Koden Electronics RB718A, RB717A User Manual

5.5 MENU Operation
+
.75
ECHO
MANU
List of MENU List of Main Menu
MARK
(MAIN-MENU)
EBL1 ON/OFF GAIN AUTO/MAN VRM1 ON/OFF EBL2 ON/OFF GZ ON/OFF FTC AUTO/MAN
VRM2 ON/OFF OFF-C ON/OFF TUNE AUTO/MAN SEL WIN FL EBL2 ON/OFF ST OFF/ST1/ST2 PICTURE DAY/NIGHT
FL VRM2 ON/OFF HDG
OFF ///CSR ON/OFF ZOOM ON/OFF
RINGS ON/OFF SL SHORT/LONG VAR
RNG TARGET +MK LINE
OFF
ON/OFF
ON/OFF
List of Custom Menu
PRESET1 (SUB-MENU) PRESET2 (SUB-MENU)
HM FLSH ON/OFF GZ LEVEL 1-7 STERN M ON/OFF GZ MODE IN/OUT NORTH M ON/OFF HOLD ON/OFF ST’BY NAVI/NOR DISPLAY RDR/MONI/NAV BUZ VOL OFF/LOW/HIGH EXT BUZ OFF / CONT / INT RM UNIT NM / KM / SM IN P/R 1080/1024/2048/4096/360 DEPTH M / FT / FM OUT P/R 1080/1024/2048/4096/360 TEMP EBL BRG REL / TRUE / MAG IR OFF / IR1 / IR2 WP BRG TRUE / MAG SPD SET NMEA / MANU 0.0 KT / LOG 200P HEAD INPUT NMEA / SIN, COS /12BIT / 10BIT LANGUAGE 15 countries HEAD TRUE / MAG SCAN SPEED STD / HIGH +MK MODE DIST/BRG / LAT/LON P TABLE 0 - 2
TIMING ADJ HEAD ADJ TUNING CAL. ANTENNA 1-9 GAIN 1-30 STC 1-16
MAIN-MENU
MODE HU/HS/NU/CU/TM
SLEEP OFF/5min/10min/
°
C / F DEMO ON / OFF
ADJUST (SUB-MENU)
(MAIN-MENU)
(MANU/NMEA)
15min
. 25 HU
ECHO
(MAIN-MENU)
STC AUTO/MAN/HARBOR
TRACK OFF/15SEC/30SEC/
MARK
NAV
ST’BY
ECHO
GAIN >
STC > FTC > TUNE > ST > TRACK ZOOM S/L
1MIN/3MIN/6MIN/ CONT
CPA SET 0.0 NM TCPA SET 0 MIN VECT SET. 6 MIN VECT MODE REL/TRUE ATA ON/OFF
SETUP
AUTO
SETUP
(MAIN-MENU)
WINDOW PPI / SEMI3D+PPI /
PPI+PPI / PPI+NAV / ALL PPI / ALL PPI+PPI / MOB
SYSTEM CHECK CUSTOM KEY ASSIGNMENT
PRESET1 (SUB-MENU) PRESET2 (SUB-MENU) NMEA PRESET ADJUST (SUB-MENU)
ATA PRESET
SUB-MENU
46
.75
MARK
. 75
+
°
xxx
5.5.1 Mark Menu
Setting for markers and cursors
= keys to press
<Common operations for the MARK menu>
(Up to the point when "MARK" menu is selected from the main menu)
Press the "MENU" key and select "MARK" from the displayed 4 main menus using the left-right cursor. (The contents of the selected MENU will appear on a pull-down display in accordance with the movement of the left-right cursor.)
MENU → Left/Right
(Select MARK)
Further explanations on the MARK menu are made assuming that "common operation for the MARK menu" has already been completed.
5.5.1.1 Bearing measurement (EBL1)
(1) Select EBL1 from the pull-down display items using the up-down cursor key, and press the "ENT" key. (2) When the ON/OFF sign is displayed beside the letters EBL1, select ON with the up-down cursor keys and
press the "ENT" key.
.25 HU
>>>
0.23NM
MARK
EBL1 >
VRM1 > EBL2 >
ON
OFF
NAV
ECHO
SETUP
AT
(3) When you press the "ENT" key, an electric bearing
line (EBL1) appears and the angle from the direc-
.25
HU
tion of the ship’s head which is set at 0 degree will
appear in a reverse display in the lower left corner
of the screen. (4) Place the EBL on the center of the target with the
rotary control and read out the bearing. You can use
1 0.0
the EBL functions in the following modes.
(a) Press the "ENT" key to show the EBL1 display still
on the screen. (b) Press the "MENU" key without the EBL1 display. (c) Pressing another function key will lead to the function of that key with the EBL1 display still on the
screen.
Note: 1 xxx.x indicates the relative bearing measured by BL1.
Up/Down → ENT → Up/Down → ENT → Control knob →ENT (a)
(Select EBL1) (Select ON) (EBL1 operation) →MENU
→ Other function key (c)
Note: The displayed EBL angle is the relative bearing to ship’s heading or true bearing against true
north, depending on the setting of "EBL BRG" in the "SETUP" menu.
47
(b)
.75
+
5.5.1.2 Determining the distance (VRM1)
(1) Select VRM1 from the pull-down display items using the
.25 HU
up-down cursor key, and press the "ENT" key.
(2) When the ON/OFF sign is displayed beside the letters VRM1,
select ON with the up-down cursor keys and press the "ENT" key.
(3) If you press the "ENT" key, the variable range marker1 (VRM1)
and its distance in a reverse display appear in the lower left corner of the screen (See Note).
1 0.00NM
(4) To measure the distance to a target, place the VRM1 on the front edge of the target with the rotary
control and read the distance. (5) You can use the VRM1 functions in the following modes. (a) Press the "ENT" key to show the VRM1 display still on the screen (b) Press the "MENU" key without the VRM1 display. (c) Pressing another function key will lead to the function of that key with the VRM1 display still on
the screen.
Up/Down →ENT →Up/Down → ENT →Control knob
(Select VRM1) (Select ON) (VRM1 operation)
→ → → Other function key (c)
ENT (a) MENU
(b)
Note: 1 xx.xx NM indicates VRM1.
5.5.1.3 Bearing measurement (EBL2)
Refer to the section “Bearing measurement (EBL1)”. The "EBL2" will appear in a reverse display in the lower right corner of the screen.
Note: 2 xxx.x indicates the bearing measured by EBL2.
5.5.1.4 Determining the distance (VRM2)
Refer to the section “Determining the distance (VRM1)”. The "VRM2" will appear in a reverse display at the lower right corner of the screen.
Note: 2 xx.xx NM indicates the distance measured by VRM2.
5.5.1.5 Measuring the distance or angle between two points ( FL EBL2, FL VRM2 )
Determining the distance (VRM2)
(a) Preparation for the measurement
(1) Use the up-down cursor keys to select FL VRM2 from the pull-down display items, and press the
"ENT" key.
(2) Use the up-down cursor keys to select ON from the ON/OFF display beside the FL VRM2 items,
and press the "ENT" key. The “SET START POINT” item will be shown and a small cross mark appears. (Once this is set, the "ON" state continues unless any other change is made.)
Up/Down ENT Up/Down ENT ----------------------- FL VRM2 is turned
ON and the small cross
(Select FL VRM2) (Select ON) mark appears.
(b) Setting a reference point for the distance measurement
Use the left-right and up-down cursor keys to place the small cross mark on one of the two echoes whose distance is to be measured, and press the "ENT" key.
Up/Down & Left/Right → ----------------------- ENT Criterion of the reference point is set.
(Place the cross cursor on an echo)
48
.75
Place the VRM2 on other target
.75
To measure the distance
Small cross
mark
FL VRM2 Indication of VRM2
Center of VRM2
(c) Measuring
Perform the operations in the above mentioned "Common operation for the MARK menu" and "measuring the distance(VRM2)", and place the VRM2 on other target. VRM2 will be shown on the screen around the fixed cross cursor.
The distance display " 2 xx. NM" will be shown in the lower right corner of the screen, showing the distance between the two targets.
between two targets
.25
HU
.25
HU
SET START POINT
Note: EBL2 and VRM2 does not follow to "ZOOM" and "OFF-C" function.
5.5.1.6 Measuring the angle between two points (FL EBL2)
(a) Preparation for the measurement
(1) Use the up-down cursor keys to select FL EBL2 from the pull-down display items, and press the
"ENT" key.
(2) Use the up-down cursor keys to select ON from the ON/OFF display beside the FL EBL2 items, and
press the "ENT" key. “SET START POINT” is displayed and a small cross mark appears. (Once this is set, the "ON" state continues unless changes are made.)
Up/Down ENT Up/Down ENT ---------------------- FL EBL2 is turned
ON and (Select FL EBL2) (Select ON) the small cross mark appears.
(b) Setting a reference point for measurement of the angle.
Use the left-right and up-down cursor keys to place the small cross mark on one of the two echoes whose angle will be measured, and press the "ENT" key.
Up/Down & Left/Right -------- ENT Criterion of the reference point is set. (Place the cross cursor on an echo)
(c) Measuring
Perform the operations in the above mentioned "Common operation for the MARK menu" and "measuring the distance(EBL2)", and place the EBL2 on other echo. EBL2 is displayed on the screen based on the placed fixed cross cursor.
" 2 xx. xx" which is displayed at the lower right will be the angle between the two points.
Note: The displayed EBL angle is relative to heading or true to north, depends on the setting of "EBL
BRG" in the "SETUP" menu.
2 0.72NM
49
.75
Not displayed while the ENT key
is held down.
.75
FL EBL2
.75
Origin of EBL2
To measure the angle between two
indication of
small cross mark
cross mark
.75
.25
HU
points
.25
HU
SET START POINT
2 20.3°
5.5.1.7 Erasing heading marker temporarily (HDG OFF)
EBL2
(1) Use the up-down cursor key to select HDG OFF
from the pulled down menu.
(2) Press the “ENT” key to turn off the heading marker,
it stays off as long as you press and hold the key.
.25
HU
Up/Down ENT The heading marker is off as long as you press and hold the “ENT” key down.
(Select HDG OFF)
5.5.1.8 Using parallel cursor (///CSR)
Using the parallel cursor, you can monitor the behavior of other targets whether they are navigating along with the course or, changing their course to someway. (1) Use the up-down cursor key to select ///CSR from the
pull-down menu, and press the “ENT” key (ON/OFF
display beside the ///CSR item). (2) Use the up-down cursor key to select ON. (3) Press the “ENT” key. Parallel cursor will appear on the
screen. As you move EBL, the parallel cursor also
.25
HU
EBL1
moves. To cancel the ///CSR function, select OFF in (2).
Parallel cursor
Up/Down ENT Up/Down (Select ON) ENT ----------------Parallel cursor appears.
(Select ///CSR)
Note: Interval of ///CSR same as fixed range marker. ///CSR moves with EBL1.
→
Up/Down (Select OFF) ENT ------------ Parallel cursor disappears.
50
.75
.75
5.5.1.9 Establishment of the indication of the RANGE RINGS (RINGS)
(1) Press the up-down cursor key to select RINGS from the pull-down menu, and then press the “ENT” key.
(The ON/OFF sign will appear beside the letters RINGS)
(2) Use the up-down key to select ON or OFF and press the “ENT” key
Select ON Range Rings ON Select OFF Range rings OFF
Up/Down ENT Up/Down (Select ON) ENT -------------Range rings appear.
(Select RINGS)
→
Up/Down (Select OFF) → ENT ---------Range rings disappear.
<Number of range rings and range interval>
RA53
Range 0.125 0.25 0.5 0.75
Number of Rings 2 2 2 3 6 6 6 6 6 6 4
Interval 0.0625 0.125 0.25 0.25 0.25
RA54
Range 0.125 0.25 0.5 0.75
Number of Rings 2 2 2 3 6 6 6 6 6 6 6
Interval 0.0625 0.125 0.25 0.25 0.25
1.5 3 6 12 24 48 64
0.5 1 2 4 8 16
1.5 3 6 12 24 48 72
0.5 1 2 4 8 12
.25
HU
.25
HU
Range rings ON
Range rings OFF
5.5.1.10 Variable range function ( VAR RNG )
The range scales are allocated as 0.5--0.75--1.5--3.0--.....as standard. However, using this function, a
consecutive range scaling is also available such as 0.5--0.6--0.7--0.8--..... .
(1) Use the up-down cursor keys to select VAR RNG from the pull down menu and press the "ENT" key. (2) When you select ON with the up-down cursor key from the ON/OFF display beside the VAR RNG item,
and then you press the "ENT" key, the VAR RNG function becomes valid and VAR will be displayed
in the upper left corner of the screen (beside MODE).
Setting procedure
Up/Down ENT Up/Down (Select ON) ENT VAR RNG function is
turned ON.
(Select VAR RNG)
→
Up/Down (Select OFF) ENT VAR RNG function is
turned OFF.
(3) The range changes continuously by pressing the up or down cursor key while the VAR RNG function is
on, and it changes in step with the "RANGE UP" or "RANGE DOWN" key.
Method of use
Up/Down -------------------------------------Range changes continuously RANGE UP & RANGE DOWN ---------Range changes in step
(4) To cancel the vari-range function, press any key except the "RANGE UP" and "RANGE DOWN" keys.
51
.75
.75
+MK POS
+MK POS
5.5.1.11
To output the Cursor ( TARGET ) position data to external equipment
Move the cross cursor with the up-down and left-right keys to the position which position data to be
output.
Use the up-down cursor keys to select TARGET from the pull-down menu, and press the "ENT" key.
The latitude and longitude data of that position will be output to NMEA port with TLL format.
Up/Down ENT output the L/L position of the cursor (Select TARGET)
Note: When you activate this function, nothing happens on the screen.
5.5.1.12
Having the Distance and Bearing markers follow the cross cursor (+MK LINE)
(1) Use the up-down cursor keys to select +MK LINE from pull down menu and press the "ENT" key. (2) Select ON with the up-down cursor key from the ON/OFF display beside the +MK LINE item. (3) Press the "ENT" key to make the +MK LINE function valid, and the distance/bearing marker will be
placed on the cross cursor.
Setting procedure
Up/Down ENT Up/Down (Select ON) ENT +MK LINE function is
turned ON.
(Select +MK LINE)
→
Up/Down (Select OFF) ENT +MK LINE function is
turned OFF.
(4) The distance/bearing markers will follow the cross cursor until +MK LINE function is turned OFF.
.25
HU
.25
HU
230.0°
0.47
+MK LINE OFF
230.0°
0.47
+MK LINE ON
distance/bearing marker follows to cross
The
cursor. EBLs and VRMs can be used separately.
5.5.2 Nav (Navigation) Menu
xxx = keys to press
Radar functions for navigation aid are in this menu.
< Common operations for the NAV menu >
(Up to the point when "NAV" menu is selected from the main menu) Press the "MENU" key and select "NAV" from the displayed 4 main menus using the left-right cursor. (The contents of the selected MENU will appear on a pull-down display in accordance with the movement of the left-right cursor.)
MENU → Left/Right
(Select NAV)
Further explanation about the NAV menu will be conducted on the assumption that this "common operation for the NAV menu" has already been completed.
5.5.2.1 Changing display mode (MODE) (1) Select MODE from the pull-down display items using the up-down cursor key, and press either the
"ENT" key.
52
.75
NAVIGATION
>>>
(2) When the MODE sign is displayed beside the MODE item, select a mode with the up-down cursor keys
and press the "ENT" key. (3) The display mode indicates upper-left on the screen.
.25 HU L
0.23 NM
MARK
NAV
ECHO
MODE >
GZ > OFF-C > SLEEP >
AT
SETUP
HU HS NU CU
TM
UP/DOWN ENT UP/DOWN (Select MODE) (Select HU) ENT HU(Head up) | (Select HS) ENT HS(Head set) | (Select NU) ENT NU(North up) | (Select CU) ENT CU(Course up) (Select TM) ENT TM(True motion)
Note1: Navigation equipment (gyrocompass, magnet compass, or GPS) must be connected to your radar in
NU, CU and TM modes.
Note2: In TM modes it is necessary to set as follow (1) or (2).
(1) Input of speed information from NMEA. (2) Set your ship’s speed manually.
Note3: TM mode is only available on single PPI screens (PPI and All PPI modes). If the screen type in TM
mode switches to dual PPI modes, such as PPI/PPI and Semi 3D/PPI, the TM screen mode will be automatically changed to NU mode.
5.5.2.2 Setting the Guard Zone (GZ)
The following procedure sets up the distance, depth and the width of the guard zone. Once set, the guard zone detects the existence of echoes exceeding a prefixed level and then generates an audio alarm (IN MODE) or, it detects non-existence of echoes that has left the guard zone (OUT MODE).
(1) Select GZ from the pull-down menu using the up-down cursor keys, and press the “ENT” key.
The ON/OFF sign is displayed beside the letters GZ.
Up/Down ENT ON/OFF sign is displayed.
(2) Select “ON” by “common operation for the GZ menu”,
and press the “ENT” key.
53
GZ IN
SET CENTER POINT
expands and contracts with respect to the cross
cursor position.
The mode (IN or OUT) is displayed when the state is ON. Nothing
(3) The GZ IN sign appears in the left side of the screen,
showing the present mode setting. A small cross cursor appears on the screen center for setting up the guard zone. A prompt "SET CENTER POINT appears at the bottom, requesting to define the center of the guard zone.
(4) Move the cross cursor to the center of the warning zone to be set, using the up-down and left-right
cursor keys, and then press the "ENT" key. The guard zone appears now.
(5) From the cross cursor position as set in step (4), expand the guard zone as follows.
GZ IN
Use the right cursor key to enlarge the guard zone width and left cursor key to contract the width using the left cursor. The guard zone
is displayed when it is OFF.
(6) After setting the guard zone, fix it by pressing the "ENT" key.
To cancel the guard zone function, select “OFF” by “common operation for the GZ menu”, and press the “ENT” key.
ENT →
Up/Down & Left/Right
ENT
Up/Down & Left/Right
ENT
-------------------------------- Setting completed
(Setting the center of GZ) (Setting the scope of GZ)
Stop the alarm tone
To momentarily silence the audio alarm, press any key on the control panel. In this state, the guard zone function is still operative. To permanently turn off the guard zone function, select "OFF" from the GZ menu.
Note1: To switch the IN or OUT mode, refer to “Guard Zone Mode” in section 5.5.4.5.3 “Changing the
content of settings 2 (PRESET2)”
Note2: To set the guard zone level, refer to “Guard Zone LeveL” in section 5.5.4.5.3 “Changing the content
of settings 2 (PRESET2)”
5.5.2.3 Shifting display in specific direction (OFF-C)
Displaying the location specified by the cross cursor as the vessel's location.
(1) Select OFF-C from the pull-down display items using up-down cursor key, and press the "ENT" key. (2) When the ON/OFF sign is displayed beside the OFF-C item, select ON with the up-down cursor keys
and press the "ENT" key.
(3) OFF-C is displayed in the upper right corner of the screen and "SET OFF CENTER POINT" at the
bottom of the screen, and setting is ready to be entered. Move the cross cursor with the cursor keys to move own ship’s position to an intended location, and press the "ENT" key. Own ship’s position will be moved to cursor's location. The reversed OFF-C sign will be put back to normal display, indicating the off-centered screen is now set up.
(4) To cancel “OFF-C” function, either select OFF in (2)
54
.
75
.
75
Up/Down ENT Up/Down (Select OFF-C) |(Select ON) ENT Left/Right & Up/Down ENT -------Set OFF-C (Select OFF) ENT ------------------------------------- Cancel OFF-C
Note: The VRM2 and EBL2 do not follow the OFF-C function while they are floated. The function operates only on PPI screen.
.25
HU
Move the cross cursor
.25
HU
indicates "OFF-C" state is entered
OFF-C
SET OFF-C POINT
5.5.2.4 Setting of the SLEEP function(SLEEP)
This function allows a 30-second-transmission during pre-fixed times. Following the transmission cy­cle, a power-saving mode will be activated with the screen display put into ST'BY state (the scanner-OFF state) and the LCD backlighting turns off, accordingly. This action is repeatedly executed. For practicing purpose, set a guard zone and have the warning signal automatically activated every prefixed period.
(1) Use the up-down cursor keys to select SLEEP from the pull-down menu, and press the "ENT" key. (2) When the OFF/5min/10min/15min display appears beside the SLEEP item, select a time to be set with
the up-down cursor keys. (3) Press the "ENT" key to complete the setting. To cancel the SLEEP function, select OFF in step (2).
After setting a SLEEP mode, a transmission takes place and 30 seconds later the ST'BY state is estab­lished, turning the backlight off. (Power-saving mode). Two minutes before the prefixed time the backlight turns on again and the 2-minute timer starts. Then, at the fixed time another 30-second-transmission starts. This series of actions are repeated. If you press any key during the course of this action, the SLEEP function will be canceled.
(a) Setting procedure
Up/Down → ENT → Up/Down →(Select OFF)
ENT ------------------------------ SLEEP function is turned OFF
(Select 5min.) →
(Select SLEEP)
Transmission Setting completed
(Select 10min.) →
(Select 15min.) →
ENT → POWER ------- 30-second-transmission every 5 min. ENT → POWER ------30-second-transmission every 10 min. ENT → POWER ----- 30-second-transmission every 15 min.
(b) Action after setting
SLEEP setting ( 5min. ) (Operation) |
(Under Tx) ^ (Under power-saving mode)
^
0 sec. 30 sec. 3 min. 5min. 5and a half min. (Time used)
TX Start TX OFF Backlight ON Tx Start TxOFF (Action) Countdown start
(2min. timer in use)
^
55
(Under Tx) ^ (Under power-saving mode)
^
G 35
.7 5
ECHO
>>>
MANU
AUTO
-- What happens if a key is pressed after a SLEEP mode setting?
If a transmission has started and you press a key after setting a SLEEP mode, power-saving mode will be activated 30 seconds after a key is pressed.
-- What happens if a key is pressed during the SLEEP mode?
a) If you press a key during the power-saving mode, the SLEEP function will be canceled and
the 2-minute timer starts.
b) If you press a key while the 2-minute timer is in active, or during transmission, the SLEEP
function will be canceled.
5.5.3 Echo Menu
This pull-down menu provides various pre-settings for the radar PPI video shown on the screen.
<Common operations for the ECHO menu >
Press the "MENU" key and select "ECHO" from the displayed 4 main menus using the left-right cursor.
All items of the ECHO menu will be shown in a pull-down form as shown below.
MENU Left/Right
(Select ECHO)
(1) Use the up-down cursor keys to select GAIN from the pull-down display items, and press either the
"ENT" key or the right cursor key.
(2) Select MENU from the MANU/AUTO display beside the GAIN item using the up-down cursor keys,
and press the "ENT" key.
(3) The present state of GAIN is displayed in reverse form on the
left side of the screen as G 35 , showing the gain setting is ready for entry.
(4) Turn the rotary control, observing the screen. The figure shown
on the screen changes within a range of 0 and 99.
(5) The GAIN adjustment completes by pressing the "ENT" key
after the setting.
When you wish to enter the AUTO function, select AUTO
in step (2) and press the "ENT”.
Up/Down ENT → Up/Down
.2 5 HU L
0.23 NM
5.5.3.1 Sensibility adjustment (GAIN)
MARK
NAV
ECHO
GAIN >
STC > FTC > TUNE > ST >
SETUP
The setting value is displayed during MANUAL op­eration. AT is displayed during AUTO operation. (The same applies to STC, FTC and TUNE.)
xxx = Keys to press
AT
(Select GAIN) |(Select MANU) Control knob ENT ------------Set to MANU mode | (GAIN adjustment) |(Select AUTO) ENT -----------------------------------Set to AUTO mode
56
5.5.3.2 Removing sea clutter (STC)
Refer to the section, “Sensibility adjustment (GAIN)”.
Up/Down ENT Up/Down
(Select STC) |->(Select MANU) ENT Control knob ENT - Set to MANU mode | (STC adjustment) |->(Select AUTO) ENT ------------------------------------Set to AUTO mode
Note: When you select the MANU mode, the GAIN and FTC functions will be switched to MANU mode,
too.
Note: When you select the HARBOR mode, FTC will be switched to MANU mode.
5.5.3.3 Removing rain and snow clutter (FTC)
Refer to the section, “Sensibility adjustment (GAIN)”.
Up/Down ENT Up/Down
(Select FTC) |->(Select MANU) ENT Control knob ENT -- Set to MANU mode | (FTC adjustment) |->(Select AUTO) ENT ------------------------------------Set to AUTO mode
5.5.3.4 Adjusting the receiver tuning (TUNE)
Refer to the section, “Sensibility adjustment (GAIN)”.
Use the following key operations to set up the tuning.
Up/Down ENT Up/Down
(Select TUNE) |->(Select MANU) ENT Control knob ENT ---- Set to MANU mode | (TUNE adjustment) |->(Select AUTO) ENT ------------------------------------Set to AUTO mode
35
Indicated setting value on manual mode, AT on auto mode
5.5.3.5 Echo expansion (ST)
This function stretches the echo towards range, for easy recognition of the target on the screen.
Two types of the echo expansion is available. Select ST1 or ST2 from the menu. (1) Use the up-down cursor keys to select ST from the pull-down display items, and press the "ENT" key. (2) Select ST1 or ST2 from the display beside the ST item using the up-down cursor keys, and press the
"ENT" key.
Up/Down
ENT
Up/Down
(select ST1) ENT set ST1 | (select ST2) ENT set ST2 | (select OFF) ENT ST OFF
57
.75
+
.75
+
.75
+
( expansion rate ST1<ST2 )
.25 HU
.25 HU
ST1
ST function is OFF
ST1, or ST2 display, no display on OFF state
The picture to display echoes expanded in the direction of the distance
5.5.3.6 Displaying the target track (TRACK)
(1) Use the up-down cursor keys to select TRACK from the pull-down display items, and press the "ENT"
key.
(2) Select 15SEC, 30SEC, 1MIN, 3MIN, 6MIN, or CONT from the display beside the TRACK item using
the up-down cursor keys, and press the "ENT" key.
(3) If you select 15SEC, the sign "TRK 15S" appears on the left side of the screen, entering the assigned
track interval. The “TRK 15S” indicates the length of the track, displaying a 15-second-long sailing track at maximum.
Note: When PPI+PPI or ALL PPI+PPI screen mode is used, TRACK function can be used
only on CONT mode.
Tracks of target
.25 HU
Present echo
moving direction
TK 15SEC
disappears after selected time
the length of the track
The key sequence for setting up the ship’s track
up/down ENT up/down (select OFF)ENT TRACK OFF |(select 15SEC)ENT set 15sec. track |(select 30SEC)ENT set 30sec. track |(select 1MIN) ENT set 1 min. track |(select 3MIN) ENT set 3 min. track |(select 6MIN) ENT set 6 min. track |(select CONT)→ ENT set continue track
5.5.3.7 Enlarging the selected areas (ZOOM)
Using this function, you can enlarge the selected zone around the cross cursor twice as large as the one displayed on the screen. (1) Use the up-down cursor keys to select ZOOM from among the pull-down display items, and press the
"ENT" key. (2) Select the ON using up-down cursor keys from the ON/OFF display beside the ZOOM item, and press
the "ENT" key.
58
.75
+
.75
.75
(3) A small cross cursor and the prompt "SET ZOOM POINT" will be displayed on the screen center and at
the bottom respectively.
(4) Use the cursor keys to move the cross cursor to the point to be magnified, and press the "ENT" key to
complete the setting. The area around the cross cursor is displayed in 2x magnification, with blinking "ZOOM" displayed in the upper right corner of the screen, indicating that a ZOOM display is shown.
(5) To cancel the ZOOM function, select OFF in step (1) or begin operation of range.
Up/Down ENT Up/Down (Select ON) ENT Up/Down & Left/Right ENT ZOOM
Setting (Select ZOOM) | (Move cross cursor)
| (Select OFF) ENT ---------------------------------------ZOOM canceled
Note 1) VRM2 and EBL2 do not follow the ZOOM function during they are floated. Note 2) Normal screen returns when you change the range scale. Note 3) ZOOM function is usable only in PPI screen mode. Note 4) ZOOM function is unusable in OFF-C. Note 5) The ZOOM center can be set any desired position within the set range.
.25 HU
.25 HU
blinking "ZOOM"
ZOOM
SET ZOOM POINT
5.5.3.8 Increasing the sensitivity (S/L)
The pulse length is automatically changed as you change the range scale. However, if you wish to in­crease the sensitivity or to improve the picture definition, change the pulse length according to your need. If you select the short pulse (SHORT), the picture will become more definite, giving higher range discrimina­tion. If you select the long pulse (LONG), the picture will be stretched towards range, providing better rec­ognition of the targets shown, in contrast, the range discrimination will be sacrificed.
(1) Use the up-down cursor keys to select S/L from among the pull-down display items, and press the "ENT"
key.
(2) Select Pulse length (SHORT or LONG) using the up-down
cursor keys from the SHORT/LONG display beside the S/L item.
.25 HU S
S or L display
(3) The setting will be completed when the “ENT” key is
pressed after the selection.
Up/Down ENT (Select SHORT) ENT ------------------------- Set to short pulse |(Select LONG) ENT -------------------------- Set to long pulse
59
. 75
SETUP
>>>
5.5.4 SETUP Menu
Using this menu, you can select and set up the following picture presentation modes: (1) PPI: A basic presentation mode composed of a complete PPI screen, with status displays on the left side, and an array of the soft keys on the right side of the screen. (2) SEMI3D/PPI: A small complete PPI on the left side and a semi-3D screen on the right side. (3) PPI/PPI: Two small complete PPI screens on both sides, with the status display and the soft keys at the bottom and in the right side, respectively. (4) PPI/NAV: A small PPI screen on the left side and the NAV information on the right side. The status display and an array of the soft keys are positioned at the bottom and in the right side of the screen, respectively. (5) ALL PPI: A single, largest PPI screen is shown. The top and the bottom parts of the PPI screen are truncated, while the right and left sides of PPI are fully displayed. (6) ALL PPI/PPI: Two larger PPI screens with truncated bottom. (7) MOB: A Nav display, showing the position of MOB (Man Over Board) and present ship’s position in latitude and longitude coordinate.
<Common operations for the SETUP menu> (Up to the point when "SETUP" menu is selected from the main menu)
Press the "MENU" key and select "SETUP" from the displayed 4 main menus using the left-right cursor. (The contents of the selected MENU will appear on a pull-down display in accordance with the movement of the left-right cursor.)
MENU → Left/Right
(Select SETUP)
Further explanation about the SETUP menu will be conducted on the assumption that this "common operation for the SETUP menu" has already been completed.
5.5.4.1 Selecting and setting up the screen mode (WINDOW)
(1) Use the up-down cursor keys to select WINDOW from among the pull-down display items, and press the
"ENT" key.
(2) Select a screen to be displayed with the up-down cursor keys from among the above 7 items shown beside
the WINDOW item.
(3) The setting will be completed when you press the "ENT" key after the selection.
.25
HU
0.23NM
MARK
NAV
PPI
SEMI3D / PPI PPI / PPI PPI / NAV ALL PPI ALL PPI/PPI MOB
ECHO
SETUP
WINDOW >
SEL WIN > PICTURE > SYSTEM CHECK CUSTOM >
AT
60
.75
PPI Screen
Up/Down → ENT
(select WINDOW)
Up/Down
(Select PPI)
(Select PPI+SEMI3D) → ENT (b)
(Select PPI+PPI)
(Select PPI+NAV)
(Select ALL PPI)
(Select ALL PPI+PPI) → ENT (f)
(Select MOB)
ENT (a)
ENT (c)
ENT (d)
ENT (e)
ENT (g)
-Available functions on each screen mode
SCREEN ITEM RANGE VRM1, EBL1 VRM2, EBL2 FL VRM2/EBL2 RINGS ON/OFF ZOOM, OFF CENT ///CSR HDG OFF STERN M NORTH M GAIN, STC, FTC TUNE ST GZ SEL WIN X X TXON/OFF
PPI PPI/SEMI3D
PPI+PPI ALL PPI ALL PPI PPI
PPI/NAV
¡
¡
¡
X X X X X
¡
¡
X X X X X
¡
¡
¡
¡
¡
¡
¡
¡
¡
¡
¡
¡
¡
¡
¡
¡
¡
¡
¡
¡
¡
¡
¡
¥
X X X
o
X X X
o
¡
o
X
¡
¡
¡
X X X
¥
X X X
¡
X X X
¡
X X X
¥
X
¡
¡
¡
¡
¡
¡
¡
¡
X
¥
X
¡
X
¡
X
¡
X
¡
X
¡
X
¡
X
¡
: The control available on active screen only. To use the function on another
¥
screen, switch the active screen using the SEL WIN function.
: Simultaneous control is possible for dual screen.
¡
: The function is available only on PPI screen.
o
X : The function not available.
- Screen modes and Operations
(a) PPI Screen
All functions can be used on this screen.
.25 HU
+
(b) PPI/SEMI3D Screen
MOB
61
.75 .25 HU
+
PPI/SEMI3D Screen
.75
25
LEFT screen selected
.75
25
24
F 35/AT
LEFT GAIN is ac
tive
Left GAIN in reverse
picture drawing(refreshed)
displayed previous picture ( held)
All controls, such as EBLs, VRMs are active on both screen. The functions such as ZOOM, OFF-C, FL EBL2, and FL VRM2 are not availabel in this mode. In the "SEMI3D" screen, ship's heading direction always stays on the center vertical line denoted 000.
280 320 000 040 080
(c) PPI/PPI Screen
Each radar screen is updated one then the another on every two antenna scans, as shown in the
following illustration. The unupdated picture remains frozen while another screen is in process.
.
HU S 24 6
.
HU S
6
+
+
G 55/35 S 35/AT F 35/AT
Note: When your ship navigates at high speed, use a single PPI screen mode to obtain faster picture
update.
Note: Functions including ZOOM, OFF-C, FL-EBL2, and FL-VRM2 are not available in this screen mode. Note: The functions including RANGE, GAIN, STC, FTC, and GZ can be used independently for each
screen. The screen with reversed range display, as selected in "SEL WIN", is an active display, in which you can operate available functions.
Note: The cross cursor will be displayed only on a selected screen.
-Operation
LEFT screen /--------/*******/--------/******/--------/****** t RIGHT screen *******/--------/******/--------/******/--------/
a) Changing the RANGE scale in LEFT screen
1) When the RIGHT range scale indicator is reversed, use the "SEL WIN" function to make the LEFT screen to be active.
2) Press the ”RANGE UP” or ”RANGE DOWN” key to change the RANGE scale.
G 55/35
S 35/AT
62
1 0.00NM
1 0.00NM
Determining the distance with VRM1
.75
6
+
NAV DISPLAY
.75
. 75
ALL PPI screen
b) Adjusting GAIN of LEFT screen.
1) When the RIGHT range indicator is displayed reverse, use the "SEL WIN" function to make the LEFT screen to be active.
2) Press the "GAIN" key and the letters "G50" will be displayed in reverse, indicating the GAIN adjustment is available.
3) Adjust GAIN with the rotary control.
Adjust STC and FTC in the same manner as GAIN.
Note: While the adjustment of GAIN, STC, or FTC is in process, the radar picture update will be
frozen. In approximately 5 seconds after the adjustment, the radar picture update will be resumed.
c) Using VRM1 on LEFT screen.
1) When the RIGHT range indicator is displayed in reverse,
.25 HU S
1
change the active screen to LEFT screen with "SEL WIN" function.
2) Press the "VRM1" key and " " will be displayed in
+
reverse, indicating the VRM1 is available.
3) Rotate the rotary control to measure the distance.
4) The same procedure applies to VRM2, EBL1, or EBL2.
NOTE: To use the VRM1 on the RIGHT side screen, first
G 55/35 S 35/AT F 35/AT
switch the active display to RIGHT side, then press the VRM1 key.
on LEFT screen
(d) PPI/NAV Screen
Note: The ZOOM, OFF-C, FL EBL2, and FL VRM2 are
not available in this screen mode.
.25 HU S
WAY P 123.4°
6.8NM COURSE 2.38NM XTE <<< HDG 267.3°T
SPD 12.8 TEMP 20.8°C DEPTH 58.3 LAT/LON 34°08. 22N 138°02. 53E
KT
M
PPI/NAV screen
(e) ALL PPI Screen
Note1: The status display such as RANGE, RINGS interval, and
Display mode are displayed in the upper-left corner of
. 25 HU S
the screen.
Note2: When you press any key except "MENU", "RANGE
UP/DOWN", "BRILL", and "POWER", the screen will
+
return to the PPI mode.
63
ALL PPI PPI screen
.75
Range display on the active screen become a reverse display
(f) ALL PPI/PPI Screen
.25 HU S 6 1
Note1: The RANGE, RINGS interval, and Display mode are shown on
top of the screen.
Note2: When you press any key except "MENU", "RANGE
UP/DOWN", "BRILL", and "POWER", the screen will return to PPI/PPI mode.
+
Note3: Each radar picture is updated every two antenna scans. The right screen picture is frozen while the left screen is updated, and vice versa. When your ship navigates at high speed, use a single PPI screen to obtain faster picture update.
(g) MOB Screen
The MOB key has been pressed, the MOB position and ship's position are displayed. If not, MOB position will be displayed with bars( --.- )
Press MOB key to clear the MOB position and return to previous screen. Press ENT key to return previous screen with keeping the MOB position data.
MOB POS 37°08. 42N 142°03. 33E SHIP’S POS 37°12. 42N 142°04. 33E
PRESS MOB KEY TO DATA CLEAR PRESS ENTER KEY TO RETURN
MAN OVERBOARD
5.5.4.2 Switching screens on PPI/PPI screen ( SEL WIN )
Switching to the desired screen for activation on a PPI/PPI screen display.
The "SEL WIN" function switches the activated screen to effect the operation such as, RANGE, GAIN, STC, FTC, VRM1/2, EBL1/2, and guard zone. The range indicator of activated screen is displayed in reverse.
When "SEL WIN" is selected with the up-down cursor keys from among the pull- down display items and the "ENT" key is pressed, activated screen will be changed to the opposite screen.
Up/Down ENT the opposite screen activated
(select SEL WIN)
.25 S
.75
.5
.25
.75 .25 HU S
.5 .25 .
64
75
. 75
RNG U RNG D BRILL AUTO
GAIN STC
FTC 1 2 3 4
5 6
7
MOB
POWER
SYSTEM CHECK screen
ENT MENU
CONTROL KNOB
j) Magnetron current
5.5.4.3 Changing the color of screen (PICTURE)
Changing the color of screen depending on weather and day / night environment conditions will be
effective for easy viewing .
When "PICTURE" is selected with the up-down cursor keys from among the pull- down display items, select "DAY" and press "ENT" key to set to day display. Night display appears if "NIGHT" is selected
Up/Down ENT → Up/Down → (select DAY) → ENT → day display
(select PICTURE) (select NIGHT) ENT night display
. 25
HU
. 25 HU
DAY display
NIGHT display
Blue Yellow White Black Green Red
5.5.4.4 Fault Diagnosis by Self Check (SYSTEM CHECK)
Verifying the problem point by SYSTEM CHECK when, for example, some abnormality has occurred. (1) Select SYSTEM CHECK from the pull-down display items using up-down cursor key, and press the
“ENT” key. (2) The system check screen will appear.
SYSTEM CHECK
MEMORY CHECK
a) ROM--------------------------------------- > ROM OK b) RAM----------------------------------------> RAM OK c) Backup memory----------------------- > BACKUP OK
SIGNAL CHECK
d) Transmit trigger ----------------------- > (1) TRIGGER OK e) Bearing pulse -------------------------- > (2) AZIMUTH OK f) Heading pulse -------------------------- > (3) HM OK g) +5Vvoltage(at video circuit)----- > (4) +5V OK 5.2V h) High voltage(at scanner)---------- > (5) H.T. AT SU OK 253.2V i) High voltage(at display)------------- > (6) H.T. AT DU OK 253.2V
k) Tuning voltage------------------------- > (8) TUNE OK
l) Motor power (6 kW/12 kW only)-----> (9) MOTOR OK 40.0 V
m) Cumulative usage time --------> HOURMETER Operation time --------------------- > OPERATE 12.0H Transmit time ---------------------- > TRANSMIT 10.3H
n) ROM version ------------------------> ROM VERSION V1.00 o) Scanner type------------------------> 4 KW OPEN
PRESS POWER KEY TO RETURN
---------------------> (7) MAG. CUR. OK 2.1
TGT N
ACQ
Indicates the cursor status.
p) Indicates the operation status of front-panel keys.
Indicates the control knob status.
65
While watching the screen , check the following:
i) Whether all items are marked “OK”. (If any item is marked “NG”, the indicated location may be
faulty.) ii) Press a front-panel key and see if the corresponding display on the screen is highlighted. iii) Turn the control knob and see if the lower-right indicator move to right or left.
(3) Press the POWER key to return to the previous screen
a) ROM Indicates the ROM status. b) RAM Indicates the RAM status. c) Backup memory Indicates the backup memory status. d) Transmit trigger Indicates the signal line status for the trigger signal sent from the scanner
unit.
e) Bearing pulse Indicates the signal line status for the bearing signal sent fron the scanner
unit. f) Heading pulse Indicates the signal line status for the bow signal sent from the scanner unit. g) +5V voltage Indicates the reference voltage status of the video circuit and its voltage
value. (at video circuit) (normally about 5 V) h) High voltage(at SU) Indicates the status of the high voltage supplied from the display unit to the
scanner unit and its voltage value (normally about 250 V) at scanner unit. i) High voltage(at DU) Indicates the status of the high voltage supplied from the display unit to the
scanner unit and its voltag value (normally about 250 V) at display unit. j) Magnetron current Indicates the status of the anode current flowing in the magnetron and its
current value.
k) Tuning voltage Indicates the status of the voltage used for tunning and its voltage value. l) Motor Indicates the status of the scanner motor power (normally about 40 V) m) Cumulative usage time Indicates the cumulative time your radar is used.
OPERATE : Duration of time during which the power supply is turned on. TRANSMIT : Duration of time transmitting.
n) ROM version Indicates the ROM software version. o) Scanner type Indicates the Scanner type ex. 4 KW OPEN p) Front-panel keys As you press any front-panel key when the SYSTEM CHECK screen is on,
the corresponding key is highlighted on the screen by displaying it in reverse
video.
66
CUSTOM
>
.75
SETUP
5.5.4.5 Changing the content of the setting (CUSTOM)
Note) The items included in the CUSTOM menu are the settings and adjustments to be carried out during installation. These items are not required during normal operations.
-Common operations for CUSTOM
Use the up-down cursor keys to select CUSTOM after ”the common operations for the SETUP” menu, and press the "ENT" key.
MENU Left/Right Up/Down ENT
(Select SETUP) (Select CUSTOM)
Common operation for SETUP When the above operations are completed, the following 4 items will be displayed beside the CUSTOM item, namely "KEY ASSIGN", "PRESET1", "PRESET2" and "ADJUST". Further explanation concerning the CUSTOM menu items will be made assuming that the above "common operations for CUSTOM" have already been conducted.
.25 HU S
>>>
0.23NM
MARK
NAV
KEY ASSIGN PRESET1 PRESET2 NMEA PRESET
ADJUST >
ADJUST >
ATA PRESET
ECHO
WINDOW > SEL WIN > PICTURE > SYSTEM CHECK
CUSTOM >
SETUP
AT
67
5.5.4.5.1 Changing the settings of the soft keys (KEY ASSIGN)
To change the function settings that have been assigned to soft keys, numbered 1 to 7, use the fol-
lowing procedures.
(1) Screen display for the setting
KEY ASSIGNMENT
MARK o EBL1
NAV
o
o
VRM1
o
EBL2
o
VRM2
o
FL EBL2
o
FL VRM2
o
HDG OFF
o
///CSR
o
RINGS
o
VAR RNG
o
TARGET
o
+MK LINE
o
MODE
o
GZ
o
OFF-C SLEEP
ECHO o TUNE
SETUP o SEL WIN
ATA
o
ST
o
TRACK
o
ZOOM
o
S / L
o
PICTURE
o
PPI
o
PPI/3D
o
PPI/PPI
o
PPI/NAV
o
ALL PPI
o
ALL PPI2
o
NEXT
o
DATA
o
DEL
o
ALL DEL
EBL1 EBL2 DATA PPI
VRM1 VRM2 DEL PPI/3D
VAR RNG FL EBL2 ALL DEL PPI/PPI
TRACK FL VRM2 TRACK PPI/NAV
TARGET GZ ZOOM ALL PPI
SEL WIN OFF-C PICTURE ALL PPI2
NEXT NEXT NEXT NEXT
SET1 SET2 SET3 SET4
Key Groups Move with up-down cursor Move with right-left cursor
Mark is displayed when the function is set to a key. Operation panel Keys 1 - 7
Soft Key Setting Screen
Select KEY ASSIGN from the CUSTOM items and press the "ENT" key. The following screen will be shown. (See chart below)
(2) Selecting functions
Reverse the items to be set using the up-down cursor keys. (The items become reverse in accordance with the moving cursor.)
(3) Key settings
(3)-1 Allocating a new function to a soft key (Example 1)
Upon reversing the item with up or down key, press the key to be allocated. The selected item will be displayed beside the key, which indicates that the setting has been completed.
(3)-2 Changing the function of a key with an preset function (Example 2)
When the allocated key is pressed, its function will be altered to the one selected in (1) above and the previous function will be canceled. The current setting item numbers as SET1-4 are always displayed below the letters NEXT. In order to switch the settings SET1-4, use the right-left cursor keys. NOTE: Double settings, setting 1 item for more than 1 key, are possible.
When you wish to assign the functions for more than 1 key, repeat the operations (3)-1 to (3)-2. (Example 3)
1
2
3
4
5
6
7
68
(4) To complete the settings
After you have finished the settings, press the ENT key to exit from KEY ASSIGNMENT.
Example of an operation
(The process up to the selection of KEY ASSIGNMENT from the SETUP menu is omitted. Only the process after the above chart will be described.)
Example 1) Changing the OFF-C function, allocated to key 6 in setting 2, to the HDG OFF function.
Up/Down 6 ENT ---------------Key 6 altered from
Select HDG OFF The display beside key 6 Exit from OFF-C to HDG OFF changes to HDG OFF KEY ASSIGNMENT
Example 2) Re-allocate SEL WIN to key 1 in setting 2.
Left/Right Up/Down 1 ENT Key 1 in setting 2
From SET1 Select SEL WIN SEL WIN is displayed is altered to SEL WIN. to SET2 beside key 1. Exit from KEY ASSIGNMENT
Example 3) Changing the ST function, allocated to key 1 in setting 1, to HDG OFF and then reset the key 1 in setting 2 as SEL WIN.
Up/Down 6 Key 6 altered from
Select HDG OFF The display beside key 6 ST to HDG OFF
changes to HDG OFF
Left/Right Up/Down 1 ENT Key
Select SEL WIN SEL WIN is displayed Exit fromis altered to SEL WIN From SET1 beside key 1. KEY ASSIGNMENT to SET2
69
j) WayPoint Mode
Heading Marker
Stern Marker
.75
5.5.4.5.2 Changing the content of settings 1(PRESET1)
(1) Select PRESET1 from CUSTOM items and then press the "ENT" key to show the PRESET1 screen
(See chart below).
(2) Select the item with up or down key and then contents with left or right key.
The selected item will be enclosed by a rectangular and the contents will appear in reversed display. (a) Repeat the above procedures for the rest of settings.
a) Heading Flash b) Stern Mark c) North Mark d) ST'BY screen e) Buzzer Volume f) VRM Unit g) Water temperature h) Depth Unit i) EBL Mode
k) Heading Input l) Heading Type m) Cursor position n) TX Pulse
(b)
(3) After the setting is completed, exit from the PRESET1 screen with the "ENT" key.
PRESET1
HM FLASH ON _OFF_ STERN M ON _OFF_ NORTH M ON _OFF_ ST’BY _NAVI_ NOR BUZ VOL OFF LOW _HIGH_ RM UNIT _NM_ KM SM TEMP °C_ °F DEPTH _M_ FT FM EBL BRG _REL_ TRUE MAG WP BRG _TRUE_ MAG HEAD INPUT _NMEA_ SIN/COS 12BIT 10BIT
HEAD TRUE _MAG_ +MK MODE _DIST / BRG_ LAT / LON
P TABLE 0 _1_ 2
.5 .75 1.5 3 6 P TABLE _1_ SHORT 0 0 0 1 1 LONG 0 1 1 2 2
PRESS ENTER KEY TO RETURN
Note) The contents will be displayed in (b) together with the numbers selected in P TABLE.
a) HM Flash ON/OFF To Set up HM presentation mode, either FLASH or CONTINUOS. ON: Heading Mark flashes every time the antenna is directed to ship’s bow. OFF: Heading Marker is continuously shown. b) Stern Mark ON/OFF To turn ON or OFF the Stern Mark. c) North Mark ON/OFF To turn ON or OFF the North Mark. d) ST'BY screen To set up the stand-by screen
mode as follows:
.25 HU
NAVI: Navigation Data screen NOR: Normal screen
e) Buzzer Volume To set up audio sound level of
electronic buzzer
f) VRM Unit To select VRM distance unit
NM: Nautical mile
(a)
70
<=
0.75 NM
SHORT
LONG
0.75 NM
0.75 NM
KM: Kilometer
SM: Statute mile g) Water temperature To select water temperature unit C: Celsius F: Fahrenheit h) Depth Unit To select Depth unit
M: Meter
FT: Feet
FM: Fathom i) EBL Mode To select Mode of EBL
REL: Relative bearing from HM
TRUE: True bearing
MAG: Magnetic bearing j) WayPoint Mode To select WayPoint bearing mode
TRUE: True bearing
MAG: Magnetic bearing k) Heading Source To select the source of bearing information.
NMEA
SIN/COS: Compass Data with SIN/COS signal
12BIT: Compass Data with 12bits serial signal
10BIT: Compass Data with 10bits serial signal l) Heading Type Heading Information Type setting
MAG: Magnetic bearing
TRUE: True bearing m) Cross cursor position display Mode
DIST/BRG: Range and Bearing indication
LAT/LON: Latitude and Longitude indication n) Transmitting pulse width Pulse length setting for Range Scale (Note: )
Note: P TABLE
PULSE TYPE
P TABLE 0
P TABLE 1
P TABLE 2
Note: Pulse width 0 : 0.08 uS, 1 : 0.3 uS, 2 : 0.6 uS, 3 : 1.0 uS
0 0 0 1 1 2 3
PULSE TYPE <=0.25 NM 0.5 NM
SHORT 0 0 0 0 1 1 3
LONG 0 0 1 1 2 2 3
PULSE TYPE <=0.25 NM 0.5 NM
SHORT
LONG 0 1 1 2 2 3 3
0.25 NM 0.5 NM
0 0 0 0 0 1 3
0 0 0 1 1 2 3
1.5NM 3 NM
1.5NM 3 NM
1.5NM 3 NM
6 NM >=12 NM
6 NM >=12 NM
6 NM >=12 NM
71
j) Ship's Speed
5.5.4.5.3 Changing the content of settings 2 (PRESET2)
Refer to the section, “Changing the content of setting 1(PRESET1)”.
a) Guard Zone Level b) Guard Zone Mode c) Hold d) Display Unit Mode e) External Buzzer f) Bearing pulse/rot(IN) g) Bearing pulse/rot(OUT) h) Built-in Simulator i) Interference Rejection
k) Indication Language
l) Scan speed m) Color
PRESET2
GZ LVL 1 2 3 4 5 6 7 GZ MODE I N OUT HOLD ON OFF DISPLAY RDR MONI NAVI EXT BUZ OFF CONT INT IN P /R 1080 1024 2048 4096 360 OUT P/R 1080 1024 2048 4096 360 DEMO ON OFF IR OFF IR1 IR2 SPD SET NMEA MANU 0.0KT LOG 200P LANGUAGE CHI DAN ENG FRE GER GRE ITA JPN KOR NOR POR RUS SPA SWE TUR SCAN SPEED STD HIGH COLOR MONO MULTI
PRESS ENTER KEY TO RETURN
a) Guard Zone Level Guard Zone Detection Level setting
1: High Sensitivity, .. 7: Large Target Only
b) Guard Zone Mode Guard Zone Detection Mode setting
IN: To detect entry of a target OUT: To detect leaving of a target c) Hold To hold the radar picture presentation for 30 seconds after
switching to ST'BY
The EBL and VRM can be used in HOLD state.(Note1: ) d) Display Unit Mode Display Unit Operation Mode setting
RDR: Radar mode (normal)
MONI: Monitor mode (for slave display use)
NAV: Navigation mode (for DATA indicator use) e) External Buzzer External Buzzer control setting
OFF: Buzzer off
CONT: Continuous tone
INT: Intermittent tone f) Bearing pulse/rot.(IN) Change the setting when connected to the other type of radar g) Bearing pulse/rot.(OUT) Change the setting when connected to the other type of radar h) Built-in simulator To display stored radar picture for presentaion purposes. i) Interference Rejection Reject the interference from other radar transmissions
OFF: IR OFF
IR1: ON level 1
IR2: ON level 2
72
HOLD
EBLs and VRMs can be used
j) Ship's Speed Own ship's speed setting
NMEA: The speed data fed from an external speed sencor
in NMEA sentence form.
MANU: MANUAL speed input set by an operator using
the rotary control.
LOG: The speed is calculated by log pulse. Set the pulse
rate with the rotary control.
k) On-screen Language To select the language used for MENU and SOFT KEY ( Note2: )
l) Scan Speed Scanning speed setting STD: Standard HIGH: High speed
( The setting can be changed in stand-by mode only. )
m) Color Video presentation switch MONO: Yellow or Green monochrome MULTI: Red to Green multi-color
Note 1: HOLD function
POWER = POWER key to press
The HOLD function is only available in standby mode that momentarily freezes the radar picture. In this mode, you can use VRMs and EBLs and, as far as the operation continues the picture stays frozen. If you leave these controls, the timer starts to count and after 30 seconds the screen will be put back automatically to normal transmitting mode.
Setting HOLD POWER (Operation)
| | |
(Under Tx)^<-------Under HOLD mode--->^<-----------ST’BY DISPLAY-------------------------------­ Turn to transmission off
EBL,VRM operation:X seconds X + 30seconds (Time used) NOTE) EBL and VRM function is usable in HOLD state.
“HOLD” is displayed and blinks.
Setting HOLD
Tx OFF
X + 30sec.
ST’BY
Note 2: 15 languages
to locate a target.
CHI : Chinese KOR : Korean DAN : Danish NOR : Norwegian ENG : English POR : Portuguese FRE : French RUS : Russian GER : German SPA : Spanish GRE : Greek SWE : Swedish ITA : Italian TUR : Turkish JPN : Japanese
73
(TX delay too short)
5.5.4.5.4 Changing the content of priority for NMEA input(NMEA PRESET)
(1) (1) When NMEA PRESET is selected from CUSTOM items and the "ENT" key is pressed, the NMEA
PRESET screen (See chart below) appears. (2) (2) Select items with up-down cursor keys and contents of NMEA formatter with left-right cursor keys. (3) (3) Change the priority of NMEA formatter with encoder knob. (4) (4) The formatter in the left position has a higher priority than that of the right position.
Repeat this operation when multiple settings are necessary.
a)Lat/Lon b) Heading c) Ship's speed d) Way point e)Depth of water f) Cross track error
NMEA PRESET
L/L GGA>GLL>RMA>RMC HEAD HDT>HDG>HDM>HSC>VHW>VTG SPEED VHW>VTG>RMA>RMC WAY POINT BEC>BWC>BWR>BER>BPI>RMB DEPTH DBT>DPT XTE RMB>XTE
SET WITH CONTROL KNOB
PRESS ENTER KEY TO RETURN
(5) After the setting is completed, exit from the NMEA PRESET screen with the "ENT" key. To suspend
the changes press the ENT key. All newly set items will be cancelled.
5.5.4.5.5 Changing the content of settings (ADJUST)
The items in the ADJUST menu are used for setting up the equipment at installation, retrofitting, etc.
where various functional parameters need to be set up or reset. Once set up, resetting may be not necessary.
(1) Adjusting distance (TX TIME DELAY ADJ)
This adjustment is necessary to set up the distance to targets to within the specified accuracy. Before proceeding to adjustment, set respective controls as follows: (5) First, set the range scale to 0.25 NM, FTC to minimum, and GAIN to optimum level. Then adjust STC to
minimize the center spot ( a split of transmission energy shown like a sun) to a single dot.
(2) Adjusting the distance.
(2)-1 Select ADJUST by "common operations for CUSTOM". Use the up or down cursor key to select
TIMING ADJ from the pull-down menu and press the "ENT" key. (2)-2 Find a straight linear target such as a jetty, bridge, etc. (2)-3 Turn the rotary control either CW or CCW to obtain a linear echo shown like the one in Figure
b). (2)-4 Press the "ENT" key to exit from this menu.
Up/Down ENT Control knob ENT
To select TIMIG ADJ Do Timing adjustment Fix TX Timing Delay
a) Pushing echo (TX delay too much)
b) Properly set
c) Pulling echo
74
Adjust with Control knob
(2) Adjusting angle (HEAD ADJ)
The purpose of this adjustment is to exactly orient the Heading Mark on the screen with the ship’s bow
direction.
Note: Heading offset value for open antenna is different from that of a radome antenna.
(1) In preparation for adjusting the angle, the following adjustments are to be conducted.
(1)-1 Find one small target within a 0.5 to 1.5 NM range which, lying in the bow direction, can be visually
observed and is clearly recognized on the radar screen. (1)-2 Measure the bearing of this target from the bow direction using a compass. Let it be θc. (1)-3 Measure the bearing of the above target in head up (HU) mode using EBL. Let it be θr. (1)-4 Calculate the following:
θ
c - θr : if θc is greater than θr 360 - ( θr - θc ) : if θr is greater than θc The obtained value is the azimuth error of your radar at installation. If θc and θr are equal, the ad­justment described below is unnecessary.
(2) Adjustment procedure
(2)-1 Select ADJUST by "common operations for CUSTOM" and select HEAD ADJ from among the
pull-down menu using the up or down cursor key. Press the "ENT" key to fix the HEAD ADJ
item. (2)-2 Rotate the rotary control to set the value calculated. (2)-3 When the adjustment is finished, press the "ENT" key to exit from this menu.
Up/Down ENT Control knob ENT
Select HEAD ADJ. Set a value to .
3
1 HU
HEAD DIRECTION ADJUSTMENT
ADJUST WITH CONTROL KNOB
PRESS ENTER KEY TO RETURN
_358.8°_
HEADING Adjustment
(3) Adjusting receiver tuning (TUNING CAL)
Normally you do not need to make this adjustment. This adjustment may be necessary to ensure normal
automatic tuning operation. However, if the echo sensitivity is poor or there is any symptom suggesting improper tuning, you may need to re-adjust the tuning by the following procedures.
(1) Choose several stable video images in the 3 NM range or more. (2) Select ADJUST by "common operations for CUSTOM", and select TUNING CAL using the up or
down cursor key from the pull-down menu. Press the "ENT" key to fix the selection.
(3) The tuning adjustment screen (TUNING CALIBRATION) will appear, and then select AUTO with
up-down cursor key.
75
TUNING CALIBRATION
Adjust with Control knob
(4) Rotate the rotary control either CW or CCW to obtain the largest echo presentation on the screen. (5) Select MANUAL with the down cursor key. (6) Rotate the rotary control again to obtain the largest echo presentation. (7) When the adjustment is finished, press the "ENT" key to exit from the TUNING CALIBRATION screen.
Operate of (3) to (7)
Up/Down Control knob Up/Down Control knob ENT
Select AUTO Adjust tuning Select MANU Adjust tuning
3
1 HU
Echo remain.
Adjust with control knob
Select with up-down cursor key
READ OPERATION MANUAL SELECT ITEM WITH KEY TUNE WITH CONTROL KNOB PRESS ENTER KEY TO MEMORY
AUTO 31
MANUAL 36
(4) Adjusting the antenna height (ANTENNA)
Depending on the position at which the antenna is installed, the STC level may need to changed. Use the following procedures to set up. To obtain the best result, we suggest consulting your local SIMRAD dealer for proper setting.
(1) Select ADJUST by "common operations for CUSTOM", and then select ANTENNA from the pull-down
menu using up or down cursor key. Press the "ENT" key to fix the selection. (2) The adjustment screen will be shown. Set an appropriate value using the rotary control to choose the
value from 1 to 9. (3) Press the "ENT" key to exit from this menu.
Up/Down ENT Control knob ENT
Select ANTENNA Choose value Complete
3
1 HU
STC CURVE ADJUSTMENT
ADJUST WITH CONTROL KNOB
PRESS ENTER KEY TO MEMORY
STC CURVE _5_
ANTENNA Adjustment
76
(5) Setting the receiver GAIN (GAIN)
Using this function, you can set up the automatic and manual gain level. As widely accepted conven-
tion, the receiver gain should be set to the level that the noise speckles is slightly shown on the screen.
There are two modes of setting for AUTO and MANUAL, to each mode you can independently set the
GAIN level. Use the following procedure to set up.
In MANUAL mode, you can preset the MANUAL GAIN to current MANUAL gain level as standard. When you enter "G60" as gain level, for instance, "G60" will be preset as standard MANUAL level. (1) Select ADJUST by "common operations for CUSTOM" and select GAIN from the pull-down menu
items. Press the "ENT" key to fix the selection. (6) Turn the rotary control to set the desired level from 1 to 30. (7) Press the "ENT" key to fix the setting.
Up/Down ENT Control knob ENT
Select GAIN Choose value Complete
(6) Setting the STC level (STC)
Using this function, you can set up the STC level to your needs. Proper STC setting should be such that small targets such as buoy and small craft are clearly shown while slight sea clutter appears on the screen. In AUTO mode, you can preset the AUTO STC level and AUTO FTC level as well. When entered at HARBOR (HBR) mode, you can preset the HARBOR STC level. In MANUAL mode, you can preset the best suited STC level as standard MANUAL STC level. (1) Select ADJUST by "common operations for CUSTOM", and select STC from the pull-down menu. Press
the "ENT" key to fix the selection. (2) The set up screen will be displayed. Rotate the rotary control to obtain an appropriate STC level on the
screen. The STC digital value will change from 1 to 16. (3) Press the "ENT" key to exit from the adjustment screen.
Up/Down ENT Control knob ENT
Select STC Choose value Complete
5.5.4.5.6 ATA preset (ATA PRESET)
Before using the ATA function, the settings described below are necessary. Note: Use the ATA function in either the PPI or ALL PPI mode. Even if other modes are used, the ATA still continues tracking though the symbols and data are not displayed on the radar.
Select the ATA PRESET items from the SET UP/CUSTOM menu. The menu contents are as follows. (1) When ATA PRESET is selected from CUSTOM items and the "ENT" key is pressed, the ATA PRESET
screen (See chart below) appears. (2) Select items with up-down cursor keys and change the value of each item with encoder knob. (3) Change the item of VECT(vector) MODE with right-left cursor keys. (4) Change the item of ATA with right-left cursor keys.
-------------------------------------------------------­ CPA SET 0.0 NM TCPA SET 0 MIN VECT SET 6 MIN VECT MODE REL TRUE ATA ON OFF
-------------------------------------------------------­Check that ON in the ATA items is highlighted. If OFF is highlighted (selected), the ATA does not function. * Unless the ATA board is installed properly, the ATA PRESET items are not displayed on the above SET UP/CUSTOM menu.
77
5.6 ATA Operation
5.6.1 ATA Board Specifications (1) Acquisition Manual A target is acquired manually by a cross cursor driven by the Pointing Device. (2) Tracking Automatic (3) Number of tracked targets 10 targets maximum (4) ATA data output Target Number, distance, bearing, speed, course, CPA and TCPA (5) Alarm Collision alarm, activated when a target enters the preset CPA and TCPA ranges. Lost alarm, activated when a target can no longer be tracked. (6) Display Symbols: Predicted point and target number Vector : Predicted motion of a target as a result of own ship's direction and speed input. Display modes: Relative (REL)/True (TRUE) (7) Tracking range 0.5 to 40 NM (8) PRF 2,000 Hz maximum (9) Bearing signal 1,080 or 2,048 pulses / rev (Switched automatically) See Note.
Note: The ATA board does not accept bearing signals other than specified above. In case the ATA board is used in the monitor mode display, make sure an incoming bearing pulse rate agrees with that specified in this specification.
5.6.2 Operating Instructions
5.6.2.1 Outline
The ATA detects a target from radar image signals and measures the distance from the target and its bearing automatically. By calculating changes in the measurement results to predict the target movement, the ATA tracks the target automatically. The ATA calculates the CPA (closest point of approach) and the TCPA (time required for the ship to reach the CPA) from the movement of the target toward the ship. Then comparing them to those preset, it generates a collision alarm if both values are smaller than the preset ones. The target bearings are calculated by (1) bearing of the target toward the ship and (2) bearing of the ship's heading marker. Therefore, the accuracy of the data on the heading marker's bearing affects tracking per­formance. Tracking may become impossible if the compass is inaccurate and especially when the ship is yawing or changing the course. These cases, however, are not caused by a malfunction of ATA.
5.6.2.2 Setting
Before using the ATA function, the settings described below are necessary. Note: Use the ATA function in either the PPI or ALL PPI mode. Even if other modes are used, the ATA still continues tracking though the symbols and data are not displayed on the radar. (1) Switching the ATA function ON/OFF Select the ATA PRESET items from the SET UP/CUSTOM menu. The menu contents are as follows.
------------------------------------------------------­CPA SET 0.0 NM TCPA SET 0 MIN VECT SET 6 MIN VECT MODE REL TRUE ATA ON OFF
------------------------------------------------------­Check that ON in the ATA items is highlighted. If OFF is highlighted (selected), the ATA does not function. * Unless the ATA board is installed properly, the ATA PRESET items are not displayed on the above SET UP/CUSTOM menu.
78
5.6.2.3 Operation
(1) Acquisition of a target Firstly, select the target to track. Place the cursor on the target image and acquire it by using the ACQ (ac­quisition) function. Press the ACQ key. When operating from the MENU, place the cursor on NAVI/ACQ and press the ENT key. Select the target when it is displayed clearly and no other targets are displayed around it. If other targets are displayed around it, the ATA may track a different one. All targets acquired by ATA are identified by the numbers, from 0 to 9. These figures will be shown in the upper right window on the screen. A vacant column shown like "-" indicates no target being acquired. Before starting selection, use the TGT NUM (target number) function so that "-" is highlighted. The TGT NUM function is used to change the target numbers. The target number will not change auto­matically unless this function is used. Press the TGT NUM key. When operating from the MENU, place the cursor on NAV/TGT NUM and press the ENT key. When ATA starts acquisition, a symbol appears at the cursor position on the screen, and the target number is shown on the lower right side of the symbol.
(2) Tracking the target When the operator acquired the target by the procedure (1), ATA automatically detects the target to start automatic tracking. As soon as stable tracking is established, a vector will be developed on the screen. The target tracking is not relevant to the range scale in use, i.e. the tracking continues even if the range scale is changed beyond the viewable ranges for the target. Note: A tracked small target may be lost when the range scale is changed to shorter pulse ranges, causing the target signal level to be decreased. This may lead to a tracking failure on the target that will become a lost target.
(3) Canceling target tracking To cancel tracking, use the DEL (delete) function. The number highlighted on the upper right of the screen will disappear. If ALL DEL (delete all) is selected, the ATA will cancel tracking of all targets. Press the soft key if the DEL function has been set. When operating from the MENU, place the cursor on NAVI/DEL or NAVI/ALL DEL and press the ENT key. When the radar is set to the SY'BY mode, the ATA will cancel tracking of all targets.
(4) Data display When necessary, numerical data of the current tracking target can be displayed in the data display window. Use the DATA function to display the numerical data of the number highlighted on the upper right corner of the screen. Press the soft key if the DATA function has been set. When operating from the MENU, place the cursor on NAVI/DATA and press the ENT key.
Items to be displayed are as follows. Target number: TGT NO.x The number of the target currently displayed. Vector time: TIME xx MIN. Setting time to display vector length. (Speed x Time=vector length) Vector mode: TRUE or REL Display mode of vector and data. TRUE and REL represent true and relative speeds, respectively. Target data: BRG (bearing), DIST (distance), CRS (course), SPD (speed), CPA (closest point of approach) and TCPA (time required for the ship to reach the CPA) State: A collision or lost alarm will appear according to the state of the target. Example:
-----------------------------------------------------------------------------------------------------------­| TGT No.x ALM LOST TIME xxMIN TRUE |
-----------------------------------------------------------------------------------------------------------­| BRG 123.4DEG CRS 234.5DEG CPA 12.3NM | | DIST 12.3NM SPD 10.0KT TCPA 12.3MIN |
-------------------------------------------------------------------------------------------------------------
79
(5) ATA indications In the PPI and ALL PPI modes, symbols and data are displayed. In other modes, target tracking is still continued though the ATA display and operation are disabled. The symbols are as follows:
Acquired target
(6) Ship's speed setting The ship's speed can be set in the SPD SET item in the SET UP/CUSTOM/PRESET2 menu. Other than the standard NMEA interface, manual setting and log pulse input can also be selected. In the case of manual setting, input the ship's actual speed. Menu indication is as follows:
---------------------------------------------------------------------------------------­SPD SET NMEA MANU 0.0 KT LOG 200P
----------------------------------------------------------------------------------------
5.6.2.4 Interface
(1) Data output The ATA data output is ready at the optional connector terminal on the rear of the display unit. Pin No.32 is the NMEA_OUT signal terminal which outputs signals conforming to the NMEA0183. This output terminal is used for the TARGET function (to output L/L of the cursor position), the MOB function (to output L/L of the ship's position) and the ATA data output function. The data format is as follows: $RATTM,01,0.42,292.1,T,4.99,0.0,T,0.4,0.0,N,,T,,,M*2A
Description
$RA Unit identification code (radar) TTM Formatter 01 Target number
0.42 Distance to the target
292.1 Bearing of the target (°) T Indicates the true bearing.
4.99 Speed (knots)
0.0 Course (°) T Indicates the true speed and course, while R indicates relative movement.
0.4 Indicates the CPA (closest point of approach)
0.0 Time required for the ship to reach the CPA (min.) N Indicates the unit of distance used: NM T Indicates tracking condition: Q: unstable, T: tracking, L: lost M Indicates that acquisition is carried out manually. *2A Sum checking
(2) Log signal input The log signal can be used for ship speed input by inputting it to the optional connector terminal on the rear of the display unit. Pin No.32 is the log signal terminal and it is driven between itself and pin No.14 (GND) using contact signals such as a relay. 400, 200, 150 or 100 pulses/NM signal can be selected.
Tracked target Target with data
display
Lost target Dangerous target under
automatic tracking
80
Loading...