Kogan KALED40XXXZA User Manual
Important Safety Instructions and Maintenance
Important Safety Instructions
CAUTION
Risk of electronic shock, do not open.
Do not attempt to service this product yourself
as opening or removing covers may expose
you to dangerous voltage or other hazards.
Refer all servicing to qualified service personnel.
If the following problems occur:
Turn off the TV set and unplug the AC power cord
immediately if any of the following problems occur.
Ask your dealer or service centre to have it checked
by qualified service personnel
When:
- AC power cord is damaged.
- Poor fitting of AC power outlet.
- TV set is damaged by being dropped, hit or having something thrown at it.
- Any liquid or solid object falls through openings in the cabinet.
To reduce the risk of fire or electric shock, do not
expose this product to rain or moisture.
The apparatus shall not be exposed to dripping
or splashing and no objects filled with liquids,
such as vases, shall be placed on the apparatus.
The screen and cabinet get warm when the TV
is in use. This is not a malfunction. In case of
smoke, strange noise or strange smell from the
unit:
· Turn off the power switch immediately;
· Disconnect the power plug from the power
outlet;
· Contact your dealer or service centre. Never attempt to make repairs
yourself because this could be dangerous.
Never push objects of any kind into the set
through the cabinet slots as they may touch
dangerous voltage points or short-circuit parts that
could result in a fire or electric shock. Never spill
liquid of any kind on the set. Use special caution
in households where children are present. The apparatus is not suitable for children
under 3-year to operate.
Do not overload wall outlets, extension cords or
adaptors beyond their capacity, this can result in
fire or electrical shock.
Power-supply cords should be routed so that they
are not likely to be walked on or pinched by items
placed upon or against them, paying particular attention to cords at plug end, adaptors
and the point where they exit from the appliance. The mains plug is used as the
disconnect device. It shall remain readily accessible and should not be obstructed
during intended use. Make sure to plug the power cord in until it is firmly inserted.
When removing the power cord, make sure to hold the power plug when pulling the
plug from the outlet, do not pull the plug out by the wire. NEVER touch the plug or
power cord with wet hands. To disconnect the apparatus from the mains power, the
plug must be pulled out from the mains socket, therefore make sure the mains plug
is always easily accessible.
High Voltage
Do not open
1
Important Safety Instructions and Maintenance
Important Safety Instructions
Do not push or scratch the front filter, or place any objects on top of the TV set. The
image may be uneven or the screen may be damaged.
To avoid the fire, no naked flame source,
such as lighted candles, should be placed on the
apparatus.
An outside antenna system should not be located in
the vicinity of overhead power lines or other electric
light or power circuits, or where it can fall into such
power lines or circuits. When installing an outside
antenna system, extreme care should be taken to keep
from touching such power lines or circuits as contact
with them might be fatal.Ensure the television is not
overhanging the edge of supporting furniture.
When not in use
If you will not be using the TV set for several days, the
TV set should be disconnected from the AC mains for
environmental and safety reasons. As the TV set is not
disconnected from the AC power when the TV is turned
off at the standby switch, pull the plug from the AC power
outlet to disconnect the TV completely. However, some
TV sets may have features that require the TV set to be
left in standby to function correctly. In the case of lightning,
unplug the TV set from the outlet immediately. Never
touch the antenna wire during lightning.
Installation
Do not pull the plug out by the wire;
Never touch the plug with wet hands.
Excessive from earphones and headphones volume
can cause hearing loss.
The ventilation should not be impeded by covering the
ventilation opening with items, such as newspapers,
tablecloths, curtains, etc.
At least 10 cm space should be left around the
apparatus for sufficient ventilation.
The product should be situated away from heat
sources such as radiators, heat registers, stoves, or
other products (including amplifiers) that produce heat.
Place the apparatus in such a position that the screen
is not exposed to direct sunlight. It is best to have soft
indirect lighting while watching and avoid completely
dark environments and reflection from the screen as
these may cause eye fatigue.
Keep the TV set away from any equipment emitting
electromagnetic radiation.
2
Important Safety Instructions and Maintenance
Installation
Do not place the set on an unstable cart, stand, table
or shelf. The set may fall, causing serious personal
injury as well as damage to the product. Use only with
the cart, stand, tripod, bracket, or table specified by
the manufacturer, or sold with the apparatus. An
appliance and cart combination should be moved with
care. Quick stops, excessive force, and uneven
surfaces may cause the appliance and cart
combination to overturn.
Do not place this apparatus near water, for example,
near a bath tub, wash bowl, kitchen sink, or laundry
tub; in a wet basement; or a swimming pool; and
the like;
When the TV being moved in from cold place, it needs
Move
LED Screen
Although the LED screen is made with high precision technology and 99.99% or
more of the pixels are effective, black dots may appear or bright points of light (red,
blue or green) may appear constantly on the LED screen. This is a structural property
of the LED screen and is not a malfunction.
If the surface of the LED panel cracks, do not touch it until you have unplugged the
AC power cord. Otherwise electric shock may result.
Do not throw anything at the TV set. The LED panel may break from the impact and
cause serious injury.
Precautions When Displaying a Still Image
A still image may cause permanent damage to the TV screen.
Do not display still images and partially still images on the LED panel for more
than 2 hours as it can cause screen image retention. This image retention is
also known as "screen burn". To avoid such image retention, reduce the
degree of brightness and contrast of the screen when displaying a still image.
Watching the LED TV in 4:3 format for a long period of time may leave traces
of borders displayed on the left, right and centre of the screen caused by the
difference of light emission on the screen. Playing a DVD or a game console
may cause a similar effect to the screen. Damages caused by the above effect
are not covered by the Warranty.
Displaying still images from Video games and PC for longer than a certain
period of time may produce partial after-images. To prevent this effect, reduce
the 'brightness' and 'contrast' when displaying still images.
Cleaning
Cleaning and handling the screen
surface and cabinet. Disconnect
the unit from the AC outlet before
cleaning. To remove dust, wipe
gently with a soft, lint free cloth. If
required use a slightly damp cloth.
thinner
thinner
solvent
solvent
some right time for dew inside unit evaporating fully
before turn on the unit;
To prevent injury, this apparatus must be securely
attached to the floor/wall in accordance with the
installation instructions.
MAINS PLUG
Wipe the mains plug with
a dry cloth at regular
intervals. Moisture and
dust may lead to fire or
electrical shock.
Use care not to subject the TV's surfaces to detergent.
(A liquid inside the TV could lead to product failure, fire or
electrical shock.)
Use care not to subject surfaces to bug repellent, solvent,
thinner, or other volatile substances as this may deteriorate the
surface and finish of the cabinet.
3
Important Information
Keep sm all acc esso ries ou t of reach of children so they are not mis takenly swallowed.
Table of Contents
Accessories
Introduction
Features
Specifications
Stand and wall-mounting instructions (optional)
General Description
Overview of back panel
Overview of front panel
Overview of remote control
Teletext
Installing Batteries in the Remote Control
External Connection
Antenna connection
Connecting VCR
Connecting a Camcorder
Connecting a DVD Player/Set-Top Box
Connecting DVD Player/Set-Top Box via HDMI
Connecting Digital Audio System
Connecting PC
Supporting signals
Basic operation
Turning the TV on and off
Menu operation
Menu system instruction
Picture
Sound
Channel
Time
Option
Function
PVR
Digital Media Player
Introduction
Device and File Management
USB Support Character
Photo
Music
Movie
Text
Troubleshooting
Picture defects and the reason
5
6
6
7
8
10
10
11
12
14
16
16
16
17
18
19
20
21
22
23
24
24
25
27
27
29
31
33
34
36
37
40
40
41
41
41
43
44
47
49
51
4
Accessories
Please make sure the following items are included with your LED TV. If any items are
missing, contact your dealer.
POWER
INPUT
1 2 3
6
4 5
789
RECALL
INFO
0
FREEZE SLEEP
MENU
FAV
CH.LIST
OK/
REC LIST
GUIDE
EXIT
USB
DTV HDMI
ASPECT
MUTE
VOL PROG
AUDIO LANG
BLUE
RED GREEN YELLOW
INDEX
TEXT
HOLD SIZE
SUBTITLE
REVEAL CANCEL
MIX
PgUp PgDn
SUBCODE
SOUND
TIME
PICTURE
Remote Control
5
Introduction
Features
TV adopts 40" TFT display screenLED
Zero X radiation complies to green environment protection requirement
Connect to computer directly to create a TV/monitor combo.
16:9 wide screen
Auto tuning and fine tuning
HDMI input
Component Compatible (480i; 480P; 576i; 576P; 720P; 1080i; 1080P)
PC-RGB
Programmable sleep timer
Wide range voltage input
No-signal automatic power off
Input terminals used for external equipment connection
KALED40XXXZA
Model
ANTENNA jack
HDMI inputs
Computer PC-RGB input
USB inputs
COMPONENT input
CVBS output
AV inputs
SPDIF output
Headphone output
1
3
1
2
1
1
1
1
1
6
Introduction
Specifications
<0.5W
KALED40XXXZA
40”Diagonal(max.)
1920X1080
5
70W
931x240x615mm
931x59x561mm
11.1Kg
8.8Kg
Note:
- Design and specifications are subject to change without notice.
- Weight and Dimension shown are approximate.
7
Stand and wall-mounting instructions (optional)
How to assemble the stand
If you need to remove or assemble the stand please read the following instructions.
- Before attaching/detaching the stand, make sure to turn off the TV.
- Before performing work, spread cushioning over the base area to lay the LED TV on.
This will prevent it from being damaged.
1) Fix the bracket and the Transition board on the stand with four screws.(figure 1)
2) Put the television on the table, fix the stand and the unit with four screws given in the
carton.(figure 2)
Screws
(4 x B-ST4*30)
Transition board
Stand
Bracket
B- ST4*30
Screws
Figure 1 Figure 2
(4 x M4*10)
M4*10
8
Stand and wall-mounting instructions (optional)
How to mou nt t he L ED T V on t he w all
1. Wall 2. Nylon sleeve
3. Wall-mounting bracket
4. Self-tapping screw
5. Wall-mounting screw
6. Rear cabinet
7. Wall-mounting Bolt 8. Screw
Wall-mounting instruction:
1. Please ensure the distance of wall-mounting holes is 200mm or 400mm on the back
cabinet before you mounting your TV on the wall.
2. Mark the four mounting screw holes with pencil on the wall by using wall-mounting
bracket(4) as ruler. Drill these four mounting screw holes on the wall.
3. Drive Nylon sleeves(2) into the screw holes on the wall.
4. Fasten wall-mounting bracket (3) on the Nylon sleeves(2) with self-tapping screws(4)
on the wall.
5. Fasten wall-mounting screws (5) into the two screw holes on the rear cabinet(6);
6.Tighten wall-mounting bolt(7) on the bottom of the rear cabinet with screws(8).
7. Left the TV and hang it on the wall by two people.
Note:
1. Please mount your TV on the strength of the wall for withstanding the TV’s weight.
2. Be careful not to scratch panel and TV cabinet when your fasten the screws on the TV.
9
General Description
Overview of back panel
You can connect the TV with video devices such as DVD/VCD player, VCR and video camera
to enjoy the high quality picture.
Video output
Camcorder
VIDEO
SPDIF
SPDIF
DVD player
HDMI 2 HDMI1/ MHL
PC-R GB
PC
COMPO NENT/ AV/PC
R L
Y/AV
PB PR
DVD player
PC (HDMI-output)
ANT IN
Blu-ray disc player
USB 2
USB 1
USB 2
USB 1
Headphone
10
General Description
Overview of front panel
The buttons on the lower-right panel control your TV’s basic features, including the
on-screen menu. To use the more advanced features, you must use the remote control.
6
Standby button
Press button to toggle between
normal and standby mode.
PROG
Press to change programs.
In the on-screen menu, use the
PROG buttons as up/down
arrow buttons.
3
245
7
INPUT
POWER INDICATOR
Red:In standby mode.
Green: In power on mode.
7
1
11
General Description
Overview of Remote Control
INPUT
POWER
1 2 3
4 5
8
7
INFO
0
FREEZE
MENU
CH.LIST
OK/
REC LIST
GUIDE
MUTE
AUDIO LANG
HOLD
MIX
PICTURE
USB
YELLOW
SIZE
REVEAL CANCEL
PgUp PgDn
TIME
DTV HDMI
VOL PROG
RED GREEN
INDEX
SUBTITLE
SOUND
6
9
RECALL
SLEEP
ASPECT
SUBCODE
1. INPUT: This button is used to switch among
different sources.
Select a source and press OK button to confirm.
2. POWER: Press this button to switch to standby
mode, and press it again to turn TV on.
3. Digital buttons(0~9): To select channel with
digital buttons.
4. INFO: This button is used to start the "Current
Service Banner" application that provides
information about the current service.
5. RECALL: Switch to the previous program.
FAV
6. FREEZE: Press this button to freeze the image.
7. MENU: Press this button to display main menu or
exit the menu. When you are in the submenu, you
can press it to return the main menu.
8. SLEEP: TV will be switched off automatically at
preset sleep time if you have set sleep timer. Use
EXIT
your remote control to set the sleep timer.
Press SLEEP button on the remote control, then
press this button again to set sleep time: off, 10,
20,30, 60,90,120,180, 240 min. Press MENU
button to exit when you have set the sleep timer.
After you have set sleep timer, press SLEEP button
again, you will see the Remaining time.
BLUE
TEXT
Notes: The sleep timer you have set will be
Cancelled when the TV turns off or if a p ower
failure occurs.
9. CH.LIST: Press it to show channel list on screen.
10. FAV: Press it to display favorite list.
11. Arrow buttons: Press these buttons to move
cursor up/down/left/right for menu.
12. OK/REC LIST: Press this button to display a list
of recorded programs. In main menu and submenu
it is a validation button.
13. GUIDE: In DTV source, this button is used to
start the EPG application. No function if country
select New Zealand.
14. Exit: Exit the menu.
15. DTV: Switch to DTV mode.
16. HDMI: Switch to HDMI1/HDMI2/HDMI3 mode.
12
General Description
Overview of Remote Control
17. USB: Switch to USB mode directly or call the
INPUT
POWER
1 2 3
4 5
8
7
INFO
0
FREEZE
MENU
CH.LIST
OK/
REC LIST
GUIDE
MUTE
AUDIO LANG
HOLD
MIX
PICTURE
USB
YELLOW
SIZE
REVEAL CANCEL
PgUp PgDn
TIME
DTV HDMI
VOL PROG
RED GREEN
INDEX
SUBTITLE
SOUND
6
9
RECALL
SLEEP
FAV
EXIT
ASPECT
BLUE
TEXT
SUBCODE
control menu in USB mode. Please see the
details in “Digital Media Player” .
18. ASPECT: Press this button to switch the screen
mode.
19. VOL and VOL: Press these buttons to
adjust TV volume.
20. PROGand PROG: Press these buttons to
change channel upward or downward.
In the teletext, these buttons are used to
display the next page and previous page.
21. MUTE: Press this button to shut off sound of the
TV, press again to restore TV sound.
22. Button/Audio Lang: sourceIn ATV , the button
is used to set NICAM sound system.
In DTV , the button is used to set the audiosource
language.
In USB source,the button is used to make language
soundtrack switch(video).
23. Red/Green/Yellow/Blue Command: These four
buttons are used to request linked buttons with the
current menu/page.
24. Teletext buttons: Detail operation please refer to
"Teletext “ in the next page.
25. IncludingDigital media player control button:
play/pause, stop, previous file, next file, page up,
page down, backward, forward, is used to control in
USB mode.
Please refer to instructions in the section relevant
of multimedia player.
26. SOUND: This button is used to select the sound
mode.
StandardMusicMovieSportsUser
27. PICTURE: This button is used to adjust user
picture mode, press this button repeatedly and
select one of four settings.
Standard Mild Br ig ht User Sports
28. MIX ( ): Teletext buttons for mix function, please
refer to TTX description page. It is also used for
recording function when TV is on DTV mode, please
refer to PVR page.
13
General Description
Teletext
INPUT
POWER
1 2 3
4 5
8
7
INFO
0
FREEZE
MENU
CH.LIST
OK/
REC LIST
6
9
RECALL
SLEEP
FAV
Teletext is an information system broadcast by certain
channels which be consulted like a newspaper.
It also offers to subtitles for viewers with hearing
problems or who are not familiar with the transmission
language.
You can press these buttons to operate the teletext:
Text
Press TEXT button to enter or exit teletext mode.
Hold
In DTV source, this button is used to start the EPG
application if no TTX on when country select
New Zealand.
Press HOLD button to toggle Hold function on or
off. When Hold is switched on, the page acquisition
is stopped. When Hold is switched off, the page
acquisition is started.
GUIDE
DTV HDMI
EXIT
USB
ASPECT
Size
Press SIZE button one time to display the upper
half of the screen in double height, press the SIZE
button two times to display the lower half of the
MUTE
VOL PROG
AUDIO LANG
RED GREEN
INDEX
SUBTITLE
SOUND
HOLD
MIX
PICTURE
13
BLUE
YELLOW
TEXT
SIZE
REVEAL CANCEL
PgUp PgDn
SUBCODE
TIME
screen in double height, press three times to
display the full screen in normal size.
Red/Green/Yellow/Blue Command
These four buttons are used for quick access to
different pages as numbered at the bottom of the
screen.
Index
Press INDEX button, then index page displays.
Reveal
Pressing this button will reveal any hidden data
(answers to quizzes for example).Press the REVEAL
button again to return to normal screen.
14
General Description
Teletext
INPUT
INFO
FREEZE
CH.LIST
GUIDE
DTV HDMI
VOL PROG
RED GREEN
INDEX
13
SUBTITLE
SOUND
POWER
1 2 3
4 5
8
7
0
MENU
OK/
REC LIST
USB
MUTE
AUDIO LANG
YELLOW
SIZE
HOLD
REVEAL CANCEL
MIX
PgUp PgDn
TIME
PICTURE
6
9
RECALL
SLEEP
FAV
EXIT
ASPECT
BLUE
TEXT
SUBCODE
Cancel
The CANCEL button will exit from any Teletext on
the display. Press CANCEL button again to exit
Teletext and return to live TV broadcast.
Subtitle
Turning the Teletext subtitles on or off.
Subtitles is a separate mode with only a few
buttons available. There will be no OSD visible
other than the Teletext Subtitles.
Subcode
Subcode mode gives the possibility to select
certain subcode pages of a Teletext page.
Entry of digits within the range 0...9 for current
subcode entry. If the digit completes the entry,
a page request is started.
Press buttons to change thePROG/ PROG
subcode pages.
Time
This button is used to show the time of the
Teletext.
Digital buttons(0~9)
You can press them to enter the number of the
Page required.
PROG/PROG
You can press them to change page upward or
downward.
13
Mix
Press MIX button, the teletext page changes
transparent, TV content and teletext page
content will display at the same time.
Press MIX button again to exit MIX mode.
15
Loading...