Kocom KIV-101, KC-D30, KC-C61 User Manual
Video Doorphone Wiring Diagram
Component
Precautions for Operation
Installation Precautions
Monitor and camera must be installed away from direct
light and counter light.
Camera must be installed at a place free from rain.
Standard height of monitor must be 1,450mm~1,500mm
from ground, centered around brawn tube.
Camera should be installed on the wall in which cement
is completely dry.
If installed during winter season at temperature below
-5, condensation might be generated inside monitor and
camera due to temperature difference between indoors
and outdoors. To prevent breakdown due to such
condensation, connection should be made in 2 hours or
more after installation.
Do not install monitor and camera in locations subject to
direct heating as harmful gases may subsequently be
emitted in significant amounts.
WARNING
To Reduce the risk of fire orelectric shock Do not expose this appliance to rain ormoisture
CAUTION To prevent electric shock, match wide blade of plug to wide slot, fullt insert.
Stopping up pipe as above minimizes
temperature difference between indoors
and outdoors, and also eliminates moisture
and condensation on door camera window.
Stop up P.V.C. pipe using
adiabatic substances, to
prevent air circulation
Name of each part
Surface-mounting Door Camera Installation
DOOR CAMERA INSTALLATION
After attach the body supporter with 2
screws(4x10mm),
put the Door Camera into the grooves of
body supporter,
and then fix it with a screw(2.6x6mm).
After attach the body supporter with 2
screws(4x10mm), insert the upward
support into the upward groove of body
supporter, and then fix it with a
screw(2.6x6mm).
Looking “Upward” Installation
Looking “Downward” Installation
Straight Ahead Installation
After attach the body supporter with 2
screws(4x10mm), insert the Door Camera
into the downward control groove, and
then fix it
with a screw(2.6x6mm).
Standard Height of Door Camera
Standard height of the door camera is 1,400mm
1,450mm from the bottom of one camera to the floor.
In case that the height of Door camera exceeds the
range of min. 1,250mm1,550mm, it is
impossible to control the screen picture with only the
lens angle, and therefore, be careful of the height of
camera installation.
Downward control
groove
Upward control
groove
Upward control
groove
(unit:mm)
Door camera Installation
Bottom base of
One hall Box
Surface mount
Flush mount
bady support
Upward support
Wall
Screw(4x10mm)
Screw(2.6x6mm)
Camera Front
notice
Don’t install the set on a weak or ceiling surface such as plaster or press board, please install the set
on the hard wall or ceiling like firm timber or concrete.
KIV-101 Monitor
KC-C61 Camera & KC-D30 Metal Pinhole Camera
C-Mic
To communicate
with camera or
guardroom
Communication Button
To communicate with
camera or guardroom
Priority
communication Button
To communicate with
camera first
Camera Button
To see the visitor
Guadroom Button
To communicate with
guardroom
Door Release Button
To open the door
Power Lamp
4 inch screen
To identify
visitor
Brightness Control Knob
To control brightness of
monitor screen
Contrast Control Knob
To control contrast of
monitor screen.
Call Signal
Volume Control
Knob
To control calling
signal volume.
Speaker Volume
Control Knob
To control speaker
volume.
AUTO-REC
C-Mic
To communicate with Monitor
Power Lamp
To check power ON/OFF status
Speaker
When visitor calls, the voice from monitor
comes out of the speaker.
Call Button
By pressing the button, the
related house will be called.
Camera Lens
Clear picture quality realized
by adopting 1/3" CCD
Option
Keep away from humidifier and
stove. High temperature and
humidity can cause breakdown.
When cleaning, never use wet
hands, volatile benzene or paint
thinner.
Keep picture clear by cleaning
camera window frequently with
soft cloths.
As this device consists of
electronic precision
components, and high voltage is
generated internally, do not
attempt to disassemble.
Do not drop monitor or door
camera, and avoid strong impact.
Keep away from devices
generating strong magnetic field
(TV, Speaker, etc.) (Picture can be
disturbed or blurred and breakdown
can result)
KC-C61 KC-D30
Power source
Power consumption
Ambient temperature
Braun tube
Communication system
Call signal sound
Output Impedance
Wiring
Max Wiring Distance
DC12V 1V(power from Monitor)
-10~50
Diagonal 120 Diagonal 90
0.1Lux (LED ON)
F:2.0, f=3.0mm F:3.5, f=3.8mm
95(W)127(H)34(D)mm 95(W)127(H)33(D)mm
Monitor Accessories
Screws for fixing
(4x25mm)
Wall hanger panel
Camera Accessories
Monitor & Camera
Main body supporter
Upword adjusting
Supporter for lens angle
Screw for fixing camera
to panel (2.6x6mm)
Screw for fixing camera
main body supporter
(4x25mm)
Upward adjusting
supporter for adjusting
lens angle upward
Specifications
MONITOR
(KIV-101)
CAMERA
(KC-C61)
Metal Pinhole
Camera
(KC-D30)
Power source
Ambient temperature
Angle of picture
Min. Illumination
Lens
Dimension
Power Built-in AC 120V 60Hz
Max.15W, Stand by : 1W
0~+50
4 inch Flat Tube (B/W)
Hands-free system
Camera:Ding-dong, guardroom: Melody
Picture : 75ohm, Voice : 600ohm
4 Wired in polarity / guardroom Wired in non-polarity
0.65 Single Cable/50m Guardroom:IV 0.9mm
Wiring Diagram
When system is attached to 1 rectangular switch box
Basic Installation method of Monitor
Standard height monitor
Wall hanger panel
for fixing Monitor
Wall hanger panel
for fixing Monitor
ScrewWall
1 Rec tangular
switch box
Standard height of monitor is ranged 1,450 ~ 1,500
from bottom to the center of monitor screen.
For installation, avoid the places where there is any
excessive humidity,magnetic force, dangerous
chemicals, direct ray of sun, and any places near a
heater which can cause break down.
Monitor Installation
(unit:mm)
Screw
Caution for wiring
Wiring between videophone and camera is 4 wire in polarity and use 0.65mm or more single cable
Connecting wiring between monitor and door camera should not be installed near other electrical cable,
norbe horizontal.(In such case, clear picture can not be expected due to interruption by electrical noise)
(Option)
Bottom of
1Rectangular
switch box
Center of monitor
T
H
R
I
E
N
N
B
E
E
N
N
E
Z
1.When visitor presses call button of door camera, the ding-dong sound is made from monitor and
visitor image appears in the screen of the monitor.
2.After checking the visitor through the screen, press communication button then you can
communicate with visitor. (The screen of the monitor is automatically off after 3 minutes.)
3.When the conversation is finished with visitor, press communication or camera button, then
screen is off. And you can press door release button in order to open the door automatically.
4.If you want to check the outside, press camera button then the screen is on and you can check
outside. (But you cannot communicate with camera. If you want to communicate with camera,
press communication button.)
Instruction for the priority communication button (It is only available with the communication
through camera)
The function of priority communication button is to send the voice from the monitor to camera in
priority.
Ex) In case the voice from monitor to camera is not heard well and clearly due to the heavy noise
outside, press this priority communication button, then the visitor can hear the voice from the
monitor well and clearly.
1. In case the monitor is connected to the guardroom, if you press the guardroom button, the signal
is made and if the person in guardroom answers, you can communicate. And after conversation
with guardroom, you can press this button again stop to communication.
2.While you communicate with guardroom, if the chime sound from the camera is made the screen
is on, then you can check the visitor. (The screen is on for 30 seconds and automatically off) At
this time, if you press camera or communication button, the communication with guardroom is
ended and you can communicate with the visitor through the camera.
3.While you communicate with the visitor through camera, if the call from guardroom is made, the
melody sound is ringing. And you can communicate with guardroom by pressing guardroom or
communication button after finishing the communication with visitor.
Note : please certainly press guardroom button after finishing the communication
with guardroom.
www.kocom.co.kr
e-mail:export@kocom.co.kr
www.kocominc.com(us)
e-mail:sales@kocominc.com(us)
PRODUCT
MODEL
DATE PURCHASED
WARRANTY PERIOD
AGENCY ADDRESS
KOCOM Warranties the original purchaser of this product
as follows.
1) This product is produced under strict quality control and inspection procedures.
2) If this product breaks down during proper use as a result of product defect, KOCOM
will repair it within one year from date of purchase free of charge.
3) The following cases will be subject to charge, even during warranty period:
a. Breakdown during transport, or through careless treatment, by consumer.
b. Breakdown cause by unauthorized repair, or system modification.
c. Breakdown caused by natural disaster or power disorder.
Warranty
Warranty Card
KIV-101 03.04
To receive after-Sale service, have the following
ready when you contact our branches
1. Name of the product
2. Model number of the product
3. The area of problem
4. Phone number and address at
which you can be contacted.
Call from visitor
Communication with guardroom
How to operate (Instruction for operating)
This manual is based on the date as shown in the right and specifications
are subject to change without notice for quality improvement.
CAUTION :TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT RENOVE COVER(OR
BACK) NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFED
SERVICE PERSONNEL
The lighting flashwith arrowhead sysmbol, Within an equilateral triangle, is intended to
alert the user to the presence of uninsulated “dangerous vollage‘ with in the product ‘s
enclosure that may be of sufficient magnitube arisk of electric snock to persons.
The exclarnation point with in a equilateral triangle, is intended to alert the user to the
presence of important operating and maintenance(Servicing)instructions in the literature
accompanying the appliance.
Notice: Don’t install the set on a weak or ceiling surface such as plaster or press board, Please install the set
on the hard wall or ceiling like firm timber or concrete.
CAUTION: TO PREVENT ELECTRICAL SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE
SLOT, FULLY INSERT" / ATTENTION: POUR VITER LES CHOCS ELECTRIQUES, INTRODUIRE LA
LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET
POUSSER JUSQU'AU FOND.
1. Read Instructions - All the safety and operating instructions should be read before the product is operated.
2. Retain Instructions - The safety and operating instructions should be retained for future reference.
3. Heed Warnings - All warnings on the product and in the operating instructions should be adhered to.
4. Follow Instructions - All operating and use instructions should be followed.
5. Cleaning - Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners.Use a
damp cloth for cleaning.
6. Attachments - Do not use attachments not recommended by the product manufacturer as they
may cause hazards
7. Water and Moisture - Do not use this product near water°°- for example, near a bath tub, wash bowl,
kitchen sink, or laundry tub; in a wet basement; or near a swimming pool; and the like.
8. Accessories - Do not place this product on an unstable cart, stand, tripod, bracket, or table. The product mayfall, causing
serious injury to a child or adult, and serious damage to the product. Use only with a cart, stand, tripod, bracket, or table
recommended by the manufacturer, or sold with the product. Any mounting of the product should follow the manufacturer's
instructions, and should use a mounting accessory recommended by the manufacturer.
9. A product and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause
the product and cart combination to overturn.
This symbol is to be included in the Important Safeguards of applicable units adjacent to Item 9.
Safeguard
10. Ventilation - Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product
and to protect it from overheating, and these openings must not be blocked or covered. The openings should never be
blocked by placing the product on a bed, sofa, rug, or other similar surface. This product should not be placed in a built-in
installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer's instructions have been
adhered to.
11. Power Sources - This product should be operated only from the type of power source indicated on the marking label. If you
are not sure of the type of power supply to your home, consult your product dealer or local power company. For products
intended to operate from battery power, or other sources, refer to the operating instructions.
12. Grounding or Polarization - This product may be equipped with a polarized alternating-current line plug (a plug having one
blade wider than the other). This plug will fit into the power outlet only one way. This is a safety feature. If you are unable
to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to
replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug.
Alternate Warnings - This product is equipped with a three-wire grounding-type plug, a plug having a third (grounding) pin.
This plug will only fit into a grounding-type power outlet. This is a safety feature. If you are unable to insert the plug into
the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the grounding-type
plug.
13. Power-Cord Protection - Power-supply cords should be routed so that they are not likely to be walked on or pinched by
items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point
where they exit from the product.
14. Protective Attachment Plug - The product is equipped with an attachment plug having overload protection. This is a safety
feature. See Instruction Manual for replacement or resetting of protective device. If replacement of the plug is required, be
sure the service technician has used a replacement plug specified by the manufacturer that has the same overload protection
as the original plug.
15. Outdoor Antenna Grounding - If an outside antenna or cable system is connected to the product, be sure the antenna or
cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of
the National Electrical Code, ANSI/NFPA 70, provides information with regard to proper grounding of the mast and
supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of
antenna-discharge unit, connection to grounding electrodes, and requirements for the grounding electrode.
16. Lightning - For added protection for this product during a lightning storm, or when it is left unattended and unused for long
periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the
product due to lightning and power-line surges.
17. Power Lines - An outside antenna system should not be located in the vicinity of overhead power lines or other electric light
or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme
care should be taken to keep from touching such power lines or circuits as contact with them might be fatal.
18. Overloading - Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result in a risk
of fire or electric shock.
19. Object and Liquid Entry - Never push objects of any kind into this product through openings as they may touch dangerous
voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product.
20. Servicing - Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous
voltage or other hazards. Refer all servicing to qualified service personnel.
21. Damage Requiring Service - Unplug this product from the wall outlet and refer servicing to qualified service personnel
under the following conditions:
A.When the power-supply cord or plug is damaged.
B.If liquid has been spilled, or objects have fallen into the product.
C.If the product has been exposed to rain or water.
D.If the product does not operate normally by following the operating instructions. Adjust only those
controls that are covered by the operating instructions as an improper adjustment of other controls may result in
damage and will often require extensive work by a qualified technician to restore the product to its normal
operation.
E.If the product has been dropped or damaged in any way.
F.When the product exhibits a distinct change in performance - this indicates a need for service.
22. Replacement Parts - When replacement parts are required, be sure the service technician has used replacement
parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions
may result in fire, electric shock, or other hazards.
23. Safety Check - Upon completion of any service or repairs to this product, ask the service technician to perform
safety checks to determine that the product is in proper operating condition.
24. Wall or Ceiling Mounting - The product should be mounted to a wall or ceiling only as recommended by the
manufacturer.
25. Heat - The product should be situated away from heat sources such as radiators, heat registers, stoves, or other
products (including amplifiers) that produce heat.
Class B device
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to pro-vide reasonable protection against harmful interference in a
residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not in-stalled and used in accordance
with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
CAUTION : Changes or modifications not expressly approved by the manufacturer responsible for compliance could
void the user’s authority to operate the equipment.
Thank you very much
for purchasing KOCOM
video doorphone.
please read this manual
thoroughly to ensure
correct usage, before
operating
KIV-101
KC-C61
HANDS-FREE VIDEOPHONE
KIV-101 Operating Installation Manual
Clear & Bright Picture at Low Light
4Flat Monitor
4 Wired
Easy Installation
Slim Size Camera
Wide view angle
KC-C61 (120)
KC-D30 (90)
Hands-free System
Metal Pinhole Camera
KC-D30
Option
Loading...