Koden CVS-128, CVS-128B Operation Manual

Download

Page 1

Page 2

Declaration of Conformity

(As referred to in Annex IV 2. of Directive 2004/108/EC)

Declares under his sole responsibility that the produced Echo Sounder manufactured by

Koden Electronics Co., Ltd.

5278 Uenohara

Uenohara-Shi

Yamanashi-Ken

409-0112, Japan

Telephone +81 554 20 5860 Telefax +81 554 20 5875

Identified by the type number relevant essential requirements of Directive 2004/108/EC and is in conformity with the EMC

requirements of EU harmonised standard

CVS-128

to which this declaration refers conforms to the

EN 60945: 2002 (Clauses 9, 10 & 12)

Authorised representative in Europe

Heinz Hoghoff Koden Elektronik GmbH. Am Gewerbepark 15 D-64823, Gross–Umstadt Germany. Phone +49 6078 2056 Telefax+49 6078 73824

Signed Heinz Hoghoff,

Dated 15 April 2009

N.B. As this product is for Maritime use compliance with Directive 72/23/EEC is not required.

Page 3

Declaration of Conformity

(As referred to in Annex IV 2. of Directive 2004/108/EC)

Declares under his sole responsibility that the produced Echo Sounder manufactured by

Koden Electronics Co., Ltd.

5278 Uenohara

Uenohara-Shi

Yamanashi-Ken

409-0112, Japan

Telephone +81 554 20 5860 Telefax +81 554 20 5875

Identified by the type number CVS-128B to which this declaration refers conforms to the

relevant essential requirements of Directive 2004/108/EC and is in conformity with the EMC requirements of EU harmonised standard

EN 60945: 2002 ( Clauses 9,10 & 12 )

Authorised representative in Europe

Heinz Hoghoff Koden Elektronik GmbH. Am Gewerbepark 15 D-64823, Gross–Umstadt Germany. Phone +49 6078 2056 Telefax+49 6078 73824

Signed : Heinz Hoghoff,

Dated : 01 Jun. 2012 Document No. 72-2731U-X003

N.B. As this product is for Maritime use compliance with Directive 72/23/EEC is not required.

Page 4

CVS-128/128B Revision History

CVS-128/128B Operation Manual

Doc No. 0093112802

Document Revision History

No. Doc. No-Rev. No. Reviced Date

(Y/M/D) 0 0093112802-00 2009/05/27 First edition 1 0093112802-01 2009/07/09 Chapter 1 2 0093112802-02 2010/01/12 Revision (From software KM-E79* Ver01.03 to Ver01.**)

Revision (From software KM-E79 Ver01.06 to Ver01.**)

3 0093112802-03 2011/04/27

4 0093112802-04 2011/12/26 Important Notice, Chapter 2, Chapter 6 5 0093112802-05 2012/06/15

6 0093112802-06 2013/06/24

System Configuration, Configuration of Equipment, Chapter 5, Wording

Added CVS-128B Revision (From software KM-E79 Ver01.08 to Ver01.**) Revision (From software KM-F22* Ver01.02 to Ver01.**) System Configuration, Configuration of Equipment, Chapter 5

Revised Content

8 9

*KM-E79: CVS-128, KM-F22: CVS-128B **Subject to version change

Document No. Revised Version Norm

When part of the document needs to be revised, the document has advanced revision number. The document No. is indicated at the lower right side on the cover and at the left or right side of the footer region of each page.

© 2009-2013 Koden Electronics Co., Ltd. All rights reserved. No part of this publication may be reproduced, transmitted, translated in any from by any means without the written permission of Koden Electronics Co., Ltd. The technical descriptions contained in this publication are subject to change without notice. Koden assumes no responsibility for any errors, incidentals or consequential damages caused by misinterpretation of the descriptions contained in this publication.

0093112802-06 i

Page 5

Important Notice CVS-128/128B

Important Notice

 For copy and transcription of this Operation Manual (hereinafter referred to as this manual),

permission from Koden is needed. Koden prohibits the un-authorized copy and transcription of this manual.

 If this manual is lost or damaged, consult a dealer of Koden or Koden.  The specification of the products and the contents in this manual are subject to change without

notice.

 The contents displayed on the menu of product may be different from the expression of this

manual. The fonts and shapes of the keys and menus in the illustration may differ from the actual ones, and some parts may be omitted.

 Koden is not liable for damages and troubles arisen from misunderstanding of the contents in this

manual.

 Koden is not liable for any damages caused by earthquake, lightning, wind and flood damage and

fire for which Koden is not responsible, and actions by third parties, other accidents, customer’s unintended error/abuse and the use under other abnormal conditions.

 Koden is not liable for damages of accompaniment (change/loss of memorized content, loss of

business profit, stop of business) arisen from use or failure of our products.

 If the stored data are changed or lost, irrespective of causes of troubles and damages, Koden is

not liable for them.

 Koden is not liable for any damages arisen from malfunction caused by combination of software

and connected equipment in which Koden is not engaged

ii 0093112802-06

Page 6

CVS-128/128B For Your Safe Operation

For Your Safe Operation

Pictorial used in this Operation Manual

This Operation Manual uses the following pictorials. Understand the meaning of each pictorial and implement the maintenance and inspection.

Symbol Meaning

Mark for warning

This symbol denotes that there is a risk of death or serious injury when not dealing with it correctly.

Mark for danger high voltage

This symbol denotes that there is a risk of death or serious injury caused by electric shock when not dealing with it correctly.

Mark for caution

This symbol denotes that there is a risk of slight injury or damage of device when not dealing with it correctly.

Mark for prohibition

This symbol denotes prohibition of the specified conduct. Description of the prohibition is displayed near the mark.

Caution Item on Equipment

Be careful of a high voltage inside.

A high voltage, which may risk your life, is used. This high voltage remains in the circuit after you have powered off switch. To prevent touching the high voltage circuit inadvertently, the hard cover is provided to the high voltage circuit and the high voltage caution label is affixed. Ensure to power off switch for your safety and discharge the electricity remaining in the capacity before starting to check. An engineer authorized by our company should inspect and maintain

Be sure to power off in the boat.

If the power switch is inadvertently powered on during work, you will be electrified. To prevent such accident from occurring, ensure to power off in the boat and the power of equipment. Furthermore, it is safer to hang the caution tag described as [Under Work] near the power switch of equipment.

Be careful of dust

Inhaling dust may cause A respiratory disease. When cleaning the inside of equipment, be careful not to inhale dust. Wearing a safety mask is recommended.

0093112802-06 iii

Page 7

For Your Safe Operation CVS-128/128B

Caution on location of equipment

Do not install the equipment where it is excessively damp and suffers from excessive water drops.

Escaping from static electricity

The static electricity may be generated from the carpet on the floor in the cabin or clothes made of synthetic fiber . The static electricity may destroy the electronic parts on the circuit board. Handle the circuit board, taking the measure of static electricity free.

Install the transducer at the location where it is not affected by bubble and noise The bubble and noise seriously degrade the performance of this unit.

Caution Item on Handling

Do not disassemble or modify. It may leads to trouble, fire, smoking or electric shock. In case of trouble, contact our dealer or our company.

In case of smoke or fire, boat power off and the power of this unit. It may cause fire, electric shock or damage.

Be cautious of remaining high voltage. A high voltage may remain in the capacitor for several minutes after you have powered off. Before inspecting inside, wait at least 5 minutes after powering off or discharge the remaining electri city in an appropriate manne r . Then, start the work.

The information displayed in this unit is not provided directly for your navigation. For your navigation, be sure to see the specified material.

Use the specified fuse. If un-specified fuse is used, it may cause a fire, smoke or damage.

Whenever transmitting, be sure to submerge the transducer in water first. If transmitted without submerging the transducer, it may be dama ged.

iv 0093112802-06

Page 8

CVS-128/128B Contents

Contents

Document Revision History ....................... i

Important Notice ....................................... ii

For Your Safe Operation ......................... iii

Contents ................................................... v

Introduction ................................................ ix

System Configuration ................................. x

Configuration of Equipment ....................... xi

Change the frequency ............................. xiv

Chapter 1 Basic Operation ...................... 1-1

1.1 How to use the key .................... 1-1

How to remove the hard cover ... 1-2 When removing the

CVS-128/128B Display unit ....... 1-2

The clean of CVS-128/128B

Display unit ................................ 1-2

1.2 Power On/Off ............................. 1-3

Power on .................................... 1-3

Power off .................................... 1-3

Alarm of Power Voltage ............. 1-3

1.3 LCD Brilliance Adjustment ......... 1-4

Adjustment of LCD Brilliance ..... 1-4

Brightness Adjustment of Panel

Brilliance .................................... 1-4

1.4 Switch-over of Display mode ..... 1-4

Normal Image (Low frequency,

High frequency) .......................... 1-4

Dual frequency ........................... 1-5

Zoom (Low frequency, High

frequency) .................................. 1-5

Navigation Menu (NAV1, NAV2) 1-7

1.5 Selection of NAV Display ........... 1-8

Type of NAV Display .................. 1-8

Selection of NAV Menu .............. 1-8

1.6 Switch-over of Range ................ 1-9

Setting the range switching to auto

range .......................................... 1-9

Setting the range switching to

Manual range ............................. 1-9

1.7 Setting of Shift ............................ 1-9

Setting of Manual Shift ............... 1-9

Release of manual Shift ........... 1-10

Setting of Auto Shif t ................. 1-10

1.8 Gain Adjustment ....................... 1-10

Basic Operation of Gain ........... 1-11

Selecting the auto gain ............ 1-11

Adjusting the gain by auto ....... 1-11

Selecting the manual gain ....... 1-11

Manual adjustment of the gain . 1-11

1.9 Use of [EVENT] key ................. 1-12

Selecting the event key function1-12

Presetting the waypoint ........... 1-12

Store the image ........................ 1-13

Fishing hot spot ........................ 1-13

1.10 Use of [F1] / [F2] key ................ 1-14

Selecting the

[F1] / [F2] key ......................... 1-14

Preset of [F1] / [F2] key ........... 1-14

1.11 Operation of VRM .................... 1-15

1.12 Display of fish information ........ 1-15

Display the fish symbol /Stop the

display of fish symbol ............... 1-16

Selecting the symbol info ......... 1-16

Fish symbol detection

adjustment ............................... 1-16

Size adjustment ....................... 1-16

Big fish / Big fish color ............. 1-17

Points to note in use of fish

symbol ...................................... 1-17

Chapter 2 How to use the Menu ............. 2-1

2.1 How to operate the menu .......... 2-1

0093112802-06 v

Page 9

Contents CVS-128/128B

Display the menu / Stop the

display of menu .......................... 2-1

Menu Operation ......................... 2-1

2.2 Changing of Image Speed.......... 2-2

2.3 Rejection of Interference ............ 2-2

Interference Rejection ................ 2-2

2.4 Color Rejection of Weak Echo ... 2-3

Color Rejection ........................... 2-3

2.5 Rejection of Noise ...................... 2-3

Noise Rejection .......................... 2-3

2.6 Setting of Shift step .................... 2-3

2.7 Selection of Zoom ...................... 2-3

2.8 Setting of Zoom Range .............. 2-4

2.9 Setting of Zoom Start ................. 2-4

2.10 Preset of Range ......................... 2-4

Easy registration method of

the range .................................... 2-5

Switch-over of Sona-Tone Connection of External

Speaker .................................... 2-12

2.17 Explanation of Menu Item ........ 2-12

Inner-hull .................................. 2-12

TVG .......................................... 2-13

Change the TX power .............. 2-13

Change the Pulse width ........... 2-13

Change the Bandwidth ............. 2-14

D. Range .................................. 2-14

Display Width ........................... 2-14

Display the A scope / Stop the

display of A scope .................... 2-14

Change the display color of echo

sounder image ......................... 2-14

Change the depth value ........... 2-15

Display the depth unit / Stop the

..... 2-12

2.11 Setting of Background Color ...... 2-5

2.12 Setting of White Line .................. 2-5

2.13 Setting of Alarm .......................... 2-6

Stopping the alarm sound .......... 2-6

Setting the alarm ........................ 2-7

Release the alarm ...................... 2-7

Confirm the alarm state .............. 2-7

2.14 Preset/ WPT edit/ WPT delete of

Waypoint .................................... 2-8

NAV Start .................................... 2-8

Cancel the NAV .......................... 2-8

Edit the destination ..................... 2-8

Delete the waypoint .................... 2-9

Recall the stored image and

preset it as a destination ............ 2-9

2.15 Store/Recall/ Deletion of Image 2-10

Store the image ........................ 2-10

display of depth unit ................. 2-15

Display the water temp graph / Stop the display of water temp

graph ........................................ 2-15

Setting of the background color of

NAV display .............................. 2-15

Setting of the echo sounder

display at NAV display .............. 2-15

Image Swap ............................. 2-15

Display the Operation guide / Stop the display of Operation

guide ......................................... 2-15

Display the detection area / Stop the display of detection

area .......................................... 2-16

Setting of Scale display ............ 2-16

Change the scale value ............ 2-16

Recall the stored image ........... 2-10

Delete the stored image ........... 2-11

Add the comment to the stored

image ........................................ 2-1 1

2.16 Explanation of Sonar ................ 2-12

vi 0093112802-06

Change the image direction ..... 2-16

Setting of Depth measurement 2-16

Change the display color.......... 2-16

Setting of Key lock ................... 2-17

Change the scale type ............. 2-17

Page 10

CVS-128/128B Contents

Change the bottom color ......... 2-17

Change the image partition ...... 2-17

Display the frequency / Stop the

display of frequency ................. 2-17

Selecting a display area of fish

symbol indication ..................... 2-17

Chapter 3 How to use the menu2 ............ 3-1

3.1 Display of Menu ......................... 3-1

Display the menu ....................... 3-1

Return to the normal menu ........ 3-1

3.2 Setting of External Input/Output . 3-1

Buzzer Setting ............................ 3-1

Temp Source .............................. 3-1

Speed Source ............................ 3-1

Baud Rate .................................. 3-1

NMEA Monitor ............................ 3-2

NMEA Output Data .................... 3-2

All WPTs deletes ........................ 3-4

All stored image deletes ............ 3-4

Bottom start ................................ 3-4

Past image ................................. 3-4

Inner-hull .................................... 3-4

TD select .................................... 3-4

3.6 Setting of Adjust2 Item ............... 3-4

STC strength adjust Low / High . 3-4

STC depth adjust Low / High ..... 3-4

Color adjust ................................ 3-5

Image speed adjust.................... 3-5

Bottom limit ................................ 3-5

Sounding .................................... 3-5

3.7 Frequency select ........................ 3-5

Frequency select (Low / High) ... 3-5

Power frequency adjustment ..... 3-5

Chapter 4 Maintenance and Inspection .. 4-1

3.3 Setting of Correction Item .......... 3-2

Draft Set ..................................... 3-2

Sonic Speed ............................... 3-2

Water Temp ................................ 3-2

Boat Speed ................................ 3-2

Directivity angle (Low/High) ....... 3-2

Bubble ........................................ 3-3

Bubble time set .......................... 3-3

3.4 Setting of Basic Set Item ........... 3-3

Language ................................... 3-3

Range & Speed Unit .................. 3-3

Depth Unit .................................. 3-3

Temperature Unit ....................... 3-3

Local time Offset ........................ 3-3

GPS select ................................. 3-3

GPS initialize .............................. 3-3

3.5 Maintenance Menu .................... 3-3

Simulation .................................. 3-3

Slide show .................................. 3-4

Initialize ...................................... 3-4

System Check ............................ 3-4

4.1 Inspection ................................... 4-1

4.2 Cleaning ..................................... 4-1

CVS-128/128B Display unit ....... 4-1

Transducer ................................. 4-1

4.3 Fuse Replacement ..................... 4-2

4.4 If you suspect a trouble .............. 4-2

4.5 Diagnostic Test ........................... 4-3

Diagnose .................................... 4-3

Confirm the version .................... 4-3

Return to the menu .................... 4-3

Chapter 5 Installation .............................. 5-1

5.1 Items of Caution on Installation . 5-1

Unpacking the components ....... 5-1

Inspection of components and

accessories ................................ 5-1

Decision of Installing Location ... 5-1 Laying and Connection of Cable 5-2

Confirmation after Installation .... 5-2

5.2 Installation of CVS-128/128B

Display unit ................................ 5-3

Desk-top Installation .................. 5-3

0093112802-06 vii

Page 11

Contents CVS-128/128B

Flush-mount Installation ............. 5-5

5.3 Installation of Transducer ........... 5-6

In case of Inner-hull .................... 5-6

In case of Through hull ............... 5-7

5.4 Wiring ......................................... 5-8

Connection of Cable to

CVS-128/128B Display unit........ 5-8

Pin Assignment of Rear

Connector ................................... 5-8

Connection of Power Cable ....... 5-9

Connection of Transducer ........ 5-10

Connection with external

equipment................................. 5-1 1

Connection with GPS-20A ....... 5-11

Connection with Speed Senso r or Water Temperature Sensor

(Option) .................................... 5-12

Connection of External Speaker

for Sona-Tone

(Prepared by a customer) ........ 5-13

Connection of External Monitor (J7) (Prepared by a customer) . 5-13

5.5 Serial Data ................................ 5-14

Input Data ................................. 5-14

Output Data .............................. 5-14

Chapter 6 Table Attached ........................ 6-1

6.1 Menu List .................................... 6-1

6.2 Specification ............................... 6-5

6.3 Appearance ................................ 6-7

viii 0093112802-06

Page 12

CVS-128/128B Introduction

Introduction

The CVS-128/128B is a Dual frequency Color LCD display echo sounder. This unit equipped with digital process displays the circum stance in the water under all conditions,

matching with the high luminance 8.4 inch LCD. The main features of this unit are as follows:  With the digital reception process, the compatibility of the high resolution in a shallow depth and the

noise rejection capability in a deep depth are established. The auto mode function provides the best image.

 The high-performance LCD maint ains high visibility under any conditions.  The unit can be installed in an open b rid ge and is highly waterproof.  Sona-Tone (Sonar sound) functio n is equipped with for catching situations schools of fish and

others by sound.

 Up to 10 images can be stored. If you connect the optional GPS, the fishing hot spot function, that

directs your boat to navigate easily to the location desired, is available by marking the event mark when recalling the stored image.

 With the adoption of a specific filter (AR coat), an image can be seen clearly, refusing sunshine.

The countermeasures against the reflection on the LCD screen and dew are provided.

 The various alarm functions are available. (Bottom, scho ol of fish, water tempe rature*, boat speed*,

arrival*, XTE*, power) (Note: The mark * denotes that the connection of option is mandatory)

 When flush-mounting, the unit can be easily installed from front side.  The RGB output for an external monitor is provided a s standa rd eq uipment. The use of the external

monitor enables you to observe easily the echo sounder scree n at a location which is remote f rom a main unit. (External monitor: Prepared by a customer)

 CVS-128B is the high sensitivity model with broadband transducer. This model can be used at your

optimum frequencies within the specification of the broadband transducer. You can set 2 frequencies depending on a target fish or intended purpose du ring operation.

0093112802-06 ix

Page 13

System Configuration CVS-128/128B

System Configuration

Connection Diagram

To Transducer connector

(J6 connector)

CVS-128/128B Display unit

With mounting bracket and hard cove

To POWER connector

To External monitor connector

CW-264A-2M

CW-840-0.3M

(J7 connector)

CW-576-0.5M

External power output (For GPS etc)

External speaker (For speaker with amplifier)

NMEA circuit input output External navigation equipment, external water temperature mete

Red

Black

Legend

Standard configuration Option

Owner supply

(Owner supply)

10.8 to 31.2VDC

External monitor

(Owner supply)

Connection to the Transduce

Connection to the speed sensor Connection to the wate

Temperature

Note: To use the water temperature sensor / speed sensor,

The wiring of transducer connector has to be changed.

Water temperature senso

speed senso

ST-80/90/100

CVS-128

Transducer P66 (Dual frequency combination type 50 / 200 kHz) Plastic made. Equipped with Transom. (Owner suppl

CVS-128 Transducer TD-501C (Dual frequency combination type 50 / 200 kHz)

Rubber mold made. Equipped with Inner-hull/Ship’s bottom/Ship’s side. Transducer TD-500T-3B / 501T-3B (Dual frequency combination type 50 / 200 kHz)

Bronze made. Equipped with Through-hull. Transducer TD-500T-2B (Dual frequency combination type 50 / 200 kHz)

Plastic made. Equipped with Inner-hull.

CVS-128B

Transducer TDM-071 (38 to 75 kHz)

Transducer TDM-091D (42 to 65 kHz) (130 to 210 kHz)

Urethane mold made. Equipped with Ship’s bottom/Ship’s side

x 0093112802-06

Page 14

CVS-128/128B Configuration of Equipment

Configuration of Equipment

Standard Equipment Configuration List

No. Name of item Type Remark

1 Display unit

CVS-128/128B With mounting bracket

and knob

Weight/

Length

3.2 kg 1

Quantity

2 Hard cover

3 DC power cable

(Combined cable)

4 Fuse

5 Cap

E57MB11060 250 g 1

CW-264A-2M With 12 connector at

one end/ un-treated at the other end

F-7161-3A Cylinder (ø 6.4x30)

LTWCAP-DABCFXC1 For transducer cable

Normal fusion type for main power

connector

2 m 1

6 Operation Manual CVS-128.OM.E English 1 7 Quick Reference CVS-128.QR.E English 1 8 Cautionary Note CVS-SER.RM.E English 1

Essential Option

No. Name of item Type Remark

1 Transducer Type of transducer transducer cable (with

connector at one end)

Weight/

Length

Quantity

0093112802-06 xi

Page 15

Configuration of Equipment CVS-128/128B

Type of transducer

No. Specification Frequency Material /

Length of the

cable

TD-500T-2B

CVS-128 50/200 kHz

600 W

Plastic 9m

TD-500T-3B

CVS-128 50/200 kHz

Bronze 9m

600 W

TD-501C

CVS-128 50/200 kHz

1 kW

Rubber mold

10m

Mounting method Beam width

(Right and left x

back and forth)

Inner-hull

50kHz

50°x50° ( -6dB)

200kHz

17°x17° ( -6dB)

Through-hull 50kHz

50°x50° ( -6dB)

200kHz

17°x17° ( -6dB)

Inner-hull/ Ship’s bottom/ Ship’s side (The CW-840-0.3M is needed)

50kHz

58°x20° ( -6dB)

200kHz

17°x 6° ( -6dB)

TD-501T-3B

CVS-128 50/200 kHz

1 kW

Bronze 9m

Through-hull 50kHz

TDM-071

CVS-128B 38 to 75 kHz

Urethane mold

15m

Through-hull Ship’s bottom/ Ship’s side

With water temperature sensor.

TDM-091D

CVS-128B 42 to 65 kHz

130 to210kHz

Caution: For Inner-hull installation, an Inner-hull kit is necessary.

Urethane mold

15m

Through-hull Ship’s bottom/ Ship’s side

With water temperature sensor.

20°x22° ( -6dB)

200kHz

5°x 5° ( -6dB)

38kHz

30°x20° ( -6dB) 75kHz 16°x 10° ( -6dB)

42kHz

35° ( -6dB) 65kHz

22° ( -6dB) 130kHz

14° ( -6dB) 210kHz

8° ( -6dB)

AIRMAR’s Transducer model P66 is also applicable. (Owner supply)

P66

xii 0093112802-06

CVS-128 50/200 kHz

600 W

Plastic 10m

Transom With water

temperature sensor and speed sensor. (The CW-840-0.3M is needed)

50kHz 69°x69° ( -6dB)

200kHz 16°x16° ( -6dB)

Page 16

CVS-128/128B Configuration of Equipment

Option List

No. Name of Item Specification Remark Weight/Length

1 Water temperature

sensor/speed sensor

ST-80 For transom mounting

Plastic made (with cable)

0.3 kg / 9 m

ST-90 For through-hull mounting

Plastic made (with cable)

ST-100 For through-hull mounting

Bronze made (with cable)

2 GPS sensor GPS-20A-10M-B

[KODEN]

3 Inner-hull kit MFB-04 Plastic made for installing the

MFB-04W Plastic made for installing the

4 Cable for transducer CW-840-0.3M Needed when using the

5 Connector for GPS

sensor

6 Cable for external

monitor

LTWBD-06PMMP-LC Needed when using the

CW-576-0.5M Junction cable for connection of

For GPS measuring (With power & signal cable)

transducer TD-500T -2B

transducer TD-501C

optional water temperature sensor / speed sensor.

GPS-20A (Type B) sensor.

external monitor

0.6 kg / 9 m

1.2 kg / 9 m

0.25 kg / 10 m

1.3 kg

30 cm

0.5 m

0093112802-06 xiii

Page 17

Change the frequency CVS-128/128B

Change the frequency

CVS-128B is used with the other transducer please make sure to set the below items manually in line with the transducer installed.

Caution: The transducer may be damaged if the settings are wrong.

Caution: There are occasions too much noise is generated in a particular frequency to

be connected.

Caution: Fish symbol operation cannot be generated at the other frequencies than the

high frequency of 200 kHz and the low frequency of 50 kHz.

Setting of Output Frequency (CVS-128B)

1 Press the [MENU] key. 2 Select [Freq]  [Freq select (L)]. (See [2.1 How to operate the menu]) 3 Press the [ ] key. 4 Set the output frequency at the low frequency side. (Press the [ ] key or [ ] key) 5 Set the high frequency also in the same way as for the low frequency side, in referen ce to the step

2 to 4.

6 Press the [MENU] key. Then, the edit is finished.

Caution: When single transducer is connected, set the same frequencies for low and

high.

Setting of Power Frequency (CVS-128B)

1 Press the [MENU] key. 2 Select [Freq]  [Power freq adj]. (See [2.1 How to operate the menu]) 3 Press the [ ] key. 4 Set the power supply frequency. (Press the [ ] key or [ ] key)

The recommended power supply frequency for Dual frequency (50 kHz/200 kHz): 107.0 kHz

Transmit

frequency

28 kHz 115.0 kHz 70 kHz 106.5 kHz 38 kHz 105.0 kHz 75 kHz 103.5 kHz 40 kHz 123.0 kHz 120 kHz 109.0 kHz

Recommended

power supply

frequency

Transmit

frequency

Recommended

power supply

frequency

55 kHz 107.0 kHz - -

Caution: There may be much noise on the screen even for the recommended power

supply frequency depending on the transducer. In this case, set the power supply frequency to reduce the noise on the screen.

Caution: Set the power supply frequency to reduce the noise on the screen, when the

other transmission frequency than above is used.

xiv 0093112802-06

Page 18

CVS-128/128B Change the frequency

5 Press the [MENU] key. Then, the edit is finished.

Adjustment of bottom detection

When the bottom can't be detected or when the bottom is of mud pool or seawe ed, [Gain (T D)] shall be turned up. When transfer to fish schools, etc. frequently occurs, [Gain (TD)] shall be turned down.

1 Press the [MENU] key. 2 Select [Adjust]  [Gain(TD)]. (See [2.1 How to operate the menu])

3 Press the [ ] key. The image displays bot tom only. It may show very strong fish targets. 4 Set a value to display the sea bottom continuously without interruption. For high frequency, turn

[GAIN (HF) knob] and for low frequency, turn [GAIN (LF) knob]

After the alteration of setting, please confirm the condition for some time. Those adjustments are recommended to be performed at the site of use.

L: 6.0 H: 6.0 R:M 12.0V

Gain (TD) L

Gain (TD) H

Gain (TD)

Bottom

5 Press the [MENU] key. Then, the edit is finished.

0093112802-06 xv

Page 19

CVS-128/128B Chapter 1 Basic Operation

Chapter 1 Basic Operation

1.1 How to use the key

CVS-128/128B Display unit

1 2

3 4

5 6

Various setting can be done directly. The menu list closes automatically after the key operation of the other keys than [menu].

No. Key Name Explanation

1 [F1] Recalls directly the item preset.

2 [EVENT]

[Cursor]

▲ ▼

4 [MENU] Opens or closes the menu.

5 [F2] Recalls directly the item preset.

6 [▲RANGE▼] Changes the range setting.

[GAIN(HF)

Knob]

[GAIN(LF)

Knob]

Switches to the High frequency or Low frequency of echo sounder

[DISP]

[BRILL

Power

Notifies the external equipment of the present position. Presets the menu. It begins a fishing hot spot.

Selects the menu item. Changes the set value. Moves the VRM marker. Moves the marker for notifying the event.Changes the shift.

Rotate: Changes the gain value. Press: Recalls the gain select.

image, zoom and navigation menu.

Press: Power on. Adjusts the brilliance and brightness of panel. Long-press: Power off.

0093112802-06 1-1

Page 20

Chapter 1 Basic Operation CVS-128/128B

How to remove the hard cover

While widening the claws at right and left sides of hard cover, draw the hard cover towards you.

Claw

When removing CVS-128/128B Display unit

To prevent dust from entering, cap the connector at the rear of CVS-128/128B Display unit and the power cable with caps.

Install the supplied cap to the transducer cable as shown in the figure and cap it.

Caution: Do not pull the cable strongly. If you do so, it will be broken.

The clean of CVS-128/128B Display unit

The cleaning of the display unit goes after removing the front-frame. After removing the front-frame, use a synthetic detergent and OA cleaner and wipe the display unit lightly. Then dry sufficiently, and return the front- frame to original position.

Caution: The display unit has a special coating. Do not use a solvent such as paint thinner,

acetone, alcohol, and benzene, etc.

Caution: Strong rubbing may cause bruising and scratching.

1-2 0093112802-06

Page 21

CVS-128/128B Chapter 1 Basic Operation

1.2 Power On/Off

Power on

1 Press the [BRILL ] key to power on.

The startup menu is displayed. When started up, the internal memories (ROM, RAM) are automatically checked. When checking is normally finished, the menu below is displayed.

Caution: If an error occurs in the memory

check, the LED on the operation panel blinks. The unit may be not function normally. If you suspect trouble, contact the dealer of your purchase or our company.

2 Language Selection at Initial Startup.

When powering on first, the [Language] menu is displayed.

Language

English

日本語

Select the language with [ (The language can be selected by rotating the [GAIN (HF) Knob] or [GAIN (LF) Knob].)

3 When the installation of a transducer is

[Inner-hull], select the [Yes].

Inner-hull

Yes

Press [ the [Yes

]

and [

keys in sequence, and select

]

key or [] key.

]

4 Press the [MENU] key to decide the

language and the inner-hull.

5 After a few seconds, the menu sets the

screen as selected in [DISP].

Caution: In addition to English, Japanese,

there are several compatible languages.

Explanation of the display:

Rainbow pattern

Time mar

Gain

Power supply voltage

larm icon

Range

Function icon

Event icon

L H

Oscillation line

Schools of fish

Fish

Depth

Type of Gain H: High frequency gain L: Low frequency gain

Type of Range R: M: Manual Range R: A: Auto Range R: AS: Auto Shift

Power off

1 When powering off, keep pressing the

[BRILL The remaining time for the power to shut off is displayed on the menu.

] key for 3 seconds.

Alarm of Power Voltage

If detecting the malfunction of the voltage, the

icon blinks and the alarm beeps.

Caution: In case of the low voltage or the

high voltage, it shuts down. The precision of Power Voltage is ± 0.5 V.

0093112802-06 1-3

Page 22

Chapter 1 Basic Operation CVS-128/128B

1.3 LCD Brilliance Adjustment

Adjustment of LCD Brilliance

The brilliance of the display can be adjusted to facilitate visualization.

The [Lcd brill] and [Panel brill] can be switched every time when pressing the [BRILL

1 Press the [BRILL ] key for a short period of

time to display the menu ([Lcd brill]).

2 Rotate the [GAIN (HF) Knob] or [GAIN (LF)

Knob]. When “1” is selected, it is darkest. When “10” is selected, it is brightest.

Lcd brill

3 Press the [MENU] key to close the menu.

Brightness Adjustment of Panel Brilliance

The brightness of panel can be adjusted.

The [Lcd brill] and [Panel brill] can be switched every time when pressing the [BRILL

1 Press the [BRILL ] key for a short period of

time to display the menu ([Panel brill]).

] key.

Disp

NAV1

Normal (H)

Zoom (H) Dual Freq Zoom (L) Normal (L) NAV2

(H): High frequency

(L): Low frequency

NAV1: Navigation display1

NAV2: Navigation display2

3 Press the [MENU] key to close the menu.

Normal Image (Low frequency, High frequency)

Low frequency

Since the beam width is wide, the search range becomes wide so that the beam can search the deep depth.

High frequency

Since the beam width is narrow, it is hard to be interfered by noise and bubble in the sea so that the schools of fish can be searched in a high resolution.

2 Rotate the [GAIN (HF) Knob] or [GAIN (LF)

Knob]. When “1” is selected, it is darkest. When “10” is selected, it is brightest.

Panel brill

3 Press the [MENU] key to close the menu.

1.4 Switch-over of Display mode

7 kinds of displays are provided in all. Select the display suitable for your purpose.

1 Press the [DISP] key. 2 Select the display you desire to display.

(Press the [ (The set item can be selected by rotating the [GAIN (HF) Knob] or [GAIN (LF) Knob].)

] key or [ ] key.)

Low frequency

(50 kHz)

High frequency

(200 kHz)

1-4 0093112802-06

Page 23

CVS-128/128B Chapter 1 Basic Operation

Dual frequency

The High frequency image can be displayed in the right half side and the Low frequency image can be displayed in the left half side. Since the beam width differs depending on frequency, the schools of fish and sea bottom look different.

Caution: The low frequency screen can be

displayed in the right half of the sceen by replacing the screen and the high frequency screen is displayed in the left harf. (See [2.17 Explanation of Menu Item, Image Swap])

Low frequency image

High frequency image

Zoom (Low frequency, High frequency)

The normal image is displayed in the right half of the screen and the zoom image is displayed in the left half. A part of normal image can be zoomed. (1) [BTM.] (Bottom), (2) [B.D.] (Bottom Discrimination), (3) [Zoom], (4) [B.Z.] (Bottom Zoom) and (5) [B.F.Z.] (Bottom Follow Zoom) are provided for zoom.

The unit is set to (1) [BTM.] at ex-factory. To change to other zoom display, set it in the menu. (See [2.7 Selection of Zoom])

Caution: A ri ght and lef t display can be s witched. (See [2.17 Explanation of Menu Item, Image

Swap])

Zoom type Purpose

Bottom It is convenient to see the

schools of fish near the bottom.

Bottom Discrimination

Zoom

Bottom Zoom It is convenient to see the

It is convenient to see the schools of fish and a bottom quality near the bottom.

It is convenient to see the specified range in the zoom.

schools of fish near the bottom and the form of the bottom.

Zoom start position Zoomed range

It displays the position of the bottom in the fixation in the display bottom part.

It displays the position of the bottom in the fixation in the position of 1/4 under the display.

It displays a zoom start position in the fixation at the top of the display.

It displays the position of the bottom in the position which is the same as the ordinary display.

It displays the bottom and upper in the zoom.

It displays the bottom and upper in the zoom, it displays under the bottom in the ordinary. (Under the bottom, it doesn't display in the zoom).

It displays in the zoom from the zoom start position to the range you set.

It displays upper side of the bottom in the zoom except the bottom.

Bottom Follow Zoom

0093112802-06 1-5

It is convenient to see the schools of fish near the bottom and the form of the bottom.

It always displays the position of the bottom in the lower part of the display.

It displays the bottom and upper and lower sides in the zoom.

Page 24

Chapter 1 Basic Operation CVS-128/128B

(1) Bottom

The display width of zoom is displayed in orange.

Normal image

Zoomed range

(2) Bottom Discrimination

Zoomed range

30.0

Zoom image

The display width of zoom is displayed in orange.

Normal image

(3) Zoom

Zoom start position

30.0

Zoom image

The display width of zoom is displayed in orange.

Normal image

Zoomed range

30.0

Zoom image

1-6 0093112802-06

Page 25

CVS-128/128B Chapter 1 Basic Operation

Depth

Wat

XTE

(4) Bottom Zoom

The display width of zoom is displayed in orange.

Normal image

Zoomed range

(5) Bottom Follow Zoom

Zoomed range

30.0

Zoom image

The image below the bottom

is not zoomed.

The display width of zoom is displayed in orange.

Normal image

30.0

Zoom image

Navigation Menu (NAV1, NAV2)

The navigation menu can be displayed on the left side of the display. To display the information other than depth, sensors need to be connected. (See [1.5 Selection of NAV Display])

Caution: Requires position data from GPS sensor.

er temp

ourse

0093112802-06 1-7

Page 26

Chapter 1 Basic Operation CVS-128/128B

1.5 Selection of NAV Display

Selection of NAV Display

The information can be displayed on the NAV display (NAV 1, NAV2).

Caution:Requires position data from GPS

sensor.

Type of NAV Display

The following images can be displayed on the NAV Display (NAV1, NAV2).

Simple plotter Compass

Speed meter

Depth

Selection of NAV Menu

1 Press the [DISP] key. 2 Select the [NAV1] or the [NAV2]. (Press the

[

] key or [ ] key)

3 [NAV1] is displayed at the right side.

Disp

NAV1 Normal (H)

Zoom (H) Dual freq Zoom (L) Normal (L)

NAV2

NAV1

Display1 Display2 Display3

Display4

4 Press the [ ] key. 5 Select either one of [Display1] to [Display4]

by operating [▲] or [▼] key. At the locations where Display of NAV is shown, a numerical figure 1 , 2 , 3 or 4 is indicated. (The figure below is the case where [Display 1] is selected).

Speed meter

HDG

XTE

The time required

Wind dir.

Wind speed

Lat/Lon

Boat speed

Course

RNG BRG

Water temperature

Heading, XTE, Time required, Wind dir., Wind speed, Depth, Lat/Lon, Boat speed, Course, RNG BRG, Water temp

Depth

NAV1

Display1

Display2 Display3 Display4

Caution: When simple plotter, speed meter

or compass is displayed on the screen, [Display2] and [Display4] cannot be selected.

6 Press the [ ] key.

7 Select the [Display1]. (Press the [ ] key or

[

] key.)

Display1

Simple plotter Compass Speed meter Depth

Lat/Lon Boat speed

Course

8 Press the [MENU] key to close the menu.

1-8 0093112802-06

Page 27

CVS-128/128B Chapter 1 Basic Operation

1.6 Switch-over of Range

The range of measured depth displayed on the display can be changed.

To meet your purpose, select the range of measured depth.

Setting the range switching to auto range

By following automatically the bottom, the image of echo sounder in the suitable range of measured depth can be displayed.

This mode is convenient to display always the range from sea level to bottom.

The range value changes

Setting the range switching to Manual range

The range can be manually selected:

1 Press [▲] or [▼] key of [▲RANGE▼]. 2 Select the range you desire to set. (Press

[▲] or [▼] key of [▲RANGE▼])

Range

uto range

5.0

10.0

20.0

50.0 100 160 300 500

uto shift

3 Press the [MENU] key to close the menu.

When the [Manual] is set, the [R: M] is displayed at the upper side of menu.

1 Press [▲] or [▼] key of [▲RANGE▼]. 2 Select the [Auto Range]. (Press [▲] or [▼]

key of [▲RANGE▼])

Range

uto range

5.0

10.0

20.0

50.0 100 160 300 500

uto shift

3 Press [MENU] to close the menu.

When [Auto Range] is set, the [R:A] is displayed at the upper side of menu.

Caution: At auto range, this sounder can

sound the area up to the maximum sounding registered. The maximum range is 800 m. At the initial setup, the range is up to 200 m for CVS-128 and up to 500 m for CVS-128B. (See [3.6 Setting of Adujust2 Item, Sounding])

1.7 Setting of Shift

The [Shift] (Manual Shift) and [Auto Shift] are provided.

Manual Shift (Shift):

The image range is shifted up and down. (Setting: m, fm, I.fm: 0 ~ 300, ft: 0 ~ 1000)

Caution: Only when the [shift] is

registered in [F1] key or [F2] key, it is effective. It is invalid when not registered. (See [1.10 Use of [F1] / [F2] key)

Caution: When the equipment is shipped

from the factory, the [shift] is registered in the [F2] key.

Auto Shift:

The image is automatically shifted so that the bottom is always displayed.

Setting of Manual Shift

The scope of range starting with the shift value is displayed.

0093112802-06 1-9

Page 28

Chapter 1 Basic Operation CVS-128/128B

1 Press [▲] of [▼] key of [▲RANGE▼]. 2 Select the [Auto shift] (Press [▲] of [▼] key

of [▲RANGE▼])

Range

uto range

5.0

10.0

20.0

50.0 100 160

300

500

uto shift

Range

uto range

5.0

10.0

20.0

50.0 100 160

300

500

uto shift

key or [

Range

40.0

Range

40.0

] key)

1 Press [F2] key twice. The shift function is

turned on.

Shift

OFF

2 Press the [MENU] key to close the menu. 3 Press the [ ] key or [ ] key. 4 Change the set value of [Shift]. (Press the

[

key or [

]

Shift

0~300 m

] key)

5 Press the [MENU] key to close the menu.

Caution: This operation cannot be done

while an auto range or auto shift is working.

Release of manual Shift

3 Press the [ ] key.

4 Select a range at [Auto shift]. (Press the [ ]

5 Press the [MENU] key to close the menu.

When the [Auto shift] is set, the [R : AS] is

The shift function is released, and it returns it to

displayed at the upper side of menu.

former screen.

1 Press twice the [F2] key. The shift function is

turned off.

Shift OFF

2 Press the [MENU] key to close the menu.

Setting of Auto Shift

The image is automatically shifted so that the bottom is always displayed.

1.8 Gain Adjustment

The gain can be adjusted in the auto mode [Cruising, Fishing] or manual mode.

[Cruising]

Eliminating the weak echo, it displays clearly the sea bottom of strong echo. It is suitable for cruising to the fishery ground.

[Fishing]

It displays clearly the weak echo reflected from the school of fish. It is suitable for searching the schools of fish.

1-10 0093112802-06

Page 29

CVS-128/128B Chapter 1 Basic Operation

Basic Operation of Gain

When [GAIN (HF) Knob] or [GAIN (LF) Knob] is

pressed twice, the screen of [Gain select] is displayed.

By rotating the [GAIN (HF) Knob] or [GAIN (LF) Knob], the gain adjustment or auto gain can be selected.

Caution: The high frequency can be set by

[GAIN (HF) Knob] and the low frequency can be set by [GAIN (LF) Knob].

Caution: When only high frequency is

displayed, no gain adjustment at low frequency is available. When only low frequency is displayed, no gain adjustment at high frequency is available.

Selecting the auto gain

When the [Cruising] or [Fishing] is set, the gain can be fine-adjusted.

1 Press [GAIN (HF) Knob] twice, and [Gain

select] is displayed. (The high frequency is explained below.)

Caution: The low frequency can be set by

[GAIN (LF) Knob].

2 Select the [Cruising] or [Fishing] by rotating

the [Knob].

Gain select

Manual

Cruising

Fishing

3 Press the [MENU] key to close the menu.

When the [Cruising] is set, the [L: AC] [H: AC] is displayed at the upper side of menu. When the [Fishing] is set, the [L: AF] [H: AF] is displayed at the upper side of menu.

Caution: The low frequency can be set by

[GAIN (LF) Knob].

2 Fine-adjust the gain by rotating the [GAIN

(HF) Knob]. The [Cursor] key menu position can be moved.

uto adjust high

3 Every time when [GAIN (HF) Knob] is

pressed, the [Gain select] and [Auto adjust high] are alternately displayed.

4 Press the [MENU] key to close the menu.

Selecting the manual gain

Adjustment of gain can be done manually.

1 Press [GAIN (HF) Knob] twice, and [Gain

select] is displayed. (The high frequency is explaied below.)

Caution: The low frequency can be set by

[GAIN (LF) Knob].

2 Select the [Manual] by rotating the [Knob]. 3 Press the [MENU] key to close the menu.

Manual adjustment of the gain

When only the image of High frequency is displayed, the High frequency gain can be adjusted. (Setting: 0 to 10)

When only the image of Low frequency is displayed, the Low frequency gain can be adjusted.

Caution: If you increase the gain too much,

noise will appear on the entire image, resulting in an unclear image. Adjust properly the gain so that the optimum image can be always displayed.

Adjusting the gain by auto

The auto gain adjustment can be set to [Auto adjust high] or [Auto adjust low]. (Setting:-30 ~

10)

1 Turn [GAIN (HF) Knob], and [Auto adjust

high] is displayed. (The high frequency is explained below.)

0093112802-06 1-11

1 Turn [GAIN (HF) Knob] to display [Auto

Over-gain Under-gainOptimum

adjust high]. (The high frequency is explained below.)

Page 30

Chapter 1 Basic Operation CVS-128/128B

Caution: The low frequency can be done

by [GAIN (LF) Knob].

2 Adjust the gain by rotating the [Knob]. The

[Cursor] key menu position can be moved.

Stop increasing of the gain just before noise appears on the image.

Gain(H)

6.0

3 Every time when [GAIN (HF) Knob] is

pressed, the [Gain select] and [Gain (H)] are alternately displayed.

4 Press the [MENU] to close the menu.

The latest set value of frequency (High frequency or Low frequency) adjusted is displayed at the upper left side of menu.

Example: The High frequency gain is 8.0  H: 8.0.

R: M 12.6 VH: 8.0

How to operate the menu])

3 Press the [ ] key. 4 Change the setting of [EVENT key set].

(Press the [

EVENT key set

Store pos

Store image

Fishing hot spot

] key or [ ] key)

5 Press the [MENU] to close the menu.

Presetting the waypoint

When you find the school of fish or tide, its location can be preset as a waypoint. (10 locations at maximum)

When presetting the waypoint, switch [System]  [EVENT Key set]  [Store pos]. (See [1.9 Use of [EVENT] key Selecting the event key function])

1 In the state that no other key is pressed,

press the [

] key or [ ] key.

1.9 Use of [EVENT] key

By pressing the [EVENT] key, three functions of [Store Position]. [Store Image] and [Fishing hot spot] are available.

The fishing hot spot is the function to instruct your boat to navigate easily to a point where you desire to go back.

[Store pos]: The latitude and longitude of a point can be stored in the destination list.

[Store image]: An image of the echo sounder can be stored in the internal memory.

[Fishing hot spot]: The WPT navigation starts, using the latitude and longitude of a point which is set as a destination by pressing the [EVENT] key. Simultaneously, the latitude and longitude of the point can be stored in the destination list.

Caution: Requires position data from GPS

sensor.

Selecting the event key function

Select the functions when pressing the [EVENT] key.

1 Press the [MENU] key. 2 Select [System]  [EVENT Key set]. (Press

the [

] key or [ ] key or [ ] key) (See [2.1

2 Move the cursor (red line) with the [ ] key or

[

] key to the location to be preset as a

waypoint.

Cursor (Red line)

3 Press the [EVENT] key.

When decided, the red line is drawn at the designated location on the echo sounder menu and the latitude and longitude of designated location are registered in the waypoint list. At this moment, the list number of preset waypoint is displayed.

1-12 0093112802-06

Page 31

CVS-128/128B Chapter 1 Basic Operation

Store the image

When you find the schools of fish, its location can

be stored as a waypoint. (10 locations at maximum)

When storing the image, switch [NAV]  [EVENT Key set]  [Store pos]. (See [1.9 Use of [EVENT] key Selecting the event key function].)

1 Press the [EVENT] key.

Processing is displayed.

2 After a certain time passes, the image of

Cursor (Red line)

echo sounder presently displayed is stored and the list number of stored image is displayed.

Image data list # 1 is registered

3 After a certain time passes, the message

disappears and storing the image is finished.

Waypoint list # 1 is registered

Caution: If the

waypoint list is fully filled,

the preset destination list is not deleted, showing the message that the image is fully filled. After a certain time passes, the message disappears.

4 After a certain time passes, the message

disappears and presetting the waypoint is finished.

Caution: When pressing the [EVENT] key,

if [In out]  [NMEA output data]  [TLL] is set to ON, the latitude and longitude of location above-designated is output to the navigation system connected.

Caution: If the waypoint list is full, the

preset destination list is not deleted, showing the message that the list is fully filled. After a certain time passes, the message disappears.

A waypoint list is full. Registration is not completed

Caution: If the waypoint list is full, delete

an unnecessary waypoint from the waypoint list.

list of Pic is full.

Registration is not completed.

As for deletion and recall of images, see [2.15 Store/Recall/Deletion of image].

Fishing hot spot

Leads you back to your favorite fishing hot spots or other previously stored positions in memory with input from optional GPS sensor. (See [2.14 Preset/ WPT edit/ WPT delete of Waypoint])

To perform the fishing hot spot, it is necessary to select [System]  [EVENT key set]  [Fishing hot spot]. (See [1.9 Use of [EVENT] key Selecting the event key function].)

1 In the state that no other key is pressed,

press the [

] key or the [ ] key.

2 Move the cursor (red line) to a point you

desire to go back with the [

] key or [ ] key.

0093112802-06 1-13

Page 32

Chapter 1 Basic Operation CVS-128/128B

1.10 Use of [F1] / [F2] key

L H

Cursor (Red line)

3 Press the [EVENT] key.

When you decide, the red line is drawn on the image of the echo sounder at the point you designate and the latitude and longitude of the point you designate is stored in the destination list. At this moment, the number of the stored destination list is displayed.

4 The navigation display (NAV1) is displayed

and the WPT navigation starts.

Lat/Lon

Note: The display of NAV1 is displayed.

5 To stop the fishing hot spot, cancel

destination navigation. (See: [2.14 Preset/ WPT edit/ WPT delete of Waypoint], [Cancel the NAV].)

At ex-factory, the [Image Speed] is assigned to the [F1] key, and the [Shift] is assigned to the [F2] key. The function settable to the [F1]/[F2] key can be selected among [Image Speed], [IR], [Color Rejection], [Noise Rejection], [Shift], [Zoom Range], [Zoom Start], [A scope], [White line], [Background color], [Disp width], [Nav start], [NAV1], [NAV2], [Image swap], [Image recall] and [Sona-tone]. Set the function frequently used for your convenience.

Selecting the [F1]/[F2] key

1 Press the [F1] key or [F2] key. 2 Select the setting with [

Example [Image speed]

Image speed

Speed1

Speed2

Speed3 Speed4 Stop Speed5 (1/1) Speed6 Speed7 Speed8 Speed9

Caution: When the fish symbol function is

made effective, the image speed becomes two kinds ([Speed5 (1/1)] or [Stop]).

key or [] key.

]

3 Press the [MENU] key to close the menu.

Preset of [F1] / [F2] key

1 Press the [MENU] key. 2 Select [System]  [F1 key set] or [F2 key

set]. (Press the [ key.) (See [2.1 How to operate the menu])

] key or [

key or []

]

3 Press the [ ] key. 4 Select the function. (Press the [

key)

key or []

]

1-14 0093112802-06

Page 33

CVS-128/128B Chapter 1 Basic Operation

F1 key set Image Speed

IR Color Rejection Noise Rejection

Shift Zoom Range Zoom Start

Marker Depth

20.0

Movable marke

scope

White line

Background Colo

5 Press the [MENU] key to close the menu.

The icons of functions preset are displayed at the upper right side on the menu.

←

Image speed

←

Color rejection

←

Noise rejection

←

Shift

←

Zoom Range

←

Zoom Start

← ←

White Line

←

Background colo

scope

←

Image recall

←

Image swap

←

NAV1

←

NAV2

←

Disp width

←

Sona-tone

Other than the above operation method. When keep pressing the [F1] key or [F2] key for few second, the key set menu is displayed.

1.11 Operation of VRM

The VRM (movable marker) shown by the green line can be moved up and down.

It is convenient to measure the depth by aligning with the target such as school of fish.

When displaying dual images, if the [ or [

] key is pressed, the movable marker

] key

moves to the neighboring image.

Caution: When several seconds pass

after finishing the VRM operation, the numerical of marker depth becomes normal display.

Caution: If VRM is moved to the top of

the display, the VRM can be disappeared.

Caution: VRM can be operated by turning

[GAIN (LF) Knob] at the high frequency screen.

Caution: VRM can be operated by turning

[GAIN (HF) Knob] at the low frequency screen.

1.12 Display of fish information

When transducer TD-501C is connected, specific response can be displayed as [Fish symbol].

1 Press the [ ] key or [ ] key. The movable

marker (straight line) is displayed.

For detection of fish information, 2 frequencies, 200 kHz and 50 kHz are used.

2 Press the [ ] key or [ ] key. The movable

marker moves up and down. The movable marker and the numerical of marker depth are simultaneously highlighted.

Only in case echo comes up in both frequencies, the detection can be made.

By [Symbol info], the magnitude and the value of depth of the response can be displayed.

Caution: Fish information is to display the

specific responses in an easy way to watch. Displays of [Fish symbol] do not always mean that there is fish there.

0093112802-06 1-15

Page 34

Chapter 1 Basic Operation CVS-128/128B

Caution: The area where [Fish symbol]

can be displayed is from 3 m to 100 m. (ft: 10 to 330, fm: 2 to 54, I.fm:2 to 60)

Caution: [Fish symbol] is not displayed in

the range that is deeper than 120m. (ft: 350, fm:60, I.fm:70)

Caution: When the fish symbol function is

made effective, the image speed becomes 2 kinds ([Speed5 (1/1)] or [Stop]).

Caution: Adjustment is necessary when

equipped with Inner-hull. (See [2.17 Explanation of Menu Item, Inner-hull].)

Display the fish symbol/Stop the display of fish symbol

1 Press the [MENU] key. 2 Select [Display1]  [Fish symbol]. (Press

the [

] key or [ ] key or [ ] key.) (See [2.1

How to operate the menu])

3 Press the [ ] key. 4 Select the symbol to be displayed on the

screen. (Press the [

Fish symbol

Symbol 1

] key or [ ] key)

5 Press the [MENU] key to close the menu.

When this function is effective, the icon is displayed at the top of the screen.

Caution: When [Fish symbol] on the

screen does not always mean that the response shows fish.

Selecting the symbol info

[Symbol info] is effective only when [Fish symbol]

is displayed.

1 Press the [MENU] key. 2 Select [Display1]  [Symbol info]. (Press

the [

] key or [ ] key or [ ] key.) (See [2.1

How to operate the menu])

3 Press the [ ] key. 4 Select the information associated with [Fish

symbol] (Press the [

] key or [ ] key.)

Caution: The display of [Size] is

expressed in cm.

Symbol info

OFF Depth

Size

B ot t om <=>F is h

5 Press the [MENU] key to close the menu.

Caution: The magnitude by [Symbol info]

would not be always the response from fish. And it may be incorrect due to various environmental conditions. Please take these as reference.

Caution: The value of depth by [Symbol

info] would not be always the response from fish. That shows the point that there was specific response.

Fish symbol detection adjustment

Detection of fish marks can be adjusted.

Select [Correct]  [Detect adjust f].

Caution: If the larger the set values

become, the more fish marks can be displayed with more false detections.

Caution: For Through-hull installation,

adjust between 1 and 4. For Inner-hull installations, adjust between 3 and 6.

Size adjustment

The indicated size of fish marks can be adjusted.

Please correct the size when the indicated value is different from the fish that actually caught.

Select [Correct]  [Size adjust].

The indicated size will change by approximately 10 to 20 percent of the value, per one setting value.

1-16 0093112802-06

Page 35

CVS-128/128B Chapter 1 Basic Operation

Caution: When the value of [Detect

adjust f] is set at 5 or 6, the size of fish can not be specified and there may be cases where no numerical figures are displayed or only "----" is displayed. When there is no display of numerical figures, it is judged that fish are too small. When "---" is displayed, it is judged that fish is too big.

Big fish / Big fish color

The fish bigger than the set value [cm] is specified as big fish.

Select keys of [Display2] [Big fish].

Colors for values of big fish can be assigned.

Select keys of [Display2] [Big fish color].

 [Color table 2]

The values displayed by this function may be incorrect depending on various environmental conditions. In use of these values, please understand the following factors of error, and use them as reference:

[Factors of error]

1 When there are overlapping responses,

2 The strength of reflection may depend on

3 The strength of reflection may depend on

4 Fish banks, fishing net, fishing equipment,

5 When the transducer unit is mounted in

Points to note in use of fish symbol

all of them may be displayed to show the magnitude of a point.

the output of transducer unit and may result in a factor of error.

the kind of fish and may result in a factor of error. As for the fish such as the squid which don't have an air bladder, the error is big.

air bubbles and floating objects, etc. may be detected and displayed.

inner-hull, there may be cases where response cannot be detected depending on attenuation, and large error may be generated.

6 The strength of reflection may depend on

the difference of ship handling such as stoppage and cruising, and may result in a factor of error.

7 Each transducer unit may have difference

in transmission/receiving performance to cause error.

8 When there is dirt in the sea and the

plankton layers have been generated, it becomes the factor of the error margin.

0093112802-06 1-17

Page 36

CVS-128/128B Chapter 2 How to use the menu

Chapter 2 How to use the menu

2.1 How to operate the menu

Display the menu/Stop the display of menu

1 Press the [MENU] key.

The menu and explanation of operation are displayed.

Name of menu selected

Menu column

djust

D.range Display1

Display2

NAV Image System

Freq*

* For CVS-128B

larm1 larm2

Setting item column

Image speed IR

Color rejection

Noise rejection

TX power

Gain (TD) Pulse width*

Band width*

D.Range* Return

Guide

It is displayed when the [Operation Guide] is set to ON.

(See [2.17 Explanation of Menu Item Display the operation guide / Stop the display of operation guide].)

2 Press the [MENU] key.

The menu and explanation of operation close.

Menu Operation

Cursor

Speed 5 Strong 0%

0 Medium TVG

uto

Middle Middle

24dB

Setting value

djust D.range Display1 Display2

larm1

larm2 NAV Image System Freq*

* For CVS-128B

Shift step Zoom type Zoom range Zoom start

Disp width Range preset Return

Bottom

10.0m 0m Center

2 Press the [ ] key.

The cursor appears in the set item column. (The cursor appears by pressing the [GAIN (HF) Knob] or [GAIN (LF) Knob].)

3 Select the set item you desire to change

with the [ (The set item can be selected by rotating the [GAIN (HF) Knob] or [GAIN (LF) Knob])

djust D.range Display1 Display2

larm1

larm2 NAV Image System

Freq* Next

* For CVS-128B

4 Press the [

The set menu corresponding to the selected item is displayed. (It can be displayed by rotating the [GAIN (HF) Knob] or [GAIN (LF) Knob].)

key or [] key.

]

Shift step Zoom type Zoom range Zoom start Disp width Range preset Return

key.

]

1m Bottom

10.0m 0m Center

1 When the menu is displayed, press the [

key or [ Depending on the selected menu name, the content in the set item column at the right side changes. (The menu name can

key to select the menu name.

]

Zoom range

10.0

be selected by rotating the [GAIN (HF) Knob] or [GAIN (LF) Knob].)

5 Change the set content with the [

key.

[

]

key or

]

(It can be changed by rotating the [Knob])

6 Press the [

key.

]

The cursor returns to the set item column.

0093112802-06 2-1

Page 37

Chapter 2 How to use the menu CVS-128/128B

(It can be displayed by rotating the [GAIN (HF) Knob] or [GAIN (LF) Knob])

7 To select the other menu item, press the

[

] key.

The cursor returns to the menu column.

8 Press the [MENU] key to close the menu.

2.2 Changing of Image Speed

The image speed of echo sounder can be changed. Even if the schools of fish and bottom are same, the image changes depending on the image speed.

The image speed becomes slow in the order of [Speed1] [Speed2]····· [Speed9]. When [stop] is selected, the image stops.

Caution: When the fish symbol function

is made effective, the image speed becomes 2 kinds ([Speed5 (1/1)] or [Stop]).

1 Press the [MENU] key.

2.3 Rejection of Interference

Interference Rejection

The interference noise from the echo sounder of other boats can be reduced.

If a neighboring boat uses the echo sounder having the same frequency and pulse transmission rate as those your boat has, the interference noise may be displayed. If you set the interference rejection, the interference noise can be reduced. In the order of weak  strong, the noise rejection capability becomes high.

The difference of images based on the different settings of [Intererence reduction]

Image of school of fish

2 Select the [Adjust]  [Image Speed]. (See

[2.1 How to operate the menu].)

3 Press the [ ] key. 4 Change the setting of [Image Speed].

(Press the [

Image speed

Speed 1 Speed 2

Speed 3 Speed 4 Stop

Speed 5 (1/1)

Speed 6 Speed 7 Speed 8

Speed 9

] key or [ ] key.)

5 Press the [MENU] key to close the menu.

Interference image

OFF

Weak

Strong

1 Press the [MENU] key. 2 Select the [Adjust]  [Interference Rejection].

(See [2.1 How to operate the menu].)

3 Press the [ ] key. 4 Change the setting of [Inference Rejection].

(Press the [

OFF

Weak

Strong

] key or [ ] key.)

2-2 0093112802-06

5 Press the [MENU] key to close the menu.

Page 38

CVS-128/128B Chapter 2 How to use the menu

2.4 Color Rejection of Weak Echo

Color Rejection

The color of weak echo can be rejected.

Rejecting noise on the entire image and weak echo around the school of fish makes it easier to see the school of fish. It is the convenient function when displaying the echo stronger than the specific signal. (Setting: 0 to 50 %)

1 Press the [MENU] key. 2 Select the [Adjust]  [Color Rejection].

(See [2.1 How to operate the menu])

3 Press the [ ] key. 4 Change the setting of [Color Rejection].

(Press the [

Color Rejection

5 Press the [MENU] key to close the menu.

] key or [ ] key.)

5 Press the [MENU] key to close the menu.

2.6 Setting of Shift step

The shifting range is set by pressing the [ key or [ 10m, 1/8, 1/4)

] key one time. (Setting range: 1m,

1 Press the [MENU] key. 2 Select the [D.range]  [Shift step]. (See

[2.1 How to operate the menu])

3 Press the [ ] key. 4 Change the setting of [Shift step]. (Press

the [

] key or [ ] key.)

Shift step

10m 1/8 1/4

5 Press the [MENU] key to close the menu.

]

2.5 Rejection of Noise

Noise Rejection

The influence of noise can be reduced.

Due to echo reflected from plankton and trash, the speck-like noise may appear on the entire image. Setting the [Noise rejection] reduces the speck-like noise and makes it easier to see the image of school of fish. (Setting: 0 to 10)

The greater the set value becomes, the stronger the effect of noise rejection becomes.

1 Press the [MENU] key. 2 Select [Adjust]  [Noise rejection]. (See

[2.1 How to operate the menu])

3 Press the [ ] key. 4 Change the setting of [Noise rejection].

(Press the [

Noise Rejection

] key or [ ] key)

Caution: When the shift is set to 1/4

with 100m range, it shifts by 25m.

2.7 Selection of Zoom

Set the zoom display with the display mode ([zoom (H)] or [zoom (L)].

The [Bottom], [Bottom Discrimination], [Zoom], [[Bottom Zoom] and [Bottom Follow Zoom] are provided. (See [1.4 Switch-over of Menu])

1 Press the [MENU] key. 2 Select [D.range]  [Zoom type]. (See [2.1

How to operate the menu])

3 Press the [ ] key. 4 Select the zoom type. (Press the [ ] key or

[

] key)

0093112802-06 2-3

Page 39

Chapter 2 How to use the menu CVS-128/128B

Zoom type BTM.

B.D. Zoom B.Z. B.F.Z.

5 Press the [MENU] key to close the menu.

For each zoom display, refer to [1.4 Switch-over of Display mode].

2.8 Setting of Zoom Range

Set the zoom range in each mode of [BTM], [Bottom Discrimination], [Zoom], [Bottom Zoom] and [Bottom Follow Zoom]

The zoom range of each mode is identical.

(See [1.4 Switch-over of Display mode]) (Setting: m: 2.5 to 200, fm, I.fm: 2.5 to 150, ft:10.0 to 650)

2.9 Setting of Zoom Start

Select the zoom start in the [Zoom]. (See [1.4 Switch - over of Display mode])

(Setting: m: 0 to 800, fm, I.fm: 0 to 500, ft: 0 to

2600)

Zoom Start

1 Press the [MENU] key 2 Select [D. range]  [Zoom start] (See [2.1

How to operate the menu])

3 Press the [ ] key.

Zoom Range

1 Press the [MENU] key. 2 Select [D. range]  [Zoom range]. (See

[2.1 How to operate the menu])

3 Press the [ ] key. 4 Change the set value of [Zoom range].

(Press the [

Zoom Range

] key or [ ] key)

10.0

5 Press the [MENU] key to close the menu.

4 Change the set value of [Zoom start].

(Press the [

Zoom start

0~800 m

0-800

] key or [ ] key)

5 Press the [MENU] to close the menu.

2.10 Preset of Range

The range switched with the [ can be set.

Preset the set value suitable for your purpose. (Setting range: m: 2.5 to 1200, fm, I.fm: 2.5 to 700, ft: 10 to 3600)

1 Press the [MENU] key. 2 Select [D.range] [Range preset]

[Range 1 to 8]. (See [2.1 How to operate the menu])

RANGE ] key

3 Press the [ ] key.

2-4 0093112802-06

Page 40

CVS-128/128B Chapter 2 How to use the menu

4 Select [Range 1 to 8]. (Press the [ ] key or

[

] key)

djust

D.range

Disp1 Disp2

larm1 larm2

NAV

Image

System Freq* Next

* For CVS-128B

Prev Range 1

Range 2

Range 3

Range 4

Range 5 Range 6

Range 7

Range 8

Return

5.0 m

10.0 m

20.0 m

50.0 m

100 m 160 m 300 m 500 m

Caution: Select [Forward], and press [

key to return to the previous menu.

5 Press the [ ] key. 6 Select the set value of [Range 1 to 8].

(Press the [

Range1

key or [] key)

]

20.0

7 Press the [MENU] key to close the menu.

Easy registration method of the range

1 Press [▲] or [▼] key of [▲RANGE▼]. 2 Change the range you desire to set. (Press

[▲] or [▼] key of [▲RANGE▼])

Range

uto range

5.0

10.0

20.0

50.0 100 160 300 500

uto shift

Range1

5 When the [ ] key is pressed, it returns to

the [range]. Other detecting range can be continuously changed.

6 Press the [MENU] key to close the menu.

2.11 Setting of Background Color

Responding to the ambient brightness, the

]

background color of display can be changed.

1 Press the [MENU] key. 2 Select [Display1]  [Background color].

(See [2.1 How to operate the menu])

3 Press the [ ] key. 4 Change the setting of [Background color].

(Press the [

Background color

Pale blue

Marine blue

Blue Dark blue Black Darkkhaki Mediumseagreen Light grey White

Night mode

] key or [ ] key)

5 Press the [MENU] to close the menu.

2.12 Setting of White Line

As the surface of bottom is marked with the white line of constant width, the school of fish at the bottom can be easily identified.

3 Press the [ ] key.

4 Select the set value of Range. (Press the

[

key or [] key)

]

0093112802-06 2-5

Page 41

Chapter 2 How to use the menu CVS-128/128B

range. It is convenient for you to judge whether the echo of school of fish is present or not. (Setting: m: 1 to 800, fm, I.fm: 1 to 700, ft: 1 to

2800)

Caution: In the [Level], select the

strength of echo reflected from the

hite line

1 Press the [MENU] key 2 Select [Display1]  [White line]. (See [2.1

How to operate the menu])

3 Press the [ ] key. 4 Change the setting of [White line].

“1” is narrowest. “5” is widest. In the auto mode, responding to the strength of echo reflected from the bottom, the width of white line changes. (Press the [

] key or [ ] key)

White line

OFF

2 3 4 5 Auto

schools of fish in the [Fish alarm].

[Water temp alarm] issues when the water temp is within or out of the set range. It is convenient to keep the specific water temp region. (Setting:

- 5 to 45 ºC, 23 to 113 ºF)

[Speed alarm] issues when the boat speed is faster or slower than the set range. It is convenient when the speed limit is obliged. (Setting: 0 to 80 kn, 0 to 148 km/h)

[Arrival alarm] can be used in the state that the destination is set. The alarm is issued when your boat arrives within a certain range of destination. A certain range is set in the [NAV alarm range]. (See [1.9 Use of [EVENT] key.)

[XTE alarm] can be used in the state that the destination is set. The alarm is issued when your boat is off a certain distance from the course on the line drawn straightly from destination to the location when setting the destination. A certain distance is set in the [NAV alarm range].

Caution: In the [NAV alarm range], select

the alarm range of [Arrival alarm] and [XTE alarm]. (Setting: 5 to 999 m)

5 Press the [MENU] key to close the menu.

2.13 Setting of Alarm

Caution: The setting range of [Arrival

alarm] and [XTE alarm] can not be separately set.

6 alarms of bottom alarm, fish alarm, water temp alarm, speed alarm, arrival alarm and XTE alarm can be set.

They are notified by alarm sound and alarm display.

[Bottom alarm] issues the alarm when the position recognized as the bottom is shallower than the upper limit or deeper than the lower limit. It is convenient when keeping the specific depth. (Setting: m: 0 to 800, fm, I.fm: 0 to 700, ft: 0 to 2800)

[Fish alarm] issues the alarm when an echo recognized as school of fish exists in the set

2-6 0093112802-06

Stopping the alarm sound

To stop the alarm sound and the alarm display, press [MENU] key.

Page 42

CVS-128/128B Chapter 2 How to use the menu

Setting the alarm

djust

D.range

Disp1 Disp2

larm1 larm2

NAV Image System

Freq*

djust

D.range Disp1

Disp2

larm1 larm2

NAV Image System

Freq*

* For CVS-128B

Bottom alarm

Upper depth Lower depth

Fish alarm

Position Range Level

Return

Water temp alarm

Upper temp alarm Lower temp alarm

Speed alarm

Speed limit

rrival alarm XTE alarm NAV alarm range

Return

1 Press the [MENU] key.

OFF

5m 50m

OFF

5m 50m Medium

OFF

20.0ºC

15.0ºC

OFF

0kn

OFF OFF 10m

Confirm the alarm state

The set state of [Bottom alarm] and [Fish alarm] can be confirmed on the bar at the right corner of display. However, when the display is out of the range, they are not displayed.

When [Water temp alarm], [Speed alarm], [Arrival alarm] or [EXT alarm] is ON, the corresponding icon is displayed at the upper side of the screen.

[ XTE alarm]

[

rrival alarm

Speed alarm

[

Water temp alarm

[

]

] ]

Bottom alarm

[

Fish alarm

[

]

2 Select your desired alarm from [Alarm 1] or

[Alarm 2]. (See [2.1 How to operate the menu].)

3 Press the [ ] key. 4 Select the [ON] of alarm you desire. (Press

] key or [ ] key)

the [

5 If the setting of [Alarm range] is provided in

the alarm desired, select the alarm range. (See [2.1 How to operate the menu])

6 Change the set value of alarm range.

(Press the [

] key or [ ] key)

7 Press the [MENU] key to close the menu.

Release the alarm

1 Press the [MENU] key. 2 Select the alarm to be released from

[Alarm 1] or [Alarm 2]. (See [2.1 How to operate the menu])

3 Press the [ ] key. 4 Select the [OFF] of alarm to be released.

(Press the [

] key or [ ] key)

5 Press the [MENU] key to close the menu.

0093112802-06 2-7

Page 43

Chapter 2 How to use the menu CVS-128/128B

2.14 Preset/WPT edit/WPT delete of Waypoint

NAV Start

The NAV can be started by selecting the destination from the destination list.

To perform the NAV start, the destination must be preset. (See [1.9 Use of [EVENT] key]

Caution: Requires position data from

GPS sensor.

1 Press the [MENU] key. 2 Select [NAV]  [NAV start]. (See [2.1 How

to operate the menu])

3 Press the [ ] key. 4 Select the [Destination list] preset. (Press

the [

] key or [ ] key)

)

Cancel the NAV

The NAV started can be cancelled halfway.

1 Press the[MENU] key 2 Select [NAV]  [NAV cancel]. (See [2.1

How to operate the menu])

3 Press the [ ] key. 4 Press the [Yes]. (Press the [ ] key or [ ]

key)

NAV cancel

Yes

5 Press the [MENU] key. Then, the NAV is

released.

6 To return the display to the original one,

the display mode shall be switched over. (See: [1.4 Switch-over of Display mode])

Edit the destination

Caution: The list No. selected is reversed

in yellow.

5 Press the [ ] key. 6 Select the [Yes] in the confirmation menu.

(Press the [

NAV starts

Yes

] key or [ ] key)

7 Press the [MENU] key.

Then, the NAV starts.

By entering the latitude and longitude, the destination can be preset.

The list preset in the past can be edit.

1 Press the [MENU] key. 2 Select [NAV]  [WPT edit]. (See [2.1 How

to operate the menu])

3 Press the [ ] key. 4 Select the list No. to be edited from the

[WPT edit] list. (Press the [ key)

] key or [ ]

5 Press the [

key.

]

6 Select the character with the [ ] key or [ ]

2-8 0093112802-06

Page 44

CVS-128/128B Chapter 2 How to use the menu

key. (Character: A ~ Z, blank, 0 ~ 9, +, -./ Lat/Lon: 0~9,N,S,E,W)

7 Move the position of characters to be

reversed with the [

] key or [ ] key.

Delete the waypoint

The destination list preset in the past can be deleted.

The deletion takes some time.

1 Press the [MENU] key. 2 Select [NAV]  [WPT delete]. (See [2.1

How to operate the menu])

3 Press the [ ] key. 4 Select the list number of destination to be

deleted from the [WPT delete]. (Press the [

] key or [ ] key)

Caution: If the values of latitude and

longitude are not entered, they are registered as 0.

8 To end editing, press [GAIN (HF) Knob] or

[GAIN (LF) Knob].

9 After finishing the edit work, press the

[MENU] key.

10 Select the [registered] in the confirmation

menu.

Edit end Registered

Not registered

11 Press the [MENU] key. Then, the edit is

finished.

5 Press the [ ] key. 6 Select the [Yes] in the confirmation menu.

(Press the [

WPT delete

Yes

] key or [ ] key)

7 Press the [MENU] key. Then, the

destination is deleted and the menu closes.

Recall the stored image and preset it as a destination

Recall the stored image in the past and it can be preset as a destination. [EVENT] key]

)

(See [1.9 Use of

1 Press the [MENU] key. 2 Select [Image]  [Image recall]. (See [2.1

How to operate the menu].)

3 Press the [ ] key. 4 Select the image No. from the [Image

0093112802-06 2-9

Page 45

Chapter 2 How to use the menu CVS-128/128B

）

recall] list. (Press the [

Image recall

No.

Comment

P IC 0 0 0 0 1

P IC 0 0 0 02 P IC 0 0 0 03

3 4

P IC 0 0 0 04 P IC 0 0 0 05

P IC 0 0 0 06

P IC 0 0 0 07

P IC 0 0 0 08

P IC 0 0 0 09

010

P IC 0 0

Caution: Chosen list NO. becomes

yellow.

] key or [ ] key)

5 Press the [ ]key. 6 Move the cursor to the location preset as a

destination with the[ select it.

key or [

]

] key and

2.15 Store / Recall / Deletion of Image

Store the image

The present image of echo sounder can be stored.

To memorize, it takes some time.

To memorize the image, the [EVENT] key must be switched to the [Store image].

1 Press the [MENU] key. 2 Select [System]  [EVENT key set]. (See

[2.1 How to operate the menu])

3 Press the [ ] key. 4 Select the [Store image]. (Press the [ ]

key or [

EVENT key set

Store pos

Store image

Fishing hot spot

] key)

Caution: You can switch to other stored

image with the [

Cursor（red line

] or [ ] key.

7 When starting the NAV, press the [EVENT]

key. When not starting the NAV, press the [MENU] key.

5 Press the [MENU] key to close the menu. 6 When the echo sounder image to be

stored appears, press the [EVENT] key.

7 When the stored image is fully filled, it

shows that the [Store image] is fully filled. After deleting the unnecessary image, try it again.

Recall the stored image

The stored image in the past can be recalled.

During recalling, the image cannot be stored.

1 Press the [MENU] key. 2 Select [Image]  [Image recall]. (See [2.1

How to operate the menu])

3 Press the [ ] key. 4 Select the number of image to be recalled

from the [Image recall] list. (Press the [ key or [

] key)

]

2-10 0093112802-06

Page 46

CVS-128/128B Chapter 2 How to use the menu

Image recall

No.

Comment

I C0 0 0 0 1

P I C0 0 0 02

I C0 0 0 03

I C0 0 0 04

I C0 0 0 05

I C0 0 0 06

I C0 0 0 07

I C0 0 0 08

I C0 0 0 09

010

I C0 0

Caution: Chosen list NO. becomes

yellow.

5 Press the [ ] key.

Caution: When other stored image

exists beside the recall image, switch to other image with the [ and [

key.

]

6 Press the [MENU] key to return to the

normal menu.

Delete the stored image

The stored image in the past can be deleted.

To delete, it takes some time.

1 Press the [MENU] key. 2 Select [Image]  [Image delete]. (See [2.1

How to operate the menu])

3 Press the [ ] key. 4 Select the number of image to be deleted

from the [Image delete] list. (Press the [ key or [

Image delete

No. Comment 1 2 3 4 5 6 7 8 9 10

] key)

C0 0 0 0 1

PI C0 0 0 02

C0 0 0 03

PI PI

C0 0 0 04 C0 0 0 05

C0 0 0 06

C0 0 0 07

C0 0 0 08

C0 0 0 09

010

C0 0

5 Press the [ ] key.

6 Select the [Yes] in the confirmation menu.

Image delete

Yes

7 Press the [MENU] key.

Then, the preset image is deleted.

Add the comment to the stored image

It is convenient to judge the stored image.

1 Press the [MENU] key. 2 Select [Image]  [Image comment]. (See

[2.1 How to operate the menu])

3 Press the [ ] key. 4 Select the number of image to which the

comment is added from the [Image comment]. (Press the [

Image comment

No. Comment

PIC00001

PIC00002

PIC00003

PIC00004

PIC00005

PIC00006

PIC00007

PIC00008

PIC00009

PIC00010

]

] key or [ ] key)

5 Press the [ ] key. 6 Select the character with the [

key. (Character: A ~ Z, blank, 0 ~ 9, +, -./)

Image comment

No. Comment 1

P IC00001

P IC00002

P IC00003

key or []

]

7 Select the comment position with the [ ]

key or [

] key.

0093112802-06 2-11

Page 47

Chapter 2 How to use the menu CVS-128/128B

Image comment

Comment

No. 1

P I C0 0 0 0 1

P I C0 0 0 02

I C0 0 0 03

8 To stop editing, press [GAIN (HF) Knob] or

[GAIN (LF) Knob].

9 After finishing the edit, press the [MENU]

key.

10 Select the [register] in the confirmation

menu.

Edit end Registered

Not registered

11 Press the [MENU] key. Then, the edit is

finished.

2.16 Explanation of Sonar

Switch-over of Sona-ToneTM

The Sona-ToneTM can be output to the built-in speaker by selection.

Connection of External Speaker

Connect the external speaker with amplifier (option) so that you can hear the sonar easily.

Caution: The Sona-Tone

output. Adjust the speaker volume with the volume provided on the speaker.

Caution: The external speaker is an

option.

is always

2.17 Explanation of Menu Item

The various items in the menu are explained.

Inner-hull

The reduction in sensitivity due to signal attenuation in inner-hull use can be corrected. (Setting: - 50 ~ 50: through-hull: 0)

1 Press the [MENU] key. 2 Select the [Adjust]  [Gain (TD)]. (See

[2.1 How to operate the menu])

3 Press the [ ] key. The image displays

bottom only. It may show very strong fish targets.

The schools of fish and condition of bottom on the display of echo sounder can be confirmed by hearing the sonar.

1 Press the [MENU] key. 2 Select the [System]  [Sona-tone]. (See

[2.1 How to operate the menu])

3 Press the [ ] key. 4 Select the [ON] or [OFF] of [Sona-tone].

(Press the [

Sonar tone

Sona-tone

OFF

] key or [ ] key)

5 Press the [MENU] key to close the menu.

4 Set a value to display the sea bottom

continuously without interruption. For high frequency, turn [GAIN (HF) knob] and for low frequency, turn [GAIN (LF) knob].

Gain (TD) L

Gain (TD)

Gain (TD) H

Bottom

5 Press the [MENU] key to close the menu.

2-12 0093112802-06

Page 48

CVS-128/128B Chapter 2 How to use the menu

Caution: Gain (TD) setting value widely

varies upon installation conditions such as material of hull and installation method. Low frequency (50 kHz) may not be used due to large signal attenuation in some cases.

TVG

The TVG adjusts the difference of strength between echoes reflected from the shallower depth and echoes reflected from deeper depth so that the reflection can be uniformed.

The deeper the depth is, the weaker the reflected signal of echo sounder becomes due to attenuation. Thus, comparing the signal reflected from the fish of the same size, the signal reflected from the fish in the shallower depth is stronger than that in the deeper depth. The TVG adjusts the echo signal reflected from the shallower depth to be equal to that reflected from deeper depth by decreasing the receiver gain so that the effect that the strength of echo signal reflected from the shallower depth looks the same as that reflected from the deeper depth provided. The level of adjustment due to the depth increases in the order of weak → medium → strong. When set to "Strong", the TVG provides strongest effect that reduces various noises around oscillation line.

1 Press the [MENU] key.

2 Select the [Adjust]  [TVG]. (See [2.1 How

to operate the menu])

Change the TX power

The strength of transmission output (power) can be changed.

When the noise of interference with the neighboring echo sounder occurs, if the powers of transmission outputs at both sides are weakened, the interference noise can be suppressed.

1 Press the [MENU] key. 2 Select the [Adjust]  [TX power]. (See [2.1

How to operate the menu])

3 Press the [ ] key. 4 Select the [TX power]. (Press the [ ] key

or [

] key.)

TX power

30 40 50

60 70 80 90 100

Auto

5 Press the [MENU] key to close the menu.

Caution: In [Auto] setting, it controls

transmission power automatically.

3 Press the [ ] key. 4 Select the [weak], [medium], [strong].

(Press the [

TVG

Weak

Medium

Strong

] key or [ ] key)

5 Press the [MENU] key to close the menu.

Caution: When the setting of [Gain

select] is either one of [Cruising] or [Fishing], it cannot be selected.

0093112802-06 2-13

Change the Pulse width

Resolution and the detection distance change by changing the transmission pulse width. As for [Super short], the detection distance shortens though resolution goes up. As for [Long], the detection distance becomes long though resolution falls.

1 Press the [MENU] key. 2 Select the [Adjust] → [Pulse width]. (See

[2.1 How to operate the menu])

3 Press the [ ] key. 4 Change the setting of [Pulse width]. (Press

the [

] key or [ ] key.)

5 Press the [MENU] key to close the menu.

Page 49

Chapter 2 How to use the menu CVS-128/128B

Caution: When the fish symbol

function is made effective, this function becomes invalid.

For CVS-128B

Change the Bandwidth

The bandwidth is automatically set according to the transmission pulse width. Please make it to [Narrow] when you decrease the noise. Please make it to [Super narrow] when you decrease more.

1 Press the [MENU] key. 2 Select the [Adjust] → [Bandwidth]. (See

[2.1 How to operate the menu])

3 Press the [ ] key. 4 Change the setting of [Bandwidth]. (Press

the [

] key or [ ] key.)

5 Press the [MENU] key to close the menu.

Caution: When the fish symbol function

is made effective, this function becomes invalid.

For CVS-128B

D.Range

D.Range is to expand and narrow down the signal range from blue to red in images.

When the value is small, the expression range of strong and weak signal change is narrow, weaker signal will become undistinguished. When the value is larger, the expression range is wider and the weaker signals become distinct. (Setting: 12 to 30dB)

1 Press the [MENU] key. 2 Select the [Adjust] → [D.Range]. (See [2.1

How to operate the menu])

3 Press the [ ] key. 4 Change the setting of [D.Range]. (Press

] key or [ ] key.)

the [

5 Press the [MENU] key to close the menu.

For CVS-128B

Display Width

When the image is zoomed or dual frequency displayed, the display width can be changed.

1 Press the [MENU] key. 2 Select the [D.range]  [Disp. width]. (See

[2.1 How to operate the menu])

3 Press the [ ] key. 4 Select the width of image. (Press the [ ]

key or [

] key)

5 Press the [MENU] key to close the menu.

Display the A scope/Stop the display of A scope

The echo strength of latest echo can be displayed at the right side of echo sounder display.

The strength of echo sounder image is expressed by the horizontal width. This expression is called [A scope].

The width for strong echo is wide and the width for weak echo is narrow. This makes it easier for you to see the echo.

1 Press the [MENU] key. 2 Select the [Display1]  [A scope]. (See

[2.1 How to operate the menu])

3 Press the [ ] key. 4 To display the A scope, select the [ON].

To stop the display of A scope, select the [OFF]. (Press the [

] key or [ ] key)

5 Press the [MENU] key to close the menu.

Change the display color of echo sounder image

The [Monochrome], [8 color], [16 color] and [64 color] can be selected.

1 Press the [MENU] key. 2 Select the [Display1]  [Color tone]. (See

[2.1 How to operate the menu])

3 Press the [ ] key. 4 Select the [Color tone]. (Press the [ ] key

or [

] key)

5 Press the [MENU] key to close the menu.

2-14 0093112802-06

Page 50

CVS-128/128B Chapter 2 How to use the menu

Change the depth value

The display size of depth value can be changed.

1 Press the [MENU] key. 2 Select the [Display1]  [Depth value].

(See [2.1 How to operate the menu])

3 Press the [ ] key. 4 Select the size of display. (Press the [ ]

key or [

] key)

5 Press the [MENU] key to close the menu.

Display the depth unit / Stop the display of depth unit

The depth unit can be displayed.

1 Press the [MENU] key. 2 Select the [Display1] → [Unit display]. (See

[2.1 How to operate the menu])

3 Press the [ ] key. 4 To display the depth unit, select the [ON].

To stop the display of depth unit, select the [OFF]. (Press the [

] key or [ ] key)

5 Press the [MENU] key to close the menu.

Display the water temp graph/Stop the display of water temp graph

The latest water temp value and the graph of past water temp data can be displayed.

1 Press the [MENU] key. 2 Select the [Display1]  [Water temp

graph]. (See [2.1 How to operate the menu])

3 Press the [ ] key. 4 To display the water temp graph, select the

[ON]. To stop the display of water temp graph, select the [OFF]. (Press the [ key)

] key or [ ]

5 Press the [MENU] key to close the menu.

Setting of the background color of NAV display

The color of background of navigation display

(NAV1, NAV2) can be changed.

1 Press the [MENU] key. 2 Select the [NAV]  [Background color].

(See [2.1 How to operate the menu].)

3 Press the [ ] key. 4 Select the [Background color]. (Press the

[

] key or [ ] key)

5 Press the [MENU] key to close the menu.

Setting of the echo sounder display at NAV display

The sounder display can be selected at NAV (NAV 1, NAV 2) to be displayed.

1 Press the [MENU] key. 2 Select the [NAV]  [NAV1 (2)]. (See [2.1

How to operate the menu])

3 Press the [ ] key. 4 Select the echo sounder display at [NAV 1]

or [NAV 2] to be displayed. (Press the [ key or [

key)

]

5 Press the [MENU] key to close the menu.

Image Swap

The images of echo sounder at the right and left sides can be swapped.

1 Press the [MENU] key. 2 Select the [Image]  [Image swap]. (See

[2.1 How to operate the menu])

3 Press the [ ] key. 4 Select the swap state [A|B],[B|A]. (Press

the [

] key or [ ] key)

5 Press the [MENU] key to close the menu.

Display the Operation guide/Stop the display of Operation guide

When displaying the menu, it sets whether or not the operation guide is displayed at the lower part on the display.

0093112802-06 2-15

Page 51

Chapter 2 How to use the menu CVS-128/128B

When setting to “No display of operation guide”, the echo sounder image can be easily seen at the menu operation.

1 Press the [MENU] key. 2 Select the [System]  [Operation guide].

(See [2.1 How to operate the menu])

3 Press the [ ] key. 4 To display the Operation guide, select [ON].

To stop the display of Operation guide, select [OFF]. (Press the [

] key or [ ] key)

5 Press the [MENU] key to close the menu.

Display the detection area/Stop the display of detection area

The range of the search that can be detected in the angle of beam spread of the transducer used can be displayed.

1 Press the [MENU] key. 2 Select the [Display2]  [Detection area].

(See [2.1 How to operate the menu])

3 Press the [ ] key. 4 To display the Detection area, select [ON].

To stop the display of Detection area, select [OFF]. (Press the [

] key or [ ] key)

5 Press the [MENU] key to close the menu.

Caution: The beam angle of transducer

is different depending on the transducer. (See [3.3 Setting of Correct Item, Directirity angle (Low/High)].)

Setting of Scale display

The set of the scale display

1 Press the [MENU] key. 2 Select the [Display2]  [Scale display].

(See [2.1 How to operate the menu])

3 Press the [ ] key. 4 Select the [Scale display]. (Press the [ ]

key or [

] key)

5 Press the [MENU] key to close the menu.

Change the scale value

The display size of the scale value can be changed.

1 Press the [MENU] key. 2 Select the [Display2]  [Scale]. (See [2.1

How to operate the menu])

3 Press the [ ] key. 4 Select the [Scale]. (Press the [ ] key or

[

] key)

5 Press the [MENU] key to close the menu.

Change the image direction

The direction of display image can be changed.

1 Press the [MENU] key. 2 Select the [Display2]  [Image direction].

(See [2.1 How to operate the menu])

3 Press the [ ] key. 4 Select the [Image direction]. (Press the [ ]

key or [

] key)

5 Press the [MENU] key to close the menu.

Setting of Depth measurement

Select the method for depth measurement, which is shown on the display.

1 Press the [MENU] key. 2 Select the [Display2]  [Bottom detection].

(See [2.1 How to operate the menu])

3 Press the [ ] key. 4 Select the [Bottom detection]. (Press the

[

] key or [ ] key)

5 Press the [MENU] key to close the menu.

Change the display color

The display color can be changed.

1 Press the [MENU] key. 2 Select the [Display2]  [Color table 1] or

[Color table 2]. (See [2.1 How to operate the menu])

3 Press the [ ] key. 4 Select the [Color table]. (Press the [ ] key

2-16 0093112802-06

Page 52

CVS-128/128B Chapter 2 How to use the menu

or [ ] key)

5 Press the [ ] key.

6 Select the color. (Press the [ ] key or [ ]

key)

7 Press the [MENU] key to close the menu.

Setting of Key lock

Disable the functions of controls and keys to avoid deviation of these settings by unintentionally touching them during operation.

1 Press the [MENU] key. 2 Select the [System]  [Key lock]. (See [2.1

How to operate the menu])

3 Press the [ ] key. 4 Select the [Key lock]. (Press the [ ] key or

[

] key)

5 Press the [ ] key. 6 Select the [ON] or [OFF]. (Press the [ ]

key or [

] key)

7 Press the [MENU] key to close the menu.

key or [

Black  0, , , 176, , , 255  Red

] key)

5 Press the [MENU] key to close the menu.

Change the image partition

The image partition of echo sounder can be change to "Horizontal split" or “Vertical split”.

1 Press the [MENU] key. 2 Select the [Image]  [Image partition].

(See [2.1 How to operate the menu])

3 Press the [ ] key. 4 Select the [Image partition]. (Press the [ ]

key or [

] key)

5 Press the [MENU] key to close the menu.

Display the frequency / Stop the display of frequency

The frequeny of the transducer currently in use can be displayed.

Change the scale type

The interval of indications of scale can be changed.

1 Press the [MENU] key. 2 Select the [Display2]  [Scale type]. (See

[2.1 How to operate the menu])

3 Press the [ ] key. 4 Select the [Scale type]. (Press the [ ] key

or [

] key)

5 Press the [MENU] key to close the menu.

Change the bottom color

The dark red color of sea bottom can be changed.

1 Press the [MENU] key. 2 Select the [Display2]  [Color table 2]

[Bottom color]. (See [2.1 How to operate the menu])

3 Press the [ ] key. 4 Select the [Bottom color]. (Press the [ ]

1 Press the [MENU] key. 2 Select the [Display2] → [Freq display].

(See [2.1 How to operate the menu])

3 Press the [ ] key. 4 To display the Freq display, select the [ON].

To stop the display of Freq display, select the [OFF]. (Press the [

] key or [ ] key)

5 Press the [MENU] key to close the menu.

For CVS-128B

Selecting a display area of fish symbol indication

The fish symbol can be displayed either on side A or on side B, or on both sides, by the following operation.

1 Press the [MENU] key. 2 Select the [Image]  [Fish image]. (See

[2.1 How to operate the menu])

3 Press the [ ] key. 4 Select the [A|B], [A| ], [ |B]. (Press the [ ]

key or [

] key)

5 Press the [MENU] key to close the menu.

0093112802-06 2-17

Page 53

CVS-128/128B Chapter 3 How to use the menu2

Chapter 3 How to use the menu2

3.1 Display of Menu

After powering on, besides the menu displayed first with the [MENU] key, there are the other menus as follows, of which setting does not need to be frequently changed.

[In out], [Correct], [Setting], [Maintain]

Display the menu

1 Press the [MENU] key. 2 Select the [Next].

djust

D.range Display1

Display2

larm1

larm2 NAV Image System

Freq* Next

* For CVS-128B

3 Press [ ] key to display the system menu.

Prev In out Correct Setting Maintain

* For CVS-128B

Return to the normal menu

Select the [Prev].

1 2 Press the [ ] key to display the normal

menu.

In out Correct Setting Maintain

djust2

djust

D.range Display1 Display2

larm1 larm2

NAV Image Freq* System

3.2 Setting of External Input / Output

Set the setting related to the input/output.

Prev In out Correct Setting Maintain

Buzzer Setting

Set the buzzer sound to ON/OFF.

Temp Source

Switch the Sensor/NMEA. For setting of [SENSOR], use an internal water

thermometer connected to the water temperature sensor with J6 connector.

For setting of [NMEA], use the input value from outside connected with NMEA of power connector.

Speed Source

Switch the Sensor/NMEA. Use the built-in speed meter for sensor. Use the external input value for NMEA.

Baud Rate

Change the transmission speed of external input/output.

Match the transmission speed with that of external equipment connected. (Setting: 4800, 9600, 19200, 38400)

Buzzer setting Temp source Speed source Baud rate NMEA monitor NMEA output data NMEA output data Return

OFF InsideSensor InsideSensor 4800 OFF

0093112802-06 3-1

Page 54

Chapter 3 How to use the menu2 CVS-128/128B

NMEA Monitor

The external input data can be displayed. To return to the original menu, press the [MENU]

key.

Caution: When [GAIN (HF) Knob] is

pressed, the displayed data will stop.

NMEA Output Data

The output of NMEA sentence can be set to ON/OFF.

1 Select [In out]  [NMEA output data]. (See

[2.1 How to operate the menu].)

2 Press the [ ] key. 3 Select the sentence name.

4 Press the [ ] key.

Prev In out Correct Setting Maintain

Prev DBT DPT GGA MTW TLL VHW

VTG ZDA Return

ON ON OFF OFF ON OFF OFF

OFF

3.3 Setting of Correction Item

In out Correct Setting

Maintain

Draft Set

The tolerance of depth can be corrected. Set the depth from the sea level to the set depth

of your transducer . Normally set draft value of your boat. (Setting: expect ft: - 10.0 to 10.0, ft:

-30.0 to 30.0)

Sonic Speed

Set the [Seawater] or [Freshwater]. Change to meet the usage.

Draft set Sonic speed Water temp Boat speed Beam width H

Beam width L Size adjust Detect adjust f

Bubble Bubble time set

Return

0.0m Seawater

0.0°C 0%

17° 50°

OFF 5 minutes

5 Select the ON/OFF.

DBT

OFF

6 Press the [ ] key to turn to the display to

select the sentence name.

7 Further pressing of [ ] key turns to the

display to select the NMEA output.

8 Press the [MENU] key to close the menu.

Water Temp

The error of water temp value can be corrected. (Setting: - 10.0 to 10.0 ˚C, - 10.0 to 10.0 ˚F)

Boat Speed

The tolerance of boat speed value can be corrected.

When the [Speed source] is set to [Sensor], it is corrected by %. (Setting: - 50 to 50 %)

When the [Speed source] is set to [NMEA], it is corrected by numeral. (Setting: - 10.0 to 10.0)

Directivity angle (Low/High)

Directivity angle of transducer which you use should be input for high and low frequency respectively.

3-2 0093112802-06

Page 55

CVS-128/128B Chapter 3 How to use the menu2

Bubble

Bubble-prevention process can be activated by setting [Weak] or [Strong].

Bubble time set

While auto-range or auto-shift is in use, and if the missing image is caused by bubble, range and shift continues changes until sea bottom is detected by auto mode. Setting the bubble time duration holds the range or shift at the level when bubble started. If bubble disappears and sea bottom is detected, range or shift returns to auto mode. This makes the time shorter until the image comes back to normal. After the specified time, the mode returns to the previous auto-range or auto-shift. (Setting: OFF, 1minutes to 10minutes)

3.4 Setting of Basic Set Item

Temperature Unit

It switches the unit of temperature to ˚C, °F.

Local time Offset

The local time offset can be set by 0.5 hours (30 minutes) unit. (Setting: - 11.0 to 14.0 h) (UTC: 0.0)

GPS select

It selects whether the GPS sensor is the KODEN made one or not.

Caution: Only when connecting the

Koden GPS sensor to the equipment directly, select [KODEN GPS]. When connecting the GPS sensor even Koden one) via Plotter etc to the equipment, select [Other].

GPS initialize

Prev In out Correct Setting Maintain

Language

Range&Speed unit

Depth unit Temperature unit Localtime offset GPS select GPS initialize

Return

English

NM,kn m

°C

0.0 Others No

Language

Switch to the language to be displayed.

Caution: [Language] is displayed in red

characters.

Range & Speed Unit

It switches the display unit to [NM, kn] or [km, km/h].

Depth Unit

It switches the unit of depth to m, fm, l.fm and ft.

It is valid only when KODEN GPS is connected. The GPS sensor is initialized.

Caution: When connecting the GPS

sensor other than KODEN GPS, do not use this item.

3.5 Maintenance Menu

Prev In out Correct Setting Maintain

* For CVS-128B

Simulation Slideshow Initialize System check

ll WPTs:DLT

ll IMG DT:DLT Bottom start Past image* ON

Inner-hull TD select* Return

Simulation

When the [Simulation] is set ON, the pseudo image of echo sounder is displayed.

OFF OFF No

1.5 No

TDM-091D

0093112802-06 3-3

Page 56

Chapter 3 How to use the menu2 CVS-128/128B

Slide show

The slide show of the images stored in [Image] [Image recall] is available. The time intervals for image changeover can be selected from 15 seconds and 30 seconds.

Caution: To perform slide show,

registration in the list of image memory is required. When it is not registered, slide show cannot be selected.

Initialize

It returns all the settings in the menu to the factory settings. However, the memorize d data of display remains unchanged.

Caution: It returns to the factory settings

and the power is automatically shut down.

System Check

It is used for diagnostic test. (See [4.5 Dia

gnostic Test])

All WPTs deletes

All WPT lists can be deleted.

All stored image deletes

All stored image lists can be deleted.

Bottom start

Set up the starting depth of the seabed detection.Once set, the fish echo or the seabed shallower than set up depth will not be detected.

Inner-hull

When the installation of a transducer is [Inner-hull], select the [Yes].

Caution: When a setting is altered, the

value of Gain (TD) will be initialized.

TD select

Choose the installed transducer (TD) in the menu list.

Caution: When transducer is choosen by

model name, [Beam angle] value (directivity angle) is changed automatically depending on the transducer.

For CVS-128B

3.6 Setting of Adjust2 Item

Prev In out Correct Setting Maintain

djust2

STC strength H STC depth H STC strength L STC depth L Color adjust

Image speed adj Bottom limit Return

The visivility of the fish school echo can be adjusted by STC setting.

Adjustment can be done for high-frequency and low-frequency independently.

0.0 50

1.0

Past image

When the [Past image] is set to ON, the gain control is effective for all screens including the past image. When the [Past image] is set to OFF, the gain control is effective for current image only.

For CVS-128B

STC strength adjust Low / High

Set smaller values for higher sensitivity.

STC depth adjust Low / High

Depth limitation of STC adjustment. Unit: Meter

STC can be operated from 0 to the setting depth.

3-4 0093112802-06

Page 57

CVS-128/128B Chapter 3 How to use the menu2

Color adjust

Rainbow pattern of the echo image can be changed.

Set the value of each color in the range from 0 to 99%. Confirm color distribution by the rainbow pattern of the left side of the screen.

Prev In out Correct Setting

Maintain

djust2

EXAMPLE: When the yellow value is change from 60 to 80 in the setting, the Rainbow pattern becomes as shown below.

Red Orange

Yellow

Green Sea green Light blue

Marine blue Return

95 90 60

30 20

EXAMPLE: Displayed 20 m, setting value: 2.0, a bottom can be detected up to approximetery 40m.

Caution: If the setting value is increased,

the image speed becomes slower .

Sounding

Sounding is performed up to the maximum depth set during auto range is in operation. The maximum range is 800 m. At the initial setup, the range is up to 200 m for CVS-128 and up to 500 m for CVS-128B. (Setting: m: 10 to 800, I.fm: 10 to 600, fm: 10 to 400, ft: 10 to 2800)

3.7 Frequency Select

djust

D.range Display1

Display2

larm1

larm2 NAV Image System

Freq* Next

* For CVS-128B

Freq select (L)* Freq select (H)* Power freq adj* Return

42.0

210.0

107.0

Before the change

After the change

Image speed adjust

The image speed can be adjusted. The image speed becomes faster in a minus

direction, and slower in a plus direction.

Caution: Image speed cannot set faster

than the maximam speed value.

Bottom limit

The detection of sea bottom can be changed. Sea bottom can be detected up to the range of

display multiplied by the setting value.

Frequency select (Low / High)

The frequency of the connected transducer (low frequency and high frequency) is chosen.

Caution: Do not choose a frequency

different from the frequency of the connected transducer.

Caution: When the frequency out of the

specified range is choosen, the setting value is displayed in a faded color.

For CVS-128B

0093112802-06 3-5

Page 58

Chapter 3 How to use the menu2 CVS-128/128B

Power frequency adjustment

It is necessary to adjust power frequency when noise appears on the image. The value for adjustment depends on the frequency of the transducer.

Caution: Power frequency adjustment is

for internal noise, so there is no effect for external noise.

For CVS-128B

3-6 0093112802-06

Page 59

CVS-128/128B Chapter 4 Maintenance and Inspection

Chapter 4 Maintenance and Inspection

4.1 Inspection

The daily maintenance and inspection extends the life of equipment. To always keep the equipment in the best condition, implement periodically the inspection shown in the table below.

Item Content of Inspection

Connector at the rear of CVS-128/128B Display unit

Wiring of cables Check the wiring of cables connecting the equipm ent and the

Grounding of display unit Scrape the rust off the ground terminal and make its contact well.

4.2 Cleaning

Check the looseness.

damage of cable.

CVS-128/128B Display unit

Contamination on the screen may cause faint images. For cleaning the screen, wipe the screen with soft and clean cloth dipped with diluted neutral detergent. Pay full attention as the screen is easily getting scratched. No thinner shall be used.

The display unit has a special coating. Do not use a solvent such as

Caution

For cleaning the housing, do not use plastic solvent such as thinner or alcohol. Painting on the surface and characters at the operating portion may melt. After wiping with soft and clean cloth dipped with diluted neutral detergent, wipe away with dry soft and clean cloth.

paint thinner, acetone, alcohol, and benzene, etc. Strong rubbing may cause bruising or scratching.

T ransducer

In case of through-hull equipped transducer, check the surface of opening of transducer (portion from which the ultra-sonic is emitted). If shells and oil are stuck, scrub the surface with a wooden o r bamb oo knife with caution not to damage the surface and remove stuck materials. If you scrub strongly, the surface will be damaged, resulting in deteriorated performance of transducer.

0093112802-06 4-1

Page 60

Chapter 4 Maintenance and Inspection CVS-128/128B



4.3 Fuse Replacement

Warning

If the input voltage is too high, the over-current flows or a trouble occurs inside, the fuse will blow out. The fuse is housed in the power cable.

Use the specified fuse. If you use a fuse other than specified one, it may lead to a serious accident.

4.4 If you suspect a trouble

Symptom Possible cause of trouble Countermeasure

Even if the power is powered on, nothing is displayed.

The unit starts up. But, nothing is displayed on the display.

Too much interference and noise.

The display of water temperature / boat speed is abnormal or not displayed.

The display of present location/course is abnormal or not displayed.

 Blown fuse.  The power voltage is out of

specification (10.8 to 31.2 VDC).

 Poor connection between

power cable and battery.

 Connection between

transducer and display unit.

 Defect of LCD display block.

 Installed position of

transducer.

 Interference from the echo

sounder on other boat.

 Connection of sensor

connector.

 Input source of water

temperature sensor / speed sensor.

 Connection between this unit

and navigation equipment.

Exchange a fuse.(See [4.3 Fuse

Replacement])

 Use a proper power as per

specification.

 Confirm a connection between the

power cable and the battery.

Confirm a connection between

Transducer and Display unit.

 Consult a repair shop or the

distributor in your market.

Confirm the position of transducer.

(See [5.3 Installation of Transducer])

 Apply the interference rejection.

(See [2.3 Rejection of Interference])

Confirm the connection of the sensor

connector.

 Confirm the input source.

Confirm a connection between

Display unit and the navigation equipment.

4-2 0093112802-06

Page 61

CVS-128/128B Chapter 4 Maintenance and Inspection

4.5 Diagnostic Test

Perform the operation diagnosis. To check the operation diagnosis of panel key,

the state of sensor inside and the version of software.

Confirm the version

3 displays the information on the version of

software. When inquiring, inform us of Ver XX.XX. KM-E79 Ver.xx.xx in case of CVS-128 KM-F22 Ver.xx.xx in case of CVS-128B

Return to the menu

Press the [MENU] key for more than 3 seconds.

LCD Test

Diagnose

1 displays the diagnostic result.

The result of ROM and RAM check displays OK when normal and NG when abnormal.

Caution: To test the NMEA, TEMP and SPEED, the special checker is necessary.

2 implements the key input test. When pressing the key, the color of a part corresponding to the pressed key changes.

When pressing the [GAIN (HF)], the LCD test is performed.

0093112802-06 4-3

Page 62

CVS-128/128B Chapter 5 Installation

Chapter 5 Installation

5.1 Items of Caution on Installation

To realize the full performance of echo sounder, the installation of CVS-128/128B must be performed by an engineer who is officially authorized by our company. The installation wo rk include s the following content.

(1) Unpacking the components (2) Inspection of configuration unit, spare, accessories and material for installation (3) Check of power voltage and capacity of current (4) Decision of installing location (5) Installation of Display unit and transducer (6) Installation of accessories (7) Plan and execution of cable laying and connection (8) Adjustment after completion of installation

Unpacking the components

Unpack the components and confirm that all of the items match with the contents on the equipment configuration list. If not matched, contact the dealer you purchased or our sales company.

Inspection of components and accessories

Inspect the appearance of each components and accessori es and check that no dents or damage exist.

If any dents or damage exist and they are believed to be caused by accident during tran sportation, contact the transportation and insurance com pany and consult our sales company or our dealer nearest to you.

Decision of Installing Location

To realize the full performance of equipment, install the equipment, considering the points mentioned below.

(1) Install the equipment at the location in the bridge so that its display can be easily seen. (2) Select a safe location where the equipment is not exposed to humidity, water splash, rain and

direct sunshine.

(3) Keep enough space for maintenance. Especially, secure enough space at the rear panel wh ere

many cables are concentrated.

(4) Keep the equipment as far away from the wireless transmitter/receiver as possible.

The equipment is not waterproof. A void excessively damp pla ce. Do not install the equipment in the place suffering from excessive waterdrops. Otherwise, the corrosion may occur inside.

0093112802-06 5-1

Page 63

Chapter 5 Installation CVS-128/128B

Laying and Connection of Cable

(1) Keep the transducer and power cable as far away from the cables of other electronic equipment

as possible.

(2) The cabinet of Display unit shall be securely grounded to the hull, using the ground terminal on

the rear panel.

Caution: The ground side of power input of this equipment is connected to the ground

terminal. In case of + (positive) ground, it cannot be used. The power may short-circuit.

(3) If you connect the power cable directly to the battery, the interferen ce from other electronic

equipment is not subject to occurrence. (See Fig. 5.1.)

Display unit

Good example

Battery Battery

CVS-128 CVS-128B

Noise

Bad example

Display unit

CVS-128/ CVS-128B

Noise

Fig. 5.1 Connection of Power Line

Confirmation after Installation

Be sure to confirm the following items before starting u p this equipment. The confirmation i s mandatory to operate the equipment normally.

(1) Is the power voltage in the boat within the appropriate voltage range? Is the current capacity

enough?

Voltage Range: 10.8 to 31.2 VDC when measured at the power connector input. (2) Is the electric current capacity sufficient? (Power consumption: 25 W) (3) Is the wiring of transducer cable correct? Is the wiring shorted?

5-2 0093112802-06

Page 64

CVS-128/128B Chapter 5 Installation

5.2 Installation of CVS-128/128B Display unit

CVS-128/128B Display unit can be installed either on desk-top or flush-mounted. Install in the following procedure.

Desk-top Installation

(1) Remove two knob bolts fixing the display unit to the bracket. (2) Remove the display unit from the bracket and place it on the stable flat place. (3) Place the bracket on the position where the display unit will be installed and fix the bracket with five

5 mm screws.

(4) Place the display unit on the installation bracket and fix the display unit with two knob bolts

removed in step 1.

Display unit

Installation bracket

Knob bolts

)

(

Fig. 5.2 Desk-top installation

)

(

)

(

Unit: mm (inch)

0093112802-06 5-3

Page 65

Chapter 5 Installation CVS-128/128B

Caution: When installing on the desktop, the maintenance space shown in the illustration

below is required for cable lay-out, plugging-in/out of connector, fuse replacement and bolt tightening.

Fig. 5.3 Maintenance space

5-4 0093112802-06

Page 66

CVS-128/128B Chapter 5 Installation

Flush-mount Installation

(1) Make a square hole at the location to be installed. (See Fig. 5.5.) (2) Turn counter-clockwise the knob bolt fixing the display unit to the mounting bracket to loosen it,

push the unit to the left side and pull the unit upward. The mounting bracket and knob bolt are not

used. (3) Confirm that the unit matches with the square holes. If not matched, correct the square hole. (4) Remove the front frame of the display unit, pulling it toward you. (See Fig. 5.4.) (5) Connect the connectors for power and transducer to the unit respectively. (6) Install the display unit in the installing location (square hole) and fix it with four tapping screws

(4mm) (M4 or pan-head). (Prep are 4mm screws suitable for thickness of installing location.) (7) Install the front frame removed in step (4).

(

)

Threading hole

Fig. 5.4 Flush-mount Instsllation

Unit:mm (inch)

4-4mm (4-5/32) Hole for screw

Fig. 5.5 Work of fiush-mount instsllation hole

(8 21/32)

R25 (63/

64)

Threading

hole

(8 13/16)

220

224

Unit: mm (inch)

0093112802-06 5-5

Page 67

Chapter 5 Installation CVS-128/128B

5.3 Installation of Transducer

The standard installation of the transducer is shown in figure 5.6.

Figure 5.6 Installation of T r ansducer

In case of Inner-hull

Using the optional inner-hull kit (MFB-04), install the transducer to the inner side of ship’s bottom.

Caution on installation

(1) Select the location where no bubble is generated during navigation.

(2) Select the relatively thin location of ship’s bottom.

(3) Be sure to remove oil on the contact surface. File the contact surface with sand paper (#400) so that the adhesive strength will increase.

(4) The adhered surface will dry in about two hours.

(5) Leave the unit for a whole day and fill in the coolant. More than 80 % of the transducer should be submerged in the coolant.

Figure 5.7 Inner-Hull installation

Caution: It is strongly recommended to confirm the location of the installation of Inner-hull

with the ship manufacturer. The Inner-hull device is more simplified method. The gain falls dramatically in comparison with the Through -hull performance. Low frequency (50 kHz) may not be used due to large signal attenuation in some cases. Depth range performance using 200 kHz Transducer in case of Inner-hull can be less about 50% than that of Through-hull.

Caution: Fishing boats may have structure with FRP contained air bubbles and foamed

materials that would prevent ultrasound from penetration. Therefore, the location convenient for installation may not be locations where attenuation of ultrasound is low enough.

5-6 0093112802-06

Page 68

CVS-128/128B Chapter 5 Installation

In case of Through hull

Install the transducer directly to the ship’s bottom

Installation Procedure

(1) Select the installing location. (2) Remove the fixing nut and one piece of rubber packing. (3) If the slope of ship’s bottom is greater than 5°, make a wooden base to fit to the slope of ship’s

bottom. To reduce the water resista nce, cut the b ow direction tip of wooden base at the outer side

of ship’s bottom in the triangle shape. (4) Make holes at the installing location. If the wooden base is used, make holes in the wooden base. (5) Thread the rubber packing in the transducer and then the cable. (6) To prevent water from seeping through the gap between the transducer and the hole, fill out the

gap with FRP or silicon glue. (Glue the wooden base likewise.) (7) Thread the rubber packing and fix it with the fixing nut firmly. (8) Connect the transducer cable to the connector of Display unit.

Fixing nut

Rubber packing

In case that the slope of ship

Rubber packing

Ship,s bottom

Transduce

Less than 5

s bottom is less than 5

Figure 5.8 Through-hull Installation

Fixing nut

Wooden base

Rubber packing

Transduce

In case that the slope of ship,s bottom is greater than 5

Rubber packing

Wooden base

s bottom

Ship

0093112802-06 5-7

Page 69

Chapter 5 Installation CVS-128/128B

5.4 Wiring

Connection of Cable to CVS-128/128B Display unit

Connect the power cable and transducer to the connectors of CVS-128/128B Display unit.

・Power input

10.8 to 31.2VDC

・NMEA data input output

GPS, plotter etc

・Sona-Tone

Line output for speaker with amplifier

・Power output

For power of GPS etc

・Transducer

For 50/200kHz in common

・Speed sensor data input ・Water temperature sensor data input

output

Pin Assignment of Rear Connector

Pin assignment viewed from the rear of Display unit.

POWER

Caution: Do not connect each wire to ship’s earth.

Sona-ToneTM R Sona-ToneTM L Power + Outside power (-) NMEA TX-

NME NME NME Power Shield Sona-Tone Outside power (+)

X+

RX-

COM

・External monitor

nalog RGB

Speed sensor input Speed sensor power (+) Transducer input output Transducer shield Transducer input output Water temperature sensor power Water temperature sensor input Speed sensor power (-)

R-GND G G-GND B B-GND H-SYNC V-SYNC Un-connected Un-connected

5-8 0093112802-06

Page 70

CVS-128/128B Chapter 5 Installation

Connection of Power Cable

Connect the power cable to the [POWER] connector and the transducer to the [J6] at the rear of Display unit connector.

Connection of DC power cable (CW-264A-2M)

To [POWER] connector

Caution: Wind the insulation tape around th e un-used lead wire for core- wires not to contact

each other.

3.5 stereo jack

DC+ (Red) DC- (Black)

Grounding

 Use heavy gauge cable for grounding wire.  Connect the grounding wire to the grounding material in a short distance.  When connecting the external equipment of which positive polarity is conne cted to the ground line,

do not connect the ground of signal line to the cabinet ground.

0093112802-06 5-9

Page 71

Chapter 5 Installation CVS-128/128B

Connection of Transducer

At the end to the transmission/receiving cable for TD-500T -2B, TD-500T-3B, TD-501T -3B, TDM-07 1 and TDM-091D a water proof connector with 8-core is provided.

At the end to the transducer for TD-501C is plain.

1) TD-500T-2B/500T-3B/501T-3B/TDM-071/TDM-091D

Connect to the J6 connector on the back of the receiver display unit.

2) TD-501C

The user must have the cable, CW-840-0.3M for the transducer.

Solder the transducer to CW-840-0.3M while referring to the table on connecting transduce rs. After soldering is completed, please be sure to add water-resistance and insulation by applying

electrical tape (or other such t ape) onto the soldered part of the cable.

Transducer Connection Table

Transducer Cable Transducer

2 lead shield wire number 2 lead shield wire color TD-501C

3 orange black 4 shield shield 5 white white

CW-840-0.3M

2 lead shield

3 TD1 (orange)

Shield

5 TD2 (white)

To Transducer

Lead wires

1 SPD.PULSE (blue) 2 SPD.VCC (violet)

8 SPD.GND (black)

6 TEMP.VCC (green) 7 TEMP.SIG (red)

To Speed Sensor

To Temperature Sensor

Caution: Wind the insulation tape around th e un-used lead wire for core- wires not to contact

each other.

5-10 0093112802-06

Page 72

CVS-128/128B Chapter 5 Installation

Connection with external equipment

The DC power cable contains the connection cables for external equipment such as navigation equipment and KODEN GPS sensor.

Color Pin Remark

Red 3 Power +

Black 9 Power -

Orange 6 NMEA TX +

Blue 5 NMEA TX -

White 7 NMEA RX +

Green 8 NMEA RX -

Color Pin Remark

White 2

Red 1

Black 11

Yellow 12 Outside power (+)

Gray 4 Outside power (-)

Shield 10

Sona-Tone External speaker output (with ø3.5 stereo jack)

Connection with GPS-20A

After soldering, implement the waterproof and insulation treatment on the connected part with the self-melting tape.

Color Remark Color

Orange

CVS-128/128B

DC power cable

(CW-264A-2M)

NMEA TX +

GPS-20A (No Type)

Connecting up without using a

connector

Orange

GPS-20A (Type B)

Connecting up using a

connector*

Blue

White Green Yellow Outside power (+) Red

Gray

NMEA TX NMEA RX + NMEA RX -

Outside power (-)

Blue

White

Green

Black

3 4 5 6 1

*Optional connector (LTWBD-06PMMP-LC) is necessary.

0093112802-06 5-11

Page 73

Chapter 5 Installation CVS-128/128B

Connection with Speed Sensor or Water Temperature Sensor (Option)

When installing the optional speed sensor or water temperature sensor, connect to the [J6] connector together with the transducer via the transducer cable (Type: CW-840-0.3M). For wiring, see the figure below.

After soldering, implement the waterproof and insulation treatment on the connected part with the self-melting tape.

Structure of Transducer Cable

2 core shield wire

lead wire

TD1 (Orange)

Shield

TD2 (White)

SPD.PULSE (Blue) SPD.VCC (Violet)

SPD.GND (Black)

TEMP.VCC (Green)

TEMP.SIG (Red)

To Transducer

To the speed sensor

To the water temperature sensor

Caution: Wind the insulation tape around th e un-used lead wire for core- wires not to contact

each other.

Connection Table of Transducer

Transducer Cable Transducer

No. of 2 core shield Color of 2 core shield TD-500T-2B

TD-500T-3B

TD-501T-3B

TD-501C

3 Orange Red Black 4 Shield Shield Shield 5 White White White

Connection Table of Speed Sensor and Water Temperature Sensor

Transducer Cable Water Temperature Sensor / Speed Sensor

No. of lead

wire

1 Blue — Green Green Green 2 Violet — Red Red Red 6 Green Gray White White White 7 Red Gray Brown Brown Brown 8 Black — Shield Shield Shield

Caution: No.8, SPD.GND (Black), only use for speed sensor.

Do not connect with other grounding wire.

5-12 0093112802-06

Color of lead

wire

T-81 ST-80

ST-80-1

ST-90-1

ST-90

ST-100

ST-100-1

Page 74

CVS-128/128B Chapter 5 Installation

Connection of External Speaker for Sona-ToneTM (Prepared by a customer)

The ø3.5 stereo jack is provided to the power cable. If you connect the speaker with the amplifier to the external, you can clearly hear the Sona-Tone sound. Adjust the volume of speaker with the amplifier equipped to the speaker

3.5 stereo jack

Connection of External Monitor (J7) (Prepared by a customer)

When installing an external monitor (VGA monitor, analog RGB input), connect it via CW-576-0.5M. For its wiring, refer to the illustration below.

Structure of CW-576-0.5M

Nonuse

0093112802-06 5-13

Page 75

Chapter 5 Installation CVS-128/128B

5.5 Serial Data

Input Data

The sentences of GGA, GLL, HDT, MTV, MWV, RMC, VHW, VTG and ZDA can be received. The type of NMEA0183 Ver.1.5, Ver.2.0 and Ver.3.0 can be input.

Information Priority Order of Sentence Information Priority Order of Sentence Latitude,

Longitude Course VTG > RMC Wind Speed MWV Heading HDT Date ZDA > RMC Ground Spee d VTG > RMC Time ZDA > GGA Water Speed VHW Water

Output Data

The sentences of DBT, DPT, GGA, GLL, HDT, MTW, MWV, RMC, TLL, VHW, VTG and ZDA can be transmitted. The output is performed in the type of NMEA0183 Ver.2.0. However, the DBT is performed in Ver.1.5.

GGA > RMC > GLL Wind Direction MWV

MTW

Temperature

Sentence Information Sentence Information DBT Depth MWV Wind Direction, Wind Speed DPT Depth from the transducer RMC Latitude/Longitude, Course,

Ground Speed, Date GGA Latitude/Longitude, Time TLL Target Position GLL Latitude/Longitude VHW Water Speed HDT Heading VTG Course, Ground Speed MTW Water Temperature ZDA Date,Time

5-14 0093112802-06

Page 76

CVS-128/128B Chapter 6 Table Attached

Chapter 6 Table Attached

6.1 Menu List

The factory set value is shown by the bold and underline.

[Disp] key

【▲RANGE▼】key

[GAIN(HF) ], [GAIN(LF) ]

Disp

RANGE

Gain selec

Auto adjust

Gain

NAV1, Normal (H), Zoom (H), Dual freq, Zoom (L), Normal (L), NAV2

Auto range, 5.0, 10.0, 20.0, 50.0, 100, 160, 300, 500, Auto shift

Manual, Cruising, Fishing

- 30 to 10 (H): 0, (L): 0

0.0 to 10.0 (H): 6.0, (L): 6.0

[BRILL] key

[EVENT] ke

[F1] ke

[F2] key

LCD brill

Panel brill

1 to 10: 10

Store pos, Store image, Fishing hot spot

Image speed, IR, Color rejection, Noise rejection, Shift, Zoom range,

Zoom start, A scope, White line, Background color, Disp width,

NAV start, NAV1, NAV2, Image swap, Image recall, Sona-tone

Image speed, IR, Color rejection, Noise rejection, Shift, Zoom range,

Zoom start, A scope, White line, Background color, Disp width,

NAV start, NAV1, NAV2, Image swap, Image recall, Sona-tone

0093112802-06 6-1

Page 77

Chapter 6 Table Attached CVS-128/128B

[MENU] key

djus

Image speed (Speed1, Speed2, Speed3, Speed4, Stop, Speed5 (1/1), Speed6, Speed7,

Speed8, Speed9)

IR (OFF, Weak, Strong : Strong (For CVS-128) , Weak (For CVS-128B))

Color rejection (0 to 50 %: 0%)

Noise rejection (0 to 10: 0)

TVG (Weak, Medium, Strong)

TX power (20, 30, 40, 50, 60, 70, 80, 90, 100, Auto)

D.range

Display1

Display2

Gain (TD) (-50 to 50)

Inner-hull : No

H: 0, L: 0

Inner-hull : Yes

H: 15, L: 30

Pulse width (Super short, Short, Middle, Long) (For CVS-128B) Band width (Super narrow, Narrow, Middle) (For CVS-128B)

D.Range (12dB to 30dB: 24dB) (For CVS-128B)

Shift step (1m, 10m, 1/8, 1/4)

Zoom type (Bottom, Bottom Discrimination, Zoom, Bottom Zoom, Bottom Follow Zoom)

Zoom range (2.5 to 200 m: 10.0 m)

Zoom start (0 to 800 m: 0m)

Disp width (Left2, Left1, Center, Right1, Right2)

Range prese

Inner-hull : No

Range 1 (2.5 to 1200 m: 5.0)

Range 2 (2.5 to 1200 m: 10.0)

Range 3 (2.5 to 1200 m: 20.0)

Range 4 (2.5 to 1200 m: 50.0)

Range 5 (2.5 to 1200 m: 100)

Range 6 (2.5 to 1200 m: 160)

Range 7 (2.5 to 1200 m: 300)

Range 8 (2.5 to 1200 m: 500)

Inner-hull : Yes

Range 1 (2.5 to 1200 m: 5.0)

Range 2 (2.5 to 1200 m: 10.0)

Range 3 (2.5 to 1200 m: 20.0)

Range 4 (2.5 to 1200 m: 50.0)

Range 5 (2.5 to 1200 m: 80)

Range 6 (2.5 to 1200 m: 100)

Range 7 (2.5 to 1200 m: 160)

Range 8 (2.5 to 1200 m: 200)

A scope (OFF, ON)

White line (OFF, 1, 2, 3, 4, 5, Auto)

Background color (Pale blue, Marine blue, Blue, Dark blue, Black, Darkkhaki,

Mediumseagreen, Light grey, White, Night mode)

Color tone (Monochrome, 8 color, 16 color, 64 color)

Depth value (OFF, Small, Middle, Large) Unit display (OFF, ON) Water temp graph (OFF, ON)

Fish symbol (OFF, Symbol 1 to Symbol 10)

Symbol info (OFF, Depth, Size, Bottom<=>Fish)

Detection area (OFF, ON)

Scale display (OFF, One, All)

Scale (Small, Middle, Large) Image direction (←|← , →|→ , ←|→)

Bottom detection (Auto, High frequency, Low frequency)

Color table1 (Header information, Header BG color, VRM, Depth, Scale,

Scale line,Detection area H, Detection area L)

Color table2 (Symbol info, Menu BG color, Big fish color, Bottom color)

Scale type (0, 1)

Big fish (20 to 90: 50)

Freq display (OFF, ON) (For CVS-128B)

6-2 0093112802-06

Page 78

CVS-128/128B Chapter 6 Table Attached

Alarm 1

Alarm 2

Image

System

Freq

Bottom alarm (OFF, ON)

Upper depth (0 to 800 m: 5 m)

Lower depth (1 to 800 m: 50 m)

Fish alarm (OFF, ON)

Position (0 to 800 m: 5 m) Range (1 to 800 m: 50 m)

Level (Weak, Medium, Strong)

Water temp alarm (OFF, ON (Inside), ON (Outside))

Upper temp alarm (- 5 to 45.0 °C: 20.0 °C)

Lower temp alarm (- 5 to 45.0 °C: 15.0 °C)

Speed alarm (OFF, ON (Upper), ON (Lower))

Speed limit (0 to 80 kn: 0 kn)

Arrival alarm (OFF, ON)

XTE alarm (OFF, ON)

NAV alarm range (5 to 999 m: 10 m)

NAV start (No.1 to No.10)

NAV cancel (Yes, No) WPT edit (No.1 to No.10)

WPT delete (No.1 to No.10)

Background color (OFF, White, Black)

NAV 1 (Normal (H), Zoom (H), Dual freq, Zoom (L), Normal (L))

NAV 2 (Normal (H), Zoom (H), Dual freq, Zoom (L), Normal (L))

Image swap (A|B, B|A)

Image recall (No.1 to No.10)

Image comment (No.1 to No.10)

Image delete (No.1 to No.10)

Image partition ( , )

Fish image (A|B, A| , |B)

EVENT key set (Store pos, Store image, Fishing hot spot)

F1 key set (Image speed, IR, Color rejection, Noise rejection, Shift, Zoom range,

Zoom start, A scope, White line, Background color, Disp width,

NAV start, NAV 1, NAV 2, Image swap, Image recall, Sona-ton)

F2 key set (Image speed, IR, Color rejection, Noise rejection, Shift, Zoom range,

Zoom start, A scope, White line, Background color, Disp width,

NAV start, NAV 1, NAV 2, Image swap, Image recall, Sona-tone)

Operation guide (OFF, ON)

Sona-tone (OFF, ON)

Key loc

Freq select (L) (24.0 to 210.0 kHz : 42.0) (For CVS-128B) Freq select (H) (24.0 to 210.0 kHz : 210.0) (For CVS-128B)

Power freq adj (100.0 to 130.0 : 107.0) (For CVS-128B)

0093112802-06 6-3

Page 79

Chapter 6 Table Attached CVS-128/128B

In ou

Correct

Setting

Maintain

Adjust2

Buzzer setting (OFF, ON)

Temp source: (InsideSensor, NMEA)

Speed source (InsideSensor, NMEA)

Baud rate (4800, 9600, 19200, 38400)

NMEA monitor (OFF, ON)

NMEA output data (ON : DBT, DPT, TLL OFF : GGA, MTW, VHW, VTG, ZDA)

NMEA output data (ON : None OFF : GLL, HDT, MWV, RMC)

Draft set (- 10.0 to 10.0 m: 0.0 m)

Sonic speed (Seawater, Freshwater)

Water temp (- 10.0 to 10.0 °C: 0.0 °C)

Boat speed (- 50.0 to 50.0 %: 0%) Beam angle H (1 to 120: 17°) Beam angle L (1 to 120: 50°)

Size adjust (1 to 10: 6)

Detect adjust f (1 to 6: 4)

Bubble (OFF, Weak, Strong) Bubble time set (OFF, 1 to 10minutes: 5minutes)

Language (English, Japanese, etc)

Range&Speed unit (NM, kn, km, km/h)

Depth unit (m, fm, I.fm, ft)

Temperature unit (°C, °F)

Localtime offset (- 11.0 to 14.0: 0.0)

GPS select (Others, KODEN GPS)

GPS initialize (No, Yes)

Simulation (OFF, ON)

Slideshow (OFF, 15, 30)

Initialize (No, Yes)

System chec

All WPTs: DLT (No, Yes)

All IMG DT: DLT (No, Yes)

Bottom start (0.0 to 20.0: 1.5) Past image (OFF, ON) (For CVS-128B)

Inner-hull (No, Yes) TD select (TDM-071, TDM-091D, Others TD) (For CVS-128B)

STC strength H (-10.0 to 10.0: 0.0)

STC depth H (2 to 1000: 40)

STC strength L (-10.0 to 10.0: 0.0)

STC depth L (2 to 1000: 40)

Color adjust (Red:90,Orange:78,Yellow:66,Green:53,Sea green:39,Light blue:25,

Marine blue:12)

Image speed adj (-10 to 10: 0)

Bottom limit (1.0 to 3.0: 1.0)

Sounding (10 to 800m: 200m(For CVS-128), 500m(For CVS-128B))

6-4 0093112802-06

Page 80

CVS-128/128B Chapter 6 Table Attached

6.2 Specification

0093112802-06 6-5

Page 81

Chapter 6 Table Attached CVS-128/128B

6-6 0093112802-06

Page 82

CVS-128/128B Chapter 6 Table Attached

6.3 Appearance

Plane view

0093112802-06 6-7

Page 83

Chapter 6 Table Attached CVS-128/128B

Dimension drawing of table installation

Hole for installing 4-4mm screw

240

(9 29/64)

220

(8 21/32)

(

)

Threading hole

224

(8 5/32)

(8 13/16)

Unit: mm (inch)

Dimension drawing of flush-mount installation

6-8 0093112802-06

Page 84

Koden CVS-128, CVS-128B Operation Manual

Specifications and Main Features

Frequently Asked Questions

User Manual