Kodo Pro KNS-1108FT, KNS-1108V3, KNS-1108FT/V3 User Manual

Download

INSTALLATION / OPERATION

USER’S MANUAL

KNS-1108FT/V3

X18 HD Megapixel Speed Dome Network Camera www.kodobr.com.br

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. DO NOT INSERT ANY METALLIC OBJECTS THROUGH THE VENTILATION GRILLS OR OTHER OPENINGS ON THE EQUIPMENT.

CAUTION

RISK OF ELECTRNIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK).

NO USER-SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

EXPLANATION OF GRAPHICAL SYMBOLS

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The e

xclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.

PRECAUTIONS

Safety ---------------------------------- Installation -----------------------------

Cleaning ----------------------------------

Should any liquid or solid object fall into the cabinet, unplug the unit and have it checked by the qualified personnel before operating it any further.

Unplug the unit from the wall outlet if it is not going to be used for several days or more. To disconnect the cord, pull it out by the plug. Never pull the cord itself.

Allow adequate air circulation to prevent internal heat build-up. Do not place the unit on surfaces (rugs, blankets, etc.) or near materials(curtains, draperies) that may block the ventilation holes.

Height and vertical linearity controls located at the rear panel are for special adjustments by qualified personnel only.

Do not install the unit in an extremely hot or humid place or in a place subject to excessive dust, mechanical vibration.

The unit is not designed to be waterproof. Exposure to rain or water may damage the unit.

Clean the unit with a slightly damp soft cloth. Use a mild household detergent. Never use strong solvents such as thinner or benzene as they might damage the finish of the unit.

Retain the original carton and packing materials for safe transport of this unit in the future.

FCC COMPLIANCE STATEMENT

FCC INFORMATION: THIS EQUIPMENT HAS BEEN TESTED AND FOUND TO

COMPLY WITH THE LIMITS FOR A CLASS A DIGITAL DEVICE, PURSUANT TO PART 15 OF THE FCC

RULES. THESE LIMITS ARE DESIGNED TO PROVIDE REASONABLE PROTECTION AGAINST

HARMFUL INTERFERENCE WHEN THE EQUIPMENT IS OPERATED IN A COMMERCIAL

ENVIRONMENT. THIS EQUIPMENT GENERATES, USES, AND CAN RADIATE RADIO FREQUENCY

ENERGY AND IF NOT INSTALLED AND USED IN ACCORDANCE WITH THE INSTRUCTION MANUAL,

MAY CAUSE HARMFUL INTERFERENCE TO RADIO COMMUNICATIONS. OPERATION OF THIS

EQUIPMENT IN A RESIDENTIAL AREA IS LIKELY TO CAUSE HARMFUL INTERFERENCE IN WHICH CASE THE USER WILL BE REQUIRED TO CORRECT THE INTERFERENCE AT HIS OWN EXPENSE.

CAUTION: CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE PARTY

RESPONSIBLE FOR COMPLIANCE COULD VOID THE USER'S AUTHORITY TO OPERATE THE EQUIPMENT.

THIS CLASS A DIGITAL APPARATUS COMPLIES WITH CANADIAN ICES-003.

CET APPAREIL NUMÉRIQUE DE LA CLASSE A EST CONFORME À LA NORME NMB-003 DU CANADA.

CE COMPLIANCE STATEMENT

WARNING

This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.

CAUTION

RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE.

DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS

IMPORTANT SAFETY INSTRUCTIONS

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not us e this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ve ntilation openings. Ins tall in acc ordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves,

or other apparatus (including amplifiers) that produc e heat.

9. Do not def eat the safety purpose of the polarized or grounding-type plug. A polar ized plug has two blades wit h one wider than t he other. A grounding type plug has two blades and a thir d grounding pr ong. The wide blade or the

third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician fo r replacement of the obsolet e outlet.

10. Protect the power c ord from being walked on or pinc hed particularly at plugs convenience receptacles, and the poi nt where they exit from the apparatus.

11. Only use attachments/accessori es specified by the manufacturer.

12. Use only with the c art, stand, tripod, bracket, or table

specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

13. Unplug this apparat us during lightning storms or when

unused for long periods of time.

14. Refer all servicing t o qualified service personnel. Servicing is

required when the apparat us has been damaged in any way , such as power-

supply cord or plug is damaged, liqui d has been m oisture, does not operate normally, or has been dropped.

15. CAUTION – THESE SERVICING INSTRUCTIONS ARE FOR USE BY

QUALIFIED SERVICE PERSONNEL ONLY. TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT PERFORM ANY SERVICING OTHER THAN THAT CONTAINED IN THE OPERATING INSTRUCTIONS UNLESS YOU QRE QUALIFIED TO DO SO.

16. Use satisfy clause 2.5 of IEC60950-1/UL60950-1 or Certified/Listed Class

2 power source only.

17. ITE is to be connected only to P oE networks without ro uting to the outside plant.

TABLE OF CONTENTS

MODELS .......................................................................................................................................................... 11

KEY FEATURES ................................................................................................................................................ 11

COMPONENTS.................................................................................................................................................. 12

INSTALLATION ............................................................................................................................................ 13

BEFORE INSTALLATION.................................................................................................................................... 13

STARTING INSTALLATION ................................................................................................................................13

Base Installation ...................................................................................................................................... 13

Basic Configuration of Fastrax X18 Network Dome Camera System .............................................. 16

Setting Network Dome Camera Termination ...................................................................................... 17

Reset ......................................................................................................................................................... 17

Setting Network Dome Camera Address (ID) ..................................................................................... 19

Setting Network Dome Camera Protocol ............................................................................................. 19

Connections.............................................................................................................................................. 19

Setting Network Dome Camera Protocol ............................................................................................. 20

Micro SD Card Installation (Optional) .................................................................................................. 20

OPERATION................................................................................................................................................... 21

MINIMUM CONDITIONS FOR USING WEB BROWSER........................................................................................... 21

ACCESSING THE IP CAMERA............................................................................................................................. 21

MAIN MENU .................................................................................................................................................... 22

LIVE VIEW ..................................................................................................................................................... 23

LIVE VIDEO PAGE ICONS ................................................................................................................................. 23

PLAYBACK...................................................................................................................................................... 25

PLAYBACK VIEW .............................................................................................................................................. 25

SETUP.............................................................................................................................................................. 28

BASIC CONFIGURATION ................................................................................................................................... 28

Users ......................................................................................................................................................... 29

Network .................................................................................................................................................... 32

Image........................................................................................................................................................ 34

Audio ......................................................................................................................................................... 36

Date & Time............................................................................................................................................. 38

LIVE VIEW....................................................................................................................................................... 40

Source ....................................................................................................................................................... 40

VIDEO & IMAGE ..............................................................................................................................................42

Image – Basic .......................................................................................................................................... 43

Image – Auto Exposure.......................................................................................................................... 45

Image – Auto Focus................................................................................................................................48

Image – White Balance.......................................................................................................................... 50

Stream1 .................................................................................................................................................... 51

Stream2 .................................................................................................................................................... 54

Stream3 .................................................................................................................................................... 57

Stream4 .................................................................................................................................................... 60

Webcasting............................................................................................................................................... 64

AUDIO............................................................................................................................................................. 65

Basic .......................................................................................................................................................... 65

EVENT............................................................................................................................................................. 67

Event In – Alarm In ................................................................................................................................67

Event In – Manual Trigger ..................................................................................................................... 69

Event In – VMD Stream1 ....................................................................................................................... 70

Event In – VMD Stream3 ....................................................................................................................... 72

Event In – VMD Stream4 ....................................................................................................................... 74

Event Out – SMTP (Email) ..................................................................................................................... 76

Event Out – FTP & JPEG ........................................................................................................................ 78

Event Out – HTTP Server....................................................................................................................... 80

Event Out – Audio Alert.......................................................................................................................... 81

Event Out – Record................................................................................................................................. 84

Event Map ................................................................................................................................................ 85

Event Map - Add...................................................................................................................................... 87

DOME CONFIGURATION ................................................................................................................................... 89

Auto Scan ................................................................................................................................................. 89

Preset ........................................................................................................................................................ 92

Tour........................................................................................................................................................... 95

Pattern ...................................................................................................................................................... 98

Home......................................................................................................................................................... 99

Motor Setup ...........................................................................................................................................100

View Angle.............................................................................................................................................. 101

System Menu ......................................................................................................................................... 103

RS485...................................................................................................................................................... 104

SYSTEM......................................................................................................................................................... 105

Security - Users ..................................................................................................................................... 105

Security - HTTPS ................................................................................................................................... 108

Security – IP Filtering ........................................................................................................................... 110

Date & Time........................................................................................................................................... 111

NETWORK ..................................................................................................................................................... 113

Network - Basic ..................................................................................................................................... 113

Network – DDNS ................................................................................................................................... 115

Network – RTP....................................................................................................................................... 116

Network – UPnP .................................................................................................................................... 118

Network – QoS ...................................................................................................................................... 119

Language................................................................................................................................................ 120

Maintenance........................................................................................................................................... 121

Support ................................................................................................................................................... 123

ABOUT .......................................................................................................................................................... 124

TECHNICAL SPECIFICATIONS.............................................................................................................. 125

IMAGE ........................................................................................................................................................... 125

ELECTRICAL / CONNECTOR ............................................................................................................................ 125

VIDEO ........................................................................................................................................................... 125

PTZ .............................................................................................................................................................. 126

AUDIO........................................................................................................................................................... 126

SYSTEM INTEGRATION................................................................................................................................... 127

ENVIRONMENTAL........................................................................................................................................... 127

PHYSICAL ...................................................................................................................................................... 127

TROUBLESHOOTING ................................................................................................................................ 128

UPGRADING THE FIRMWARE .......................................................................................................................... 128

GENERAL TROUBLESHOOTING........................................................................................................................ 128

LIST of ILLUSTRATIONS

Figure 1. Typical System Configuration ......................................................................................13

Figure 2. Assemble bubble ring ass’y(Optional)........................................................................... 14

Figure 3. Installation.................................................................................................................14

Figure 4. Dimension..................................................................................................................15

Figure 5. Basic installation diagram............................................................................................16

Figure 6. Layout of Switches .....................................................................................................17

Figure 7. Setting Network Dome Camera Termination .................................................................17

Figure 8. Termination Diagram ..................................................................................................18

Figure 9. Main Menu .................................................................................................................22

Figure 10. Main Live View Page .................................................................................................23

Figure 11. Playback View ..........................................................................................................25

Figure 12. Basic Configuration ...................................................................................................28

Figure 13. Basic Configuration / Users........................................................................................ 29

Figure 14. Basic Configuration / User / Add User ........................................................................30

Figure 15. Basic Configuration / User / Modify User ....................................................................31

Figure 16. Basic Configuration / Network ...................................................................................32

Figure 17. Basic Configuration / Image ......................................................................................34

Figure 18. Basic Configuration / Audio .......................................................................................36

Figure 19. Basic Configuration / Date & Time .............................................................................38

Figure 20. Live View / Source ....................................................................................................40

Figure 21. Video & Image / Image - Basic ..................................................................................43

Figure 22. Video & Image / Image – Auto Exposure ...................................................................45

Figure 23. Video & Image / Image – Auto Focus ........................................................................ 48

Figure 24. Video & Image / Image – White Balance ....................................................................50

Figure 25. Video & Image / Stream1..........................................................................................51

Figure 26. Video & Image / Stream2..........................................................................................54

Figure 27. Video & Image / Stream2 ROI Setting........................................................................56

Figure 28. Video & Image / Stream3..........................................................................................57

Figure 29. Video & Image / Stream3 ROI setting ........................................................................ 59

Figure 30. Video & Image / Stream4..........................................................................................60

Figure 31. Video & Image / Stream4 ROI Setting........................................................................63

Figure 32. Video & Image / Webcasting ..................................................................................... 64

Figure 33. Audio / Basic ............................................................................................................ 65

Figure 34. Event / Event In – Alarm In.......................................................................................67

Figure 35. Event / Event In – Manual Trigger .............................................................................69

Figure 36. Event / Event In – VMD Stream1 ...............................................................................70

Figure 37. Event / Event In – VMD Stream3 ...............................................................................72

Figure 38. Event / Event In – VMD Stream4 ...............................................................................74

Figure 39. Event / Event Out – SMTP (Email) .............................................................................76

Figure 40. Event / Event Out – FTP & JPEG. ...............................................................................78

Figure 41. Event / Event Out – HTTP Server...............................................................................80

Figure 42. Event / Event Out – Audio Alert. ................................................................................81

Figure 43. Event / Event Out – Audio Alert / ARecoder window ...................................................82

Figure 44. Event / Event Out – Audio Alert / Encode Setup .........................................................83

Figure 45. Event / Event Out – Record .......................................................................................84

Figure 46. Event / Event Map ....................................................................................................85

Figure 47. Event / Event Map – Add...........................................................................................87

Figure 48. Dome Configuration / Auto Scan................................................................................89

Figure 49. Dome Configuration / Auto Scan / PTZ Control Panel .................................................. 90

Figure 50. Dome Configuration / Preset .....................................................................................92

Figure 51. Dome Configuration / Tour........................................................................................ 95

Figure 52. Dome Configuration / stored PTZ function list............................................................. 96

Figure 53. Dome Configuration / Pattern....................................................................................98

Figure 54. Dome Configuration / Home...................................................................................... 99

Figure 55. Dome Configuration / Motor Setup........................................................................... 100

Figure 56. Dome Configuration / View Angle ............................................................................ 101

Figure 57. Dome Configuration / System Menu......................................................................... 103

Figure 58. Dome Configuration / RS485 ................................................................................... 104

Figure 59. System / Security – Users .......................................................................................105

Figure 60. System / Security / Users – Add User ....................................................................... 106

Figure 61. System / Security / Users – Modify User................................................................... 107

Figure 62. System / Security – HTTPS...................................................................................... 108

Figure 63. System / Security – IP Filtering................................................................................ 110

Figure 64. System / Date & Time............................................................................................. 111

Figure 65. System / Network – Basic........................................................................................ 113

Figure 66. System / Network – DDNS ...................................................................................... 115

Figure 67. System / Network – RTP .........................................................................................116

Figure 68. System / Network – UPnP .......................................................................................118

Figure 69. System / Network – QoS ......................................................................................... 119

Figure 70. System / Language .................................................................................................120

Figure 71. System / Maintenance............................................................................................. 121

Figure 72. System / Support.................................................................................................... 123

Figure 73. About..................................................................................................................... 124

DESCRIPTION

--------------------------------

-----------------------------------------------------------------------------------------------------

This camera is an internet protocol based me

gapixel network camera with a built-in web

based viewer on Int

ernet Explorer

. The camera has a connection feature for third-party applications and compatible with supplied Utility software for easy installation and Client software to search, configure, manage, live view, record and playback.

The camera supports dual compression formats and multiple streaming simultaneously. The two standard compression formats include H.264 and MJPEG. The multiple streams can be configured to a variety of resolutions, bit rates and frame rates. The camera uses 1/3 inch CCD sensor and Focal length 4.7~84.6mm lens and also supports PoE (Power over Ethernet), DC12V, and AC24V.

Models

KNS-1108FT/V3 1.3 Megapixel, NTSC(PAL)

Key Features

 HDTV Video Quality

The KNS-1108FT/V3 is ca

pable of providing the outstanding image quality with HDTV performance and

profiles (High, Main

, and Baseline) in H.264 compression.

 Multiple Streaming

Each stream can be programmed independently and transmitted using different configurations.

 ROI (Region of Interest)

The ROI features that transmit specially selected area in the primary stream using different FPS,

Resolution, Bit Rates and Picture Quality.

 Dual Codec (H.264, MJPEG)

The KNS-1108FT/V3 supports two standard compr

essions formats H.264 and MJPEG.

 Built-i

n optical Zoom

Support maximum 18x opti

cal and 12x digital zoom. (Total 216x Zoom).

 Intelligent Video Motion Detection

The KNS-1108FT/V3 offers intelligent & sophisticated video motion detection for each multiple streams

 Triple Power (Power

over Ethernet, DC12V, AC24V)

This camera supports Power over Ethernet (PoE), which supplies power to the camera through the

network. If the network has no PoE, connect a DC12V or AC24V power connector.

 Day and Night

The KNS-1108FT/V3 provides clear monitoring images even in low light conditions using IR-cut filter.

 SD Local Recording

The KNS-1108FT/V3 provides local video recording function. When camera detects video motion or alarm events or manual trigger, it can record video stream by itself.

 Voice Alert Linked to Alarm Detection

The KNS-1108FT/V3 can play the audio file stored in the camer

a in synchronization with alarm detection

by the s

ensor input or the motion detection function.

 Network Flow Control

The KNS-1108FT/V3 provides a flow control function which enhances network efficiency by significantly restricting user video streams with designating the maximum bandwidth.

 ONVIF Certificate

The KNS-1108FT/V3 network camera complies with the ONVIF certificate. ONVIF (Open Network Video Interface Forum) is an open industry forum for the development of a global standard for the interface of network video product.

Components

Quantity Description

1 Camera

1 Bubble Ring

3 Assembly Screws for Attaching Network Dome Camera

1 Installation CD

3 Plastic Anchor

NOTE

Adapter for DC12V / AC24V are not supplied.

INSTALLATION

-------------------------------------------------------------------------------------------------------------------------------------

Before Installation

Before installing the camera, thoroughly familiarize yourself with the information in this section of

the manual.

- Recommend connecting the camera to a network that uses a DHCP (Dynamic Host Configuration

Protocol) server to address devices.

- To ensure secure access to the IP camera, place the camera behind a firewall when it is connected to a network.

Starting Installation

Base Installation

Figure 1. Typical System Configuration

push

remove window

assemble bubble ring ass'y

push

remove camera window

bubble ring ass'y

screw

Figure 2. Assemble bubble ring ass’y(Optional)

NOTES

It is recommended to remove camera window for improving picture quality when you use bubble ring assy.

The Network Dome Camera is for use in surface mounting applications and the mounting surface should be capable of supporting loads up to 10lb (4.5kg).

The Network Dome Camera’s base should be attached to a structural object, such as hard wood, wall stud or ceiling rafter that supports the weight of the Network Dome Camera.

Figure 3. Installation

Figure 4. Dimension

Basic Configuration of Fastrax X18 Network Dome Camera System

Figure 5. Basic installation diagram

The Network Dome Camera must be installed by qualified service personnel in accordance with all local and federal electrical and building codes. The system should be installed according to Figures 5 through 8.

Figure 6. Layout of Switches

Setting Network Dome Camera Termination

The device which is connected at end of line, whether it be a Network Dome Camera or keyboard controller, must have the cable for communication terminated by setting the appropriate DIP switch. Without proper termination, there is potential for control signal errors. Total length of the cable for communication should not exceed 1.2km (4000ft).

SW1 1 2

Terminated ON RESET

Not terminated OFF OFF

Figure 7. Setting Network Dome Camera Termination

Reset

Restore the camera’s factory default settings. The dip switch 2 is on for 15s and then off. Please take steps as follows:

1. Power off

2. Press the switch 2 to On

3. Supply the camera with power

wait for 15 seconds and relocated SW2 off

Figure 8. Termination Diagram

Setting Network Dome Camera Address (ID)

To prevent damage, each Network Dome Camera must have a unique address (ID). When installing multiple Network Dome Cameras using a multiplexer, it is suggested that the Network Dome Camera address match the multiplexer port number. If you want to set the address more than 999, you should contact the service provider.

Refer to ‘Dome Configuration - RS485’ section for detailed information.

Setting Network Dome Camera Protocol

If a Network Dome Camera is to be installed with a Fastrax keyboard controller, select the default protocol. Consult service personnel if a Network Dome Camera is installed with device other than a keyboard controller.

Refer to ‘Dome Configuration - RS485’ section for detailed information.

Connections

 Connecting to the RS485

The Network Dome Camera can be controlled remotely by an external device or control system, such as a control keyboard, using RS485 half-duplex serial communications signals. Connect Marked Rx+, Rx- to Tx+ and Tx- of the RS485 control system.

 Connecting Video out connector

Connect the video out (BNC) connector to the monitor or video input.

 Connecting Alarms

AL1 to 2 (Alarm In)

You can use external devices to signal the Network Dome Camera to react on events. Mechanical or electrical switches can be wired to the AL (Alarm In) and GND (Ground) connectors.

GND(Ground)

Connect the ground side of the Alarm input and/or alarm output to the GND connector.

NC (NO) (Normal Close or Normal Open: Alarm Out)

The Network Dome Camera can activate external devices such as buzzers or lights. Connect the device to the NC (NO) (Alarm Out) and COM (Common) connectors.

 Connectin

g the Network

The Network Dome Camera supports the operation through the network. Therefore, it is necessary to connect a standard RJ-45 cable to it. Generally a cross cable is used for directly connection to PC, while a direct cable is used for connection to a hub.

 Connecting the Power

Connect the power of DC 12V to the Network Dome Camera. Use certified / Listed Class 2 power supply transformer only.

Setting Network Dome Camera Protocol

When a camera, Encoder or Decoder is first connected to the network it has no IP address. So, it is necessary to allocate an IP address to the device with the “Smart Manager” utility on the CD.

Micro SD Card Installation (Optional)

Insert Micro SD card for local recording.

OPERATION

-------------------------------------------------------------------------------------------------------------------------------------

Before starting the camera, installation must be complete. The camera completes a configuration sequence within approximately 40 seconds when power is supplied. The amber LED of this megapixel camera flash one time per second indicating the configuration sequence is complete.

NOTES

- If the DHCP is enabled but the camera is not connected to a DHCP server, the camera will be set

default IP 192.168.30.220 and try to get IP from DHCP server about every two seconds.

- Network and processor bandwidth limitations might cause the video stream to pause or appear

pixilated when an increased number of Web-interface users connection to the camera. Decrease the images per second, resolution, compression, or bit rate settings of the Web-interface video streams to compensate for network or processor limitations.

Minimum conditions for using web browser

The minimum system requirements to use a Web browser with this IP camera are as follows:

- CPU: Pentium

4 microprocessor, 2.0GHz

- Operational System: Windows XP

or Windows Vista® or Windows 7®

- System Memory: RAM 512 Mbyte

- Ethernet: 100 Mbit

- Video Resolution: 1024(Horizontal) x 768(Vertical) pixels or higher

- Internet Explorer

7 or later

- ActiveX

1.0.0.13 or later

Accessing the IP camera

1. Open Web browser

- Double click Internet Explorer

icon.

2. Type IP address

- Type the camera’s IP address in the Internet Explorer

address bar.

- The default IP address is

192.168.30.220

NOTES

- If you do not know the camera’s IP address, install the SmartManager® utility software available

on the CD supplied with the product. The utility software will locate the assigned Model name, Host name, MAC address, IP address, Version and others.

- Refer to the SmartManager

utility software manual for more detail.

3. Lo

g On to the camera

- Click the Live View icon for default live image view or the Setup icon to change the configuration values.

Main Menu

Figure 9. Main Menu

The dialog box will be appears.

- Type User ID and Password in the dialog box. The default User ID and Password is

admin

NOTE

For security purposes, be sure to change the password after you log on for the first time.

LIVE VIEW

-------------------------------------------------------------------------------------------------------------------------------------

The Live View page provides you to select the properties of video source. You can view the live image from this page and also access the Setup menu and operate the main functions.

Figure 10. Main Live View Page

Live Video Page Icons

Hide Main Icons: Hides main icons in the live view page. Show Main Icons: Shows main icons in the live view page.

Live view: Displays live video stream.

Playback View: Enters playback menu.

Setup: Enters setup menu.

Help: Shows helpful information.

Source: Specify the viewable video stream source to display in live view page.

View Size: Specify the viewable video size to display in live view page.

Stream Type: Specify the internet protocol to display in live view page.

ROI View: Specify the specially selected area to transfer using different stream feature in the

primary video image. ROI is an abbreviation for “Region of Interest”.

Pause: Pause the live video stream.

Snapshot: Take a picture of the video image currently on display. Supports the origin image

size view, Print, and Save feature.

Digital Zoom: Supports a digital zoom in live video image.

Full Screen: Expands video image to the entire screen area.

Manual Trigger: Activates the Alarm Out signaling manually.

PTZ Control: Activates PTZ Control Panel

Speaker: Adjusts the volume of Speaker and switch the sound on / off.

Microphone: Adjusts the volume of Microphone and switch the sound on /

off.

PLAYBACK

-------------------------------------------------------------------------------------------------------------------------

This Playback page provides current SD recorded file lists and information. It also supports easy

access and how to playback the recorded stream.

Playback View

User can access the recorded image in the web browser.

Figure 11. Playback View

Event List: Shows the recorded lists by Alarm, Trigger and Motion event.

Event Search: Select the start date and end date you want to playback, and then click the Go

button to show the list. In case of you want to list up according to event type, click the arrow button and select event type.

Calendar: Shows the information about playback image. Playback Control Buttons: Provides user favorite functions.

Go to the first.

Fast backward play

Backward play

Backward step

Pause

Forward step

Forward play

Fast forward play

Go to the last

Clip copy

Digital Zoom

Full Image

Clip Copy: Provides avi format file.

Please step as follows;

1. Sel

ect Start Date/Time and End Date/Time.

2. Set Export Path.

3. Click Estimate button which is shown the file FPS and Size.

4. Click Export or Cancel button.

NOTES

1. If you set successfully, the following pop-up windows will be appeared.

2. In case of mismatching of the Start or End Date/Time, the following windows will be appeared. Please retry to set the Start or End Date/Time.

3. In case of no image data between the Start Date/Time and End Date/Time, the following windows will be appeared. Please retry to set the Start or End Date/Time.

4. The buttons from

to indicate an Hours and the number from 0 to 60 indicate a minutes.

SETUP

-------------------------------------------------------------------------------------------------------------------------------------

The SETUP pages provide you to manage the camera and change the setting values. For the easy and quick access the video, the setup menu is configured two parts, which are Basic Configuration and advanced configuration. The Basic Configuration menu allows you to setup Users, basic Network and Image. The remaining configuration parts help to setup user dependent values and provide more advanced settings.

Basic Configuration

Basic Configuration supply user to access the camera image using minimum setting. Also it shows the camera basic information such as Model name, Firmware version and MAC address.

Figure 12. Basic Configuration

NOTE

The setting menu might not be available if the user does not have the permission to access this

feature. The only required setting is the IP address, which is set on the Network page. All other settings are available with default values and optional.

Users

Use the Users tab to manage user permission to access the camera.

Figure 13. Basic Configuration / Users

User Setting: Click the Enable anonymous viewer login checkbox to enable anonymous user

User List Setting: User accounts can be added or modified or removed. The authority

depends upon user group automatically and shows the permission status to access the menus. The default user name / password is

admin

User Name: Shows the name which registered to access the camera. User Group: Shows the assigned permission given to users. Authority: Shows the permission status to access the menus.

- Click the A

dd, Modify, or Remove button for managing user account.

Figure 14. Basic Configuration / User / Add User

To add a new user:

1. Click the Add tab, and then new pop-up window appears.

2. Click in the User name box and type a new user name (1 to 14 alphanumeric characters). User names are not case sensitive.

3. Click in the Password box and type a password (1 to 8 alphanumeric characters). Passwords are case sensitive.

4. Click in the Confirm password box and retype a password.

5. Click in the User group box and select one of the groups you wish to assign to the user.

6. Click the OK button to save the settings and add a new user.

Figure 15. Basic Configuration / User / Modify User

To modify a user:

1. Select one of the User Name in the User List Setting you want to modify.

2. Click the Modify tab, and then new pop-up window appears.

3. Click in the Password box and type a password (1 to 8 alphanumeric characters). Passwords are case sensitive.

4. Click in the Confirm password box and retype a password.

5. Click in the User group box and select one of the groups you wish to assign to the user.

6. Click the OK button to save the settings and modify a user.

NOTE

The user name can’t be modified.

To remove a user:

1. Select one of the User Name in the User List Setting you want to remove.

2. Click the Remove tab. A dialog box appears with confirmation message.

3. Click the OK button. The user profile is removed from the User List Setting profile.

NOTE

The admin user name can’t be modified.

- Click the Save button to save the settings, or click the Reset button to clear all of the information

you entered without saving it.

Network

Use the Network tab to manage basic network settings.

Figure 16. Basic Configuration / Network

IP Address Configuration: The DHCP (Dynamic Host Configuration Protocol) server has a

feature that automatically assigns an IP address to the device if there is a device on the network.

Obtain IP address via DHCP: Select the choice box if you want to assign the IP address from

DHCP server automatically, and then the remaining setting are read-only text.

Use the following IP address: Select the choice box if you want to assign the IP address

manually.

IP address: The address of the camera connected to the network. Specify a unique IP address

for this network camera.

Subnet mask: The address that determines the IP network that the camera is connected to

(relative to its address). Specify the mask for the subnet the network camera is located on.

Default router: The router that accesses other networks. Specify the IP address of the default

router (Gateway) used for connecting devices attached to different networks and network segments.

IPv6 Address Configuration: Check the Enable IPv6 check-box to enable IPv6 address

configuration. Other settings for IPv6 are configured in the network router.

DNS Configuration: DNS (Domain Name Service) provides the translation of host names to IP

addresses on your network.

Obtain DNS server via DHCP: Select the choice box if you want to use the DNS server

settings provided by the DHCP server automatically, and then the remaining setting are read-only text.

Use the following DNS server address: Select the choice box if you want to use the desired

DNS server manually.

Domain name: Enter the domain to search for the host name used by the network camera. Primary DNS server: Enter the IP address of the primary DNS server. Secondary DNS server: Enter the IP address of the secondary DNS server.

- Click the Save button to save the settings, or click the Reset button to clear all of the information

you entered without saving it.

Image

Use the Image tab to adjust the camera image setting value and orientation.

Figure 17. Basic Configuration / Image

Image Appearance: The image appearance allows you to adjust the camera setting

parameters and change the camera orientation. All of parameters are recommended to be modifying for good image quality suitable for installation place.

Sharpness: Control the clarity of detail in a scene. The sharpness can be adjusted in the range 1-

32 and Auto. The default setting is auto.

Enable flip image: Rotate the camera image 180 degrees vertically. Preset freeze: The image is frozen during calling preset.

FNR Control: FNR (Field Noise Reduction) is a function to decrease the noise by the field

correlation.

FNR: Control FNR effect. The FNR can be adjusted in the range off-high. The default setting is off. Level: Adjusts the FNR level in manual mode. The level can be adjusted in the range 1-16. The

default setting is 1.

Digital Zoom Control: The digital zoom control allows you to adjust the limit of digital zoom

ratio.

Digital zoom: The digital zoom can be adjusted in the range off-Max. The default setting is off.

(1280×960 resolution only).

Off Zoom range is limited to the optical.

x2 Zoom is extendable 2x of digital zoom range.

x4 Zoom is extendable 4x of digital zoom range.

Max Zoom is extendable Max digital zoom range.

- Click the Save button to save the settings, or click the Reset button to clear all of the information

you entered without saving it.

Audio

Use the Audio tab to manage the basic audio settings for the camera.

Figure 18. Basic Configuration / Audio

Audio Setting: Click the Enable audio checkbox to enable audio. This page describes how to

configure the basic audio settings for the camera. This camera supports the audio full duplex that can be transmits and receives audio in both directions at a time.

Compression type: G.711 is the international standard for encoding wired-telephone audio on

64kBit/s channel. It is a PCM (Pulse Code Modulation) scheme operating at 8 kHz sample rate. The default setting is G.711 µ-law.

Sample rate: Indicates the number of times per second the sound is sampled. The default

setting is 8 kHz.

NOTE

G.711, also known as Pulse Code Modulation (PCM), is a very commonly used waveform codec. G.711 uses a sampling rate of 8,000 samples per second, with the tolerance on that rate 50 parts per million (ppm). Non-uniform quantization (logarithmic) with 8 bits is used to represent each sample, resulting in a 64 kbit/s bit rate. There are two slightly different versions; μ-law, which is used primarily in North America, and A-law, which is in use in most other countries outside North

America. G.711 μ-law tends to give

more resolution to higher range signals while G.711 A-law

provides more quantization levels at lower signal levels.

Audio Input: Adjusts the audio volume especially from the Mike.

Input volume: The Input volume can be adjusted in the range from -21.00 to 21.00 dB. The

default setting is 0 dB. Click the Mute box if you do not want the audio input.

Audio Output: Adjusts the audio volume especially to the Speaker.

Output volume: The Output volume can be adjusted in the range from -18.1 to 6.0 dB. The

default setting is 0 dB. Click the Mute box if you do not want the audio output.

- Click the Save button to save the settings, or click the Reset button to clear all of the information

you entered without saving it.

Date & Time

Use the Date and Time tab to set the camera’s date and time by manually or automatically.

Figure 19. Basic Configuration / Date & Time

Current Server Time: Shows the current date and time.

Date: The default setting is 1970-01-01. Time: The default setting is 00:00:00.

New Server Time: Select the time zone where your camera is located.

Click the "Automatically adjust for daylight saving changes" checkbox to automatically update the time changes caused by daylight saving.

Time zone: The default setting is GMT. Time mode: The default setting is Set manually. Synchronize with computer time: Sets the time according to the clock on your computer.

Synchronize with NTP Server: This option will obtain the correct time from an NTP server

every 60 minutes. The NTP server's IP address or host name is specified in the time server.

Set manually: Using this option allows you to manually enter the date and time.

Date & Time Format: Select one of the Date and Time format.

Date Format: The default setting is YYYY-MM-DD. Time Format: The default setting is 24 hours.

- Click the Save button to save the settings, or click the Reset button to clear all of the information

you entered without saving it.

Live View

Use the Source tab to configure the live view video source and composite video output properties.

Source

Configure the default live view source in the web browser and composite video output source.

Figure 20. Live View / Source

View Size: Select which formats do you want as default live view source.

Enable cookie: Click the Enable cookie box if you want to reload the last configuration settings. Use the followings: Click the Use the following box to configure the video properties to be

displayed in the live view page.

Source: Select one of the stream sources to be displayed in the live view page. The default setting

is Stream1.

View size: Select one of the view sizes to be displayed in the live view page. The default setting

is a 1280x720.

Stream type: Select one of the stream protocols. The default setting is UDP.

Default TV out: Configure the composite video output properties.

Mode: Select the composite video output format. The default setting is NTSC. Source: Select one of the composite video output sources. The default setting is stream1.

Sequence If you select Sequence, the composite video output repeats the video

images on a single video pane according to <Sequence Mode Setting>.

Click the checkbox if you want to assign each stream into Sequence Mode. Each stream dwell time shows the dwelling time / intervals of each stream when the stream set the sequence mode.

Stream1 Dwell Time

Enter stream1 dwell time. The dwell time can be adjusted in the range 3-3600 seconds. The default setting is 5 seconds.

Stream2 Dwell Time

Enter stream2 dwell time. The dwell time can be adjusted in the range 3-3600 seconds. The default setting is 5 seconds.

Stream3 Dwell Time

Enter stream3 dwell time. The dwell time can be adjusted in the range 3-3600 seconds. The default setting is 5 seconds.

Stream4 Dwell Time

Enter stream4 dwell time. The dwell time can be adjusted in the range 3-3600 seconds. The default setting is 5 seconds.

- Click the Save button to save the settings, or click the Reset button to clear all of the information

you entered without saving it.

Video & Image

Use the Video & Image tab to select a preset camera stream configuration or configure custom video stream settings. The camera features multiple video streams with selectable settings for Profile, Resolution, Bit rate control, Compression, and Frame rate. The default names for the streams are Stream1, Stream2, Stream3, and Stream4. Although each stream can be programmed independently, the settings of one stream can limit the options available for the other stream depending on the processing power used.

NOTES

- H.264 is the new generation compression standard for digital video, also known as MPEG4 Part 10.

This function offers higher video resolution than Motion JPEG or MPEG4 at the same bit rate and bandwidth, or the same quality video at a lower bit rate.

- MJPEG (Motion Joint Photographic Experts Group) is a simple compression technique for networked video. Latency is low and image quality is guaranteed, regardless of movement or complexity of the image. Image quality is controlled by adjusting the compression level, which in turn provides control over the file size, and thereby the bit rate.

Image – Basic

Use the Image-Basic tab to adjust the camera image setting values and orientation.

Figure 21. Video & Image / Image - Basic

Image Appearance: The image appearance allows you to adjust the camera setting

parameters and change the camera orientation. All of parameters are recommended to be modifying for good image quality suitable for installation place.

Sharpness: Control the clarity of detail in a scene. The sharpness can be adjusted in the range 1-

32 and Auto. The default setting is auto.

Enable flip image: Rotate the camera image 180 degrees vertically. Preset freeze: The image is frozen during calling preset.

FNR Control: FNR (Field Noise Reduction) is a function to decrease the noise by the field

correlation.

FNR: Control FNR effect. The FNR can be adjusted in the range off-high. The default setting is off. Level: Adjusts the FNR level in manual mode. The level can be adjusted in the range 1-16. The

default setting is 1.

Digital Zoom Control: The digital zoom control allows you to adjust the limit of digital zoom

ratio.

Digital zoom: The digital zoom can be adjusted in the range off-Max. The default setting is off.

(1280×960 resolution only).

Off Zoom range is limited to the optical.

x2 Zoom is extendable 2x of digital zoom range.

x4 Zoom is extendable 4x of digital zoom range.

Max Zoom is extendable Max digital zoom range.

- Click the Save button to save the settings, or click the Reset button to clear all of the information

you entered without saving it.

Image – Auto Exposure

Use the Auto Exposure tab to control the Auto Exposure.

Figure 22. Video & Image / Image – Auto Exposure

Exposure Control: Exposure is the amount of light detected by the camera sensor. A scene

with correct exposure settings has adequate detail and contrast between white and dark values. An

image with t

oo little or too much exposure determines detail in the scene. The camera features

auto and manual exposure settings.

Exposure mode: Supports exposure modes to control the amount of light detected by the

camera sensor base on settings for light conditions. The default setting is Auto with DARK.

Auto Automatic Exposure.

Auto with DAWN Under the low light condition when night shot mode is Auto,

IR Cut filter is automatically turned on and off.

Auto with DARK IR Cut filter is automatically turned on and off more dark

condition than Auto with DAWN.

Auto with DSS Digital Slow Shutter (DSS) is automatically changed with sets

the amount of light.

Manual Gain

Adjust the gain manually.

Manual Shutter

Adjust the electronic shutter manually.

Manual Exposure

Adjust the exposure manually.

DSS limit: Set a limit on auto digital slow shutter if the camera automatically slows the shutter

speed when it detects low light. The default setting is 1/15 sec.

Iris offset: Set the overall brightness of a picture. (000-255, default: 144) Increase the value to

brighten the scene. Decrease the level to darken the scene. This is helpful when the scene is too bright or too dark.

Iris peak: Set the effect of focusing peak, or how video peaks affect the overall picture brightness.

The iris peak can be adjusted in the range 0-127. The default setting is 8. When the scene have bright lights such as spotlight or headlight, if you set Iris peak level high, the image get dark because of the effect of focusing peaks. Overall picture darkens.

If you set Iris peak level low, the image has no effect of focusing peak and the image of spot

lights get white. Overall picture remains but spot light become very bright.

When you set Iris offset level low in an image with spotlights, a soft image may occurs because of

the image of on and around the spotlights get saturated.

AGC gain: Increasing Exposure gain increases the brightness of image, but it also increases the

amount of noise in the image. The exposure gain can be adjusted in the range 0-30. The default setting is 6.

Shutter speed: Select the electronic shutter speed. It’s only available when Exposure mode is a

Manual shutter mode. The Shutter speed can be adjusted in the range 1/10000-1/4sec. The default setting is 1/30sec.

Exposure: Select the Iris. It’s only available when Exposure mode is a Manual Exposure mode.

The Iris can be adjusted in the range F1.6-F34. The default setting is F3.2.

Day & Night Control: Day & Night controls the position of the IR (Infra Red) cut filter,

which determines the color or block-white setting of the camera. The Day & Night settings change depending on the exposure settings. If the camera Exposure mode is set to Auto with DAWN or DARK, the Day & Night mode can be set to Auto only.

Day & Night mode: Supports Day & Night mode to transit the IR cut filter. The default setting is

auto.

Auto Automatically controls the IR cut filter depending on the light conditions.

Day Deliver color image regardless of light.

Night Deliver B/W image regardless of light.

Global Control the Day & Night mode by the keyboard.

WDR & BLC Control: The backlight compensation is an ability of a camera to balance the

lighting in a scene with an extremely bright background such as sunlight. It helps to obtain the finest light contrast and get clear image. On the other hand, the wide dynamic range (WDR) function provides clear images even under back light circumstances where intensity of illumination can vary excessively, namely when there are both very bright and very dark areas simultaneously in the field of view of the camera.

Mode: WDR cannot be set simultaneously with BLC. The default setting is off. Level: Control the level of BLC. The level can be adjusted in the range Very low-Very high. The

default setting is Very low.

- Click the Save button to save the settings, or click the Reset button to clear all of the information

you entered without saving it.

Image – Auto Focus

Use the Auto Focus tab to control the Auto Focus.

Figure 23. Video & Image / Image – Auto Focus

Focus Control: Auto focus intelligently adjusts the camera lens to obtain focus on the subject.

Focus mode: KNS-1108FT/V3 provides various focus mode.

Auto

Focus is automatically adjusted always.

Manual Focus is automatically adjusted during zoom or PTZ position is

changed. When 3 seconds have passed after zoom or PTZ position is changed, focus is changed in manual mode.

One Push Focus is automatically adjusted just once, after zoom or PTZ position

is changed. Focus is changed into manual focus.

Constant Manual

Focus can be manually adjusted with using FAR or NEAR button.

Focus limit: Set the minimum focus length under 18x zoom ratio. The Focus limit can be

adjusted in the range 1cm-1.5m. The default setting is 30cm.

NOTE

Avoid continuous, 24-hour use of the auto focus. This will shorten the lifespan of the lens.

- Click the Save button to save the settings, or click the Reset button to clear all of the information

you entered without saving it.

Image – White Balance

Use the White Balance tab to control the white balance.

Figure 24. Video & Image / Image – White Balance

White Balance Control: White Balance Control defines how the camera processes video

images to render true colors in a scene. White balance is especially effective in scenes with changing lighting conditions or in scene with more than one type of light source.

White balance mode: Provides the options for White Balance. The default setting is Auto.

Auto Automatically delivers the best possible image by adjusting the white

balance based on the colors in the scene.

Indoor

Select when the camera is installed at indoor.

Outdoor

Select when the camera is installed at outdoor.

Manual gain

Enter to the manual gain setting mode.

NOTE

In some installations, use manual white balance to render the most accurate image color possible.

White balance position: Move the white balance position into current color temperature.

A higher value in the Indoor means the blue color increase and a higher value in the Outdoor means the red color increase. The White balance position can be adjusted in the range 0-127. The default setting is 64.

White balance R gain: Adjusts the picture output in the red range. The White balance R gain

can be adjusted in the range 0-255, where a higher value produces a higher red image. The default setting is 100.

White balance B gain: Adjusts the picture output in the blue range. The White balance B gain

can be adjusted in the range 0-255, where a higher value produces a higher blue image. The default setting is 100.

- Click the Save button to save the settings, or click the Reset button to clear all of the information

you entered without saving it.

Stream1

The Stream1 features the H.264 compression standard for primary stream.

Figure 25. Video & Image / Stream1

H.264 Setting: Configures the H.264 setting value for stream1.

Profile: Selects the stream profile that is to be used for transmissions. The default setting is High.

High The primary profile for broadcast and disc storage applications,

particularly for HDTV (High-Definition television) or Blu-ray Disc applications.

Main Originally intended as the mainstream consumer profile for broadcast

and storage applications. Additional tools over baseline profile include: B slice type.

Baseline Primarily for low-cost applications that requires additional error

robustness such as video conferencing, video over-IP and mobile applications. Tools used by baseline profile include: I and P slice types.

Resolution: Specified as the number of pixel-columns (width) by the number of pixel-rows

(height). The Resolution can be adjusted in the range from 320x240 to 1280x960. The default setting is 1280x720.

NOTE

The maximum resolution setting might not be obtainable due to programmed compression standard and processor power.

Bit rate control: The bit rate can be set as VBR (Variable Bit Rate) or CBR (Constant Bit Rate).

VBR Automatically adjusts the bit rate according to the image complexity,

using up bandwidth for increased activity in the image, and less for lower activity in the monitored area.

CBR Allows you to set a fixed target bit rate that consumes a predictable

amount of bandwidth. As the bit rate would usually need to increase for increased image activity, but in this case can not, the frame rate and image quality are affected negatively.

Bit rate:

Indicates the quality of the video stream (rendered in kilobits per second). The higher value means the higher video quality and bandwidth required. The Compression can be adjusted in the range from 100 to 6000 kbps. The default setting is 4000 kbps.

Quality: Automatically adjusts the compression rate to guarantee the image quality at only VBR

mode. The default setting is Middle.

Frame rate: Indicates the number of fps (frame per second) available for the video stream

configuration. The Frame rate can be adjusted in the range from 1 to 30 fps. The default setting is 30 fps.

NOTES

- The maximum frame rate setting might not be obtainable due to programmed compression standard, resolution of the stream, and processor power.

- A higher

frame rate is advantageous when there is movement in the video stream, as it maintains

image quality throughput.

GOP structure: Describes the composition of the video stream. This GOP (Group of Picture)

setting configures the number of partial frames that occur between full frames in the video stream. For example, in a scene where a door opens and a person walks through, only the movements of the door and the person are stored by the video encoder. The stationary background that occurs in the previous partial frames is not encoded because no changes occurred in that part of the scene; the stationary background is only encoded in the full frames. Partial frames improve video compression rates by reducing the size of the video. As the GOP increases, the number of partial frames increases between full frames. This setting is only available with H.264 compression standards. The default setting is IP. Please consult with your network administrator before changing.

GOP size: The higher value saves considerably on bandwidth but may have an adverse effect on

image quality. Higher values are only recommended on networks with high reliability. The GOP size can be adjusted in the range from 1 to 60. The default setting is 30. Please consult with your network administrator before changing.

- Click the Save button to save the settings, or click the Reset button to clear all of the information

you entered without saving it.

Stream2

The Stream2 features the MJPEG compression standard for ROI.

Figure 26. Video & Image / Stream2

MJPEG Setting: Configures the MJPEG setting value for stream2.

Resolution: Specified as the number of pixel-columns (width) by the number of pixel-rows

(height). The Resolution can be adjusted in the range from 320x240 to 720x576. The default setting is 320x240.

NOTE

The maximum resolution setting might not be obtainable due to programmed compression standard and processor power.

Bit rate control: The bit rate can be set as VBR (Variable Bit Rate) or CBR (Constant Bit Rate).

VBR Automatically adjusts the bit rate according to the image complexity,

using up bandwidth for increased activity in the image, and less for lower activity in the monitored area.

CBR Allows y

ou to set a fixed target bit rate that consumes a predictable amount of bandwidth. As the bit rate would usually need to increase for increased image activity, but in this case can not, the frame rate and image quality are affected negatively.

Bit rate: Indicates the quality of the video stream (rendered in kilobits per second). The higher

value means the higher video quality and bandwidth required. The Compression can be adjusted in the range from 100 to 6000 kbps. The default setting is 2000 kbps.

Frame rate: Indicates the number of fps (frame per second) available for the video stream

configuration. The Frame rate can be adjusted in the range from 1 to 30 fps. The default setting is 30 fps.

NOTES

- The maximum frame rate setting might not be obtainable due to programmed compression standard, resolution of the stream, and processor power.

- A higher frame rate is advantageous when there is movement in the video stream, as it maintains image quality throughput.

Text Overlay Setting: Allows you to overlay user favorite text into image. Click the Enable

text overlay box to enable text overlay.

Content: Click in the Content box and type a description for the text you are creating (from 1 to

20 alphanumeric characters).

Location: Select the appropriate place to locate the Content description. Display timer: Provides the device timer setting value. The default setting is OFF.

ROI Setting: ROI (Region of Interest) features that transmit the specially selected area in the

primary stream using different channel, resolution, and frame rate.

Open ROI viewer: Click the Open ROI viewer box and then appears the new popup window to

assign the ROI stream.

Figure 27. Video & Image / Stream2 ROI Setting

Configure ROI as follows:

1. Click Enable ROI ZOOM check box, if you want to resize ROI area.

2. Move the square box to specific region or adjust the size of square box if you want.

3. User can configure ROI setting using arrow key to move the position of square box or using scroll bar to adjust the size of square box.

4. User can save the ROI as a preset and access to preset position in easy way. First, selects the preset position and then just click “Go” button.

NOTES

- The ROI setting values in this page are applied as soon as clicking / moving.

- ROI ZOOM function can slow down the performance of the camera

- Click the Save button to save the settings, or click the Reset button to clear all of the information you entered without saving it.

Stream3

The Stream3 features the H.264 compression standard for ROI.

Figure 28. Video & Image / Stream3

H.264 Setting: Configures the H.264 setting value for stream3.

Profile: Choose a profile. The default setting is High.

High The primary profile for broadcast and disc storage applications,

particularly for HDTV (High-Definition television) or Blue-ray Disc applications.

Main

Originally intended as the mainstream consumer profile for broadcast and storage applications. Additional tools over baseline profile include: B slice type.

Baseline

Primarily for low-cost applications that requires additional error robustness such as video conferencing, video over-IP and mobile applications. Tools used by baseline profile include: I and P slice types.

Resolution: Specified as the number of pixel-columns (width) by the number of pixel-rows

(height). The Resolution can be adjusted in the range from 320x240 to 720x576. The default setting is 320x240.

NOTE

The maximum resolution setting might not be obtainable due to programmed compression standard and processor power.

Bit rate control: The bit rate can be set as VBR (Variable Bit Rate) or CBR (Constant Bit Rate).

VBR Automatically adjusts the bit rate according to the image complexity,

using up bandwidth for increased activity in the image, and less for lower activity in the monitored area.

CBR Allows you to set a fixed target bit rate that consumes a predictable

amount of bandwidth. As the bit rate would usually need to increase for increased image activity, but in this case can not, the frame rate and image quality are affected negatively.

Bitrate: Indicates the quality of the video stream (rendered in kilobits per second). The higher

value means the higher video quality and bandwidth required. The Compression can be adjusted in the range from 100 to 2000 kbps. The default setting is 500 kbps.

Quality: Automatically adjusts the compression rate to guarantee the image quality at only VBR

mode. The default setting is Middle.

Frame rate: Indicates the number of fps (frame per second) available for the video stream

configuration. The Frame rate can be adjusted in the range from 1 to 30 fps. The default setting is 30 fps.

NOTES

- The maximum frame rate setting might not be obtainable due to programmed compression

standard, resolution of the stream, and processor power.

- A higher frame rate is advantageous when there is movement in the video stream, as it maintains

image quality throughput.

GOP structure: Describes the composition of the video stream. This GOP (Group of Picture)

GOP size: The higher value saves considerably on bandwidth but may have an adverse effect on

Text Overlay Setting: Allows you to overlay user favorite text into image. Click the Enable

text overlay box to enable text overlay.

Content: Click in the Content box and type a description for the text you are creating (from 1 to

20 alphanumeric characters).

Location: Select the appropriate place to locate the Content description. Display timer: Provides the device timer setting value. The default setting is OFF.

ROI Setting: ROI (Region of Interest) features that transmit specially selected area in the

primary stream using different channel, resolution, and frame rate.

Open ROI viewer: Click the Open ROI viewer box and then appears the new popup window to

assign the ROI stream.

Figure 29. Video & Image / Stream3 ROI setting

Configure ROI as follows:

1. Click Enable ROI ZOOM check box, if you want to resize ROI area.

2. Move the square box to specific region or adjust the size of square box if you want.

3. User can configure ROI setting using arrow key to move the position of square box or using scroll

bar to adjust the size of square box.

4. User can

save the ROI as a preset and access to preset position in easy way. First, selects the

preset position and then just click “Go” button.

NOTES

- The ROI setting values in this page are applied as soon as clicking / moving.

- ROI ZOOM function can slow down the performance of the camera

- Click the Save button to save the settings, or click the Reset button to clear all of the information you entered without saving it.

Stream4

The Stream4 features the H.264 compression standard for ROI.

Figure 30. Video & Image / Stream4

H.264 Setting: Configures the H.264 setting value for stream4.