

9 Nine Digital

90 Nine Digital HD

99 Nine Guide

Schedule

Record

Thursday Friday

Saturday Sunday

16:00 THE SHAK

Reminder Settings

Channel 90 Nine Digital HD

Minute

Hour

Month

Date

Mode

Switch Day

HOME

Guide

Red

Blue

Press BLUE button to go to the Schedule interface.

Schedule

Channel ID Channel Name Event Name

90 CH90 Nine Digital HD Once 2007-01-18 16:30 NATIONAL NINE AFTERNOON...

99 Ch99 Nine Guide Once 2007-01-18 17:00 THE SHAK

2007-01-18 16:01

Delete

Return

Digital Media Player

Introduction

This TV is embedded with one USB port digital media player. It can find devices that support USB1.1/2.0/3.0, including flash disk, USB hard disk and digital camera. It supports functions as: Display pictures, Play music files, Play video files. Note: please do not remove the cable during the data transfer. It may cause problems for the system.

Data

Picture

Music

Video

MPG,MPEG, , ,MP4 MOV MKV

Format

JPG,JPEG,PNG,BMP

MP3, AAC

Device and File Management

Initialization Interface

On the main interface (page.24), click the “Mass storage” state icon to enter the USB channel. If no USB disk is inserted, the system will prompted you to insert the USB device,

whilte the screen displays "Storage DeviceRemove” message, as shown below.

Disk Choice

Storage DeviceRemove

At present there is no storage equipment can be used, will soon quit this module.

When you insert a USB disk, the interface shown in Figure 2. OK key: to enter the selected letter.

Disk Choice

Current Version: 1.2.00 Bulid:16114

Quit

Figure 1

Current Version: 1.2.00 Bulid:16114

Figure 2

Digital Media Player

USB support character

1. Photo

Press menu button to play/exit the "photo menu". Those menu items from left to right function as the following in turn:

a.Wallpaper b.List c.Prev d.Play/Pause e.Next f.Stop g.Sequence h.AnticlockZLVH URWDWHL.ClockwiVHURWDWH j.Zoom in k.Zoom out l.0RYH

002.jpg

Wallpaper

List

Play/Pause

Play

Stop

2. Music

Those menu items from left to right function as the following in turn: a. Lyric b. Prev c. Pause/Play d. Next e. Play Mode

Lyric

Pause/Play

Play Mode

Move

Zoom out

Zoom in

Clockwise rotate

Anticlockwise rotate Sequence

Digital Media Player

USB support character

3. Movie

Press menu button to play/exit the "movie menu". Those menu items from left to right function as the following in turn: a. Prev b. Pause/Play c. Next d. Stop e. Advanced setting

Pause/Play

Advanced setting Stop

4. Sync View

Press 2D/3D button to open the Sync View menu. This menu has two group functions, the top row functions use for 3D setting (pg.31 for details), the bottom row functions use for Sync View. (SyncView Only works in USB mode.)

3D Left Right 3D Up down 3D -Off 3D - 2D 2D - 3D 3D Clarity 3D Auto 3D Engine

SyncView

Select the Sync View item and press OK to enter the Sync View mode.

3D Left Right 3D Up down 3D -Off 3D - 2D 2D - 3D 3D Clarity 3D Auto 3D Engine

SyncView

Sub Channel Enter Sub Back Main

Digital Media Player

USB support character

Select the Sub Channel item and press OK to open the Sub Channel selection menu. Press / key and press OK to select a channel.“ ”

DTV

ATV

YPbPr

VGA

HDMI1

HDMI2

HDMI3

3D Left Right 3D Up down 3D -Off 3D - 2D 2D - 3D 3D Clarity 3D Auto 3D Engine

Sub Channel

Enter Sub Back MainSyncView

Select the Enter Sub item and press OK to enter the sub channel you want.

3D Left Right 3D Up down 3D -Off 3D - 2D 2D - 3D 3D Clarity 3D Auto 3D Engine

SyncView

Sub Channel

Enter Sub

Back Main

Select the Back Main item and press OK to exit sync view.

3D Left Right 3D Up down 3D -Off 3D - 2D 2D - 3D 3D Clarity 3D Auto 3D Engine

SyncView

Enter SubSub Channel

Back Main

Troubleshooting

If you have any problem, check the couter measures for each symptom listed below. The following symptoms may have . adjustment rather been caused by inappropriate than actual malfunction of the unit. If the trouble persists, contact the Kogan Customer

Care Centre for more information.

Symp tom s

No pow er

No pic tur e

Good p ict ure b ut no soun d

Good sound but abnormal color or no picture

No res pon se to r emote cont rol

Full s cre en fl ickering unde r VGA

Please check the power cord plugged in and that the power outlet works. Unplug the power cord and plug it in after 60 seconds and restart the TV.

Please check antenna connection. Station may problems, please tune to be experiencing another station. Please adjust the settings of contrast and brightness.

Please increase the volume. Please check TV is under mute mode, press MUTE button on the remote control. Please check sound settings If external devices are being used, check their volumes are not set too low or turned off. If using AVI or Component inputs, please make sure cables are connected properly and not loose. If using DVI to HDMI cable, a separate audio cable is required. Make sure a headphone jack is not connected..

Please check antenna connection and antenna condition. If using Component input, please check Component connections, incorrect or loose connections may cause colour problems or cause the screen to be blank.

Batteries of remote control may have exhausted, if necessary, please change the batteries. Clean the remote control lens. The distance between LED TV and remote control should be within 8m, within recommended operating angle and path is free of obstructions.

V-HEIGHT value may be set too big, restart computer and enter safe mode, then set monitor parameters to correct value according to adjustment description.

Poss ibl e sol utions

Hori zon tal s tripes unde r VGA

Colo red d ots m ay be pres ent o n the s creen

Pic tu re is bre aking up

Sample phase may be deflected, adjust phase according to picture position.

Although the LED screen is made with high-precision technology and 99.99% or more of the pixels are effective, black dots may appear or bright points of light (red, blue, or green) may appear constantly on the LED screen. This is a structural property of the LED screen and not a malfunction.

Keep the TV away from noisy electrical sources such as cars, hair dryers, welders, and all optional equipment. Electrical atmospheric interference such as local or distant lightning storms may cause picture to break up. When installing optional equipment, leave some space between the optional equipment and the TV. Check the antenna and connection. Keep the antenna away from any power or input/output cables.

Troubleshooting

Afte r Aut o Tun ing onl y some cha nnels a re avai lable

Chan nel canno t be sele cted

USB not pl aying

Picture is distorted, macroblock, small block, dots, pixelization, etc

Nois e fro m spe aker

TV turns off automatically

TV tur ns on auto mat ica lly

Pict ure i s not s hown in full s cre en

Check your area is covered by Digital Video Broadcasts. Try re-tuning or manually tuning missing ch an ne ls. Check that you are using the correct antenna type - please see pg.16 'Anten na connection'.

Chec k if t he chan nel has bee n blocked i n the main me nu sett in gs.

Please check connecting USB cable and power supply is connected. Hard drive has not been formatted. Please make sure USB disk is compatible and the multimedia data formats are supported.

Comp ression o f video con tents m ay cause di stort ion espe ciall y on f ast movin g pictu res such as s ports and acti on movies .

Chec k cab le co nnection s, ma ke su re a vide o cab le is n ot conn ect ed to a n audio inpu t. Low si gna l lev el ma y cause s oun d dis torti on.

Chec k if th e Off Time r is se t to On in th e Set up me nu. Slee p Time r may h ave been ena ble d. If the re is n o sig nal for abou t 10 mi nut es from a n inp ut, the TV will tur n off, se e Auto S lee p pg. 33. If con nec ted t o your PC , che ck yo ur PC power se tti ngs . Make s ure t he AC po wer cord is pl ugg ed in s ecurely to the wa ll ou tle t and the T V.

Chec k if th e On Tim er is set to On in t he Se tup menu.

Blac k bar s on ea ch si de will b e sho wn on H D channels when d isp lay ing SD (4:3) c ont ent s. Blac k bar s on Top & Bott om wi ll be shown on m ovi es th at have a spe ct ra tios differe nt fr om yo ur TV. Adju st pi ctu re size opti on on y our e xtern al de vic e or TV to full sc ree n.

Troubleshooting Picture defects and the reason

Ghost ing may als o occu r when stil l picture s are displ ayed cont inuo usly. It ma y disappe ar aft er a few mom ents.

Kogan KALED423DSMTZB User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual