IMPORTANT SAFEGUARDS
Before using the electrical appliance, the following basic precautions should always
be followed including the following:
1. Read all instructions.
2. Before using check that the voltage power corresponds to the one shown on the
appliance nameplate.
3. To protect against electric shock, do not put motor unit into water or other liquid.
4. Do not operate any appliance with a damaged cord or plug or after the appliance
malfunctions, or is dropped or damaged in any manner. Contact the Kogan customer
support team for examination, repair or electrical or mechanical adjustment.
5. Unplug from outlet when not in use, before putting on or taking off parts, and
before cleaning.
6. Do not let cord hang over edge of table or counter.
7. Do not let the power cord contact any hot surfaces, including stove-tops, toasters or
hot saucepans.
9. Close supervision is necessary when your appliance is being used near children or
infirm persons.
8. Ensure fingers are kept well away from moving parts.
9. Blades are sharp. Handle carefully.
11. Keep hands and utensils out of container while blending to reduce the risk of
severe injury to persons or damage to the blender. A scraper may be used but ONLY
when the blender is not running.
12. To reduce the risk of injury, never place cutting blade on base without first putting
bowl properly in place.
13. Always operate blender with cover in place.
14. Do not blend hot liquids.
15. Be sure chopping cover is securely locked in place before operating appliance.
16. Avoid contact with moving parts.
17. This appliance is not intended for used by persons (including children) with
reduced physical, sensory or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or instruction concerning use of
the appliances by a person responsible for their safety.
18. Children should be supervised to ensure that they do not play with the appliance.
19. Ensure that the blender is switched off before removing it from the stand.
20. If the supply cord is damaged, it must be replaced by a Kogan technician in order
to avoid a hazard. Any repairs by another repair company will void the warranty and
Kogan will not be responsible for any issues which may arise.
21. The use of accessory not recommended or sold by the manufacturer may cause
fire, electric shock or injury.
22. The appliance can not be used for blending hard and dry substances; otherwise the
blades could be blunted or damaged.
23. Do not operate the appliance for anything other than its intended use.
24. Do not use outdoors.
KNOW YOUR BLENDER
Attachments
Before your first use:
Check that the accessories are complete and the unit is not damaged. Then pour a little
water into the big cup and mix according to the steps below for one or two times, and
then pour out. Cleaning the Cup and the cup support assembly thoroughly with warm
water.
When using the jar with handle and (or) filter, clean them with same method as above.
Warning: the blade is sharp, handle it very carefully.
Note: The big cup and jar with handle are used to make juice; Furthermore, when
used with assembly filters, the jar with handle is used to make fresh soy-milk, or
separate residue, etc.
The small cup is used for milling coffee beans or small grain food.
Using the blender
1. Place the motor unit on a flat surface; make sure the power outlet is unplugged.
2. When using the big cup and jar, it must be noted that you should peel or core the
fruit or vegetables, and then cut them into small dices. When using the small cup,
the volume of food that is being prepared for juicing should not be too large.
Note: never use boiling liquids or run the appliance empty.
3. Upend the big cup (or small cup), put the prepared food into the cup. When
making juice, it is required that a certain amount of clean water should be added to
facilitate the smooth running of the appliance.
Note: a. the amount of mixture should not exceed the MAX marking (0.4L) on the big
cup;
b. The milled food in the small cup should not exceed the MAX capacity of
small cup (60g);
c. The amount of mixture should not exceed the MAX marking (0.75L) on the
jar
4. Select corresponding cup support. The big cup and jar use the cup support with
blending blade (see fig.1), the small cup use the cup support with grinding blade
(see fig.2). Tighten the cup support on the cup or jar by turning the cup support
clockwise.
5: When using jar with handle, you need to tighten the cup support first, then put the
prepared food into the jar. Then insert them into the motor unit, making sure the three
fasteners on the bottom cup support align with the grooves on the motor unit. Tighten
them by turning the jar clockwise.(see fig 3)
Cup support
Blending blade
Jar
6. Upend the assembly of cup and cup support, and insert them into the motor unit,
making sure the three fasteners on the bottom cup support align with the grooves on
the motor unit. Then tighten them by turning the big cup or small cup clockwise (see
fig.3).
7. If using the jar with handle, assemble jar cover and measure cup on it. If you want
to extract juice or make soy-milk, assemble the filter before put ingredients into the
jar. If want to accelerate the blending, using the blending rod ( see fig 4)
Note: When make soy milk, the amount of mixture should not exceed the MAX marking
(0.75L). Soybeans need be soaked in water for at least 4 hours prior to being processed.
Operate 5 cycles continuously with 3min ON, then 1 min OFF. The volume of soybeans that
are used for making soybean milk should not be more than one measure cup provided.
Fig. 3
Fig. 4
8. Connect the plug to wall outlet and the appliance will start operating.
Note: Do not run the appliance for more than 3 minutes per time. A minimum of 3
minutes rest period is required between two consecutive cycles.
9. When the operation is finished, turn the big cup, small cup or jar in an anticlockwise direction to remove them and the appliance will stop operating.
10. Upend the big cup or small cup, hand the cup with one hand, and turning the cover
in anti-clockwise with the other hand.
11. Then select suitable cover: if you used the big cup, cover the full opened cover
and serve (see fig.5). If you used the small cup, select suitable cover (with big
whole or small hole) according to you desired (see fig.6). If you do not sever
immediately, please cover the full closed cover to prevent from splashing when
the cup is overturning (see fig.7)
Note: Cover the desired cover by turning the cover in clockwise.
Fig. 5 Fig. 6 Fig. 7
CLEANING AND MAINTENANCE
The Auto Clean feature can clean the blender and blade assembly easily, rapidly and
in complete safety.
-Pour a little warm soapy water into the big cup or small cup and mix for a few
seconds by plugging in the power outlet.
- Remove the cup by turning it anti-clockwise and then rinse under running water.
-Wipe the outer surface of Motor Unit with a damp cloth.
Warning: Do not use abrasive cleaners and NEVER immerse the
Motor Unit in water for cleaning
-Dry all parts and then store them safely away from children.
For complete cleaning, you can hold the blade assembly at the bottom of cup support
carefully, taking extreme care as it is very sharp. Take it out by turning the coupling
on the underside clockwise. Then you can put the Cover, Cup and blade assembly into
the dishwasher for cleaning, as they are all dishwasher safe components. Ensure that
during the wash cycle, the temp setting does not exceed 70℃.
If any problem has been encountered during use never disassemble the Motor Unit by
yourself, no user serviceable parts inside. Contact only the authorized service facility
for examination and repair.
ENVIRONMENT FRIENDLY DISPOSAL
You can help protect the environment!
Please remember to respect the local regulations: hand in any
non-working electrical equipment to an appropriate waste
disposal centre.
Loading...