Koden CVG-200 Operation Manual

Download

Page 1

Page 2

Declaration of Conformity

(As required by Article 7 (1) of Directive 89/336/EEC)

Declares under his sole responsibility that the produced Plotter/Sounder manufactured by

Koden Electronics Co., Ltd.

5278 Uenohara,

Uenohara Citv,

Yamanashi-Ken

409-0112, Japan

Telephone +81 554 20 5865 Telefax +81 554 20 5880

Identified by the type number CVG-200 to which this declaration refers conforms to the

requirements of Directive 89/336/EEC amended by 92/31/EEC and 93/68/EEC and is in

conformity with the EMC, Health and Safety standards of

EN60945

Signed …………………………………….. Heinz Hoghoff,

Dated 06 April 2005 Koden Elektronik GmbH. Am Gewerbepark 15 D-64823, Gross–Umstadt Germany. Phone +49 6078 2056 Telefax +49 6078 73824

N.B. As this product is for Maritime use compliance with Directive 72/23/EEC is not required.

Page 3

CVG-200 OPERATION MANUAL

Doc No: 0093132802

Amendment History

Document No ＆Rev

No.

0 93132802-00 05/01/24 First issue 1 93132802-01 05/03/24 2 0093132802-02 05/12/01 Chapter 6 Annex (It is compatible from Ver2.01.) 3 0093132802-03 06/08/16 Chapter 2 4 5 6 7 8

No.

Amendment Policy

When any change is applied in the document, only the document numbers of the relevant sheet(s)

Date Amendments

Chapter 5 Chapter 6 (93132810→93132802)

and cover sheet are modified. The rest of the sheets are not changed. The document number is shown in the footer area, either in the right or left of each sheet.

No part of this publication may be reproduced, transmitted, translated, in any form by any means without the written permission of Koden Electronics Co. Ltd. The technical descriptions contained in this publication are subject to change without notice. KODEN assumes no responsibility for any errors, incidentals or consequential damages caused by misinterpretation of the descriptions contained in this publication.

Page 4

CVG-200 Preface

Getting St arted

Using the Main

Text

Please guard against losing or damaging this text. In the event of reselling or handing over this device to someone else, please be sure to include this manual to the new owner. In addition, it is advisable to have this text nearby while this device is in operation.

Important Safety Items

Symbols used in this manual

The following symbols are used in this manual. You are requested to be fully aware of the meaning of each symbol before carrying out inspection and maintenance of this equipment.

Warning mark

Operating this equipment while ignoring this sign may lead to

Alarm

physical injury or damage to the equipment.

Caution mark

Caution

High Voltage mark

Prohibition mark

Operating this equipment while ignoring this sign may lead to a malfunctioning of the equipment.

Operating this equipment while ignoring this sign may lead to electrical shock.

This sign indicates that a specified action is prohibited. The prohibited action will be shown in the vicinity of the mark.

93132801-00 (1)

Page 5

Preface CVG-200

Types of Operational Warnings

Warning

Caution

This device aids in navigation. For decision making in sound navigation, please be sure to use other widely used resources in addition to this device: land maps, sea maps, GPS devices, landmarks, water depth, obstacles, and other devices.

This devices uses voltage levels which are potentially life threatening. Even if the power is shut-off, live electricity may remain within the circuits. Warning labels and protective covers have been added to prevent carelessly touching high-voltage circuits. For the sake of safety, switch off the power before performing any inspection of the inside of this device. Then, please proceed to properly discharge any remaining voltage from the condenser. Proper inspection must be carried out by a qualified technician.

This GPS (Global Positioning System) functions using 28 satellites. Should there be no obstacles, and should the sky be clear, the user should be able to find his position anywhere in the world. However, this group of satellites are operated and managed by the US Pentagon, and we have no control over the quality of reception or the policy of the US government. Without prior notice, the accuracy of position, bearings, speed measurements may deteriorate, or, adjustments, testing, and course corrections, etc. may be necessary. Signals from the satellites may be disrupted at certain times.

(2) 93132801-00

Page 6

CVG-200 Preface

Types of Cautions During Maintenance

Caution

Warning

z Be certain to turn off your boat’s power

Carelessly switching on the power during inspection may result in electrical shock. In order to prevent such accidents, be sure to switch off the power of this device as well as the power of the boat. Furthermore, a warning sign saying “In operation” closely placed to the power switch can also help ensure safety.

z Warning of Remaining High Voltage

Regarding transmitting circuits using the condenser, high voltage may remain in the circuit for a few minutes after switching the power off. When inspecting a part of the device with this mark, be sure to wait a few minutes after the power has been switched off. Also, be sure to properly discharge any remaining voltage.

z Dust Caution

Dust can induce injury to the lungs. When cleaning the inside of this device, be careful not to breathe in dust. Please use a safety mask or other equipment to ensure your safety.

Caution

z Countermeasures towards Static Electricity

The flooring of the boat can cause static electricity when in contact with carpet or synthetic clothing fibers. This static electricity can in turn destroy electronics. Install proper countermeasures towards static electricity to protect your equipment.

93132801-00 (3)

Page 7

Preface CVG-200

How to use this manual

Scope of this manual

This manual contains general information as well as system composition, installation, operation and maintenance of the CVG-200 Plotter/Sounder

Structure of this manual

This manual is divided into sections according to the contents as outlined below. This allows for the overview of the entire manual as well accessing detailed information for your specific requirement.

Chapter 1: General Information

- About the GPS

- Applicable Standards

- Software Type Name

- Equipment Configuration

Chapter 2: Equipment Composition

- Standard Equipment List

- Spare Parts List

- Optional Items List

- Available Tra nsducers List

- Transducers

Chapter 3: Specifications

- Specifications

- Serial Data

- Power Requirements

- Environmental Conditions

- External Dimensions and Weight

Chapter 4: Installation

- Installation Consideration

- Unpacki ng of The System

- Inspection of the equipment

- Proper Location for Setup

(4) 93132801-00

Page 8

CVG-200 Preface

- Cable Routing and Connections

- Display Installation

- Internal Connections of The System

- Post-installation Inspections

Chapter 5: Basic Operations

- Name and Function of Parts

- Displaying the Images

- Plotter Screen

- Operation of Sounder Display

Chapter 6: Using the Menu

- Menu Functions

- Sounder Menu

- Plotter Menu

- Setting of other Menus (ETC)

Chapter 7: Trouble Shooting and Maintenance

- Information Required for Service

- Trouble Shooting

- Setting the Bottom Detection Threshold

Chapter 8: Maintenance

- Periodical Inspection and Cleaning

Chapter 9: Technical Reference

- Details of Input Serial Data Sentence

- Details of Output Serial Data Sentence

- Connecting to An External Sounde r

- Connecting to Water Temperature/Speed Sensor

- Serial Data Input/Output

- Data input/output serial line

- Signal Output for External Buzzer

Annex Sheets:

- Menu T ree

- LOLAN C CHAINS

- DECCA CHAINS

93132801-00 (5)

Page 9

CVG-200 Chapter 1

General Information

Chapter 1

General Information

Page No.

1.1 About GPS..................................................................................................1-1

1.1.1 GPS Satellite Arrangement...................................................................................1-1

1.1.2 GPS Organization

1.1.3 On Proper Use

1.2 Outline of The Equipment.........................................................................1-2

1.3 Applicable Standards................................................................................1-2

1.4 Software Type Name ..................................................................................1-2

1.5 Equipment Composition...........................................................................1-2

..............................................................................................1-1

..................................................................................................1-1

93132801-00 Contents

Page 10

CVG-200 Chapter 1

General Information

Chapter 1 General Information

1.1 About GPS

1.1.1 GPS Satellite Arrangement

GPS (Global Positioning System) is a navigation system using 24 satellites (21 plus 3 in service) orbiting above the earth once every 11 hours 58 minutes at an altitude of about 20,000 km.

1.1.2 GPS Organization

Your position is determined by calculating the distance from more than three satellites to your position. Your position (latitude, longitude and altitude) is determined at the intersection point of four spheres formed by four satellites.

Note: The GPS system is based on a geodetic system called the WGS (World Geodetic System). In a conventional world map, one coordinate system differs from others by region. This causes the position fix made on the map and GPS measurement to differ to a certain extent .

1.1.3 On Proper Use

In the following circumstances, your GPS receiver takes more time to fix your position:

・When you first turn on the GPS receiver. ・After having the unit turned for a long time, the previously stored orbital data is not suitable for the

current satellite. ・When you turn the power back on after having not used it over a long distance. The GPS navigation device, within a useful locality, through available data from orbiting satellites, will record and speed your position data to you. When the GPS receiver is first turned on, it starts to store the orbital data sent from the satellite. The first data becomes available after about 15 minutes. After this, the receiver can fix your position within a minute by using the previously stored data. In the case of abnormal or adverse conditions, or if foreign substance enter the device, turn off the power immediately, and contact your nearest sales or service store.

93132801-00 1- 1

Page 11

Chapter 1 CVG-200

General Information

1.2 Outline of The Equipment

The CVG-200 is a plotter/sounder device, consists of a plotter unit with a GPS sensor and a sounder equipped with transmission/receiver.

The available power output is two kinds, 600W and 1kW. It carries two frequencies, 50 kHz and 200 kHz.

1.3 Applicable Standard

The CVG-200 is designed and tested to comply with the international standard of IEC60945 (3rd edition) that defines general requirements of electronic maritime equipment.

1.4 Software Type Name

The following software type is used in the CVG-200.

Software type Application

KMC－92 KM－D91

System control

Echo Sounder system control

1.5 Equipment Composition

The equipment composition of CVG-200 is shown in Figure 1.1.

1-2 93132801-00

Page 12

CVG-200 Chapter 1

General Information

・C-map

Map card

・・User c-card

2MB

・Sounder

・GPS Sensor

GPS-20A

・DGPS Sensor

KBG-2

This cable is included.

Receiver unit

CVG-200

Junction box

JB-10

Junction box

JB-10 JB-12

・NMEA-0183 CH1

Navigator, Sounder, Radar, Autopilot

・NMEA-0183 CH2

Navigator, Sounder, Radar, Autopilot

External VGA monitor

(Analog RGB)

DC Power cable

CW-253-2M

Fuse10A

・Rectifier

VV-2D8-3M

100/115VAC 200/230VAC

PS-006

10.8～

31.2VDC

This cable is included.

External buzzer

CW-838-0.5M

Cable gland

Ship side

Metal

fittings

・Water temperature/

speed sensor

ST-80-1

Water temperature senso

・Transducer

TD-501C

・Transducer

500T-2B /500T-3B /501T-3B

：Standard ：Option ：User Interface

Figure 1.1 Configuration of CVG-200

93132801-00 1- 3

Page 13

CVG-200 Chapter 2

Equipment Composition

Chapter 2

Equipment Composition

Page No.

2.1 Standard Equipment List.............................................................................2-1

2.2 Spare Parts List............................................................................................2-1

2.3 Option Items List..........................................................................................2-1

2.4 Transducers..................................................................................................2-2

93132801-00 Contents

Page 14

CVG-200 Chapter 2

Equipment Composition

Chapter 2 Equipment Composition

2.1 Standard Equipment List

No Item name Type name Remarks 1 Receiver unit CVG-200 With base mount and

Weight/ Length

6.8 kg 1

hard cover

2 DC Power cable CW-253-2M For Receiver unit 2 m 1 3 Transducer Detail in 2.4

Transducer

4 Cable

CW-840-0.3M ( for TD-501C ) 1

for transducer 5 Spare parts SP-101 (2.2 Refer to Sp are parts list) 1set 6 Operation manual English 1

2.2 Spare Parts List

No Item name Type name Remarks Weight/

Length

１

Fuse F-7161-10A

/N30C-125V

For Receiver unit

Q’ty

Q’ty １

2.3 Option Items List

No Item name Type name Remarks 1 Water temperature/

Speed sensor

ST-80-1 Transom (Plastic, with cable) ST-90-1 Inner hull (Plastic, with cable) ST-100-1 Through hull (Bronze, with

cable)

2 Water temperature

T-81with cable Inner hull (Plastic, with cable) 0.2Kg

sensor

3 DGPS sensor KBG-2 For DGPS positioning

Power ＆ Signal cable with

4 GPS sensor GPS-20A-10M-3

5 6

GPS antenna holder Water thermometer scupper

RAH-29 Ratchet mount

MFB-11

connector For GPS positioning Power ＆ Signal cable with connector

Water temperature sensor T-81with cable

7 Inner hull kit MFB-04 Hard vinyl chloride,

applicable to 600W only

8 Inner hull kit MFB-04W Resin, 1KW only 1.5kg 9 Kingston kit MFB-05W Applicable to 1KW only 0.83kg

10 AC/DC Rectifier PS-006 With 2 pcs of 10A fuse

attached

11 AC Power

cable

Junction box (For navigator unit)

VV-2D8-3M Both ends fly lead

(for power supply)

JB-10

1input, 3output ×2circuits

JB-12 1input, 3output, 3 input,

1output

13 Connecting

cable

CW-373-5M 6 pin waterproof connectors

（LTW）both ends

Weight/ Length

0.3 Kg・9m

0.6 Kg・9m

1.2 Kg・9m

1.6Kg 10m

250g 10m

1.2kg

8.0kg 3m

0.4kg 12

0.42kg 5m

0093132802-03 2-1

Page 15

Chapter 2 CVG-200

Equipment Composition

No Item name Type name Remarks Weight/

Length

13 Connecting

cable

14 Connector

(female)

15 Cable gland

16 Metal fittings SL-2 17 Operation

manual

CW-374-5M 6 pin connector/6 pin waterproof CW-376-5M Fly leads/6 pin waterproof CW-381-5M Half-pitched/6 pin waterproof CW-154A-5M 6 pin connector (Nisshin)/Fly LTWBD-06BFFA-L1

80 LTWBD-07BFFA-L1

80 LTWBD-08BFFA-L1

LTWBU-12BFFA-L1 80

CG－1 CG－3 CG－１6 CG－１9

CVG-200. O/M.E

connector (LTW) connector (LTW) connector (LTW) leads

6 pin waterproof connector (LTW) for NMEA0183 7 pin waterproof connector (LTW) (For external sounder) 8 pin waterproof connector (LTW) (For water temperature and speed sensor)

12 pin waterproof connector (LTW) (For external monitor) For steel hull 1.5kg

For wooden hull 2.5kg For FRP hull 0.9kg For FRP /wooden hull 1.0kg Stainless,１ 1/2 inch English

5m 5m 5m 5m

2.5kg

2.4 Transducers

Output Type name Frequency Weight

TD-500T-2B 50/200 kHz 0.7kg

600W

１kW

TD-500T-3B 50/200 kHz 1.5kg TD-501C 50/200 kHz 4.2kg TD-501T-3B 50/200 kHz 3.4kg

2-2 0093132802-03

Page 16

CVG-200 Chapter 3

Specifications

Chapter 3

Specifications

Page No.

3.1 Specifications..............................................................................................3-1

3.1.1General Specifications....................................................................................................3-1

3.1.2 Specifications of Sounder..............................................................................................3-1

3.1.3 Specifications of Plotter

3.2 Serial Data....................................................................................................3-3

3.3 Power Requirements...................................................................................3-4

3.4 Environmental Conditions..........................................................................3-4

3.5 External Dimensions and Weight...............................................................3-4

...............................................................................3-3

93132801-00 Contents

Page 17

CVG-200 Chapter 3

Specifications

Chapter 3

Specifications

3.1 Specifications

Specifications are subject to cha nge without notice.

3.1.1General Specifications

Display 10.4 inch color TFT LCD(480 x 640 dot s) Display mode Plotter

Echo Sounder (Single frequency normal image/Single frequency normal/zoom images/Dual frequency dual images) Plotter + Echo Sounder: Dual screen (Vertical split/Horizontal split) Compass Highway

3.1.2 Specifications of Sounder

TX frequency 50 kHz/200kHz Output power 600W, 1kW Sounding range Select either Auto range or 8 range scales from the scaling group listed to the right.

Zoom range Select 1 range scale from the scaling group listed to the right.

(meter / Japanese fathom / fathom / Italian fathom) 5, 7.5, 10, 15, 20, 25, 30, 35, 40, 45, 50, 55, 60, 65, 70, 75, 80, 85, 90, 95, 100, 110, 120, 130, 140, 150, 160, 170, 180, 190, 200, 210, 220, 230, 240, 250, 260, 270, 280, 290, 300, 310, 320, 330, 340, 350, 360, 370, 380, 390, 400, 450, 500, 550, 600, 650, 700, 750, 800, 850, 900, 950, 1000, 1100, 1200 (feet) 15, 20, 30, 40, 50, 60, 80, 100, 120, 140, 180, 200, 220, 240, 260, 280, 300, 320, 340, 360, 380, 400, 440, 480, 520, 560, 600, 640, 680, 720, 760, 800, 840, 880, 920, 960, 1000, 1040, 1080, 1120, 1160, 1200, 1240, 1280, 1320, 1360, 1400, 1440, 1480, 1520, 1560, 1600, 1800, 2000, 2200, 2400, 2600, 2800, 3000, 3200, 3400, 3600, 3800, 4000 (meter / Japanese fathom / fathom / Italian fathom)

2.5, 5, 7.5, 10,15, 20, 25, 30, 35, 40, 45, 50, 55, 60,70, 80, 90, 100, 110, 120, 130, 140, 150, 160, 180, 200

(feet) 10, 15, 20, 30, 40, 50,60, 80, 100,120,140, 160,180,200,220,240,260,280,320, 360, 400, 450, 500, 550, 600, 650

Dual frequency

Shift Automatic or manual

Display color 16 colors (red, orange, yellow, green, light green, white, light blue, blue

93132801-00 3-1

(meter / Japa nese fathom / fathom / Italian fathom)

0 to 3000

(feet)

0 to 8000

and neutral colors) (Color pallet can be changed.)

Background (9 colors)

Page 18

Chapter 3 CVG-200

Specifications

Picture mode N: Normal (incl. SHIFT) Z1: (Zoom1) Bottom Lock Z2: (Zoom2) Bottom Discrimination Z3: Bottom Zoom BZ: Bottom Zoom (H): High frequency (L): Low frequency

In a split display, the screen positions can be swapped. The display can also be switched in-between vertical and horizontal partitioning.

・

High/Low frequency

Single display

Dual display

・

High/Low freq. : Normal ・High/Low freq.: Bottom Zoom

(L)

(H)

the above display modes.

(H)

(L)

-scope display can be added to each of

Interference rejection 3 steps (OFF, 1, 2) Color rejection 15 steps (one out of 15colors)

Alarm Fish alarm, Depth alarm Image speed Fixed 12 speed (4/1, 3/1, 2/1, 1/1, 1/2, 1/3, 1/4,

1/6, 1/8, 1/12, 1/16) and Stop

Output reduction 2 steps (Standard and reduced) Pulse width 4 steps (Very narrow, Narrow, Middle, Wide)

Color tone 3 steps (1, 2, 3) Background color 9 steps (1, 2, 3, 4, 5, 6, 7, 8, 9)

Depth display 4 steps (Off, Large, Middle, Small) Depth display position 2 steps (Down or Up) Depth scale display 3 ways (Off, One, All) Scale position 2 ways (Edge or Center)

Scale numeral display 2 ways (Large or Small) Time mark 3 ways (Off, 10 sec, 1 min)

Image feed direction 2 ways ( ) Image split

Image swap

A B , B A

Water temperature 3 ways (Off, oC, oF) Auto function Depth range, shift, gain Depth unit 5 kinds (m, J.fm, fm, I.fm, ft)

Bottom detection range 2 ways (Within or outside the sonar display) Depth sounding 3 ways (Auto, High frequency, Low frequ ency) Marker Depth marker (VRM) 2 Line, Scale, Zoom range marker,

Key (used only for the

following functions)

Alarm range marker, Time maker, Color pattern GAIN (Gain, Enhancement, STC) SHIFT, VRM, RANGE, MODE

Other functions Enhancement, White line, A scope, Water Temperature graph, Draft,

Bottom detection start position, Sonic correction, Temperature correction, Speed correction, INT/EXT sync switching, PRR, Color change, INT/EXT Water temperature switchin g, Bottom detection threshold

3-2 93132801-00

Page 19

CVG-200 Chapter 3

Specifications

3.1.3 Specifications of Plotter

Map mode Mercator projection Display mode North-up, East-up, South-up, West-up, Course-up (Waypoint),

Head-up and Centered North-up

Zooming range 0.01 to 3,600 n m(0.02 to 6,600 km) around Equator Effective map creation area Below the latitude 75 degree

Time 1, 2, 5, 10, 20, 30, 60, 120, 300, 600 sec Plotting interval Distance 0.01, 0.02, 0.05, 0.1, 0.2, 0.5, 1.0, 2.0, 5.0, 10.0 nm (km)

Number of plots 2,000, 4,000, 7,000 (maximum plot) x 7 blocks Track color 7 colors(Normal/Depth/Temperature : changeable) Position data display Navigation data display Own ship’s position, Own ship’s course, Own ship’s speed, Waypoint

Position registration 8,300points (All points can be registered as waypoint) Mark color 7 colors Mark shape

Route 50 routes(1route 50 waypoints), user can add comments (up to 12 Graphics

Alarm Arrival, POB, Cross track error Position correction By cursor Magnetic compass correction Tracking other ships track *1 Memory backup By Lithium battery ( for SRAM backup) and Non-volatile ROM Other function Displays names of places, Ring markers, stores landmark data,

*1 : ATA information from a radar unit required.

Drawing nodes Display color

Lat/Lon, Loran C LOP, Decca LOP position, Waypoint bearing, Waypoint distance, POB position, POB

bearing, POB distance, Cursor position, Cursor bearing, Cursor distance

(The mark are only useable in Mark Editing mode) characters)

3,500 points(500 points x 7blocks) 7colors

Auto, Manual Track up to 10 other ships. Each ship’s course can be tracked and

recorded for a course consisting of up to 1000 points.

calculates the distance between two points, Draw Parallel Lines, information windows, stores/retrieves memory card data.

93132801-00 3-3

Page 20

Chapter 3 CVG-200

Specifications

3.2 Serial Data

Input data

Type: NMEA0183 Ver.2.0/1.5 Sentence: GPS/DGPS(J5)

HDT, GGA, GLL, MSK, MSS, PKODA, PKODG, RMC, VTG, CH1(J2), CH2(J6) HDT, MTW, TLL, TTM

Output data

Type: NMEA0183 Ver,2.0 Sentence: CH1(J2)

APB, BWC, GGA, GLL, GTD, RMB, VTG, WPL, XTE, ZDA CH2(J6)

APB, BWC, GGA, GTD, VTG, WPL, ZDA

3-4 93132801-00

Page 21

CVG-200 Chapter 3

Specifications

3.3 Power Requirements

Input voltage: 10.8 to 31.2 Power consumption: Less than 45W (at AC Operation: AC/DC rectifier

Input voltage range: 100/ Voltage fluctuation allowance: Frequency fluctuation allowance:

VDC

PS-006

115 VAC

24 VDC)

is required.

or 200/

+/- 10%

47 to 63 Hz

230 VAC

3.4 Environmental Conditions

(1) Temperature and humidity

Operation temperature: Storage temperature: Humidity:

93%

+/-

3% @+40oC

(2) Vibration

The equipment operates normally under the following vibrating conditions:

5 Hz - 13.2 Hz: Amplitude +/-1mm+/-10% (Maximum acceleration of 7m/s

13.2 Hz-60 Hz: Maximum acceleration of 7 m/s

(3) Water proof

IPX5(Water jet proof)

-15oC to +55oC

-30oC to +70oC

being applied

at 13.2 Hz)

3.5 External Dimensions and Weight

External dimensions: Width x Depth x Height unit (mm)

Dimensions: 380 x 138 x 340 Weight : 6.8 Kg

Dimensions:

320

380

340

138

20 24

100 29.5

Figure 3.1 External dimensions of CVG-200

93132801-00 3-5

Page 22

CVG-200 Chapter 4

Installation

Chapter 4

Installation

Page No.

4.1 Installation Consideration..............................................................................4-1

4.2 Unpacking of The Box .................................................................................... 4-1

4.3 Inspection of The Equipment.........................................................................4-1

4.4 Proper Location for Setup..............................................................................4-1

4.5 Cable Routing and Connections....................................................................4-1

4.6 Display Installation..........................................................................................4-2

4.6.1 Table mounting........................................................................................................................ 4-2

4.6.2 Flush mounting ...................................................................................................................... 4-3

4.7 Inter-connections of The System...................................................................4-5

4.7.1 Preparation of DC Power cable (CW-253-2M)....................................................................... 4-6

4.7.2 Connecting the Transducer and Temperature/Speed Sensor.................................................4-6

4.7.3 Layouts of the Pin Connections.............................................................................................. 4-8

4.8 Post-installation Inspections..........................................................................4-8

93132801-00 Contents

Page 23

CVG-200 Chapter 4

Installation

Chapter 4 Installation

4.1 Installation Considerations

Qualified service technicians should perform the installation of CVG-200 that comprises of the following operations: (1) Unpacking each component of the system. (2) Inspection of the exterior of each component unit and accessory. (3) Checking the ship’s mains voltage and current capacity . (4) Determining the installation site. (5) Installing the Display unit. (6) Mounting the accessories. (7) Planning the cable routing and connections. (8) Adjustment and setups.

4.2 Unpacking of The Box

Unpack your package and check if all of the items stated in the packing list are contained in the package. If not, report this to an insurance agent for tracing missing good s or refund.

4.3 Inspection of The Equipment

Carefully check the exterior of each component unit for dents, damage, etc. In particular, the LCD is vulnerable to physical damage. During transportation, the LCD is liable to breakage despite its protective packing.

4.4 Proper Location for Setup

To achieve best operational performance, the following factors must be considered. (1) The display unit should be positioned in the location where the external situation can be viewed. (2) This unit should be positioned where the navigator or operator can easily see the screen. (3) Select a position safe and free from dampness, water spray, rain and direct sunlight. (4) Provide enough space for servicing. Consider access to the rear panel for connecting various

cables.

(5) Position the display unit as far away as possible away from other radio equipment.

4.5 Cable Routing and Connections

(1) The transducer cables should be securely fastened to the display using cable clamps and run

separately away from other cables such as, radio antenna feeder, power cables, etc. Under no circumstances should it be in parallel arrangement with other cables. These precautions are essential to avoid radio interference to/from other equipment installed on the ship. If this arrangement is not possible, either cable set should be screened with a metal conduit or another form of shielding.

93132801-00 4-1

Page 24

Chapter4 CVG-200

Installation

(2) The display unit should be grounded to the hull with a wire cut as short as possible. We

recommend using a wide and heavy copper braid or plate to be connected to a grounding stud at the rear of the display unit.

(3) The power supply cable should be connected directly to the ship’s battery to avoid RF noise

conducted from other equipment on board.

4.6 Display Installation

The display unit is designed for table mount and flush mount. Refer to the following description for installation (Refer to Figure 4.1 to 4.4)

4.6.1 Table mounting

(1) Remove the two knurled fixing knobs that fix the display unit to the mounding bracket. (2) Remove the display unit from the bracket and place it on a flat and safe area. (3) Place the mounting bracket to the place where the display unit is to be installed, and fix the

bracket with four (4) M5 tapping screws. Provide enough space for servicing. (Refer to Figure 4.2)

(4) Reset the display unit on to the bracket and fix it using the two knobs that were removed in step

(1)

Fixing screws (M5 screw, 6pcs)

Display unit

Mounting

Mounting bracket

Washer

4-2 93132801-00

Installation surface

Figure4.1 Fitting detail

Knurled fixing bolt (M6 stainless bolt)

Page 25

CVG-200 Chapter 4

Installation

Figure 4.2 Servicing Access space required

113

100

Unit in mm

113

4.6.2 Flush mounting

(1) Cut a rectangle opening. (Refer to Figure 4.4) (2) Loosen two (2) fixing bolts that fasten the display unit on to the mounting bracket. (3) Remove four (4) plastic screw covers, which are fitted on each corner of the display front face.

(Pull up and out for easy removal.) Do not lose these screw covers.

(4) Put the display on the opening and fix with four (4) tapping screws. In case you use M4 screws to

fix the display, select an appropriate screw length that best suits fixing the unit to the panel thickness.

(5) Refit the covers removed in step (3).

Display unit

Fixing screws (M4 screws, 4 pcs)

Screw covers (4 pcs)

Figure 4.3 Flush mounting

93132801-00 4-3

Page 26

Chapter4 CVG-200

Installation

308

Fixing holes for M4 screw

274

4 4

306

300

308

2 2

16 268

Figure 4.4 Dimensions of opening and fixing holes for flush mounting

4-4 93132801-00

Page 27

CVG-200 Chapter 4

Installation

4.7 Inter-connections of The System

As pictured in Figure 4.5, connect the various cables to their prescribed locations on the rear panel of the display unit.

NMEA0183 CH1

CW-381-5M

CW-374-5M

CW-373-5M

CW-374-5M

CW-376-5M

Marine Radar with ATA

MDC-721/741/740 MDC-1541/1540/1560/1510 MDC-1021/1041/1040 MDC-1121/1141/1140

Marine Radar with ATA

MDC-3641/3642/3840

Marine Radar

MD-3420/3441 MD-3641/3642 MD-3840 MD-3010/3020/3050/3210series

Color Fish finder

CVS-841 CVS-842 CVS-852

Color Fish finder

CVS-108/118 CVS-832 CVS-8841/8842/8816 CVS-8851/8852 CVS-8826/8826S series

Autopilot

GPS sensor

GPS-20A

DGPS sensor

KBG-2

This cable is included.

Junction box

JB-10 JB-12

CW-154A-5M

CW-376-5M

CW-154A-5M

Marine Radar

MD-3420/3441 MD-3641/3642 MD-3840 MD-3010/3020/3050/3210 series

Color Fish finder

CVS-841 CVS-842 CVS-852

Color Fish finder

CVS-108/118 CVS-832 CVS-8841/8842/8816 CVS-8851/8852 CVS-8826/8826S series

CVG-200 Rear Panel

External monitor

(Analog RGB)

External monitor and Extension cord to be provided by the user.

Fish finder

・NMEA 0183

CH2 Junction box

JB-10 JB-12

J5 J6

POWER

This cable is

CW-840-0.3M

DC Power cable

CW-253-2M

Water temperature/Speed sensor

ST-80-1, ST-90-1, ST-100-1

Water temperature sensor

T-81

Cable ground or ship’s hull

Transducer 500T-2B / 500T-3B / 501T-3B

AC/DC

rectifier

(Refer to CH1)

VV-2D8-3M

Transducer TD-501C

100/115VAC 200/230VAC

10.8～31.2VDC

Figure 4.5 Inter-connections

93132801-00 4-5

Page 28

Chapter4 CVG-200

Installation

4.7.1 Preparation of DC Power cable (CW-253-2M)

To Display unit

4.7.2 Connecting the Transducer and Temperature/Speed Sensor

The connectors for TD-500T-2B/500T-3B/501T-3B transducer are equipped with 8-pin water resistant connector (LTW). The 8-pin water resistant connector (LTW) of the TD-500T-2B/500T-3B become 5 lead wires. These lead wires are utilized when connecting the optional Temperature/Speed Sensors (ST-80-1, ST-90-1, ST-100-1 and T-81). Also, the TD-501T-3B transducer is equipped with a water temperature sensor.

4.7.2.1 Connecting the Transducer

White Black Gray

Red

Green

DC+ DCGND Ext. buzz. out Ext. buzz. out

1) TD-500T-2 B/500T-3B Connect to the J3 connector on the back of the receiver display unit. Use the blue, purple, green, red and black wires when connecting the temperature/speed sensor.

2) TD-501T-3B (with Water Temperature Sensor) Connect to the J3 connector on the back of the receiver display unit.

3) TD-500T-2 /500T-3/501T-3/501C

The user must have the cable, CW-840-0.3M (option)for the tr ansducer.

Solder the transducer to CW-840-0.3M while referring to the table on connecting transducers. After soldering is completed, please be sure to add water-resist ance and insulation by applying electrical tape (or other such tap e) onto the soldered part of the cable.

CW-840-0.3M

2 lead wires

3 TD1 (orange)

4 Shield

5 TD2 (white)

1 SPD.PULSE (blue)

To Transducer

4-6 93132801-00

Lead wires

2 SPD.VCC (purple)

8 SPD.GND (black)

6 TEMP.VCC (green)

7 TEMP.SIG (red)

To Speed Sensor

To Temperature Sensor

Page 29

CVG-200 Chapter 4

)

Installation

Transducer Connection Table

Transducer Cable Transducer

2 lead shield

wire number

3 orange red black 4 shield shield shield 5 white white white

4.7.2.2 Connecting Water Temperature/Speed Sensors

Solder the wire protruding from TD-500T-2B/500T-3B or CW-840-0.3M, while referring to the table on connecting water temperature/speed sensors. After soldering is completed, please be sure to add water-resistance and insulation by applying electrical tape (or other such tap e) onto the soldered part of the cable.

2 lead shield

wire color

TD-500T-2 TD-500T-3

TD-501T-3

TD-501C

Lead wires

Water Temperature/Speed Sensor Connection Table

CW-840-0.3M

TD-500T-2B

Water Temperature/Speed Sensor

TD-500T-3B

Lead Wire

Number

1 2 6

7 8

Lead Wire

Color

blue

purple

green

red

black

T-81

Note1

― ―

ST-80

ST-80-1

green green green

red red red

gray white white white gray brown brown brown

―

shield shield shield

Note 1: 2 gray colored wires protrude from T-81.

1 SPD.PULSE (blue))

2 SPD.VCC (purple

8 SPD.GND (black)

6 TEMP.VCC (green) 7 TEMP.SIG (red)

ST-90

ST-90-1

ST-100

ST-100-1

To Speed Sensor

To Temperature Sensor

TD-501T-3

― ―

green

red

―

Please connect the proper wires to the green and red wires of CW-840-0.3M.

93132801-00 4-7

Page 30

Chapter4 CVG-200

②

)

②

(

)

Installation

4.7.3 Layouts of the Pin Connections

The connector pin layouts pictured in J1 to J6, POWER shows a view from the rear of the receiver display unit. (The views of the plugs are shown from the soldered side of the plug.)

・External Monitor output

Ｊ1

①

②

⑪

③

④

⑨ ⑩

⑧

⑦

⑫

⑥

⑤

・TD, Water temperature/Speed

Ｊ３

①

②

⑧

③ ④ ⑤

⑦

⑥

①Ｒ (red) （OUT） ②GND （OUT） ③G (green) （OUT） ④GND （OUT） ⑤B (blue) （OUT） ⑥GND （OUT） ⑦H (Horizontal) （OUT） ⑧V (Vertical) （OUT） ⑨GND （OUT） ⑩NC （N.C.） ⑪GND （OUT） ⑫GND （OUT）

①SPD.PULSE (IN)

SPD.VCC (OUT ③TD1 (In/Out) ④TD_SHIELD ⑤TD2 ((In/Out) ⑥TEMP.VCC (OUT) ⑦TEMP.SIG (IN) ⑧SPD.GND

・NMEA In/Out (CH1)

Ｊ２

①GND

⑤

①

⑥

②

④

③

・Remote control, Fish finder Input

Ｊ４

①

⑦

②

⑥

③ ④ ⑤

②TX1+（OUT） ③TX1-（OUT）

④RX1+（IN） ⑤RX1-（IN） ⑥NC （N.C.）

①RXD (IN)

TXD (OUT) ③+5V (OUT) ④GND ⑤S.TRIG-IN (IN) ⑥GND ⑦GND

・GPS_ANT Input

①

②

Ｊ５

⑥ ③

⑤

④

①GND ②GPSOUT+ (OUT) ③GPSOUT- (OUT) ④GPSIN+ (IN) ⑤GPSIN- (IN) ⑥+12V

OUT

・NMEA In/Out (CH2)

Ｊ6

⑤

①

⑥

②

④

③

①GND ②TX2+（OUT） ③TX2-（OUT） ④RX2+（IN） ⑤RX2-（IN） ⑥Not in use（N.C.）

・ＤＣ Input（10.8～31.2VDC）

POWER

①

②

③

⑤

④

①DC- (IN) ②DC+ (IN) ③EXT.BUZ0 ④EXT.BUZ1 ⑤Frame GND

4.8 Post-installation Inspections

Before you turn the CVG-200 on, check the following points to make sure the CVG-200 operates properly: (1) Is the ship’s supply voltage and current within the prop er range? Input voltage: 10.8 to 31.2 VDC at POWER connector (2) Are the ca bles routed and connected properly? No wrong connections, no short circuits, etc?

4-8 93132801-00

Page 31

CVG-200 Chapter 5

Basic Operation

Chapter 5

Basic Operation

Page No.

5.1 Name and Function of Parts...........................................................................5-1

5.1.1 Control Panel........................................................................................................................... 5-1

5.1.2 Display Unit..............................................................................................................................5-2

5.2 Displaying the Image ......................................................................................5-3

5.2.1 Power On/Off........................................................................................................................... 5-3

5.2.2 Brightness Setting ................................................................................................................... 5-3

5.2.3 Choosing the Display............................................................................................................... 5-3

5.3 Plotter Screen..................................................................................................5-4

5.3.1 Discovering Current Position................................................................................................... 5-4

5.3.2 Moving the Display without the Cross Cursor ......................................................................... 5-4

5.3.3 Moving the Display with the Cross Cursor .............................................................................. 5-5

5.3.4 Display of Distance between Two Points and Bearings.......................................................... 5-6

5.3.5 Altering Scale of Map Display..................................................................................................5-7

5.3.5.1 Magnification of Map Display............................................................................................. 5-7

5.3.5.2 Reduction of Map Display.................................................................................................. 5-7

5.3.5.3 Fixed Scale ........................................................................................................................ 5-7

5.3.6 Settings of Tracks.................................................................................................................... 5-8

5.3.6.1 Display of Tracks................................................................................................................5-8

5.3.6.2 Track Color Settings........................................................................................................... 5-9

5.3.6.2.1 Normal Track Coloring.................................................................................................... 5-9

5.3.6.2.2 Depth-based Coloring..................................................................................................... 5-9

5.3.6.2.3 Water Temperature-Based Coloring.................................................................................. 5-9

5.3.6.3 Deleting Tracks................................................................................................................5-10

5.3.6.3.1 Procedure for Color-Based Track Deletion...................................................................... 5-10

5.3.6.3.2 Procedure for Range-Based Deletion ............................................................................. 5-10

5.3.7 Mark Settings..........................................................................................................................5-11

5.3.7.1 Mark Color Settings ..........................................................................................................5-11

5.3.7.2 Registering Marks...................................................................................................... .......5-11

5.3.7.2.1 Registration of Current Position ......................................................................................5-11

5.3.7.2.2 Registration of Cross Cursor Current Position ..................................................................5-11

5.3.7.3 Mark Deletion................................................................................................................... 5-12

5.3.7.3.1 Deletion Based on Color and Shape of Mark................................................................... 5-12

5.3.7.3.2 Deletion by Cross Cursor .............................................................................................. 5-12

5.3.7.4 Storing Events.................................................................................................................. 5-13

5.3.8 Setting Waypoints.................................................................................................................. 5-14

5.3.8.1 Setting a Registered Mark as Waypoint...........................................................................5-14

5.3.8.2 Using the Cursor to Register Waypoints.......................................................................... 5-15

5.3.8.3 Switching the Waypoint.................................................................................................... 5-15

5.3.8.4 Resetting the Starting Point of the Waypoint................................................................... 5-16

5.3.8.5 Removing Waypoints.......................................................................................................5-16

5.3.9 POB Settings.........................................................................................................................5-17

5.3.9.1 PCB Position Settings......................................................................................................5-17

5.3.9.2 Resetting the POB...........................................................................................................5-17

5.3.9.3 Deleting the POB.............................................................................................................5-17

5.3.10 Route Setting....................................................................................................................... 5-18

5.3.10.1 Choosing Routes from List............................................................................................. 5-18

5.3.10.2 Setting Route by Cross Cursor......................................................................................5-20

5.3.10.3 Switching the turn-around point..................................................................................... 5-20

93132801-00 Contents

Page 32

Chapter 5 CVG-200

Basic Operation

5.3.10.4 Resetting the Route Start Point......................................................................................5-21

5.3.10.5 Deleting Routes..............................................................................................................5-21

5.3.11 Entering Values and Comments...........................................................................................5-22

5.3.12 Object Information................................................................................................................5-23

5.4 Operation of Sounder Display..................................................................... 5-25

5.4.1 Sounder Display Options.......................................................................................................5-25

5.4.1.1 About The Modes .............................................................................................................5-25

5.4.1.2 Regarding Display Images...............................................................................................5-26

5.4.1.3 Procedures for the Sounder Display................................................................................5-27

5.4.1.3.1 Normal Display Procedure.............................................................................................5-27

5.4.1.3.2 Procedure for Displaying High and Low Frequency Mode together....................................5-27

5.4.1.3.3 Procedure for Displaying Magnified High Frequencies......................................................5-28

5.4.1.3.4 Procedure for Displaying Magnified Low Frequencies ......................................................5-28

5.4.2 Range（Sounding Range）Selection ...................................................................................5-29

5.4.3 Adjustment of Gain and STC .................................................................................................5-30

5.4.4 Operation of the [Shift] Key....................................................................................................5-33

5.4.4.1 Fix Shift Settings ..............................................................................................................5-33

5.4.4.2 Auto Shift Settings............................................................................................................5-34

5.4.5 Operation of Variable Range Markers (VRM) ......................................................................5-35

5.4.5.1 Normal Image Mode) ......................................................................................................5-35

5.4.5.2 Combined Imaging...........................................................................................................5-36

5.4.5.2.1 Vertical Partitioning.......................................................................................................5-36

5.4.5.2.2 Horizontal Partitioning...................................................................................................5-38

5.4.6 Setting Positions for Part Expansion mode ...........................................................................5-39

5.4.6.1 Vertical Partitioning...........................................................................................................5-39

5.4.6.2 Horizontal Partitioning......................................................................................................5-40

Contents 93132801-00

Page 33

CVG-200 Chapter 5

BRT

DISP

CLR

INFO

ENT

CURS

GOTO

POB

Basic Operation

Chapter 5: Basic Operation

5.1Name and Function of Parts

5.1.1 Control Panel

GAIN

SHIFT VRM

Slot for Optional Memory Card

On/Off and setting switch for the SHIFT function. Settings and changes carried out by the knob.

On/Off and setting switch for the VRM function. Settings and changes carried out by the knob.

Sets and adjusts gain, emphasis, and STC functions. Settings and changes carried out b

Control knob for the various functions on this panel.

the knob.

Displays the circle( )mark.

Displays the( )mark.

Sets the color of the tracks. However, when the track color is in temperature-based o water depth-based, the colors cannot be changed.

Track recording On/Off switch.

Specifies waypoint and engages the “Go To” Mode.

Enlarges size of map display.

Selects the fixed scale.

Moves the cursor and display area.

lso used for selecting menu items.

RANGE

MODE

MARK

COLOR

TRACK ON/OFF

TRACK COLOR

SCL

MARK

ERASE

TRACK ERASE

ROUTE

CANCEL

Increases Detecting Range

Decreases Detecting Range

Selects the Display Mode. Settings and changes carried out by the knob.

Displays the square( )mark.

Displays the triangle( )mark.

Sets the color of the mark.

Erases the mark.

Deletes tracks.

Specifies a route and engages the Route Mode.

Sets the anchor point and engages the anchor mode.

Reduces size of map display.

On/Off display switch for the cross cursor.

Cancels operations requiring confirmation from the User.

Deletes the anchor point and waypoint.

Displays the menu.

Selects the display screen.

POWER

Confirms operations requiring confirmation from the User. Displays the distance & bearings in-between 2 points on the screen.

Displays weather information.

djusts the screen brightness.

Use the directional key above.

Power Switch ON/OFF

93132802-01 5-1

Page 34

Chapter 5 CVG-200

Basic Operation

5.1.2 Display Unit

Boat Bearings

06’

3388°

0055..001188N

26’

113388°

2277..661111E

000088..00°

28’

18.6kt

M A R K

TT RR K

30’

Route Speed

Mark Color

Water Temperature

Plotter Screen

Map Scale

Time mark (1 min increments)

Screen Mode

Rainbow Pattern

Sounder Display

Boat Speed

Water depth

Cross track error

Compass

04’

高

XTE

0.5nm

３３００

２２５５

２２００

℃

2255..22℃

2211..55KKt

11550

Water Temp Graph

WPT No

BRG

HDG

CDI

Right 085.9°

Scale Value

00000

068.1°

154.0°

０

１００

２２００００

Scale Mark

Waypoint Number

Bearings to waypoint

Heading

Course Deviation Angle

Track Color

Magnification Mark

Alarm Mark (school of fish)

Alarm Mark (sea bed)

A Scope

Highway

TTG

21：00

ETA

07：25

BRG

068.0°

Time to go from present position to WPT

Estimated Arrival Time

Bearings

Boat Position

RNG

419 nm

Range

5-2 93132802-01

Page 35

CVG-200 Chapter 5

Basic Operation

5.2 Displaying the Image

5.2.1 Power On/Off

When the power is off, press

to turn the power on.

Also, when the power is on,

pressing turns the power off.

KODEN

CVG-200

KMC-92 VerX.X（WGS-84）

The information displayed on this equipment shall be used for reference only. Authentic navigation charts shall be used when navigation judgment is required.

- - CAUTION - -

KODEN ELECTRONICS CO., LTD

Backup Battery cell OK

System test OK

This display appears when the power is switched on.

5.2.2 Brightness Setting

Push , and the brightness display shall appear.

Push the directional key or to set the brightness. You can also adjust the brightness one increment at a time by pressing repeatedly. A brightness setting left without adjustment for over 5 seconds will be taken as the current setting. The user may alter the preset factory brightness. To record the user’s brightness setting, follow the procedure outlined below:

→ “etc”→ “Maintenance”→ “System Test”→

Caution display

Dark

Brightness

Brightness Display

Bright

“Brightness”→ [Set]→

5.2.3 Choosing the Display

Push repeatedly to pull up various pre-stored display screens. The user can store or delete displays according to the procedure outlined belo w:

→ “etc”→ “Screen Display Registration”→ [set] →

Caution

On Head up and Own ship center fix mode, sounder and plotter combined screen cannot be selected.

93132802-01 5-3

Page 36

Chapter 5 CVG-200

Basic Operation

5.3 Plotter Screen

5.3.1 Discovering Current Position

The current position of the user’s boat is displayed through the latitude and longitude (appearing in the upper left hand corner of the display) or by the LOP.

Current Position

3355°°

1100..882255N

30’ 50’

114400°

3399..117722E

000066..00ﾟ

40’

ﾟ

002211..00kkt

20’

10’

00’

5nm

Track off

Displaying the LOP allows the user to choose between LORAN C or DECCA. Displaying the current position is done by the following procedure:

→ “Plotter” → “Display Settings” → “Position Data Display”→

[set]→

5.3.2 Moving the Display without the Cross Cursor

The user can move the display using the directional key.

There are two types of display movements: “viewpoint” and

“chart.”

Choose “viewpoint,” and the map moves in the opposite

direction that the user pushes the directional key.

Chose “chart,” and the map moves in the same direction

that the user pushes the directional key.

When the cross cursor is not displayed, the limit of map movement coincides with the display limit of the scope of the boat’s position. Settings for screen scrolling are set as follows:

→ “Plotter” → “System Settings” → “Screen Direction” →

[Set] →

Boat Position

Range of Screen

Possible Scroll Range

5-4 93132802-01

Page 37

CVG-200 Chapter 5

Basic Operation

5.3.3 Moving the Display with the Cross Cursor

Using the cross cursor allows for free movement of the screen. Push and the cross cursor will appear on the plotter screen. Push the directional key and the cross cursor will move in the same direction. While the cross cursor is displayed, its latitude and longitude as well as the cursor’s distance to the user’s boat is displayed in a transparent window in the upper right-hand part of the screen. With the cross cursor displayed, pressing once more causes the transparent window to disappear.

3355°°

36°

3377..007755N

113377°

4444..774422E

138° 139°

N E

CCOOG

331155..00°

SSOOG

113399ﾟﾟ0033..005511E

008800..00ﾟ

1188..66kkt

3355ﾟﾟ5599..446655N

MMAARRK

TRK

ﾟ 22..1111nnmm

Cross Cursor’s Latitude, Longitude

Distance between the cross cursor and boat’s current position

Cross Cursor

35°

Track Off

93132802-01 5-5

Page 38

Chapter 5 CVG-200

Basic Operation

5.3.4 Display of Distance between Two Points and Bearings

Using the cross cursor enables the user to calculate the distance between two points as well as bearing.

Push and the cross cursor shall appear on the plotter.

Move the cross cursor to the desired cardinal point, and press . A screen showing the distance between two points shall appear.

Geodesic Line

Distance = 0.00nm Bearing = 000.0°

Move the cross cursor to where you want to measure distance and bearings in relation to the

cardinal point and press .

On the “Two-Point Display” the distance and bearings shall appear.

Cardinal point

2nd point

Geodesic Line

Distance = 15.00nm Bearing = 045.0°

Move the cross cursor once again, and the distance between the cardinal point and this new point can be displayed.

Press any key except for , and the “Two-Point Display” shall close.

5-6 93132802-01

Page 39

CVG-200 Chapter 5

Basic Operation

5.3.5 Altering Scale of Map Display

5.3.5.1 Magnification of Map Display

Press and the user can magnify the map display. Normally, magnification takes place with the boat being in the center. When the cross cursor is displayed, rather than the boat being the center-point, the cross cursor is taken as the center-point.

5.3.5.2 Reduction of Map Display

Press and the user can reduce the map display. Normally, reduction takes place with the boat being in the center. When the cross cursor is displayed, rather than the boat being the center-point, the cross cursor is taken as the center-point.

5.3.5.3 Fixed Scale

Press repeatedly and the user can choose from three pre-set fixed scales. Normally, magnification/reduction takes place with the boat being in the center. When the cross cursor is displayed, rather than the boat being the center-point, the cross cursor is taken as the center-point.

Using the Fixed Scale option enables the user to quickly choose from three frequently used display scales. To create and store a new fixed scale, follow the procedure outlined below:

→ “Plotter” → “System Settings” →

“Fixed Scales 1-3” → [Set] →

93132802-01 5-7

Page 40

Chapter 5 CVG-200

Basic Operation

5.3.6 Settings of Tracks

5.3.6.1 Display of Tracks

Press recording of tracks can be activated or deactivated. Activating track recording causes “Turns on a ship’s track display.” to appear on the

display. The number of tracks shall appear on the lower right-hand corner of the plotter.

Deactivating track recording causes “Turns off a ship’s track display.” to appear on the

display. Only the mark showing the boat’s current position shall move. The lower right-hand corner of the plotter shall display “Track Display Suspended.” Activating track recording shall once again commence track recording from the boat’s current position.

To set the interval for track recording, follow the procedure outlined below:

→ “Plotter” → “System Settings” → “Plot Interval” →

[Set] →

The number of plotting points for track recording are set as follows: 2000, 4000, and

7000. You can change the setting by the following procedure:

→ “Plotter” → “System Setting” → “Number of Plot” →

[Set] →

Should the number of plotting points exceed the setting, the previous plotting points shall be overwritten with the new data, starting with the oldest data being overwritten first. Important data can be stored by the following procedure:

→ “Plotter” → “Track Store” → [Set] →

Turns off a ship’s track display

TRK

Track Off

Turns on a ship’s track display

0395

TRK

Track Color

Track Display “OFF”

Display of Number of Plots

5-8 93132802-01

Page 41

CVG-200 Chapter 5

Basic Operation

5.3.6.2 Track Color Settings

There are 3 types of Settings for Track Color: “Normal”, “Sounding RESP”, and “W_Temp RESP.”

Normal: Manually choose from 7 colors in this setting.

Sounding RESP: Based on the depth of the water, the color of the tracks shall be automatically

colored. When the water depth cannot be measured, the tracks are automatically assigned a green color.

W_Temp RESP： Based on the water temperature, the color of the tracks shall be automatically

colored. When the water temperature cannot be measured, the tracks are automatically assigned a green color.

Procedure for selecting settings is as follows:

→ “Plotter” → “Track Color” → [Set] →

5.3.6.2.1 Normal Track Coloring

Push and the track color selection window shall appear.

The cursor in the selection window indicates which color is the

current setting.

The cursor may be moved up or down using the directional keys: or Should the setting remain unaltered for more than 5 seconds, the color upon which the cursor is resting shall be designated as the current color setting.

5.3.6.2.2 Depth-based Coloring

When the track colors are determined by depth, pressing

shall cause the window at the right to appear.

In these cases, the track colors cannot be changed.

Setting track coloring to depth-based coloring can be done as follows:

→ “Plotter” → “Track Color” → [Set] →

Track Color

Cursor

Track Color

Dependent on track color for depth is selected.

5.3.6.2.3 Water Temperature-Based Coloring

When the track colors are determined by water temperature, pressing shall cause the window at the right to appear. In these cases, the track colors cannot be changed.

Setting track coloring to water temperature based coloring can be done as follows:

Track Color

Dependent on track color for water temperature is selected.

→ “Plotter” → “Track Color” → [Set] →

93132802-01 5-9

Page 42

Chapter 5 CVG-200

Basic Operation

5.3.6.3 Deleting Tracks

Deleting tracks depends on the state of the cross cursor. Cross Cursor not displayed……….Deletion based on color Cross Cursor displayed……….Deletion based on specified range

5.3.6.3.1 Procedure for Color-Based Track Deletion

With the cross cursor not displayed, press and the

Track Erase

window to the right shall appear.

Choose the color of tracks to be deleted by using the

directional keys: or . Press to delete the tracks with the color specified by the cursor. When “All Colors” is specified by the cursor, all tracks shall be deleted.

5.3.6.3.2 Procedure for Range-Based Deletion

With the cross cursor displayed, press and the track/range deletion window shall appear.

Using the directional key, move the cross cursor to your designated first point and press .

Cursor

All Col or

Track Erase(area)

Move cursor to the 1’st point.

Next, using the directional key, designate a second point in order to form a deletion range in the shape of a rectangle. Press to delete the tracks within the rectangle.

Track

First point

Deletion Range

Second point

Track Erase(area)

Move cursor to the 2’nd point.

Caution

Deleted tracks cannot be recovered. Please confirm before deletion.

5-10 93132802-01

Page 43

CVG-200 Chapter 5

Basic Operation

5.3.7 Mark Settings

5.3.7.1 Mark Color Settings

Press and the mark color setting window shall

Mark Color

appear.

Use the directional keys to specify the mark color: or . Press to choose the color specified by the cursor.

5.3.7.2 Registering Marks

Registering marks depends on the state of the cro ss cursor. Cross Cursor not displayed……….Current position registered Cross Cursor displayed…………...Cross Cursor’s current position registered

Mark numbers are displayed beginning from lowest number first within the selected block of marks. When the selected block of marks is not empty, marks cannot be registered. Choosing a block of marks is carried out by the following procedure:

→ “Plotter” → “Mark Block Number” → [Set] →

Cursor

5.3.7.2.1 Registration of Current Position

When the cross cursor is not displayed, push one of the following mark keys:

Doing so will leave a mark in the current position.

5.3.7.2.2 Registration of Cross Cursor Current Position

With the cross cursor displayed, push one of the following mark keys:

A mark is left in the cross cursor’s current position.

93132802-01 5-11

Page 44

Chapter 5 CVG-200

Basic Operation

5.3.7.3 Mark Deletion

Mark deletion depends on the state of the cross cursor. Cross Cursor not displayed……….Deletion based on color and shape of mark Cross Cursor displayed……….Deletion by Cross Cursor

5.3.7.3.1 Deletion Based on Color and Shape of Mark

With the cross cursor not displayed, press and the mark deletion window shall appear.

Push and choose among color to delete. Choose among shapes to delete by pressing: . Choose which specific colors and shapes to delete by pressing the following keys: or .

Press in order to delete the marks of the specified colors and shapes.

5.3.7.3.2 Deletion by Cross Cursor

Move the cross cursor onto the mark to be deleted.

Press and the mark erase window shall appear. Confirm which mark within the mark erase window is to be erased.

Mark Erase

Color

All Color

Color/Shape category cursor

Mark Erase

× ： 00101

When mark information is not displayed, point the cursor and press the Mark erase key.

Shape

All Shape

Cursor

Press and the selected mark shall be deleted.

Caution

Deleted marks cannot be recovered. Please confirm before deletion.

5-12 93132802-01

Page 45

CVG-200 Chapter 5

Basic Operation

5.3.7.4 Storing Events

Storing events may be labeled as Mark 00 to Mark 99. This information can be displayed on the top of the screen. The number of the mark being reported on can be changed. To utilize this function, the procedure outlined below must be done beforehand:

(1)

→ “Plotter” → “Mark Block Number” →

“Choose 00000” → [Set] → (2) → “Plotter” → “System Settings” → “Event Store” → “Choose 0 ~ 99” → [Set] →

After performing the procedure above, pressing the mark registration button or shall cause the event information window to appear in the upper right-hand corner of the plotter. Information on the specified mark shall appear in the event information window. When a mark is registered, the following information is displayed: bearings and distance from the boat, mark shape, mark number, and the latitude/longitude of the mark. Also, when date and time are added from an external source, this information is also displayed.

Bearing ---.-°

Distance ---- nm

00 --/--/--

--:--:--

Bearing ---.-°

Distance ---- nm

00 04/07/01

05:30:00

--ﾟ--.---

36 ﾟ 00.000N

---ﾟ--.---

138 ﾟ 00.000E

Mark not registered

Mark registered

When the event information window’s frame is red, the number of the mark can be altered.

Pushing on the directional key increases the mark number, while pressing on the directional key lowers the mark number. Any number between 00 and 99 are valid. When a displayed mark appears on the plotter, it shall blink. Should 5 seconds pass without further changes, the window frame shall turn black, signaling that changes to the mark number are no longer possible. To once again change the mark number, press . The window frame shall turn red, and the mark number can again be altered. Also, to remove the event information window, press . When entering information regarding an event, external fish finder entries and NMEA0183TLL sentences from POB from radars are acceptable. A red star mark (☆) is displayed when a TLL sentence signal is received. When the user wishes to only accept TLL sentences, set the Mark Block number to something besides 00000.

93132801-00 5-13

Page 46

Chapter 5 CVG-200

Basic Operation

5.3.8 Setting Waypoints

To set waypoints, the user can use a registered mark or move the cursor to the destination.

5.3.8.1 Setting a Registered Mark as Waypoint

In Waypoint mode, a specified point becomes the waypoint. In the operation shown below,

Waypoint mode begins with using the current position as a reference point.

(1) Confirm that the cross cursor is not displayed anywhere on the screen. (2) Press and the Waypoint Setting Wind ow shall appear.

Waypoint setting

0000

0 ：

(2) Using the key to choose the mark designated to be the waypoint. If the selected

mark is on the screen, it shall blink.

(3) Press and the position of the selected mark shall become the waypoint.

This mark is chosen as the waypoint.

Mark Number

Shape of registered mark (When no mark is registered, nothing shall

appear here.)

Mark No. 53 has been designated as the waypoint.

Information on the position of the waypoint is displayed here.

・When the waypoint is set, the bottom of the plotter shall display information pertaining to it.

35 ﾟ 16.289N 139 ﾟ 45.569E 277.3 ﾟ 44.1nm

Waypoint Mark

5-14 93132801-00

Waypoint Latitude / Longitude

Waypoint Bearings

Distance from boat to waypoint

Page 47

CVG-200 Chapter 5

Basic Operation

5.3.8.2 Using the Cursor to Register Waypoints

(1) Confirm that the cursor appears on the screen. (2) Press . (3) Use the key to move the cross cursor to your designated waypoint. Should a

mark enter the circular marks of the cross cursor, that mark shall be taken to be the waypoint.

(4) Press to set the cross cursor’s current position as the waypoint.

Move the cross cursor to the desired waypoint.

Waypoint information display

The flag signals that the waypoint has been set.

5.3.8.3 Switching the Waypoint

The waypoint can be switched to other marks that have been previously designated as waypoints. (1) Confirm that the cross cursor is not displayed on the screen. (2) Press and the Waypoint Operation Window shall appear.

(3) Press the key and choose mark number corresponding with the new waypoint. (4) Press and the selected mark number shall be designated as the new waypoint.

Waypoint setting operation

Waypoint has been setup

When switching between multiple waypoints, follow this procedure: Beforehand, write down on paper which marks you desire to be come waypoints.

93132801-00 5-15

Page 48

Chapter 5 CVG-200

Basic Operation

5.3.8.4 Resetting the Starting Point of the Waypoint

At the start point of the waypoint mode, the current position is taken to be the waypoint.

The procedure below allows for the establishment of a new startin g point.

(1) Press . (2) Press . The current position is now set as the new starting point.

5.3.8.5 Removing Waypoints

The procedure below outlines how to remove waypoints:

(1) Press .

(2) Press . The waypoint shall be removed.

53 53

Start point has been reset.

5-16 93132801-00

Waypoint removed.

Page 49

CVG-200 Chapter 5

Basic Operation

5.3.9 POB Settings

This is an emergency event function to mark the location of an accident such as a person overboard.

5.3.9.1 PCB Position Settings

Press and the POB position shall be set at the current position. As soon as the POB key is pushed, the anchor mark ( ) shall appear and the movement

of the boat shall be monitored.

The POB mode takes priority and overrides the waypoint mode and route mode.

5.3.9.2 Resetting the POB

The POB position is set when is pushed. The procedure below shows the way to set

a new anchor position.

(1) Push . (2) Push . The new POB position is now set.

5.3.9.3 Deleting the POB

Use the procedure below to delete the POB.

(1) Push . (2) Push . The anchor mode is now deleted.

93132801-00 5-17

Page 50

Chapter 5 CVG-200

Basic Operation

5.3.10 Route Setting

In order to determine settings for the route mode, a pre-registered route is required. Routes may be registered by the following procedure:

→ “Plotter” → “Route” → “Routing” →

“Chose creation method” → [Set] →

The procedure for setting the route depends on the state of the cross cursor. Cross cursor not displayed……….user must choose from a list Cross cursor displayed……….set the route directly using the cross cursor

5.3.10.1 Choosing Routes from List

With the cross cursor not being displayed, press , and the route window shall appear.

Route Execute

Route No Comment F/R

-- -------------- ---

01 6.30_AM RVS 02 RTE --.--.-- FWD 03 FWD 04 FWD 05 FWD 06 FWD 07 FWD 08 FWD 09 FWD 10 FWD

Cursor

Routes that fall within the scope of the plotter shall be displayed. The route corresponding with the cursor’s current position is

highlighted in red.

Use the directional keys or to move the cursor and select the number

corresponding to the desired route.

Push and the next route’s route window shall appear. Push and the previous route’s route window shall appear. Push and switch in-between the forward route and return route of the route highlighted by the cursor’s current position.

5-18 93132801-00

Page 51

CVG-200 Chapter 5

Basic Operation

The turn-around point of the route (shown by the flag) depends upon the route being either a forward route or a return route.

The boat’s initial turn-around point is designated by a flag.

Press to set the route. If no route is registered, nothing will occur even if the user presses the key.

Initial waypoint set

Present position

Waypoint information window appears

・Set the route and a waypoint information window like the one pictured below shall appear.

35 ﾟ 16.289N 139 ﾟ 45.569E 277.3 ﾟ 44.1nm

Route mode Waypoint mark

Waypoint latitude/longitude

Waypoint bearings

Distance to waypoint

93132801-00 5-19

Page 52

Chapter 5 CVG-200

Basic Operation

5.3.10.2 Setting Route by Cross Cursor

With the cross cursor displayed, press to

bring up the route window pictured to the right.

Move the cross cursor onto the route desired from

the route mode and press .

Once the route is recognized, the route number,

comments, and forward/reverse route settings are

displayed in the route window. With the route

number displayed, press to switch in-between

forward and reverse routes.

Press to set the route mode. If no route is registered, nothing will occur even if the user presses the key.

Route Execute

Route No Comment F/R

CANCEL : Cancel When point information is not displayed, point the cursor and press INFO key

Route Execute

Route No Comment F/R

ROUTE : FWD/RVS ENT : Execute CANCEL : Cancel

5.3.10.3 Switching the turn-around point

With the route mode in effect, pressing shall bring up the “Route Operation” window. With the route operation window displayed, pressing shall switch the turn-around point of the route. Press again and the next turn-around point shall be recognized as the waypoint, and the previous turn-around point’s flag shall disappear. If only 1 turn-around point remains, pressing shall display all turn-around points, and the first turn-around point shall be recognized as the waypoint.

5-20 93132801-00

Page 53

CVG-200 Chapter 5

Basic Operation

5.3.10.4 Resetting the Route Start Point

With the route mode in effect, press and the route operation window shall appear.

With the route operation window visible, press to designate the current position as the new start point.

5.3.10.5 Deleting Routes

Delete routes using the procedure given below:

（１） Press . （２） Press to delete the route.

Start point position

New Start point

93132801-00 5-21

Page 54

Chapter 5 CVG-200

Basic Operation

5.3.11 Entering Values and Comments

The user can enter comments (numbers and letters) through a specified, related plotter menu. The keys corresponding to various characters are arranged as shown below:

Pressing a given key repeatedly will bring up the various characters shown next to that key,

according to the order indicated by the arrows. Pressing the directional key or pressing

another of the keys pictured above shall move the cursor. The cursor moves one place to

the right when numbers are entered into menus where only numerical input is permitted

from the keys pictured above. From this point on, the keys pictured above shall be

collectively referred to as the numeric key pad.

1→A→B→C

4→J→K→L

7→S→T→U

0→#→_→ .

2→D→E→F

5→M→N→O

8→V→W→X

3→G→H→I

6→P→Q→R

9→Y→Z→&

5-22 93132801-00

Page 55

CVG-200 Chapter 5

Basic Operation

5.3.12 Object Information

Using this function, the information of objects shown on the chart can be displayed. Available information differs depending on whether the cross cursor is displayed or not as follows:

With the cross cursor OFF: The object information around the ship

INFORMATION window.

With the cross cursor ON: The object information around the cross cursor

OBJECT INFORMATION window.

To display the object information: (1) Press the INFO key. The OBJECT INFORMATION window will appear, showing the

object item.

(2) To change the item, press the INFO key again. The item shown changes each time the

key is pressed.

is shown in the OBJECT

is shown in the

Object Information

Anchor berth

Anchorage area Caution area Depth area Harbour area

↑↓ ：To select item.

→ ：To detail information.

CANCEL：Suspend

Object information window

93132801-00 5-23

Page 56

Chapter 5 CVG-200

Basic Operation

(3) To view the details of each item shown, press the ENT key. (4) When the content is in overleaf, an up and down arrow keys appear on the top and the

bottom edge of the page. To move to other page, press the up or down. (5) To return to normal display, press the MENU key. When no data is available, “No Chart Data” will appear.

Object Information (Detail)

Anchor berth Object name:

*****

：To change the page.

MENU：Returns to the prev.

Object information window with detail

5-24 93132801-00

Page 57

CVG-200 Chapter 5

5.4 Operation of Sounder Display

Push to display the Sounder Display.

5.4.1 Sounder Display Options

Push to bring up the Mode menus.

DISP

MODE

Basic Operation

High Frequency Mode

Usually Bottom Fixation Expansion Bottom Quality Expansion Bottom Part Expansion Part Expansion

Low Frequency Mode

Usually Bottom Fixation Expansion Bottom Quality Expansion Bottom Part Expansion Part Expansion

High and Low Frequency Mode

Usually

Bottom Part Expansion

High Frequency Mode

With the Mode menus displayed, push the button repeatedly in order to switch

Low Frequency Mode High/Low Freq. Mode

MODE

Current Detection Mode Cursor

（on highlighted row）

Move up

Move the cursor using the control knob.

in-between the various modes.

The position of the cursor indicates what is selected. Move the cursor using the control knob. Turn the knob counter-clockwise to move the cursor up the menu, and clockwise to move the cursor down the menu.

5.4.1.1 About The Modes

Down

(1) High Frequency Mode

Displays images based upon received high frequency signals. In this mode, the user can choose from the following five types of images: Normal, Bottom Fixation Expansion, Bottom Quality Expansion, Bottom Part Expansion and Part Expansion. Except for Normal and Bottom Part Expansion, each type of signal is displayed side-by-side with the Normal in a dual screen.

(2) Low Frequency Mode

Displays images based upon received low frequency signals. In this mode, the user can choose from the following five types of images: Normal, Bottom Fixation Expansion, Bottom Quality Expansion, Bottom Part Expansion and Part Expansion. Except for Normal and Bottom Part Expansion, each type of signal is displayed side-by-side with the Normal in a dual screen.

(3) High and Low Frequency Mode Displays images based upon received high and low frequency signals together. In this mode, the user can choose from following two types of images: Normal and Bottom Part Expansion.

93132801-00 5-25

Page 58

Chapter 5 CVG-200

Basic Operation

5.4.1.2 Regarding Display Images

(1) Normal

Displays from the start point of the image to the limit of the range. Generally, the bottom of the ship is the designated starting point. Utilizing the various functions (such as Shift, Draft, etc.) the user can alter the start point.

(2) Bottom Fixation Expansion

Even though the depth of the sea bottom changes, the bottom is displayed as a flat surface in order to serve as a reference. This results in being able to see small details on the sea bottom more clearly. Schools of fish in the nearby area can be monitored closely.

(3) Bottom Quality Expansion

Image Start Point

Range

Zoom range

Even though the sea bottom depth changes, the top surface of the sea bottom is displayed as a flat surface in order to serve as a reference. A range of measurement is also taken underneath the reference. This results in being able to distinguish school of fish and bottom quality that may be at the sea bottom.

(4) Bottom Part Expansion

The bottom is displayed as is, with its true shape depicted. The distance from the bottom is depicted using (solid) depth contour lines, making schools of fish near the bottom easy to see.

Quality Expansion

Normal Range

Depth contour lines

Bottom Part Expansion

5-26 93132801-00

Page 59

CVG-200 Chapter 5

(5) Part Expansion

Rather than using the sea bottom as the reference point, a mid-water Magnification Start

Basic Operation

Point is designated and the region below is

Magnification Start Point

magnified.

The zoom range is set through the value assigned in the menu. The setting chosen shall be shared by all expansion images. The zoom range is set by following the procedure below:

→

MENU MENU

”Sounder”→ ”Display”→”Zoom Range”→[Set] →

5.4.1.3 Procedures for the Sounder Display

5.4.1.3.1 Normal Display Procedure

(1) Display either the High Frequency or Low Frequency Modes using . (2) Using the control knob, choose the Normal Mode.

High Frequency Mode

Current Sounder Mode

Usually Bottom Fixation Expansion Bottom Quality Expansion Bottom Part Expansion Part Expansion

Using the control knob, choose the Normal Mode.

Down

Zoom range

MODE

5.4.1.3.2 Procedure for Displaying High and Low Frequency Mode together

Down

MODE

Low Frequency High Frequency

Low High

36.0

147

76.0

100

150

200

(1) Display High and Low Frequency Mode using . (2) Using the control knob, choose the Normal Mode.

High and Low Frequency Mode

Usually Bottom Part Expansion

Current Sounder Mode

Using the control knob, choose the Normal Mode.

100

150

200

93132801-00 5-27

Page 60

Chapter 5 CVG-200

Basic Operation

5.4.1.3.3 Procedure for Displaying Magnified High Frequencies

(1) Display High Frequency Mode using .

MODE

(2) Using the control knob, the user can choose:

Bottom Fixation Expansion, Bottom Quality Expansion, Bottom Part Expansion, and Part Expansion.

Note： Bottom Part Expansion is displayed

High Frequency

(Magnified)

ZM High

67.0

147

50 60

100

120

140

150

High Frequency

(Normal)

50.0

100

150

200

as a single screen.

5.4.1.3.4 Procedure for Displaying Magnified Low Frequencies

(1) Display Low Frequency Mode using .

MODE

(2) Using the control knob, the user can choose:

Bottom Fixation Expansion, Bottom Quality Expansion, Bottom Part Expansion, and Part Expansion.

displayed as a single screen.

Note： Bottom Part Expansion is

Low Frequency

(Magnified)

67.0

50 60

100

120

140

Low Frequency

(Normal)

Low

50.0

100

150

147

150

200

5-28 93132801-00

Page 61

CVG-200 Chapter 5

5.4.2 Range（Sounding Range）Selection

Factory Preset Ranges are as follows:

Range 1 2 3 4 5 6 7 8 m/J.fm /fm/I.fm 20 50 80 100 200 300 1000 1200 Ft. 50 160 280 360 720 1600 3600 4000

RANGE

or keys can be used to adjust the Range values.

RANGE

Simultaneously, the screen depicted below will display the Range values.

Range

50.0m

RANGE+ : 80.0m RANGE : 20.0m

While the Range display is shown, pushing the following keys shifts the Range values as listed in the display.

Current Range

Next Range value if you push: Next Range value if you push:

RANGE

Basic Operation

RANGE

Choose the Range that allows for the best view (from sea level to sea bottom).

To register a range, follow the procedure below:

→“Sounder”→“Depth Range Preset”→“Choose from Depth Range1

to 8”→[Set] →

RANGE

Or, when the “Auto Range” option has been selected, pushing the and

RANGE

buttons will bring up the following screen:

Range

uto Range

Perform the following procedure to select the automatic range mode:

→”Sounder”→ ”Sounder Menu”→”Auto Setting”→[Range] →

93132801-00 5-29

Page 62

Chapter 5 CVG-200

prop

Basic Operation

5.4.3 Adjustment of Gain and STC

Push to bring up the image adjustment menu.

High Frequency

Gain

8.8

Enhance

8.8

STC Depth

8.8

STC AMPTD

8.8

High Frequency

GAIN

Low Frequency

Gain

8.8

Enhance

8.8

STC Depth

8.8

STC AMPTD

8.8

Low Frequency

Current Frequency Setting Cursor（highlighted）

Gain value（bar display）

Enhancement value（bar display）

Enhancement value (numerical)

STC Depth Value（bar display）

STC Amplitude（bar display） STC Amplitude（numerical）

Decrease

Increase

When using the High Frequency mode, Adjustment Menu will appear. When using the Low Frequency mode, Adjustm ent Menu will appear. When using the High/Low Frequency mode, pressing the button

GAIN

Using the control knob, modify

the various values.

will alternate in-between the High and Low Frequency Adjustment Menus. The user can determine settings for the option where the cursor appears. The cursor can be moved up and down using the directional key or . The settings for the High and Low Frequency Modes can be specified totally separate from one another. Turn the control knob clockwise to increase setting values, and counter-clockwise to decrease setting values. Press the Menu button in order to close the Adjustment Menu.

High

(1) GAIN

The user can adjust the sensitivity by adjusting

43.0 50

its value.

Setting Range：

0.0 to 10.0

130

100

150

Left-hand side: example

of a weak si

nal

200

Right-hand side: example

of a

er signal

5-30 93132801-00

Page 63

CVG-200 Chapter 5

Basic Operation

When automatic gain is in operation, pressing will activate the automatic gain correction in the Adjustment Menu.

High Frequency

Auto Gain Correction

-3.0

Enhance

8.8

STC Depth

8.8

STC AMPTD

8.8

Low Frequency

Auto Gain Correction

-3.0

Enhance

8.8

STC Depth

8.8

STC AMPTD

8.8

GAIN

Auto Gain Correction (bar display) Auto Gain Correction (numerical)

High Frequency

Low Frequency

Follow the procedure below to activate Automatic Gain:

→“Sounder”→“Sounder Menu”→“Auto Gain”→[ON] →

Due to the characteristics of the sea bottom (rocky, sandy, algae, etc.), the strength of the signal may vary, resulting in varying effectiveness of the Automatic Gain Mode. When the surface of the sea bottom is not displayed as red, obtain a proper signal by adjusting the value of the Auto Gain Correction option.

Setting Range：

-10.0 to +10.0

-10.0(weak) to +10.0(strong)

(2) EMPHASIS(Enhancement)

Depending on the change in settings, the image displayed may exhibit a strong red color. Enhancement is also covered in “Image Expression” (section 6.2.2.2 of this manual).

Setting Range：

(3) STC

If the nearby waters are comparatively shallow, and there is considerable trash, plankton or other drifting material, the screen may appear reddish or yellowish. Should a school of fish be among the drifting material, distinguishing between the fish and the drifting material would prove difficult. In these situations, adjusting the STC restricts unnecessary echoes and makes it easier to identify actual schools of fish. STC can be

0.0 to 10.0

adjusted in terms of depth and amplitude.

Setting Range：

93132801-00 5-31

0.0 to 10.0

Page 64

Chapter 5 CVG-200

Basic Operation

(a) STC Depth The graph to the right depicts the change in the image below. STC Amplitude is kept at a constant.

A :Since the STC Depth value is too small, only

drifting material is removed from the image.

STC Amplitude

(Large)

B :STC Depth value is at its optimal setting.

STC Depth

C: Since the STC Depth value is too large, causing

the echoes from the fish school to be reduced too much.

(b) STC Ampl itude

The graph to the right depicts the change in the image below. STC Depth is kept at a constant.

：Since the STC Amplitude value is 0, the noise is

Adjusting STC Depth

STC Amplitude

B C

(Large)

displayed.

STC Depth

B：STC Amplitude value is at its optimal setting.

C：Since the STC Amplitude value is too large,

causing the echoes from the fish school to be reduced too much.

Adjusting STC Amplitude

Adjust the STC Depth and STC Amplitude values in order to obtain the best image.

5-32 93132801-00

Page 65

CVG-200 Chapter 5

5.4.4 Operation of the [Shift] Key

There exist 2 kinds of shifts: “Fix Shift” and “Auto Shift”.

Fix Shift： From Pre-determined depth(Shift start depth), the range is set and displayed.

Auto Shift： Should there be a sudden change is depth of the bottom engaging the Auto Shift

ensures that 30-90% of the scope of the sea bottom is displayed at all times.

5.4.4.1 Fix Shift Settings

Push to bring up the display shown below.

SHIFT

Basic Operation

Shift

OFF

Shift

0000

Down Up

Control knob adjusts the value.

Fix Shift OFF

With the Shift Setting Menu displayed, pressing will switch the Fix Shift option off or on.

With the Fix Shift option on, the user can specify the amount of shift. Pressing the directional keys left or right ( or ) moves the cursor, and the control knob sets the values. Turn the control knob right to increase the values, and left to decrease the values. While the Fix Shift option is active, the right of the display will show the following:

Fix Shift Active

SHIFT

Digit being adjusted

indicated by cursor

position (use

directional key).

Shift start depth

Range

93132801-00 5-33

Page 66

Chapter 5 CVG-200

Basic Operation

5.4.4.2 Auto Shift Settings

Displaying the Auto Shift function requires the following procedure beforehand. The procedure is as follows:

→“Sounder”→“Sounder Menu”→“Auto Setting”→[Shift]→

Push , and the Shift menu appears.

SHIFT

Shift

Auto Shift Mode

Shift

Auto Shift Mode

Shift ON

Shift OFF

Auto Shift enabled

Auto Shift disabled

Pushing switches back and forth in-between enabling and disabling the Auto Shift

SHIFT

function.

With the Auto Shift enabled, the following appears in the upper left of the screen:

High

40％ of display

90％ of display

5-34 93132801-00

Page 67

CVG-200 Chapter 5

5.4.5 Operation of Variable Range Markers (VRM)

The Variable Range Markers (VRM) enable for the operation of the Sounder screen. The VRM allow for moving up and down within the screen. Matching up the schools of fish with the depth markers indicate their depth. The VRMs are green and yellow. Push and the user can alternate operations. When Part Expansion is done, the green VRM is utilized at the part expansion starting depth.

(Refer to section 5.4.7)

Basic Operation

VRM

5.4.5.1 Normal Image Mode

Push .

With the previous operation, the (green or yellow) VRM in operation shall have their values displayed in reverse display (white with a black surrounding block). Move up or down using the control knob.

As the VRM is moved up or down, the numerical value and depth are displayed.

With the numerical values reversed, push .

VRM can be changed within operational parameters.

VRM

Move up

Move down

VRM

High

43.0

130

43.0

100

150

200

Numerical values displayed in reverse display.

100

130

150

200

Caution: As a VRM operation finishes, returning to the prior numerical value

becomes impossible after 5 seconds. To begin operations once again, press .

93132801-00 5-35

VRM

Page 68

Chapter 5 CVG-200

Basic Operation

5.4.5.2 Combined Imaging

5.4.5.2.1 Vertical Partitioning

(1) Dual Frequency mode

Push .

VRM

Turn over the numerical value displayed. The VRM is displayed across the entire screen. Move up or down using the control knob.

Move up

Move down

As the VRM moves, the numerical value displayed changes accordingly.

With the numerical value reversed, press the VRM button.

VRM

Low High

43.0

130

Low High

43.0

100

150

200

100

150

200

VRM color can be changed.

130

100

150

200

100

150

200

5-36 93132801-00

Page 69

CVG-200 Chapter 5

(2) Normal/ Expansion mode

Push .

The numerical value turns over. A VRM appears on one side of the partitioned screen.

VRM

67.0

50 60

High

Basic Operation

Move up or down using the control knob.

Move up

Move down

As the VRM moves, the numerical value displayed changes accordingly.

Push the directional button left , and the display of the numerical value moves the VRM over to the left side of the display.

Push the directional button right , and the display of the numerical value moves the VRM over to the right side of the display.

67.0

114

100

120

140

50 60

100

120

130

High

100

150

200

100

150

140

150

200

93132801-00 5-37

Page 70

Chapter 5 CVG-200

Basic Operation

5.4.5.2.2 Horizontal Partitioning

(1)Dual Frequency mode

Push .

VRM

High

95.0

Numerical value display turns over. The VRM stretches across the entire width of the screen.

Move up or down using the control knob.

Low

40.0

Move up

Move down

130

The VRM may move beyond the partition mark. In these cases, the depth values become the depth values for the display depicted here.

As the VRM moves, the numerical value displayed changes accordingly.

(2) Normal/ Magnified mode

100

Move from upper screen to lower screen

200

100

200

Partition Mark

Push .

VRM

High

95.0

Numerical value display turns over. The VRM stretches across the entire width of the screen.

Move up or down using the control knob.

Move up

Move down

BTM

8.5

4.0

The VRM may move beyond the partition mark. In these cases, the depth values become the depth values for the display depicted here.

As the VRM moves, the numerical value displayed changes accordingly.

100

Move from upper screen to lower screen

200

Partition Mark

5-38 93132801-00

Page 71

CVG-200 Chapter 5

5.4.6 Setting Positions for Part Expansion mode

5.4.6.1 Vertical Partitioning

(1) Push and select Part Expansion of High (or Low) Frequency Mode.

(2) Set the zoom range.

(3) Push and turn over the numerical display of the Green Marker.

MODE

(Refer to Sounder Imaging Display Procedure, section 5.4.1.3.)

(Refer to Imaging, section 5.4.1.2.)

VRM

(To change the numerical display of the Yellow Marker, push

VRM

once again.)

8.5

Basic Operation

Green Marker

Zoom Mark

Operate the Green Marker by the Control knob, and set the upper depth of the zoom range.

In the right figure, the high (or low) frequency normal imaging is on the right-hand side, and the left-hand side displays the part expansion image. The position of the magnification pictured here is 50, while the zoom range is set at 20.

ZM High

Yellow Marker

50.0

170

100

150

200

Zoom range

93132801-00 5-39

Page 72

Chapter 5 CVG-200

Basic Operation

5.4.6.2 Horizontal Partitioning

(1) Push and select Part Expansion of High (or Low) Frequency Mode.

(2) Set the zoom range.

(3) Push and turn over the numerical display of the Green Marker.

MODE

(Refer to Sounder Imaging Display Procedure, section 5.4.1.3.)

(Please refer to Imaging, section 5.4.1.2.)

VRM

(To change the numerical display of the Yellow Marker, push once again. )

VRM

Green Marker

Zoom Mark

Operate the Green Marker by the Control knob, and set the upper depth of the zoom range.

In the right figure, the high (or low) frequency normal imaging is on the upper side, and the lower side displays the part expansion image. The position of the magnification pictured here is 50, while the zoom range is set at 20.

High

50.0

170

Yellow Marker

100

200

Zoom Range

5-40 93132801-00

Page 73

CVG-200 Chapter 6

Using the Menu

Chapter 6

Chapter 6 Using the Menu

Page No.

6.1 Menu functions................................................................................................6-1

6.1.1 Menu Operation....................................................................................................................... 6-1

6.1.2 Choosing Menus...................................................................................................................... 6-2

6.1.3 Menu Table .............................................................................................................................. 6-3

6.1.3.1 Sounder Menu ................................................................................................................... 6-3

6.1.3.2 Plotter Menu Functions...................................................................................................... 6-5

6.1.3.3 ETC. Menu ........................................................................................................................... 6-9

6.2 Sounder Menu ................................................................................................6-11

6.2.1 Transmission ..........................................................................................................................6-11

6.2.1.1 Pulse Width(H), Pulse Width(L)........................................................................................6-11

6.2.1.2 Output ...............................................................................................................................6-11

6.2.1.3 PRR (Pulse Repetition Rate)............................................................................................6-11

6.2.2 Image..................................................................................................................................... 6-12

6.2.2.1 Interference Rejection...................................................................................................... 6-12

6.2.2.2 Noise Rejection / EM ....................................................................................................... 6-12

6.2.2.2.1 Enhance.......................................................................................................................6-12

6.2.2.3 White Line........................................................................................................................6-12

6.2.2.4 Color Tone........................................................................................................................ 6-12

6.2.2.5 Background Color............................................................................................................ 6-13

6.2.2.6 Color Rejection ................................................................................................................ 6-13

6.2.3 Display................................................................................................................................... 6-13

6.2.3.1 A-Scope............................................................................................................................ 6-13

6.2.3.2 Zoom Range....................................................................................................................6-14

6.2.3.3 Depth Display Size........................................................................................................... 6-14

6.2.3.4 Depth Value Position........................................................................................................ 6-14

6.2.3.5 Scale................................................................................................................................6-15

6.2.3.6 Scale Position .................................................................................................................. 6-15

6.2.3.7 Scale V alue...................................................................................................................... 6-15

6.2.3.8 Time Mark........................................................................................................................6-15

6.2.3.9 Image Speed.................................................................................................................... 6-16

6.2.3.10 Image Direction.............................................................................................................. 6-16

6.2.3.11 Image Partition...............................................................................................................6-16

6.2.3.12 Image Swap................................................................................................................... 6-16

6.2.3.13 Color Bar Scale.............................................................................................................. 6-17

6.2.3.14 Water Temp Display....................................................................................................... 6-17

6.2.3.15 Water Temp Graph......................................................................................................... 6-17

6.2.4 Automatic............................................................................................................................... 6-18

6.2.4.1 Auto Setting...................................................................................................................... 6-18

6.2.4.2 Auto Gain ......................................................................................................................... 6-18

6.2.5 Depth Range Preset.............................................................................................................. 6-19

6.2.5.1 Depth Range1 to 8........................................................................................................... 6-19

6.2.6 System Setting ...................................................................................................................... 6-19

6.2.6.1 Depth Unit........................................................................................................................6-19

6.2.6.2 Draft Setting.....................................................................................................................6-19

6.2.6.3 Bottom Start.....................................................................................................................6-20

6.2.6.4 Bottom Detection ............................................................................................................. 6-20

6.2.6.5 Depth Measurement ........................................................................................................ 6-20

6.2.6.6 Sonic Correction .......................................................................................................

6.2.6.7 Water Temperature Correction......................................................................................... 6-20

6.2.6.8 Boat Speed Correction..................................................................................................... 6-21

6.2.6.9 Water Temperature Data..................................................................................................6-21

6.2.6.10 EXT Trigger Type........................................................................................................... 6-21

....... 6-20

93132802-02 Contents

Page 74

Chapter 6 CVG-200

Using the Menu

6.2.7 Bottom Detection Adjust.........................................................................................................6-21

6.2.7.1 High Frequency, Low Frequency......................................................................................6-21

6.3 Plotter Menu.................................................................................................. 6-22

6.3.1 Mark Block Number ...............................................................................................................6-22

6.3.2 Display Settings.....................................................................................................................6-22

6.3.2.1 Position Data Display.......................................................................................................6-22

6.3.2.1.1 L / L.............................................................................................................................6-22

6.3.2.1.2 LORAN C ....................................................................................................................6-22

6.3.2.1.3 DECCA........................................................................................................................6-23

6.3.2.2 Chart Display....................................................................................................................6-23

6.3.2.2.1 Ocean Color.................................................................................................................6-23

6.3.2.2.2 land Color....................................................................................................................6-23

6.3.2.2.3 Boundlines...................................................................................................................6-23

6.3.2.2.4 Grid.............................................................................................................................6-23

6.3.2.2.5 Place Name.................................................................................................................6-23

6.3.2.2.6 Lake & River ................................................................................................................6-24

6.3.2.2.7 Cultural Features..........................................................................................................6-24

6.3.2.2.8 Landmarks...................................................................................................................6-24

6.3.2.2.9 Ports ...........................................................................................................................6-24

6.3.2.2.10 Caution Area..............................................................................................................6-24

6.3.2.2.11 Lighthouse .................................................................................................................6-24

6.3.2.2.12 Buoys........................................................................................................................6-24

6.3.2.2.13 Signals ......................................................................................................................6-24

6.3.2.2.14 Track & Routes...........................................................................................................6-24

6.3.2.2.15 Tideways....................................................................................................................6-25

6.3.2.2.16 Soundings..................................................................................................................6-25

6.3.2.2.17 Seabed......................................................................................................................6-25

6.3.2.2.18 Depth Contour............................................................................................................6-25

6.3.2.2.19 Depth Unit..................................................................................................................6-25

6.3.2.2.20 Object Item ................................................................................................................6-25

6.3.2.3 Screen Display Setting.....................................................................................................6-26

6.3.2.3.1 Course Line .................................................................................................................6-26

6.3.2.3.2 Course Display.............................................................................................................6-26

6.3.2.3.3 Position Mark ...............................................................................................................6-26

6.3.2.3.4 Track Line....................................................................................................................6-26

6.3.2.3.5 Mark Size ....................................................................................................................6-26

6.3.2.3.6 Cursor Type.................................................................................................................6-27

6.3.2.3.7 Info Window.................................................................................................................6-27

6.3.2.3.8 Position Info Window.....................................................................................................6-27

6.3.2.3.9 Ring Marker ............................................................................................................................6-27

6.3.2.3.10 Map Rotation Speed

6.3.3 NAV........................................................................................................................................6-28

6.3.4 Mark Edit................................................................................................................................6-28

6.3.4.1 Edit ...................................................................................................................................6-28

6.3.4.2 Transfer............................................................................................................................6-29

6.3.4.3 Delete...............................................................................................................................6-29

6.3.4.4 Operation Of Blocks.........................................................................................................6-29

6.3.4.4.1 Display of Blocks..........................................................................................................6-29

6.3.4.4.2 Transfer of Blocks.........................................................................................................6-29

6.3.4.4.3 Erase of Blocks ............................................................................................................6-29

6.3.5 Route......................................................................................................................................6-30

6.3.5.1 Routing.............................................................................................................................6-30

6.3.5.1.1 Cursor .........................................................................................................................6-30

6.3.5.1.2 Value...........................................................................................................................6-30

6.3.5.2 Route Erase .....................................................................................................................6-31

6.3.5.2.1 Cursor .........................................................................................................................6-31

6.3.5.2.2 Value...........................................................................................................................6-31

6.3.5.3 Route Edit ........................................................................................................................6-32

6.3.5.3.1 Cursor .........................................................................................................................6-32

...................................................................................................6-27

Contents 93132802-02

Page 75

CVG-200 Chapter 6

Using the Menu

6.3.5.3.1.1 Waypoint Movement................................................................................................ 6-32

6.3.5.3.1.2 Waypoint Addition...................................................................................................6-32

6.3.5.3.1.3 Waypoint Erase ...................................................................................................... 6-33

6.3.5.3.2 Value ............................................................................................................................. 6-33

6.3.5.3.2.1 Waypoint Movement................................................................................................ 6-33

6.3.5.3.2.2 Waypoint Addition ................................................................................................... 6-33

6.3.5.3.2.3 Waypoint Erase ...................................................................................................... 6-34

6.3.5.3.2.4 Comment Edit ........................................................................................................ 6-34

6.3.6 Track Store............................................................................................................................ 6-34

6.3.7 Track Recall........................................................................................................................... 6-34

6.3.8 Track Color............................................................................................................................ 6-35

6.3.8.1 Soundings Response....................................................................................................... 6-35

6.3.8.2 Water Temperature Response.........................................................................................6-35

6.3.9 Drawing ................................................................................................................................. 6-35

6.3.9.1 Drawing Block.................................................................................................................. 6-35

6.3.9.2 Drawing Line Thickness................................................................................................... 6-35

6.3.9.3 Input Method........................................................................................................... .........6-35

6.3.9.3.1 Cursor Input.............................................................................................................. 6-36

6.3.9.3.2 Value Input................................................................................................................ 6-36

6.3.10 Drawing Edit........................................................................................................................6-37

6.3.10.1 Cursor............................................................................................................................6-37

6.3.10.1.1 Movement...............................................................................................................6-37

6.3.10.1.2 Addition................................................................................................................... 6-37

6.3.10.1.3 Erase...................................................................................................................... 6-37

6.3.10.2 Value.............................................................................................................................. 6-38

6.3.10.2.1 Movement............................................................................................................... 6-38

6.3.10.2.2 Addition .................................................................................................................. 6-38

6.3.10.2.3 Erase...................................................................................................................... 6-38

6.3.11 Drawing Erase ..................................................................................................................... 6-36

6.3.12 Drawing Recall .................................................................................................................... 6-38

6.3.13 System Setting ....................................................................................................................6-38

6.3.13.1 Distance/Speed.............................................................................................................. 6-38

6.3.13.2 Plot Interval....................................................................................................................6-39

6.3.13.2.1 Time Interval............................................................................................................ 6-39

6.3.13.2.2 Distance Interval...................................................................................................... 6-39

6.3.13.3 Number of Plot............................................................................................................... 6-39

6.3.13.4 Average Speed............................................................................................................... 6-39

6.3.13.4.1 Average Number......................................................................................................6-39

6.3.13.5 Fix Scale 1, 2, 3............................................................................................................. 6-40

6.3.13.6 Auto Scroll...................................................................................................................... 6-40

6.3.13.7 Scroll Direction............................................................................................................... 6-40

6.3.13.8 Event Store.................................................................................................................... 6-40

6.3.13.9 Correction ......................................................................................................................6-40

6.3.13.9.1 Correction Start ....................................................................................................... 6-41

6.3.13.10 Compass Correction....................................................................................................6-41

6.3.13.11 Local Time Correction..................................................................................................6-41

6.3.13.12 Navigation Mode.......................................................................................................... 6-41

6.3.14 Other Ship Track.................................................................................................................. 6-42

6.3.14.1 Ship Mark....................................................................................................................... 6-42

6.3.14.2 Mark...............................................................................................................................6-42

6.3.14.3 ID Number...................................................................................................................... 6-42

6.3.14.4 Track Display ................................................................................................................. 6-42

6.3.14.5 Track Line ...................................................................................................................... 6-42

6.3.14.6 Color............................................................................................................................... 6-42

6.3.14.7 Plot Limit ........................................................................................................................ 6-42

6.3.14.8 Course Line.................................................................................................................... 6-42

6.3.15 Geodesic Line...................................................................................................................... 6-43

6.3.16 Draw Parallel Lines.............................................................................................................. 6-43

6.3.16.1 Position..........................................................................................................................6-43

93132802-02 Contents

Page 76

Chapter 6 CVG-200

Using the Menu

6.3.16.2 Direction.........................................................................................................................6-43

6.3.16.3 Line Length.....................................................................................................................6-43

6.3.16.4 Line Interval....................................................................................................................6-43

6.3.16.5 Line Number...................................................................................................................6-44

6.3.16.6 Base Point......................................................................................................................6-44

6.3.16.7 Altering Settings of Parallel Li ne Drawings without Menus............................................6-44

6.4 Settings of Other Menus (ETC).................................................................... 6-45

6.4.1 GPS/DGPS setting (KODEN products only)..........................................................................6-45

6.4.2 GPS Monitor ..........................................................................................................................6-45

6.4.3 User C-Card...........................................................................................................................6-45

6.4.3.1 Store.................................................................................................................................6-46

6.4.3.1.1 Store Mark.................................................................................................................6-46

6.4.3.1.2 Store Route...............................................................................................................6-46

6.4.3.1.3 Store Track................................................................................................................6-46

6.4.3.1.4 Store Drawing............................................................................................................6-46

6.4.3.1.5 Store Other Ship Tracks..............................................................................................6-46

6.4.3.1.6 Store System.............................................................................................................6-46

6.4.3.2 Recall................................................................................................................................6-46

6.4.3.2.1 Recall Mark ...............................................................................................................6-46

6.4.3.2.2 Recall Route..............................................................................................................6-46

6.4.3.2.3 Recall Track ..............................................................................................................6-46

6.4.3.2.4 Recall Drawing ..........................................................................................................6-46

6.4.3.2.5 Recall Other Ship Track..............................................................................................6-47

6.4.3.2.6 Recall System............................................................................................................6-47

6.4.3.3 Erase................................................................................................................................6-47

6.4.3.3.1 Erase Mark................................................................................................................6-47

6.4.3.3.2 Erase Route ..............................................................................................................6-47

6.4.3.3.3 Erase Track...............................................................................................................6-47

6.4.3.3.4 Erase Drawing...........................................................................................................6-47

6.4.3.3.5 Erase Other Ship Track...............................................................................................6-47

6.4.3.3.6 Erase System data.....................................................................................................6-47

6.4.3.4 Format..............................................................................................................................6-47

6.4.4 Screen Display Registration ..................................................................................................6-48

6.4.5 Alarm......................................................................................................................................6-49

6.4.5.1 Depth Alarm......................................................................................................................6-49

6.4.5.2 Fish Alarm ........................................................................................................................6-49

6.4.5.3 Arrival Alarm.....................................................................................................................6-50

6.4.5.4 POB (Person Over Board) Alarm.....................................................................................6-50

6.4.5.5 XTE (Cross Track Error) Alarm ........................................................................................6-50

6.4.5.6 Alarm Zone.......................................................................................................................6-50

6.4.6 Language...............................................................................................................................6-50

6.4.7 Maintenance ..........................................................................................................................6-51

6.4.7.1 Simulation.........................................................................................................................6-51

6.4.7.2 System Test......................................................................................................................6-51

6.4.7.3 Color Palette Operation....................................................................................................6-51

6.4.7.4 Data Communication........................................................................................................6-51

6.4.7.5 Flash ROM Erase.............................................................................................................6-51

6.4.7.6 Format..............................................................................................................................6-51

Contents 93132802-02

Page 77

CVG-200 Chapter 6

Using the Menu

Chapter 6 Using the Menu

6.1 Menu functions

The main menu has three categories: Sounder, Plotter, and “etc.” (others). From these categories, other sub-menus and categories shall appear. These sub-menus are explained from page 6-3 onward.

Press

Main Menu display

Sounder Plotter

etc

6.1.1 Menu Operation

Press the menu key, and the menu window (main menu) shall appear. The directional key and the control knob can adjust numerical values as well as move the cursor.

Hint: Pay attention to where the cursor is

Sounder Plotter

Press

etc

The cursor appears in the same place where it was during the window’s last session. In this example, the cursor appears over “Etc.” since that is where it was last time.

SHIFT

GAIN

VRM

RANGE

MODE

MARK

COLOR

TRACK COLOR

FIX

ERASE

TRACK ERASE

ROUTE

CURS

Control knob

Directional key

TRACK

ON/OFF

GOTO POB

Menu key

CANCEL

ENT

CLR MENU INFO

POWER

BRT DISP

Figure 6.1 Operation Panel

93132802-02 6-1

Page 78

Chapter 6 CVG-200

Using the Menu

6.1.2 Choosing Menus

[ Example of Choosing a Menu ]

(3) (3)

This action returns to the previous/main menu of the sub-menu. Doing this to the main menu shall cause the menu window to disappear altogether.

(1)

(2) (2) (2)

The cursor moves down corresponding to the number of times the down key is pressed.

The sub-menu of the highlighted option (where the cursor is) shall also appear.

The cursor moves up corresponding to the number of times the up key is pressed.

Pushing left or right causes the selected value to change.

Turning the control knob alters the selected value.

Note: The operations listed below may not apply to all menus. Please pay attention to any messages that may appear in each menu.

[ Example of using keys ]

(1) ：Press to the right.

(2) OR

Press either the menu key or the left directional key.

(3)

(This shall return the user to the previous/main menu.)

6-2 93132802-02

as well as pressing the up and down keys shall move the cursor and confirm the selected value for that category.

Page 79

CVG-200 Chapter 6

Using the Menu

6.1.3 Menu Table

6.1.3.1 Sounder Menu

Sounder Menu Setting Menu Setting Range

Transmission

Image

Display

Automatic

Pulse Width (H) Super short, Short, Middle,

Long

Pulse Width (L) Super short, Short, Middle,

Long Output Normal, Low PRF 1 to 10 Interference rejection OFF, 1, 2 Noise Rejection/EM Noise Rejection, Enhance

Mode Enhance 25, 35, 45, 55, 65 White line OFF, 1 to 5, Auto Color tone 1 to 3 Background color 1 to 9

Reject specified colors from Color rejection

Ａ scope Zoom range

Depth value size OFF, Small, Middle, Large

Depth value position Bottom, top

Scale OFF, Single, All Scale position Side, Center Scale value Small, Large Time mark OFF, 10 sec, 1min

Image speed Image direction

Image partition , Image swap A|B, B|A Color bar scale OFF, ON Water temp display

Water temp graph OFF, ON Auto setting OFF, Range, Shift

the Sounder Image.

(Replaces the background

color)

OFF, Small, Large

2.5 to 200 (m, fm, I.fm, J.fm)

10 to 650 (ft)

4/1, 3/1, 2/1, 1/1,

Stop, 1/2, 1/3, 1/4,

1/6, 1/8, 1/12, 1/16

←｜←, ←｜→

OFF, ℃,

ﾟ

93132802-02 6-3

Auto gain OFF, ON

Page 80

Chapter 6 CVG-200

Using the Menu

Sounder Menu Menu Setting Range Depth range preset

System setting

Bottom detection Adjust

Depth range 1 Refer to 6.2.5.1 Depth range 2

Depth range 3 Depth range 4 Depth range 5 Depth range 6 Depth range 7 Depth range 8 Depth unit Draft setting 0.0 to 25.5(ft: 00 to 85.0)

Bottom start 0.0 to 20.0(ft: 00 to 65.0) Bottom detection Inside range

Depth measurement Auto, High freq., Low freq. Sonic correction

Water temp correction -10.0 to +10.0 Boat speed correction -10.0 to +10.0 Water temp data INT, EXT EXT trigger type OFF, , High frequency -80 to +40

Low frequency -80 to +40

〃〃〃〃〃〃〃

ｍ, J.fm, fm, I.fm, ft

(in-screen) Outside range (off-screen)

-7 to +2％

Note: (H)：High frequency (L)：Low frequency

6-4 93132802-02

Page 81

CVG-200 Chapter 6

Using the Menu

6.1.3.2 Plotter Menu Functions

Plotter Menu Sub Menu 1 Sub Menu 2 Setting Range Mark Block Number

Display Setting

NAV

00000, 00100, 01000,

02000, 03000, 04000, 05000, 06000, 07000, 08000

Position data display LORAN C DECCA Chart display Ocean color Choose from among 4 colors Land color Choose from among 4 colors Boundlines ON, OFF

Grid ON, OFF Place name ON, OFF Lake & River ON, OFF Cultural features ON, OFF Landmarks ON, OFF Ports ON, OFF Cautionarea ON, OFF Lighthouse ON, OFF Buoys ON, OFF Signals ON, OFF Track & Routes ON, OFF Tideways ON, OFF Soundings ON, OFF Seabed ON, OFF Depth Contour ON, OFF Depth unit m, fm, D.fm, ft Objection Item Details, Simple Screen Course line Long Line, SPD RESP, OFF Display Course display True, Magnetic Setting Position mark Large Circle, Small Circle, Dot,

Track line Thick, Thin Mark size Large, Small Cursor type Standard, Long Line

Position info window Large, Small, OFF Ring marker OFF, ON Map rotation speed High Speed, Low Speed North Up, East Up, South Up, West

L/L

Ship (Large), Ship(Small)

Info window OFF, L/L, DPT/W_TEMP,

TIME/ETA, Speed

Up, Course Up, Head Up, Own Ship Center Fix Mode

93132802-02 6-5

Page 82

Chapter 6 CVG-200

Using the Menu

Plotter Menu Sub Menu 1 Sub Menu 2 Setting Range

Mark Edit

Route

Track Store Track Recall Track Color

Drawing

Drawing Edit

Drawing Erase Drawing Recall

Edit Transfer Delete Operation of blocks

Routing Cursor Value Route erase Cursor Value Route edit Cursor Value 1, 2, 3, 4, 5, 6, 7 1, 2, 3, 4, 5, 6, 7 Normal Depth RESP Green, Red, Yellow, Deep

W_Temp RESP Green, Red, Yellow, Deep Drawing block 1, 2, 3, 4, 5, 6, 7

Drawing Line Thickness Input method Cursor, Value Cursor

Value Drawing block 1 Drawing block 2 Drawing block 3 Drawing block 4 Drawing block 5 Drawing block 6 Drawing block 7

Block 1 DISP YES, NO Block 2 DISP YES, NO Block 3 DISP YES, NO Block 4 DISP YES, NO Block 5 DISP YES, NO Block 6 DISP YES, NO Block 7 DISP YES, NO

Display of blocks Transfer of blocks Erase of blocks

Blue, Blue, Pink, White Blue, Blue, Pink, White

Thin, Thick

6-6 93132802-02

Page 83

CVG-200 Chapter 6

Using the Menu

Plotter Menu Sub Menu 1 Sub Menu 2 Setting Range

System Setting

Other Ship Track

Distance/Speed nm, kt km, km/h Plot interval Time, Distance Time interval 1, 2, 5, 10, 20, 30,

60, 120, 300, 600 (second)

Distance interval 0.01, 0.02, 0.05,

0.10, 0.20, 0.50,

1.00, 2.00, 5.00,

10.00(nm/km) Number of plot 2000, 4000, 7000 Average speed ON, OFF Average number 1 to 60 Fix scale １

Fix scale １ Fix scale １ Auto scroll Screen Edge,

Scroll direction View Point, Chart Event store OFF, 0 to 99 Correction ON, OFF Correction Start Compass correction -90.0 to +90.0 Local time correction -13.5 to +13.5 Navigation mode Rhumb Line

Other ship 0

Other ship 1 Same as other ship 0 Same as other ship 0 Other ship 2 Same as other ship 0 Same as other ship 0 Other ship 3 Same as other ship 0 Same as other ship 0 Other ship 4 Same as other ship 0 Same as other ship 0 Other ship 5 Same as other ship 0 Same as other ship 0 Other ship 6 Same as other ship 0 Same as other ship 0 Other ship 7 Same as other ship 0 Same as other ship 0 Other ship 8 Same as other ship 0 Same as other ship 0 Other ship 9 Same as other ship 0 Same as other ship 0

Within Screen

Great Circuit

Ship mark Marl L_Circle, S_Circle, Dot

ID No. ON, OFF Track display ON, OFF Track line Thin, Thick Color Choose from among 7

Plot limit 50, 100, 200, Course line SPD RESP, OFF

ON、OFF

colors 500, 1000

93132802-02 6-7

Page 84

Chapter 6 CVG-200

Using the Menu

Plotter Menu Sub Menu 1 Sub Menu 2 Setting Range

Geodesic Line

Draw Parallel Lines

Start position

End position

Start position

Direction Line length 0.1 to 999.9

Line interval 0.001 to 9.999 Line number 1 to 99 Base point Left, Center, Light

0 ﾟ 00.000N to 90 ﾟ 00.000N, 0 ﾟ 00.000S to 90 ﾟ 00.000S 0 ﾟ 00.000E to 180 ﾟ 00.000E, 0 ﾟ 00.000W to 180 ﾟ 00.000W

Invalid、Valid 0 ﾟ 00.000N to 90 ﾟ 00.000N,

0 ﾟ 00.000S to 90 ﾟ 00.000S 0 ﾟ 00.000E to 180 ﾟ 00.000E, 0 ﾟ 00.000W to 180 ﾟ 00.000W

0.0 to 359.9（°）

6-8 93132802-02

Page 85

CVG-200 Chapter 6

Using the Menu

6.1.3.3 ETC. Menu

etc. Menu Sub Menu 1 Sub Menu 2 Setting Range

GPS/DGPS Setting

GPS Monitor User C-Card

Screen Display Registration Alarm

Language

Datum TOKYO, WGS-84 Average 1 to 3 DGPS mode OFF, BEACON, SBAS

Beacon select

Frequency 283.5 to 325.0 Baud rate 50, 100, 200

GPS INIT NO, YES

Store Mark, Route, Track,

Recall Mark, Route, Track,

Erase Mark, Route, Track,

Format Register displays in use

Depth alarm Alarm settings OFF, ON Upper alarm 0 to 3000(m),

Lower alarm 0 to 3000(m), Fish alarm Alarm settings OFF, ON

Upper alarm 0 to 3000(m), Lower alarm 0 to 3000(m), Alarm length Short, Middle, Long

Upper color Choose from among 15 Lower color Choose from among 15 Arrival alarm Alarm settings OFF, ON

Alarm range 0.05 to 5.00(unit) POB alarm Alarm settings OFF, ON Alarm range 0.05 to 5.00(unit) XTE alarm Alarm settings OFF, ON Alarm range 0.05 to 5.00(unit) Alarm Zone Zone settings OFF, ON English

AUTO, MANUAL

Drawing, Other Ship Track, System

from 12 types

0 to 6000(ft) 0 to 6000(ft)

colors for upper positions colors for lower positions

Japanese Spanish French

93132802-02 6-9

Page 86

Chapter 6 CVG-200

Using the Menu

etc Menu Sub Menu 1 Sub Menu 2 Setting Range

Maintenance

Simulation Sounder OFF, ON Plotter OFF, ON Start LAT

Start LON

Speed 0 to 50(kt) Steering

Course Mode Normal, WPT,

System test LCD test RAM test Key test Brightness COM port test CH0, CH1, CH2, CH3 Buzzer test High Tone Test,

System information Color palette

Operation

Data Communication Flash ROM erase

Format Sounder, Plotter,

Set color palette (ranging

00 ﾟ 00.000 to 90 ﾟ 00.000N, 00 ﾟ 00.000 to 90 ﾟ 00.000S 000 ﾟ 00.000 to 180 ﾟ 00.000E, 000 ﾟ 00.000 to 180 ﾟ 00.000W

0 to 359(°) 0 to 359(°)

Type A, T ype B

Low Tone Test

from Palette No. 1-254 (red/blue/green)) for Sounder Image. Each palette contains 255 colors.

COLOR PALETTE

6-10 93132802-02

Page 87

CVG-200 Chapter 6

Using the Menu

6.2 Sounder Menu

6.2.1 Transmission

6.2.1.1 Pulse Width(H), Pulse Width(L)

Choose from 4 pulse widths: super short, short, middle, long

Selection: Super Short, Short, Middle, Long

Resolution and detectable depth of a sounder varies depending on the pulse width.

Super Short: Image resolution is very good but detectable depth is extremely shortened. Short: Image resolution is good but detectable depth is shortened. Middle: Image resolution and detectable depth are improved compared with the Short Long: Image resolution is poor but detectable depth is lengthened.

6.2.1.2 Output

Output reduction can be induced on high and low frequencies. Selection: Normal, Low

Choosing the “low” option will reduce output and enables various inspections to be carried out during maintenance.

6.2.1.3 PRR (Pulse Repetition Rate)

The Pulse Repetition Rate can be set for each range. Setting Range: 1(Normal) to 10(Slowest)

Using this function, you can eliminate the false echoes caused by other sounder’s transmission working on nearly the same PRR.

False echoes produced by transmission from other sounder

93132802-02 6-11

Real echoes of bottom

Setting value

2→10

Real echoes of fish school

Page 88

Chapter 6 CVG-200

Using the Menu

6.2.2 Image

6.2.2.1 Interference Rejection

Image interference from other boats can be removed through this

００

function. Selection: OFF, 1(Weak), 2(Strong)

Based on the level of interference, choose either weak or strong levels of Interference Rejection.

6.2.2.2 Noise Rejection / Enhance (EM)

This function selects whether to use the noise rejection mode or the enha nce mode. (Refer to 5.4.3 Adjustment of Gain and S TC)

Selection: Noise Rejection, Enhance mode

Only when noise rejection is selected, “Enhance” can be changed.

6.2.2.2.1 Enhance

Enhances the picture presentation by changing the dynamic range of sonar video. Setting Range: 25db, 35db, 45db, 55db, 65db

Interference from other ship

11550

OFF Weak Strong

５５００

１１００００

１１５５００

２２００００

As the values increase, the image can become more detailed. As the values decrease, the image becomes more less detailed.

6.2.2.3 White Line

The white line is drawn on the edge of the seabed echo. Setting Range: OFF, 1, 2, 3, 4, 5, Auto

OFF: White line not displayed 1(Thin) to 5(Thick) Automatic: The seabed (displayed in red) is about half

the thickness of the displayed white line. Images of school of fish near the seabed can be distinguished.

6.2.2.4 Color Tone

Select color tone. Selection: 1, 2, 3(3 steps)

White line

6-12 93132802-02

Page 89

CVG-200 Chapter 6

Using the Menu

6.2.2.5 Background Color

Select background color . Setting Range: 1 to 9

1: Pale Blue 2: Marine Blue 3: Blue 4: Dark Blue 5: Black 6: Pale Greenish Blue 7: Greenish Blue 8: Dark Blue 9: White

This functions to make the image easier to see.

6.2.2.6 Color Rejection

Specified image col ors can be made into the background color.

Setting Range:1 to 15

This functions to limit colors, making schools of fish easier to see.

6.2.3 Display

6.2.3.1 A Scope

Select A-scope display. Setting Range: OFF, Small, Large

The most current images are displayed in real-time using A-Scope, thus functioning to reveal where schools of fish may be as soon as possible.

※ If the vertically partitioned screen is displaying

objects in the following fashion “←｜→”, the A-Scope does not display.

Single Display

Dual Display

Image direction

Position of the A-scope

93132802-02 6-13

Page 90

Chapter 6 CVG-200

Using the Menu

6.2.3.2 Zoom Range

Selection of zoom ranging for Bottom Fixation Expansion, Bottom Quality Expansion, Bottom Part Expansion and Part Expansion can be done in this function.

※ The same zoom range is utilized to each type of magnification display.

Setting Range:

m, J.fm, fm, I.fm:

2.5, 5, 7.5, 10, 15, 20, 25, 30, 35, 40, 45, 50, 55, 60, 70, 80, 90, 100, 110, 120, 130, 140, 150, 160, 180, 200

ft:

10, 15, 20, 30, 40, 50, 60, 80, 100, 120, 140, 160, 180, 200, 220, 240, 260, 280, 320, 360, 400, 450, 500, 550, 600, 650

Zoom/Normal

Functions to magnify the set range.

6.2.3.3 Depth Display Size

This function selects Depth value/OFF or when ON, size of charact ers displayed. Selection: OFF, Small, Middle, Large

OFF: Depth value not displayed.

This functions to control the display of the water depth on the sounder screen.

6.2.3.4 Depth Value Position

Select the position of depth value. Selection: Bottom, Top

Zoom range is specified by the orange bar on the right-hand side of the normal screen.

Top: Water depth displayed on the upper left part of the sounder display. Bottom: Water depth displayed on the lowe r left part of the sounder display.

6-14 93132802-02

Page 91

CVG-200 Chapter 6

Using the Menu

6.2.3.5 Scale

This determines the settings for whether or not to display the scale. Selection: OFF, Single, All

OFF: Scale not displayed Single:・In dual frequency mode, the scale is displayed on the

right-hand side screen.

・When displaying in horizontal partitioning, determines settings

for displaying the scale in other modes.

All:・In the dual frequency mode, the scale is displayed on the right-hand side of both

screens.

・When displaying in horizontal partitioning, determines settings for displaying the

scale in other modes.

6.2.3.6 Scale Position

Sets the display position of the scale. Selection: Side, Center

Side: Sets the display position of the scale to the right-hand side of the screen. Center: Sets the display position of the scale to the center of the screen.

Dual display

ertically split screen

6.2.3.7 Scale Value

Selects the size of the scale value. Selection: Small, Large

Small: Small character size Large: Large character size

6.2.3.8 Time Mark

Selects the time mark ON or OFF or time unit (every 10 seconds, 1 min). Selection: OFF, 10 sec, 1min

OFF: time marks not displayed 10 sec: Every 5 seconds, white (or green) and black

marks are shown to show the passage of time.

1min: Every 30 seconds white (or green) and black

marks are shown to show the passage of time.

Time unit

Time mark

Time mark direction

Image direction

Sounder screen

Time marks show the passage of time, and are displayed in the same direction as the image and speed. When the image is interrupted, the time marks cease to advance. Time increments are depicted using white (or green) a nd black marks.

93132802-02 6-15

Page 92

Chapter 6 CVG-200

Using the Menu

6.2.3.9 Image Speed

Sets the speed for sounder imaging. Setting Range：4/1, 3/1, 2/1, 1/1, Stop, 1/2, 1/3, 1/4, 1/6, 1/8, 1/12, 1/16

1/1: For each transmission signal sent out, 1 line is displayed. Stop：Sending of sounder images is stopped. ＊/1: For each transmission signal sent out, ＊ lines are displayed. 1/＊: For ＊ transmissions signal sent out, 1 line is displayed.

When multiple lines are displayed for 1 transmission signal, received signal lines are widened to detect even small schools of fish. This function helps to prevent schools of fish being overlooked. Conversely, when 1 line is displayed for multiple transmissions, small schools of fish are intentionally overlooked.

6.2.3.10 Image Direction

Selects the direction of image movement. Selection: ←｜←｜, ←｜→

←｜←｜：Images begin on the right-hand side and are displayed left ward. ←｜→ ：Images begin in the center and are displayed outward.

In the dual frequency mode, this direction setting is only applicable in normal and vertical partitioned screen settings. In all other cases, imaging flows to the left.

6.2.3.11 Image Partition

Sets the direction of image partitioning. Selection: Vertical, Horizontal

Vertical：The screen is split vertically, creating a left-hand side and a right-hand side. Horizontal：The screen is split horizontally, creating upper and lower screens.

Vertically split

Horizontally split

6.2.3.12 Image Swap

This function allows the swapping of the dual images: left side and right side, or upper and lower.

Selection: A|B, B|A

6-16 93132802-02

Page 93

CVG-200 Chapter 6

Using the Menu

6.2.3.13 Color Bar Scale

Sets whether the rainbow pattern is displayed or not. Selection: ON, OFF

ON：Display OFF：Un-displaying

6.2.3.14 Water Temp Display

Rainbow Pattern

This function sets: (1) if the water temperature shall be displayed or not, and (2) the units of display. Setting Range: OFF, ℃,

OFF：Water temperature, and boat speed are not displayed.

℃: Water temperature and graph units are displayed in ℃. ﾟF: Water temperature and graph units are displayed in ﾟF.

When the water temperature unit is set, the boat speed is also displayed. Set the units of measurement for boat speed using the following procedure:

→“Plotter”→”System Settings”→” Distance/Speed”→[Set]→

Normal screen

°F

ater temp. graph

Vertically split screen

Water Temp./Boat speed

Horizontally split screen

6.2.3.15 Water Temp Graph

This function sets: (1) if the water temperature graph shall be displayed or not. Setting Range: OFF, ℃,

OFF：Water temperature graph are not displayed. ON: Water temperature graph are displayed.

93132802-02 6-17

°F

Page 94

Chapter 6 CVG-200

Using the Menu

6.2.4 Automatic

6.2.4.1 Auto Setting

Sets the functions for auto ranging. Selection: OFF, Range, Shift

OFF: Auto ranging is turned of f. Range: This mode displays everything from

the sea bottom to the surface.

Shift: This key switches in-between engaging

and turning off the auto shift.

When the depth range is set, the device automatically adjusts itself in order to always display the sea bottom. The shift key switches in-between engaging and turning off the auto shift.

Range

6.2.4.2 Auto Gain

Determines whether or not the Auto Gain function is utilized. Setting Range: OFF, ON

OFF: Auto Gain is not utilized. ON: Auto Gain is utilized.

The Auto Gain function adjusts the gain so that the image is easy to see and understand.

6-18 93132802-02

Page 95

CVG-200 Chapter 6

Using the Menu

6.2.5 Depth Range Preset

6.2.5.1 Depth Range1 to 8

Sets the maximum depth range for each of the normal modes. Depth ranges (1-8) can be set to the same value, even for varying modes. Setting Range:

m, J.fm, fm, I.fm:

5, 7.5, 10, 15, 20, 25, 30, 35, 40, 45, 50, 55, 60, 65, 70, 75, 80, 85, 90, 95, 100, 110, 120, 130, 140, 150, 160, 170, 180, 190, 200, 210, 220, 230, 250, 260, 270, 280, 290, 300, 310, 320, 330, 340, 350, 360, 370, 380, 390, 400, 450, 500, 550, 600, 650, 700, 750, 800, 850, 900, 950,1000, 1100, 1200

ft:

15, 20, 30, 40, 50, 60, 80, 100, 120, 140, 160, 180, 200, 220, 240, 260, 280, 300, 320, 340, 360, 380, 400, 440, 480, 520, 560, 600, 640, 680, 720, 780, 800, 840, 880, 920, 960, 1000, 1040, 1080, 1120, 1160, 1200, 1240, 1280, 1320, 1360, 1400, 1440, 1480, 1520, 1560, 1600, 1800, 2000, 2200, 2400, 2600, 2800, 3000, 3200, 3400, 3600, 3800, 4000

Depth units are set by the procedure outlined in section 6.2.6.1, “Depth Units” of this manual.

6.2.6 System Setting

6.2.6.1 Depth Unit

Selects the depth unit of measure. Selection: ｍ, fm, J.fm, I.fm, ft

6.2.6.2 Draft Setting

Sets up the depth of draft line. Setting Range:

0.0 to 25.5(

0.0 to 85.0(

m, fm, J.fm, I.fm) ft)

Depth units are set by the procedure outlined in section 6.2.6.1.

By doing so, the target depth equals the actual depth from the water surface.

93132802-02 6-19

Draft

Transducer

Water surface

Page 96

Chapter 6 CVG-200

Using the Menu

6.2.6.3 Bottom Start

Sets up the starting depth of the seabed detection. Setting Range: 0.0 to 20.0(

0.0 to 65.0(ft)

Depth units are set by the procedure outlined in section 6.2.6.1.

Once set, a seabed echo (received signal) shallower than the set up depth will not be detected. Due to this, confusing the transmission line for the seabed will not happen. Should the Bottom Detection Start setting be deeper than the actual sea bottom depth, the sea bottom shall not be properly detected.

m, fm, J.fm, I.fm)

6.2.6.4 Bottom Detection

Sets the range for sea bottom detection. Selection：Inside range(Inner side of the screen), Outside range(Outside of the screen)

Inside range: Detects sea bottoms within the set range displ ayed. Outside range: Detects sea bottoms at twice the range of the set range displayed.

6.2.6.5 Depth Measurement

Sets sea bottom measurement at Auto, High, or Low frequency settings. Selection：Auto, High frequency, Low frequency

Auto: Usually detects sea bottoms at high frequency. Automatically switches to low

frequency with sea bottom is not detected at high frequencies. High frequency: Detects sea bottoms at high frequency. Low frequency: Detects sea bottoms at low frequency.

6.2.6.6 Sonic Correction

Compensates the deviation of sonic velocity. Setting Range: -7 to +2%

A depth indication may deviate from a true value because of the water temperature difference or salt concentration in the water. Corrects the depth indicator value to a known true value.

6.2.6.7 Water Temperature Correction

Compensates the deviation of a temperature value supplied from the speed/temperature sensor. Setting Range: -10.0 to +10.0 (°C or °F)

Sets water temperature data values when connected to: Water temperature sensor (T-81) or water temperature/speed sensor (one of these: ST-80-, ST-90 -1, ST-100-1).

6-20 93132802-02

Page 97

CVG-200 Chapter 6

Using the Menu

6.2.6.8 Boat Speed Correction

Compensates the deviation of a boat speed value supplied from the speed/temperature sensor. Setting Range: -10.0 to +10.0 (kt or km/h)

Sets the correction for boat speed data when connected to: water temperature/speed sensor(one of these: ST -80-1, ST-90-1, ST-100-1)

6.2.6.9 Water Temperature Data

Sets input for water temperature data. Selection: INT , EXT

INT

: Displays input data for water temperature from: Water temperature sensor(T-81)or

Water temperature /Speed sensor(

EXT

: Displays input data for water temperature from external serial data.

6.2.6.10 EXT Trigger Type

Sets priority settings for external trigger signals from external sounders. Selection: OFF, (Triggered on the leading edge) , (Triggered on the trailing edge)

OFF: No external sounder to be connected.

: Transmission synchronizes a sync trigger on the leading edge from an external

sounder.

: Transmission synchronizes a sync trigger on the trailing edge from an external

sounder.

6.2.7 Bottom Detection Adjust

6.2.7.1 High Frequency, Low Frequency

Sets the detection levels for sea bottom detection. Setting Range: -80 to +40

-80(Level low) to +40(Level high)

ST-80-1/ST-90-1/ST-100-1)

Threshold curve

When the sea bottom is displayed but the depth cannot be detected, please change the settings. When the A-Scope is displayed, the threshold curve shall be displayed on the screen.

Refer to Chapter 7 for detailed instructions on Bottom Detection Threshold Adjustment.

93132802-02 6-21

Normal

A sco

Page 98

Chapter 6 CVG-200

Using the Menu

6.3 Plotter Menu

6.3.1 Mark Block Number

Sets the starting numbers for mark blocks. Setting Range: 00000, 00100, 01000, 02000, 03000, 04000, 05000, 06000, 07000, 08000

Please use mark block numbers to signify the fishing season, fishing methods, waypoints, position of sunken ships, and the position of other dangerous items. Specifying mark block number 00000 allows the user to utilize usual marks as well as event memory.

6.3.2 Display Settings

6.3.2.1 Position Data Display

6.3.2.1.1 L / L

Latitude and longitude are displayed as detected. In this menu, the following settings can be made:

(1) Latitude correction: Detected latitudes can be corrected.

Setting Range: -0.300 to +0.300(minutes)

(2) Longitude correction: Detected longitudes can be corrected.

Setting Range: -0.300 to +0.300(minutes)

6.3.2.1.2 LORAN C

Detected latitude and longitude data is converted to LORAN C LOP and displayed. In this menu, the following settings can be made:

(1) LORAN C Station GRI

Setting Range: Refer to Table 2 LORAN C CHAINS

(2) LORAN C Slave station1 to 5

Setting Range: Refer to Table 2 LORAN C CHAINS

(3) Slave station 1 Correction

Setting Range: -30.0 to +30.0us

(4) Slave station 2 Correction

Setting Range: -30.0 to +30.0us

6-22 93132802-02

Page 99

CVG-200 Chapter 6

Using the Menu

6.3.2.1.3 DECCA

Detected latitude and longitude data is converted to DECCA LOP and displayed. In this menu, the following settings can be made:

(1) Chain

Selection: Refer to Table 3 DECCA CHAINS

(2) Decca Slave Station 1

Selection: Red, Green, Purple

(3) Decca Slave Station 2

Selection: Red, Green, Purple

(4) Slave Station１Correction

Setting Range: -03.00 to +03.00(Lane)

(5) Slave Station 2 Correction

Setting Range: -03.00 to +03.00(Lane)

6.3.2.2 Chart Display

Changes made shall be reflected in this menu upon exiting.

6.3.2.2.1 Ocean Color

Sets the color of the sea on the plotter image.

Selection: 1, 2, 3, 4

6.3.2.2.2 Land Color

Sets the color of land on the plotter image.

Selection: Yellow, Brown, Orange, Dark brown

6.3.2.2.3 Boundlines

Determine if boundary lines are displayed or not.

Selection: ON, OFF

6.3.2.2.4 Grid

Determine if grid lines are displayed or not.

Selection: ON, OFF

6.3.2.2.5 Place Name

Determine if the names of places are displayed or not.

Selection: ON, OFF

93132802-01 6-23

Page 100

Chapter 6 CVG-200

Using the Menu

6.3.2.2.6 Lake & River

Determine if lakes and rivers are displayed or not. Selection: ON, OFF

6.3.2.2.7 Cultural Features

Determine if cultural features should be displayed or not. Selection: ON, OFF

6.3.2.2.8 Landmarks

Determine if landmarks are displayed or not. Selection: ON, OFF

6.3.2.2.9 Ports

Determine if ports are displayed or not. Selection: ON, OFF

6.3.2.2.10 Caution Area

Determine if caution areas are displayed or not. Selection: ON, OFF

6.3.2.2.1 1 Lighthouse

Determine if lighthouses are displayed or not. Selection: ON, OFF

6.3.2.2.12 Buoys

Determine if buoys are displayed or not. Selection: ON, OFF

6.3.2.2.13 Signals

Determine if signals are displayed or not. Selection: ON, OFF

6.3.2.2.14 Track & Routes

Determine if tracks & routes are displayed or not. Selection: ON, OFF

6-24 93132802-01

Koden CVG-200 Operation Manual

Specifications and Main Features

Frequently Asked Questions

User Manual