Kogan KACRDWFLBKA, KACRDWFLWHA, KACDWFWHR4A, KACDWFBKR4A User Manual

CORDLESS ADVANCED WATER
FLOSSER

KACRDWFLBKA & KACRDWFLWHA

SAFETY & WARNINGS

Note: There may already be liquid in the water tank of the flosser. This is the distilled

water remaining during the factory inspection. There is no hazard for health and
safety.

• If you have had oral or dental surgery in the past 2 months, consult your doctor
before using this flosser.

• When using this flosser for oral cleaning for the first time, you may experience
minor gum bleeding even under the case of healthy gums. This is because your
gums are stimulated by the jet pressure for the first time. It will stop bleeding after
1-2 weeks. If your gum bleeding lasts for more than 2 weeks, stop using the flosser
and consult your dentist.

• Do not use this flosser if the USB cable or plug is damaged. Ensure the USB cable
is not damaged before and after usage. Keep the USB cable away from heated
surfaces.

• Do not connect to a charger which does not have the rated voltage. See the
Specifications section.

• The flosser's charging port has a silicon cover to protect it from water or liquids.
Ensure there is no residual liquid in the port before charging.

• This flosser is not intended for use by persons (including children) with reduced
physical, sensory or metal capabilities or lack of experience and knowledge, unless
they have been given supervision or instruction concerning use of the flosser in a
safe way by the person responsible for their safety, and understand the hazards
involved.

• Do not use this flosser to inject water into ears, nose, bottom of your tongue or
other sensitive body parts. The pressure generated by this flosser may cause
serious damages.

• Do not disassemble or repair this flosser.

• This flosser’s jet tip can be replaced. Use correct replacement jet tips by

Kogan.com. See the Cleaning and Care section.

• Do not put or insert any strange objects into the flosser.

• Do not touch the flosser’s power supply while charging. Do not charge it in a moist

• environment. Failure to follow these instructions could result in electric shock or

damage to the flosser.

• Do not place or store the flosser where it may fall or be pulled into a bathtub,
shower, or sink.

• The flosser can only be filled with water. Consult dentist before filling it with other
non-corrosive liquid.

Jet Tips (x2)

USB Cable (x1)

LED Lights

Jet Tip Lock/Unlock Button

On/Off Switch

Jet Tip

Mode Button

Normal

Soft

Charging Indicator Light

DIY

Pulse

Water Tank

Pull out

Retractable

Note: The water tank is detachable and can be removed for filling water.

1. Ensure to charge the device before using for the first time.

2. Open the water inlet of the Water Tank and fill it with water. Close the inlet
window of the tank and press tightly.

Do not power on the flosser when the tank is removed.

3. Insert the Jet Tip into the top head socket. To replace or remove the Jet Tip, press
the Jet Tip Lock/Unlock Button.

4. Press the On/Off Button for 3 seconds to turn on the flosser. Press the Mode
button to select the working mode.

5. Press the Mode button on the handle to select the appropriate cleaning mode for
the first-time use. You can also choose the cleaning mode according to your
dentist guidance.

Normal mode

Soft mode This provides gentle massage to gums.

Pulse mode

DIY

This is a standard cleaning mode. It can
effectively remove the food residue in the
gaps between your teeth. Deeply clean teeth.
Keep the mouth fresh.

This provides pulse massage to gums and
promotes blood circulation.

In this mode, you can customise the cleaning
intensity according to your personal
preference and set various cleaning strengths
within the range

Charging the Flosser

Fully Pulled

Half Pulled

Unpulled

1. Charge the flosser for 8 hours before the first-time use.

2. Connect the USB cable to any appropriate USB adapter (5V, 1A) or USB port.

3. Plug another side of the USB cable into the charger and then plug the charger into
a power socket.

4. When charging, the Charging Indicator Lights are red and are slowly flashing.
When fully charged, the charging indicator will turn green and will remain the
same until the charger is removed.

Using Water Tank

• Pull the inner water tank until you see the “OK” mark. Now you can fill the water to
100%.

• Do not push back the inner water tank if the water tank is overflowing.

• Do not push back the inner water tank if the flosser is powered on.

• Do not push back the inner water tank if water is not used up in the water tank.

Follow the below instructions:

1. Pull the inner water tank until you see the “OK” mark.

2. Open the water inlet cover to fill water into the water tank.

3. Press On/Off button to turn on the flosser and to use it. Once completed, press the
button again to turn off the flosser.

4. Open inner water tank and pour out the unused water. Turn the main body to right

Note: Do not push or pull the water tank when using and if there is water

and water tank to left to open. Attach the inner water tank back to the main body.

5. Turn on the flosser and keep it idle for 5 seconds to drain the residual water from
the main body.

6. Push back the inner water tank.

inside.

Checking Battery Volume

1. When the product is in standby, long-press the Mode button to show the battery
volume.

2. If the battery volume is above 75%, all mode lights will be bright.

3. If the battery volume is 50% -75%, Soft, Pulse, DIY mode lights will be bright.

4. If the battery volume is 25%-50%, Pulse DIY mode lights will be bright.

5. If the battery volume is below 25%, only DIY mode light will be bright.

DIY Mode Setting

Notes:

When you switch to the DIY mode, the flosser will in the last used DIY mode status. To
change the working status of the DIY mode, follow the below instructions:

1. In the DIY mode work, press the On/Off button again.

2. The working status will rise from the lowest water pressure to the highest water
pressure mode and stay at the highest water pressure mode temporarily. The
water will circulate according to this mode.

3. Release the On/Off Button to indicate the selection of the new working status
(new status is locked). The system maintains and work under the new working
status.

First-time Usage Recommendations

When you use the flosser for the first time or after a long time, follow the below instructions:

1. Press the On/Off button and wait for a few minutes for the Jet Tip to discharge
water. Turn off the flosser,

2. Pull the inner water tank until you see the “OK” mark and also hear a “click” sound.
This indicates the inner water tank has been pulled to the right position. If not,
water will leak from the inner water tank.

3. Open the water inlet cover to fill water into the water tank.

4. After adding an adequate amount of water into the tank, push the inner water
tank back. Press On/Off button to turn on the flosser.

• When using for the first time, ensure the flosser is set to Soft
mode.

• Point the jet tip towards the gap between your teeth.

CLEANING & CARE

• Never immerse the entire flosser into any liquid.

• Unplug the power cord before cleaning.

Water Tank

• The water tank can be washed with soapy water or placed on the top dish rack of
the dishwasher.

• Always drain and dry the water in the tank before exposing it to a freezing
environment.

• Remove the dirt with a brush or similar item and then clean it with a cloth.

• When the water tank is not used for a long time, clean it well before using it again.

Jet Tips

• Press the Jet Tip Lock/Unlock button to remove the jet tip. Clean it with water and
wipe it with a cloth.

• It is recommended to replace the new jet tip every 3 months. Otherwise, the jet tip
will become too large to effectively clean the teeth.

• Following jet tips available from Kogan.com can be used as a replacement:

o For the Cordless Advanced Water Flosser – Black (KACRDWFLBKA), use

KACDWFBKR4A.

o For the Cordless Advanced Water Flosser – White (KACRDWFLWHA),

use KACDWFWHR4A.

Main Body

Remove the dirt with a dampened cloth and a mild detergent. Then wipe it with a dry cloth.
If it is very dirty, it can be washed with water.

• Do not use alcohol, benzene, thinner, etc to wipe the product.

• Do not wash with hot water above 50°C.

• Wipe off the water after cleaning suction pipe.

• Wipe with a cloth after cleaning.

• Do not bend the suction pipe. Otherwise, it may stop water absorption while the

flosser is working.

• Clean the filter net of the suction pipe in time to prevent clogging. Water Tank
Cover.

• Remove the dirt, otherwise it will cause water leakage.

Battery Voltage

3.7 V

Problems

Reason

Method of handling

Jet tip is damaged

Severe nozzle damage.

Replace the jet tip.

Water or other liquid is left in
the water tank.

The water tank cover is not
closed.

Make sure to empty the
water tank after use.

Contact Kogan.com to
replace the seal.

Water is leaking from the jet
tip and its socket

The jet tip is not properly
installed.

Remove the jet tip and
reinstall.

The jet tip must be above
the water tank.

Fill the tank with sufficient

section of this user guide.

Select the appropriate

section of this user guide.

TROUBLESHOOTING

Water tank is leaking

The seal is damaged.

Flosser is inverted.

Close the water tank cover.

No water flow or insufficient
pressure

Power Input AC 5V 1A

Battery Capacity 2000 mAh

Insufficient water in the
tank.

Wrong working mode.

water. See the Operation

mode. See the Operation

Need more information?

We hope that this user guide has given you

the assistance needed for a simple set-up.

For the most up-to-date guide for your product,

as well as any additional assistance you may require,

head online to help.kogan.com