Kogan KALED27MONB User Manual

CATALOGUE

 Note- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - ---1-2
 Prevention Measures - - - - - - - - - - - - - - - - - - - - - - - - - - - - --4
 Special Notes of LCD Monitor - - - - - - - - - - - - - - - - - - - - - -- 5
 Instructions before Using - - - - - - - - - - - - - - - - - - - - - - - - -- -5
 Features - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -5
 Packing List- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 6
 Installation Instructions - - - - - - - - - - - - - - - - - - - - - - - - - - - 6
 Control and Connection- - - - - - - - - - - - - - - - - - - - - - - - - - -- 7
 Angle Adjusting - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 8
 Operation Instructions - - - - - - - - - - - - - - - - - - - - - - - - - - - - 9
 General Descriptions - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -9
 Front Panel Control - - - - - - - - - - - - - - - - - - - - - - - - - - - - ---10
 How to Use the OSD Adjustment - - - - - - - - - - - - - - - - - - - -- 12
 Picture Adjusting - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -- 13
 Plug and Play - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -13
 Technical Support (FAQ) - - - - - - - - - - - - - - - - - - - - - - - - - - 16
 Wrong Information and Possible Solutions- - - - - - - - - - - - - -18
 Appendix- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -19
 Specifications- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -- 20
 Factory Presets Mode Table - - - - - - - - - - - - - - - - - - - - - - -21
 Joint Pin Distribution- - - - - - - - - - - - - - - - - - - - - - - - - - - - -22

Please read these instructions carefully before operating the monitor.
A copy of the manual should be kept for future reference.
Notes:

1. Do not perform any modifications to the monitor as this may damage it and cause your
warranty to become instantly void.

2. Any modifications carried out by the customer that cause damage to the monitor,
computer equipment or injury or destruction due to malfunction are not the
responsibility of Kogan. The customer is entirely responsible for any modifications or
changes to the monitor or power cables.

Warning:

To prevent fire or explosion, please don't put the display in the rain or a wet environment.
There is dangerous high pressure within the display, so don't open the shell. Please contact
the Kogan customer support team if you need assistance with the monitor.

Prevention measures

• Don't put the display close to water, such as in a bathroom, dishwasher, kitchen, washing

machine, swimming pool or a humid basement.

• Don't put the display on an instable car, chair or table. If the monitor falls down, it may

damage the user and equipment. If you mount the monitor on a wall or shelf, the fixed
installation is entirely the responsibility of the customer and Kogan are not responsible if the
monitor comes loose and falls.

• There are many long and narrow holes in the upper and bottom of the shell for ventilation.

To ensure continuous operation with no overheating, these cooling holes must not be blocked
or covered. The monitor should not be placed on soft surfaces such as a bed, sofa or carpet.
It also should not be near a radiator or other heat source. Without good ventilation, the
monitor shuld not be put in a bookcase or cabinet.

• If the display is not to be used for a long time, please disconnect the power. This can

prevent damage caused by an abnormal power surge.

• Do not let the power socket to get overloaded, or it may cause the fire or electric shock.

• Don't put a foreign body into the machine, as this can cause a short circuit and lead to fire

or shock.

• Do not open the casing, or it may suffer from high pressure or other dangers. If the monitor

fails, please contact the Kogan customer support team.

• For safety, please ensure the power supply voltage 100 ~ 240 V AC, current 5A at least.

• Please insert the plug into an easily accessible power socket, so that it can easily be reached

and disconnected from the power supply in the event of fire, electric shock or thunderstorm.

Special Notes of LCD monitor

LCD monitors may display the the following issues, which are not faults.

Note

• The picture may blink and flash upon first use while it is going through initial setup. If the

issue continues, please turn off the display, wait 30 seconds and then turn the monitor on
again.

• When you use different desktop patterns, the screen brightness may be slightly uneven.

• LCD screen pixel technology has reached 99.99% quality levels, but in the displaying

process, it may also display a 0.01% or less of pixel loss or brightness loss.

• Due to the characteristics of LCD screens, pixel residue will never appear in normal use.

However, when the same static image stays displayed for a long time before switching, the
previous picture may continue to be retained. This is called 'screen burn'. To avoid screen
burn, the best way is to use a monochrome display or alternately a dynamic moving screen
saver when you don’t need the PC or the system. Additionally, you should power off the
electricity for two hours after every 12 hours’ working.

• When the screen turns black, flickers or doesn't power up at all, please contact the Kogan

customer support team. Please do not attempt to repair the monitor by yourself.

Instructions before using

Features

* (68.5cm)27” TFT color LCD monitor
* 16:9 wide screen
* bright and beautiful pictures
* suggesting resolution: 2560×1440 @ 60 Hz
* used for drawing design, medical and financial area

Packing list

The box contains the following items:

1. LCD monitor/base

2. Product specification

3. Signal lines (including DVI, VGA line)

4. Power cord

5. USB cable

6. Mini DP to DisplayPort cable

Control and Connection

Visual connections

Signal line connection: Choose either the the 15 stitch plug or the DVI line of the 24 needle
plug to connect the output port of the computer to the input port of the monitor. Finally use
the screw to fix it.

Power

1. First confirm that the power cord conforms to the area standards.

2. The LCD monitor has a broad power supply voltage scope when working, and it could be

used in the area of 100/120 V or 220/240 V AC.

3. One side of the power cord should be connected with the LCD power port, and the other

side connected to the wall power outlet or the power socket of the computer.

Image one: connections

1 2 3 4 5

Power Port VGA Port DVI Port USB Port USB Port