USER MANUAL
KALCD39FHDXA
Contents
Important safety instructions 4
Usage conditions and restrictions 4
Electrical safety, power cord and plug 5
Position 5
Cleaning and maintenance 5
Remote Control 7
Accessories 10
Assembly 11
Assembling the stand 11
Wall mounting 12
Controls and Connections 13
Getting Started 16
Basic Operation 17
Electronic Program Guide (EPG) 18
Recording - PVR Function 19
Menu Options in TV Mode 23
Channel menu 23
Picture menu 27
Sound menu 29
Time menu 30
Lock menu 33
Other menus 34
Multimedia menu 35
Text menu 35
Photo menu 36
Music menu 37
Movie menu 38
FAQ’s 40
39
Important Safety Instructions
along with the warranty card, purchase receipt and carton. The safety precautions enclosed
Usage conditions and restrictions
To prevent any injuries, the following safety precautions should be observed in the
installation, use, servicing and maintenance of equipment. Before operating this equipment,
please read this manual completely, and keep it nearby for future reference.
• Take notice of all the warnings.
• Do not use this TV near water.
• Clean only with a dry cloth.
• Do not block any of the ventilation openings.
• Install in accordance with the manufacturer’s instructions.
• Do not install near any heat sources such as radiators, heat registers, stoves, or other TV’s
• Protect the power cord from being walked on or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the TV.
•
•
with the TV.
• Unplug this TV during lightning storms or when unused for long periods of time.
• The appliance is not intended for use by persons (including children) with reduced physical,
sensory or mental capabilities, or lack of experience and knowledge, unless they have been
given supervision or instruction concerning use of the appliance by a person responsible
for their safety.
• Young children should be supervised to ensure they do not play with the appliance.
•
damaged in any way, such as power supply cord or plug is damaged, liquid has been spilled
or objects have fallen into the TV, the TV has been exposed to rain or moisture, does not
operate normally, or has been dropped.
• If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or
4
NOTE:
liquids, such as vases, shall be placed on the TV.
Important Safety Instructions
Electrical safety, power cord and plug
• Before installing this TV set, make sure your outlet voltage corresponds to the voltage
stated on the appliance rating label.
• To reduce the risk of re or electric shock, do not expose this appliance to rain or moisture.
• Do not overload the power cord or power outlet.
• Do not let the cord hang over the edge of a table or counter, or touch any hot surface.
• Do not allow anything to rest on or roll over the power cord and signal cable.
• Protect the power cord and signal cable from being trampled.
• Do not expose the power cord and signal cable to moisture.
Position
• If a television is not positioned in a suciently stable location, it can be potentially
hazardous due to falling. Many injuries, particularly to children, can be avoided by taking
simple precautions such as:
• Securely attaching the TV to the wall mount fastened on the wall.
• Only using furniture that can safely support the television.
• Ensuring the television is not overhanging the edge of the supporting furniture.
• Educating children about the dangers of climbing on furniture to reach the TV controls.
• Not standing the TV on cloth or other materials placed between the television and
supporting furniture.
• Not placing the television on tall furniture (for example, cupboards or bookcases)
without anchoring both the furniture and the television to a suitable support.
• When deciding on where to put the TV set, make sure the place is:
• Well ventilated.
• Away from damp and cold.
• Protected from overheating and away from direct sunlight.
• Away from moisture drips or splashes.
• Protected from excessive dust.
• Do not install this equipment in a conned space such as a bookcase or similar unit.
• Do not put any objects lled with liquids, such as vases, on top of the TV set.
• Do not place any naked ame sources, such as lighted candles, on top of the TV set.
5
Cleaning and maintenance
• Dust the TV set by wiping the screen and cabinet with a soft, clean cloth.
• Do not apply excessive force to the screen when cleaning.
• Do not clean the screen with water or chemical cleaners as this may damage the LCD
screen surface.
Important Safety Instructions
• Do not apply excessive force to the screen when cleaning.
• Do not clean the screen with water or chemical cleaners as this may damage the LCD
screen surface.
• Do not dismantle this product by yourself, as this may cause damage. There are no userserviceable parts contained in the TV set.
• If your TV set has been damaged, contact the after sales support line for advice or take
it to a local service centre or for inspection or repair. No liability can be accepted for any
damage caused by non-compliance with these instructions or any other improper use or
mishandling of appliance.
CAUTION: TO PREVENT THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL
6
This symbol indicates that dangerous voltage constituting a risk of
electric shock is present within this unit.
This symbol indicates that there are important operating and
maintenance instructions in the documentation accompanying this unit.
WARNING:
TO PREVENT DAMAGE WHICH MAY RESULT IN FIRE OR AN ELECTRIC SHOCK HAZARD, DO
NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
CAUTIONS: •
reduce the risk of electric shock, do not perform any servicing other than that
•
responsible for compliance could void the user’s authority to operate the
equipment.
Remote Control
The buttons on the remote control and similarly marked ones on the main unit
perform similar functions.
7
Power/Standby button
Picture mode button
Sound mode button
Multi-digits channel buttton
Signal source select button
Information display button
Volume adjusting button
Favorite program button
Electronic program guide button
Media play/pause / Teletext index button
Media stop / Teletext cancel button
Media previous / Teletext hold button
Media next / Teletext size button
Mute button
TV: RED button
Media: Goto button
TV: GREEN button
OK
INFO
FREEZE
2
5
0
0
P.MODE S.MODE
1 2 3
1
4 5 6
4
7 8 9
7 8 9
A/DTV
-/--
SOURCE
+
I/II
EPG
GOTO REPEAT
SUBTITLE
FAV
REC.LIST
X
SLEEP
MENU
EXIT
ZOOM
TXT/MIX
RC-TFG019
Remote control indicator
Sleep function button
Picture frozen button
3
6
HCLOV
A-B
Numeric buttons
Return channel button
Menu button
Navigation buttons (Up, Down, Left, Right)
Confirm button
Menu exit button
Channel select button
ATV: NICAM function button
DTV/DVD: Audio channel select button
Subtitle button
Recording buttton
TV: Display mode select button
Media: Zoom in/out button
Recording list / Teletext subpage button
Media forward / Teletext on/off / mix button
Media rewind / Teletext reveal button
TV: BLUE button
Media: A-B repeat button
TV: YELLOW button
Media: Repeat playback button
Remote Control (Cont.)
Picture mode button, setting the picture mode.
P.MODE:
Sound mode button, setting the sound mode.
S.MODE:
Press the FREEZE button to freeze the picture on the screen at current frame.
FREEZE:
Sleep button, setting TV power off time.
SLEEP:
TV channel selection button.
0,1-9:
Press to select a channel number higher than 9.
-/--:
Signal source selection button (ATV/DTV/Media/AV1/AV2/S-Video/PC/Component1/Component2/HDMI1/HDMI2).
SOURCE:
Confirm button, confirm all the changes and settings.
OK:
Press the INFO button for information.
INFO:
Press the EXIT button to exit the operation.
TV mode--Press to choose different audio languages; DVD mode--Press to choose a different audio channel.
I/II:
Press the EPG button for detailed information about the channel.
EPG:
Press the FAV button to start the “Favorite List” for selecting your favorite program.
FAV:
Press to start recording programme.
:
Press the REC.LIST button to display the recording list.
REC.LIST:
Media operation
ZOOM: Press to zoom in the picture.
SUBTITLE: Press to display current sub-title.
:
Press to play or pause the Media display.
l
: Press to move backward.
d
:
Press to move forward.
c
:
Press to stop the Media display.
n
: Press to play last item.
f
:
Press to play next item.
e
8
Press it to enter teletext state and display teletext page; press this button again, display both image and teletext page at the same time. If you
TXT/MIX:
want to exit teletext state, press this button again.
Do not display the content of the page, but only the channel image. Press it again to display the content of the page again.
CANCEL:
Press it once to enlarge the content on the upper part of the page, and press it the second time to enlarge the content on the lower part of the
SIZE:
page, and the third time to resume normal display of all the contents on the page.
SUBTITLE:
HOLD:
REVEAL:
SUBPAGE:
INDEX:
Number buttons 0~9 on the remote control can be used to get to a certain page. “ ” button on the remote control can be used to display the content
of previous or next page. Press the RED, GREEN, YELLOW & BLUE buttons on the remote control, the page of relevant color displayed on the lower
part of the screen will be displayed.
FAST TEXT: The RED, GREEN, YELLOW & BLUE buttons are used for quick access to color coded pages transmitted by FAST TEXT broadcast.
Example:
RED selects CITY INFORMATION,
GREEN selects WEATHER INFORMATION,
YELLOW selects TV PROGRAMMING,
BLUE selects TRAVEL INFORMATION.
Press the SUBTITLE button to display the subtitle function.
Press it once to keep the display of the page, and press it again to exit hold state.
Press it once to display the hide text, press it again to close the display of hide text.
It is refer to the subpage of teletext page, i.e. subcode page. When it is pressed, the screen display the requirement of subpage code
entry. If there is no subpage, it will not be displayed. In most case, there is no subpage.
Press it once to display the index for all the teletext page.
Remote Control (Cont.)
Inserting batteries
1. Open the cover at the back of the remote control unit completely.
2. Insert two 1.5V AAA batteries, ensuring the polarities (+ / -) of the batteries are correctly
aligned and the batteries are properly pushed
into place so they can power the remote control unit.
3. Slide the cover back into position.
Insert two AAA batteries.
9
NOTE: When testing the remote control unit after replacing the batteries, make sure the TV is
properly connected to the mains power supply.
Precautions when using batteries
• Do not use old and new batteries together.
• Do not use different types of battery (for example, Manganese and Alkaline batteries)
together.
• Note that there are chargeable and non-chargeable batteries. Do not attempt to charge
non-chargeable batteries.
• Remove the batteries from the remote control unit if you do not intend to use the unit for
a long time.
• When disposing used batteries, follow any guidelines for recycling and disposal of
batteries that apply in your local area.
Using the remote control
To use the remote control, point it towards the remote sensor at the front of the television.
The remote control has a range of up to approximately ve metres from the TV at an angle of
up to 30 degrees each to the right and left of the sensor. The remote control will not operate
if its path is blocked.
Accessories
The configuration of the components may look different from the following
illustration.
10
Warranty
Card
Remote
control
Batteries
Assembly
Assembling the stand
Step 1:
Place a soft, cushioned
surface to prevent damaging
the LCD screen. Then place
with the screen side facing
support column, as illustrated
on the right.
Step 2:
Use the Four supplied
screws to fasten the stand
to the support column, as
illustrated on the right.
11
NOTE: Two of these screws
are already assembled on the
connecting part to hold it in
place during transportation.
You need to take them out
before assembling the stand.
There are a total of 4 screws
to fasten the base to the TV
support column.
The stand is now fully
assembled.
Assembly (Cont.)
Wall-mounting
The television set is equipped with holes on the back panel for use with wallmounting brackets (not included). Please use the image below as a reference when
buying wall-mounting brackets.
NOTE: The distance between the holes is 300 x 200mm in width and height.
3
0
0
2
0
0
12
For wall-mounting, remove all Six screws to
remove the entire stand assembly.
NOTE: The screws in the package are for securing the TV stand only. If you are
wall-mounting the TV, consult a
installer for further instructions on
bracket support and wall support.
Controls and Connections
13
Power supply
Ensure your mains voltage and
frequency correspond with those
on the TV rating label.
General control buttons
1. Power/Stand-by button (
2. Input source select button (SOURCE)
3. Menu button (MENU)
4. Channel up button (CH
5. Channel down button (CH
6. Volume increase button (VOL+)
7. Volume decrease button (VOL- )
8. Remote sensor
9. Power indicator
Sockets (rear and side panel)
1. Audio out (L/R)
2. Component video input sockets (Y Pb/Cb Pr/Cr)
3. Antenna input socket (RF 75
4. VGA interface input socket (VGA)
5. PC audio input socket (PC AUDIO)
6. High D
7. USB port (MEDIA)
8. Headphone socket (
9. S/PDIF Coaxial output socket (COAXIAL OUT)
10. Composite video & audio input sockets (VIDEO/L/R)
ultimedia Interface input sockets (HDMI1/2/3)
)
)
)
)
)
Controls and Connections (Cont.)
AV Connection
Component (YPbPr)
14
AUDIO OUT
USB Connection
AUDIO OUT
Controls and Connections (Cont.)
VGA (PC Connection)
AUDIO OUT
NOTE (A): Only for PCs that have an audio terminal.
NOTE (B): Please refer to your computer’s documentation for instructions on how to enable
the video and sound output via these connections.
15
HDMI Connection
AUDIO OUT
Getting Started
Make sure all necessary connections are correctly made before connecting the unit to the
wall socket and turning on the power.
Powering the LCD LCD TV
• Plug the AC power cable into a suitable power point, then turn on the power at
the outlet.
• Press the POWER button on the remote control, making sure to aim it at the sensor at
the front of the TV.
First use
Before you have tuned and stored any
channels, the Installation Guide (right) will
appear on the screen when you switch on
the TV in DTV/ATV mode.
and start the channel search
Selecting an input source
You can select between the TV signal and the input signal of other equipment connected to
the TV.
Use this function to switch to the input source you wish to view.
16
SOURCE
Press the SOURCE button on the remote control.
then
Press the up/down navigation keys to move to the
desired input source.
then
Press the OK button to conrm your selection.
Basic Operation
Watching TV
1. Turn on the TV.
2. Press the SOURCE button and use the up/down navigation keys [
to select analog (ATV) or digital (DTV) as input source, then press OK.
3. Choose the channel by pressing the [Ch+] or [Ch-] or by pressing [0, 1-9]
(combined [-/--] if necessary) to input the channel number directly.
Watching a video tape
1. Turn on the TV and your VCR (which must be connected to the TV).
2. Press the SOURCE button and use the up/down navigation keys [ ]
to select the appropriate source (e.g. AV, HDMI, YPbPr); then press OK.
4. Press the PLAY button on your VCR (or its remote control).
Watching cable/pay TV
1. Turn on the TV.
2. Press the SOURCE button and use the up/down navigation keys [
select the appropriate source (e.g. AV, HDMI, YPbPr); then press OK.
3. Turn your cable broadcasting receiver (set top box) on and select the channel you wish to
view.
] to
17
]
Playing a DVD from an external DVD player
1. Turn on the TV and your DVD player (which must be connected to the TV).
2. Press the SOURCE button and use the up/down navigation keys [
3. Turn on your external DVD player, insert a DVD and press the PLAY button.
Using the TV as a PC monitor
1. Turn on the TV.
2. Press the SOURCE button and use the up/down navigation keys [
PC
NOTE: Please see Note (B) on page 15.
] to
] to
Electronic Program Guide (EPG)
EPG stands for Digital Electronic Program Guide. It is supplied by the program providers and
oers information about the programs to be broadcast. You can access it in digital mode
by pressing the EPG button on the remote control, the menu will appear on the screen, as
below:
NOTE: When the TV is rst turned on (in DTV mode), no EPG information is displayed. If still
no EPG information is displayed after you have brought up the EPG menu, use the
and
/ buttons to navigate to the channel you wish to display the information from
and when it is highlighted, press OK on the remote control to activate it.
18
/
Once you have activated a channel, use the
use the
and down the dierent timeslots.
Index
Press this button to bring up the index, press the
channel list.
Record
To record a selected program, press the RECORD button and insert an appropriate USB
device (see pages 19-22 for more on recording).
Schedule
Press the YELLOW button to bring up a schedule of programmed recordings.
Remind
Press the GREEN button and use the
button to bring up the programs to be broadcast and the / buttons to move up
/ buttons to navigate between programs.
/ buttons to go to the top row (Channel), then
/ buttons to select the time list or
Recording - PVR Function
This TV features a PVR recording and playback function which lets you:
• Instantly record a TV program (via the one-touch recording button on the remote control).
• Time-shift playback of a digital television program.
• Set a timer to record future television programs (via the EPG).
For details about these recording functions, see pages 20-22.
IMPORTANT: For any type of recording with this television, you must have inserted a USB
device into the appropriate USB port.
USB setup
PVR le system
In DTV mode, enter the Channel menu (see page
24) and select PVR File System.
19
Select the disk for storing the content you want to
record.
Check PVR le system
Select “Check PVR File System” and press OK
to check your USB device. If no USB device is
connected, a notice will advise you accordingly.
Recording - PVR Function (Cont.)
Format
If your USB device is recognised and
working, you can select Format.
Press OK to start Format (le system size).
IMPORTANT: If you select Format, all data
will be deleted!
20
Press the
Type, then press OK to format the USB
device. The Format Disk screen appears:
After formatting, the system will establish
a PVR le system according to the previous
conrmed PVR le system size.
Speed
After the PVR le system has been created and checked, an on-screen message will indicate
the available USB speed.
Storage capacity
/ keys to select PVR File System
Approximate storage capacity required when recording digital signals:
Time SD Channels HD Channels
30 minutes 1.4 GB 3.1 GB
60 minutes 2.8 GB 6.2 GB
90 minutes 4.3 GB 9.3 GB
120 minutes 5.7 GB 12.4 GB
150 minutes 7.2 GB 15.5 GB
180 minutes 8.6 GB 18.6 GB
Recording - PVR Function (Cont.)
Recording
Select “Record Start” from the Channel menu and press the OK button to start recording.
To stop recording, select Stop in the operation menu (see the bar below) and press the OK
button to operate.
NOTE: You can also press the REC button to start (and the button to stop) recording
directly.
The system can record and play back DTV at the same time. Select the appropriate action
from the panel above and press OK to operate.
This icon will be appear when you start recording.
Time-shift function
The time-shift function allows you to pause the live TV signal, then resume playback at your
convenience. While in DTV mode, press the PLAY/PAUSE button initiate time-shift mode
and pause the program. Press again to resume playback. Use the
to select a function such as Fast Forward from the on-screen toolbar. Press the EXIT button to
hide/display the on-screen toolbar. Press the STOP button to exit time-shift mode and return
to live TV signal.
NOTE: Using this function requires a formatted USB storage device be connected to the TV.
This function temporarily uses space on the attached
USB storage device, but is removed when time-shift
more is exited.
Recorded list
Display the list of recorded programs either via the Channel
menu or directly by pressing the INDEX button when in DTV
mode.
Play
Press OK to play the selected program, or press
recorded program directly. The
start playback.
Delete
Press the RED button to delete the selected program.
icon will appear when you
to play the
/ keys, then press [OK]
21
Recording - PVR Function (Cont.)
Display
Press the Display button to display or close program
information.
Record mode
Enter Record Mode via the Channel menu.
Mode: Choose from dierent recording modes: once, every
day, weekly.
Start Time: Set the date and time to start recording.
End Time: Set the date and time to end recording.
Important notes
When using the Media function, remember the following important points:
• We strongly recommend you back up all data in the USB storage device to another
storage device so you do not risk losing any data in case of an unexpected device
failure or accident. We do not assume liability for any loss of data due to misuse
or malfunction. Data backup is your personal responsibility.
• You cannot change to a channel from another broadcaster or select another function while in recording mode.
• If the signal is interrupted or removed while in recording mode, the recording will
stop until the signal is established. This may cause you to lose program content.
• Do not turn the TV off during recording, otherwise the TV will exit the PVR function
and turn to standby mode.
• The file recorded can only be used in this TV. Do not copy it to any other device.
• When you are in PVR recording mode, you may experience some difficulty with a
scheduled recording at different times without removing the USB recording device.
You will need to remove the USB device as it is required to reset after each recording to protect the device from damage. You may also see the message ‘DISK NOT
READY’ displayed. Remove the device, reconnect and proceed with your recording.
• Some USB storage devices may not be compatible for smooth operation with this TV.
• For large file sizes and large capacity storage devices, the loading speed may be longer.
• The recognition speed of a USB storage device may vary depending on the device.
• When connecting or disconnecting the USB storage device, ensure the TV is not in
Media mode, otherwise the USB device or the files stored in it may be damaged.
• Only use a USB storage device formatted in a FAT32 file system provided with the
Windows operating system. If it is formatted by a different utility program that is
not supported by Windows, it may not be recognised.
• Ensure any USB devices connected to the TV do not use/exceed 500mA power rating.
• An “Unsupported File” message will be displayed if the file format or codec is unsup-
ported or corrupted. (Refer to specifications table on page 40 for supported file types.)
22
Menu Options in TV Mode
1. Press the MENU button on the remote control, the on-screen menu will appear on the
screen.
2. Use the left and right navigation keys to select your main option.
The main menu items, from left to right, are:
Channel Picture Sound Time Option Lock
Channel menu
23
From the Channel menu you can search channels, either automatically or manually, and set
up a variety of channel options.
NOTE: You can only select the Channel menu in ATV/DTV mode.
NOTE: All default settings have been selected for Australia.
Menu Options in TV Mode (Cont.)
Auto scan
In the Auto Scan submenu you can select your country and the tune type: DTV+ATV, DTV
only and ATV only.
Press
/ / / to make your selection, then press OK to start scanning.
When DTV+ATV is selected, half the scanning is for analog TV channels and the other half for
digital channels.
24
When ATV tuning, you can press EXIT to skip ATV tuning and start DTV tuning, as below:
Menu Options in TV Mode (Cont.)
DTV manual tuning
1. Use the left/right navigation keys to select a channel, then press OK to conrm if any
signal strength shows.
2. Press OK to conrm tuning (only in DTV mode).
ATV manual tuning
25
Storage To: Select a position (from 1 to 100) to store the channel.
System: Default option depends on country selection, you can select BG, DK, I and L. Select
BG for Australia.
Current CH: Select a channel (from 1 to 100) you want to tune.
Search: Use the arrow keys to commence the search.
Fine-Tune: Select to ne-tune manually.
Frequency: Displays the current frequency following searching or ne-tuning.
NOTE: After manual tuning you must press the red key for storage, otherwise your tuned
channels will not be stored when changing the mode.
Menu Options in TV Mode (Cont.)
Program edit
26
Encryption
Identity
S 21 ABC1
In the Program Edit submenu, you have various options for setting up your channels,
including Delete, Move, Rename, Skip, Lock and Favourite.
NOTE: Skip and Favourite cannot be used together.
DELETE: Press the RED button to delete the current channel.
RENAME: Press the GREEN button to modify the current channel name (ATV only).
MOVE: Press the YELLOW button to move the position of the channel. (ATV only).
SKIP: Select a channel and press the BLUE button to skip that channel when scanning
channels with the CH+/- button.
FAV: Select a channel and press the FAV button to set it as a favourite channel.
Signal information
In DTV mode, this shows signal information including channel, network, modulation, quality
and strength.
Record Start: Select this to start recording the current channel.
Recorded List: Select this to display a list of recorded programs.
Recorded Mode: Select this to schedule a recording for a future time and date.
Schedule List: Select this to display the list of Scheduled Recordings and Reminders.
PVR File System: Select to enter the PVR File System setup menu. Refer to ‘USB Setup’ on
LCN
page 19.
CH
Name
Skip
Identity
Lock
Identity
Fav
Identity
System
Menu Options in TV Mode (Cont.)
Picture menu
27
Picture mode
Change the picture display mode with the right/left
Standard, Mild, User and Dynamic modes.
IMPORTANT NOTES
You need to set Picture Mode to User to be able to adjust contrast, brightness, colour and
sharpness.
The tint value can only be adjusted in NTSC signal.
/ navigation keys. You can select from
Menu Options in TV Mode (Cont.)
Contrast / Brightness / Colour / Sharpness / Tint
Use the / keys to switch between contrast, brightness, colour and sharpness, then use the
/ keys to adjust the values.
Colour temperature
Use the / keys to adjust the value, you can select Medium, Cool, Warm or User.
Red / Green / Blue
28
Use the / keys to switch between red, green and blue, then use the / keys to adjust the
value.
Aspect Ratio
Use the
ZOOM2, Just Scan, Auto and 4:3.
Noise reduction
Use the
Screen
Use the
NOTE: The ‘Screen’ menu can only be selected when ‘PC’ input/source has been selected and
/ keys to select your desired aspect ratio, you can choose from 16:9, ZOOM1,
/ keys to select from Low, Middle, High or O.
/ keys to switch between items, then use the / keys to adjust the values.
a signal connected to the VGA socket.
Menu Options in TV Mode (Cont.)
Sound menu
Sound mode
Use the
User.
NOTE: You can select treble, bass, balance. To adjust the setting, change the mode turn to
Treble/ Bass/ Balance
/ keys to change modes, you can select from Standard, Music, Movie, Sports or
user automatically
29
Use the
Auto volume
When set to “On”, the volume of the channel is automatically controlled.
Surround sound
Choose to turn the surround sound “On” or “O”.
SPDIF Mode
Use the
/ keys to switch between treble, bass and balance, then use the
/ keys to adjust the value.
/ keys to select your desired output. You can select from Auto, PCM or O.
Menu Options in TV Mode (Cont.)
Time menu
Clock
Use the
NOTE: You cannot change the time manually in DTV mode, as the time comes directly from a
/ keys to select Clock, then use the / keys to set the time.
signal source.
30
frequency.
Repeat options
Sunday.
Hour/Minute
To change the time, use the / keys to select this option, then use the / keys to adjust
the time.
Menu Options in TV Mode (Cont.)
On time
You can set the time when the TV set will be turned on automatically, you can also set the
frequency, volume and program.
Repeat options
Sunday.
Hour/Minute
To change the time, use the
the time.
Volume / Source / Channel
Use the
NOTE: To select a channel, choose ATV/DTV as source.
Sleep timer
20, 30, 60, 90, 120, 180 or 240 minutes.
Auto sleep
minutes when there is no signal.
/ keys to adjust the volume, source or channel.
/ keys to select this option, then use the / keys to adjust
31
Time zone
Select your state of residency for the correct time.
Daylight Saving
Menu Options in TV Mode (Cont.)
Option menu
Restore Fectory Default
OSD language
Use the
Audio language 1st/2nd
Use the
(in DTV mode only).
Subtitle language 1st/2nd
Use the
language (in DTV mode only).
OSD duration
Use the
messages.
Country
This displays the country selected during the rst use of TV. It should only be set to ‘Australia’.
This can only be changed by performing the ‘Restore Factory Default’ option below.
/ keys to select this option, then select your preferred on-screen display language.
/ keys to select this option, then select your preferred 1st and 2nd audio language
/ keys to select this option, then select your preferred 1st and 2nd subtitle
/ keys to select this option, then set your preferred duration for on-screen display
32
Restore factory default
Use the
NOTE: All your picture, sound, time and option settings will be lost when restoring
/ keys to select this option to restore factory default settings.
factory defaults.
Menu Options in TV Mode (Cont.)
Lock menu
Lock channel
33
manually search and adjust channels. To change this setting, you must enter a password: the
default password is “0000”.
Set password
match” will appear on the screen. Press the
Press the
Block program
Enter the submenu, select a channel and press the GREEN key to block it. Check to make sure it is
blocked. To watch a blocked channel, enter the password.
Parental guidance
Choose from the following parental control levels: Block R and Above, Block AV and Above,
Block MA and Above, Block M and Above, Block PG and Above, Block G and Above,
Block C and Above, Block P and Above, Block ALL and No Block.
NOTE: If you forget your password, enter the master password “4711” to reset.
key to cancel your password and to set a new one.
key to exit and go back to main menu.
Menu Options in TV Mode (Cont.)
Hotel Setting
Allows you to Enable and Disable various features of the TV.
Hotel Lock: Enable or Disable the feature
Lock Channel: Enable or Disable access to the Channel Menu
Set Source: Set the default Input Source
Channel Number : Use with Set Source options
Picture Lock: Enable or Disable access to the Picture Menu
Key Lock: Enable or Disable buttons on TV
Max Volume: Set the maximum selectable volume level
Source Lock: Enable or Disable the various Sources such as HDMI, AV, etc.
Clear Lock: Restore all Hotel Settings to default.
Other menus
Channel list
Press the OK button on the remote control to display the list of all tuned channels, as
below:
34
Favourite list
Press the FAV button on the remote control to display your list of favourite channels.
35
Menu Options in TV Mode (Cont.)
Multimedia menus
Press the SOURCE button on the remote control, then choose USB to enter multimedia mode.
Make sure you have an appropriate USB device connected.
Your options are as below, from left to right:
PHOTO MUSIC MOVIE TEXT
Use the
/ buttons to select your option and press OK to enter the submenu.
Text menu
In the Text menu, your chosen text le and details will be displayed in a preview frame. Press
OK [Play] to enter full screen text mode.
Menu Options in TV Mode (Cont.)
Photo menu
In the Photo menu, your chosen picture and details will be displayed in a preview frame.
Press OK to display it in full screen mode, press OK again for more options, as below:
36
Repeat: Press OK and choose between three repeat modes: Repeat 1, Repeat All, Repeat
none.
Music: Press OK to play background music.
Playlist: Press OK to display a playlist.
Info: Press OK to display the information about the picture.
Rotate: Press OK to rotate the picture. One option rotates the picture in a clockwise direction,
the other option rotates it anti-clockwise.
Zoom Out/In: Press OK to zoom out of the picture, or choose the other option to zoom in on
the picture.
Menu Options in TV Mode (Cont.)
Music menu
In the Music menu, your chosen music le and details will be displayed in a preview frame.
Press OK to enter full screen music mode. Music will be played back just like on a PC with the
appropriate software. There is a playlist, basic information, processing sign, operation guide
part, as below:
37
Repeat: Choose between Repeat 1, Repeat All, Repeat none.
Go To: It rst displays as 00:00:00/01:23:45. Use the
and the / buttons to adjust the numbers.
/ buttons to move between positions
Menu Options in TV Mode (Cont.)
Movie menu
In the Movie menu, your movie will be displayed in a preview frame. Press OK to display it in
full screen mode, press OK again for more options, as below:
38
Repeat: Choose between Repeat 1, Repeat All, Repeat none.
Set A: Choose this function to repeat playback of a certain section (A-B).
Playlist: Press OK to display the playlist.
Info: Press OK to display the information about the movie.
Slow forward: Press OK to play the movie/go forward with slow speed.
Step forward: Press OK to play the movie/go forward in steps.
Go To: It rst displays as 00:00:00/01:23:45. Use the
and the / buttons to adjust the numbers.
Zoom In/Out: Press OK to zoom out of the display, or to zoom in on it.
Move View: Use this to move the display if the movie is too big for the screen.
/ buttons to move between positions
Specifications
Model KALCD39FHDXA
Panel system 99cm (39”) FHD LCD panel
Display resolution 1920 x 1080
Television system HD DVB-T, PAL DK/BG/I, SECAM DK/BG
Inputs/outputs
ATV/DTV(RF 75Ω) 1
CVBS input/audio(L/R) 1
HDMI input 3
YPbPr input 1
VGA input 1
PC audio input 1
USB 1
Storage Multimedia format support
MOVIE MPEG2 AVI, MP4, DIVX4, DIVX5, XVID
(max. resolution 720×576 pixel, max.
baud rate 6Mbps)
MPEG1/2 MPG, MPEG, VOB, DAT, TS
(max. baud rate 9.8Mbps)
PHOTO BMP, JPG,
PNG
MUSIC MP3 32K-320K
SPDIF output 1 (Coaxial)
Audio output (L/R) 1
OSD language English, German, French, Italian, Spanish
Speaker power 2×10W
Power supply 100-240 VAC, 50/60Hz
Power consumption <120W
Power standby <1W
Universal remote control NEC 027D
Dimensions (W x H x D, mm) 912 x 617 x 260 (with stand)
912 x 560 x 111 (without stand)
Weight (net) - TV only 11.9kg
BMP, JPG
(max. resolution 3000×3000 pixel)
PNG
(max. resolution 1000×1000 pixel)
39
FAQs
Problem Action
The screen does not appear/
illuminate.
The screen appears too
slowly after the power is
turned on.
The screen is too bright or too
dark.
The screen is too large or too
small.
Stripes appear on the
screen and it shakes.
Access to the programs is
blocked.
The screen appears, but
there is no sound.
The remote control does
not work.
1. Check that the power is on.
2. Check that you have not pressed the BLUE
button and switched OFF power to the screen.
This problem occurs only briefly in the process of
image elimination processing, which is necessary
for hiding temporary screen noise that occurs
when the power is turned on. If the screen
does not turn on after one minute, contact our
customer after sales support line.
Check the brightness and/or contrast
adjustments.
Adjust the screen size by selecting the zoom button.
Stop using wireless telephones, hair dryers or
other electrical appliances near the TV.
Check that you have not changed the access code
or password. To reset, please enter the following
master password “4711”.
1. Press the MUTE button.
2. Increase the sound level by pressing the
volume adjustment button.
3. Check that the sound terminal of your external
input is connected properly.
4. Check that the audio cables are connected properly.
5. Select and check any other input.
If the sound still does not work and the other
channels are the same after you have checked the
above points, contact the after sales support line.
1. Check if the main power is switched on.
2. Check that the batteries of the remote control
are loaded properly.
3. Check for any obstacles between the LCD
TV and the remote control and remove them, if
necessary.
4. If the batteries have no power, replace them
with two new batteries of the same type.
40
Notes
41
Loading...