Kodak A-1671 User Manual

A-1671

Use of KODAK
Brown Toner to
Extend the Life
of Microfilm

Introduction

Methodology

Microscopic Blemishes

Some processed silver gelatin microfilms in
storage from two to twenty years have developed
microscopically small colored spots or blemishes.
The fogged leader at the outside of the roll is most
frequently affected by the blemishes, which are
generally red or yellow in color and are smaller in
size than the image characters (for example, a
typewritten letter reduced 20X) on the microfilm.
The spot size does not increase, but the spots
proliferate on the microfilm and can appear in
image areas. A more detailed description of the
blemishes and of the techniques used in inspecting
microfilm is given in National Bureau of Standards

Handbook 96.

The spots are caused by local oxidation of imaged
silver, resulting in the formation of minute deposits
of yellow- or red-colored colloidal silver.
oxidizing agents entering from outside the roll of
microfilm are aerial oxygen, whose action on the
film is strongly accelerated by moisture, and
atmospheric contaminants, such as hydrogen
peroxide, ozone, sulfur dioxide, hydrogen sulfide,
and nitrogen oxides, all occurring in industrial
atmospheres. Assuming your microfilm was
processed to established quality control standards,
microscopic blemishes (redox) may still occur due
to the oxidation of the metallic silver image,
depending on storage or use conditions.

It is the opinion of image stability experts both
within Eastman Kodak Company and outside of
Kodak that the LE-500 designation for properly
manufactured, processed, and stored silver gelatin
microfilms is conservative and may be expected to
outlive the designated Life Expectancy of 500
years. It is also, however, recognized that our
world is changing. The increasing number of
commercial solvents, auto exhausts, ammonia
fumes, paint fumes, solvents, heating gases, and
deteriorating cardboard and paper are only a few
of the many sources of oxidants and peroxides
affecting silver. These oxidants and peroxides are
believed to be the cause of redox blemishes.
Improper storage conditions also accelerate the
formation of redox blemishes.

Once the deterioration of the microfilm occurs,
it cannot be reversed. Silver film duplication,
molecular sieves, and Kodak Brown Toner can be
used to stabilize the microfilm and extend its useful
life under varying storage and use conditions.

1

2,3

Possible

Molecular Sieves

Molecular sieves, or desiccants, are chemical
compounds that act as absorbers of water,
hydrogen peroxide, and other oxidants. These
sieves are also used to offset the vinegar syndrome
caused by the decomposition of acetate film
support4. The sieves are available in the following
packet formats from a company called Multisorb,
with the following part numbers:

Part # Film Format Content

41 ag 43 16 mm 3.5 grams 400 (1 gal)

41 ag 47 35 mm 7.0 grams 200 (1 gal)

41 ag 51 105 mm 12.5 grams 125 (1 gal)

Rule of thumb: The sieve size is 2% of the weight
of the roll of polyester-based film or 4% of acetate­based film.

It should be noted that the sieves need to be
replaced at some interval, depending on storage
conditions. The use of molecular sieves is cited by
the American National Standards Institute (ANSI) as
another procedure to reduce redox blemishes
caused by high humidity conditions and oxidants in
the air. For more information or to obtain molecular
sieves, call Multisorb at 1-800-445-9890 and ask for
Customer Service.

Kodak Brown Toner Treatment

Brown toning is a chemical treatment that changes
the films processed silver to silver sulfide which is
much more resistant to humidity and oxidants.
Kodak Brown Toner will not degrade the quality of
the microfilmed image. After brown toning, areas of
redox blemishes may be clear or change to a more
neutral color. Although the name brown toner
suggests a browner image after toning, this is not
true for microfilm. In fact, after brown toning, areas
of density may appear blacker or more neutral in
color. Brown toning does not affect the D-min or
clear areas of the film when washed properly.

The first documented evidence of redox blemishing
occurred in the early 1960s. One recommendation
from the resulting investigation promoted the use of
low concentrations of potassium iodide in the fixing
bath (0.2 - 0.5 grams per liter).3 This has been
shown to provide a good degree of protection
against redox blemishes. Kodak Microfilm and
Prostar Fix solutions contain this stability-enhancing
iodide. A second recommendation from this study
was gold or selenium toning of the microfilm.

A-1671 December 2001 2

The Image Permanence Institute (IPI) at the
Rochester Institute of Technology (RIT) in
Rochester, New York, extensively researched redox
blemishes in microfilms.
that selenium toning did not effectively stop the
spread of redox. IPI then looked at a polysulfide
solution and Kodak Brown Toner solution in place of
selenium. IPIs testing showed both solutions
stopped the migration of redox blemishes into the
roll of microfilm. As a result of brown toning, toned
microfilm has a higher resistance to the formation
of redox blemishes. The combined use of brown
toning and molecular sieves significantly enhances
film longevity even under adverse conditions.

Based on Eastman Kodak Company and IPI test
results, Kodak Brown Toner has been shown to
provide additional protection against environmental
conditions that promote redox blemishes. The
treatment is effective with freshly processed and
existing microfilm collections.

Kodak Brown Toner solution can be purchased from
Eastman Kodak Company:

Kodak Catalog Number Packaging

140-0928 1 gallon container

Kodak Brown Toner is highly photoactive with
microfilm chemicals. It is recommended that Kodak
Brown Toner be handled in a separate area from
the handling of microfilm developer and fix.

7

IPIs research showed

Health and Safety

When a manufacturer has determined a product is
or contains a hazardous chemical, they are required
to provide a Material Safety Data Sheet (MSDS).
Kodak provides MSDSs with all photographic
processing chemicals, even those that are not
classified as hazardous chemicals. MSDSs are
available by calling 1-800-242-2424, extension 43.
You will need to supply Kodak catalog numbers of
the chemicals for which you need MSDSs. Material
Safety Data Sheets for the actual working solutions
and caution labels for the processor tanks are also
available by calling the same number.

When working with photochemicals, it is
recommended that MSDSs for all Kodak Products
be obtained and consulted for information
pertaining to potential hazards, safe handling
guidelines, ventilation, and personal protective
equipment. While photochemical solutions and
products may contain hazardous ingredients, if the
information contained on the product label and
within each MSDS is read, understood, and
followed, normal use and handling of these
products should not pose a health risk.

Post-Processing Toning Procedures

For Deep Tank Processors*

The deep tank processor is set to run at 900F.
The transport speed is determined based on a
recommended dwell time of 60 seconds in the
brown toner solution. Depending on tank size,
the transport speed varies between processors.
Mix the Kodak Brown Toner solution at a dilution
of 1:100 (1 part brown toner solution to 100 parts
water). Brown toning in deep tank processors can
be performed either in-line (as part of the normal
microfilm developing process) or off-line (use of
a dedicated processor that brown tones microfilm
after it has been processed in a separate
processor). In an Allen F-20 Processor, for
example, in-line brown toning can be accomplished
by the following tank setup:

Tank Solution

1 Developer
2 Developer
3 Wash
4 Fix
5 Fix
6 Wash
7 Brown toner solution
8 Brown toner solution
9 Wash

Calculate the replenishment rate using the following
table and formula:

Replenishment (mL/ft) by Film Width

16 mm 35 mm 105 mm

0.60 1.20 3.60

Replenishment is equal to:
Processor Transport Speed x Table Value

Sample calculation for a deep tank processor:
Film Width: 16 mm
Table Value: 0.60 mL/ft
Transport Speed: 90 ft/min

Replenishment rate is equal to:

0.60 mL/ft x 90 ft/min = 54 mL/min

Off-line brown toning in this Allen F-20 Processor
can be accomplished by filling any two consecutive
tanks with Kodak Brown Toner at the recommended
dilution rate and at a temperature of 900F. A wash
tank is required immediately after the second tank
of brown toner. Set the transport speed to allow a
60 second dwell time in the brown toner solution
and calculate the replenishment rate based on the
formula described above.

*These are starting point recommendations.

Final conditions will vary.

A-1671 December 2001 3

For Table Top Processors*

Mix the brown toner solution at a dilution of
1:25 (1 part brown toner to 25 parts water).
The temperature of the brown toner solution
should be 100
adjust it to allow for a minimum of 25 seconds
of dwell time in the brown toner solution.

As an example, the tank setup for a Kodak Prostar
Processor is the following:

Tank Solution

1 Brown Toner
2 Brown Toner
3 Brown Toner
4 Brown Toner
5 Wash
6 Wash

For this particular application, a constant machine
speed of 10 feet/min yields a dwell time in the
brown toner solution (all four tanks) of 24-25
seconds.

*These are starting point recommendations.

Final conditions will vary.

0

F. If the machine speed varies,

Conclusion

Kodak Brown Toner, using the procedures
described above, has been shown to meet ANSI
specifications for satisfactorily toned film as
described in ANSI/NAPM IT 9.15-1993.5 All films
toned at the Kodak Disaster Recovery Laboratory
will be done in accordance with these procedures
and standards. ANSI/NAPM IT 9.1-1996 (ANSI/ISO
10602-1995)6 recognizes that microfilms given
stabilizing treatments as described here are
expected to achieve their full Life Expectancy (LE)
of 500 years for polyester-based and 100 years
for acetate-based films. If you have questions
about brown toning, please call your local Kodak
Representative or the Kodak Disaster Recovery
Laboratory at 1-800-EKC-TEST (1-800-352-8378)
or 716-253-3907.

Procedure to Ensure Post-Processing Brown Toning

To ensure that the brown toner solution has
changed the processed silver to silver sulfide,
follow this procedure.

After the post-process brown toner treatment has
been completed, measure the background density
(or D-max) of an image of a plain white document
on the microfilm. Bleach a portion of the microfilm
that contains the filmed white documents with
dichromate bleach, wash thoroughly, and dry the
microfilm. Re-measure the background density (or
D-max) of the white document. If 65% or more of
the density remains, the brown toning is sufficient.
This procedure is outlined in ANSI/NAPM IT9.15-

5

1993.

Dichromate bleach is available by ordering the
following from Solutek (1-617-445-5335):

Part Number Description Quantity

P/N 413-24 Microfilm 4 per case; in

Bleach and 1 gallon bottles
Replenisher

A-1671 December 2001 4

References

1. Inspection of Processed Photographic Record
Films for Aging Blemishes, C.S. McCamy,
National Bureau of Standards Handbook 96,
January 24, 1964.

2. Microscopic SpotsA Progress Report, D.G.
Wiest and R.W. Henn, National Micro-News, 70,
249257, June 1964.

3. Microscopic Spots in Processed Microfilm
Their Nature and Prevention, D.G. Wiest and
R.W. Henn, Photographic Science and
Engineering, 7 (5), 253-261 (1963) and
Micrographic Spots in Processed Microfilm:
The Effect of Iodide, R.W. Henn, D.G. Wiest,
and B.D. Mack, Photographic Science and
Engineering, 9 (3), 167-173 (1965).

4. The Effects and Prevention of the Vinegar
Syndrome. A. Tulsi Ram, David F. Kopperl,
Richard C. Sehlin, Stephanie Masaryk-Morris,
James L. Vincent, and Paige Miller, Journal of
Imaging Science and Technology, Volume 38,
Number 3, May/June 1994, pp. 249-261.

5. American National Standard: Imaging Media
(Photography)The Effectiveness of Chemical
Conversion of Silver Images against Oxidation
Methods for Measuring, ANSI/NAPM IT 9.15-

1993.

6. American National Standard: Imaging
MaterialsProcessed Silver-Gelatin Type
Black-and-White FilmSpecifications for
Stability, ANSI/NAPM IT 9.1-1996 (same as
ANSI/ISO 10602-1995).

7. Polysulfide Treatment for Microfilm, James M.
Reilly, D.W. Nishimura, K.M. Cuprika and
P.Z. Adelstein, Journal of Imaging Technology,
Volume 17, Number 3, June/July 1991,
pp. 99-107.

Note: Refer to the latest revision of each ANSI

or ISO Standard specified.

EASTMAN KODAK COMPANY
Document Imaging
Rochester, New York 14650
1-800-243-8811

A-1671 CAT 116 5521 12/01 ©Eastman Kodak Company, 2001 Printed in U.S.A.

KODAK CANADA INC.
Document Imaging
Toronto, Ontario M6M 1V3
1-800-465-6325

Kodak and Prostar are trademarks
of Eastman Kodak Company.

http://www.kodak.com/go/docimaging