Page 1
Page 2
SAFETY NOTICES
To avoid electric shock, fire or unit malfunction, please read and follow the
following instructions.
1. Never disassemble the unit yourself. There are no user serviceable parts
inside.
2. If the supply cord is damaged, it must be replaced by a Kogan customer
service technician, or similarly qualified persons in order to avoid a hazard.
3. Do not use 3rd party attachments with this equipment, as it may cause
damage.
4. If there is any abnormal smell during normal operation, please switch off
and disconnect power supply, then contact the Kogan customer service
team.
5. Always turn unit off and unplug it prior to removing, filling or emptying the
water tank.
6. Do not add third party detergents or chemical solutions into the unit.
7. Keep detergents and chemical solutions away children.
8. If detergents or chemical solutions splash into mouth & eyes during
cleaning, rinse well and thoroughly with water and consult a doctor
immediately.
9. Never touch water in the water basin or components in the water when the
unit is working.
10. Never switch on when there is no water in the water basin.
11. Never touch the transducer.
12. Never clean the transducer with detergents or chemical solutions that are
not recommended by the Kogan sales team.
13. Never let water splash into inner base unit when cleaning, to avoid
component damage.
14. Never move the machine with the tank full of water.
15. Position the unit on an even surface, and keep the machine at least 2
meters away from furniture and other electrical appliances.
16. Care should be taken due to the possible emission of hot vapors.
17. This appliance is not intended for use by persons (including children) with
reduced physical, sensory or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or instruction
concerning use of the appliance by a person responsible for their safety.
18. Children should be supervised to ensure that they do not play with the
appliance.
19. Only use water in the tank, never use any additive such as essential oils, etc.
into the water.
Page 3
PRODUCT LAYOUT
OPERATION
Prior to first operation, place the unit into location at room temperature for half
an hour before running. (This is especially important when the outdoor
temperature is below 5°C).
It is recommended that you use this product is temperatures between 5 ~ 40°C,
when the relative humidity is less than 80%RH.
Use clean, clear water that is not above 40°C.
Check the water basin each time to ensure that it is clear.
• Take the water tank (3) out of the base (14), then remove the valve cap (7).
Fill the water tank (3) with clean water, then close the valve cap (7) and
put the water tank (7) back onto the base (14).
• Put the nozzle (1) into the socket on top of the water tank (3).
• Connect the power cord (18) to the mains power supply. The machine will
now be in standby mode. NOTE: Never run the unit when there is no water
in the water tank.
• Switch the unit on be pressing ON (15). The blue power LED will then
illuminate. The unit will operate with the lowest mist output, while also
using the fan motor. When unit is OFF, all functions except the ANION are
not valid and the blue power LED will not be lit.
Steps
Page 4
Settings
ION: When the unit is in standby mode, pressing the ION button will put the unit
into humidifying mode. The fan motor will come on at the same time. (If unit is
not humidifying and the ION setting is off, the fan motor will not work.)
TIMER: Settings repeat from 0-2-8-12 hours.
MIST: There are 4 levels, from Low, Middle, Senior and High for different mist
outputs. The corresponding power levels are 13-16W (L), 17-20W (M), 21-24W (S)
and 26-30W (H).
Waterless protection: when the tank is out of water, the Waterless indicator lamp
will illuminate and the unit will stop. At this time, any preset TIMER and
HUMIDISTAT settings will be cancelled. Once the tank has been refilled with
water, it will reset the functions.
TROUBLESHOOTING
Please refer to the following table for any issues that may arise. If the problems
persist, please contact the Kogan customer support team.
Issue Possible Reason Possible Solution
LED display is off. No power supply Connect power supply
Unit not turned ON Switch on
LED display is on. No mist and no
air output
No water in water tank Fill water tank
Too much water in the water tank Remove some water from the
tank, then close the cover of the
tank tightly
LED display is on. Unit has water
but the waterless protection has
triggered
Floater is stuck Manually move the floater with
your hand so it floats freely
Abnormal smelling mist New unit Take water tank out, open cover
and let sit for 12 hours in a cool
location
Dirty or old water Pour out water, clean tank and
then refill
Not enough mist/fog Too much scale in the water Clean the transducer
Water is too dirty or old Pour out water, clean tank and
then refill
Water is too cold Add some warmer water
Abnormal noise Resonant sound in water tank
when water is low
Fill tank with water
Unit is on an unstable surface Move unit to a stable, flat surface
Mist coming out around the nozzle There are gaps between nozzle
and water tank
Dip nozzle into water, then fix it to
the socket on the water tank
Water doesn't come down into
basin
Blocked filter Rinse filter under tap water
Display shows HF or LF Poor contact for humidistat sensor Reinstall sensor
There is water in sensor Disassemble unit and allow to dry
in a cool, well ventilated area
Page 5
MAINTENANCE
In cases where the water supply is “hard” (meaning that the water contains too
much calcium and magnesium), it can cause water scale on the surface of the
water basin, transducer and inner surface of the water tank.
Scales on the surface of the transducer will reduce the units ability to work
properly.
We recommend that you:
• Use cold boiled water, or distilled water
• Clean the transducer and water tank every week
• Change the water in the tank often to keep it fresh
• Make sure to remove the water from the water tank and let the unit dry
thoroughly before storing the unit for any period of time
• Clean the whole unit and makes sure that all parts of the unit are dried
thoroughly before laving the unit unused for a long period of time
• Do not use any chemicals for cleaning
How to clean the transducer
1. Put 5-10 drops of an ultra-mild cleaning detergent on the surface of the
transducer and wait for 2-5 minutes
2. Brush the scale off the surface
3. Rinse the transducer with clean water
How to clean the basin unit
• Clean the water basin with a soft cloth and mild detergent if there is scale
in it
• If the scale is covering the security switch, cover the scale with the
detergent, then clean it with the brush
• Rinse the basin out with clean water afterwards
TECHNICAL DATA
Model KAHUM58IONA
Standard output 300ml/H
Water tank volume 5.8 Litres
Noise level < 35dB (A)
Rated voltage 220-240V
Frequency 50Hz
Rated power input 30W
N.W / G.W 1.6kg / 2.2kg
Disposal
Do not dispose of this product as unsorted municipal waste with your
household garbage. Contact your local council for advice on how to
dispose of electrical equipment.
Loading...