Contents
1. INTRODUCTION ............................................................................................... 2
2. PACKING LIST .................................................................................................. 2
3. SPECIFICATIONS .............................................................................................. 2
3.1 E
XTERNAL INTERFACE
............................................................................................. 2
3.2 T
ECHNICAL PARAMETERS
........................................................................................ 3
4. FUNCTIONS ...................................................................................................... 3
4.1 P
ROTOCOLS
.......................................................................................................... 3
4.2 GPS .................................................................................................................... 4
4.3 R
EAL-TIME MONITORING
....................................................................................... 4
4.4 V
EHICLE’S LOCATION
............................................................................................. 4
4.5 A
BNORMAL ALERT
.................................................................................................. 4
4.6 M
ILEAGE OF TRIP
.................................................................................................. 4
4.7 F
UEL CONSUMPTION OF TRIP
.................................................................................. 4
4.8 R
EMOTE MAINTENANCE
.......................................................................................... 4
4.9 D
IAGNOSTIC FUNCTIONS
........................................................................................ 4
5. INSTALLATION ................................................................................................. 4
5.1 A
CCOUNT REGISTRATION
....................................................................................... 4
5.2 SIM
CARD INSTALLATION
...................................................................................... 5
5.3 P
ARAMETER SETTINGS
........................................................................................... 5
5.4 D
EVICE INSTALLATION
........................................................................................... 6
5.5 D
IAGNOSTIC LINK CONNECTOR
............................................................................... 6
5.6 U
SING
.................................................................................................................. 7
6. DISCLAIMER ..................................................................................................... 8
7. WARRANTY ....................................................................................................... 8
8. FAQ ................................................................................................................... 9
9. STATEMENT .................................................................................................... 10
1. Introduction
This product is an intelligent electronic terminal for automotive. It bases on OBD II/EOBD standard,
with tracking, alarming, and remote diagnostic function. It combines the world leading technology
of Global Position System (GPS), the technology of General Packet Radio Service (GPRS) and the
technology of intelligent controlling all in one.
The product is consisted with OBD diagnostic module and GSM communication module, and has
optional external G-Mouse (Model: HT-166U). This terminal will deliver vehicles live data and GPS
information to the control center via GPRS. The center will analyze, statistic, store and display to
users.
2. Packing List
Parts name Quantity Note
iDD-212G Device 1 ●
USB Data Cable 1 ●
Product Handbook 1 ●
G-Mouse Receiver (HT-166U) 1
○
OBD Connector Extension Cord 1
○
Note: ● Standard configuration ○ Optional configuration
(If not select any when ordering, the optional devices will not be included when packing)
3. Specifications
3.1 External interface
Product shape shown in the following figure.
1) OBD Connector
It is used to connect with the on-board Diagnostic Link Connector.
The OBD system communicates with external device under the same protocol through this
connector.
2) G-Mouse/Data Interface
This is a multifunction interface. Device connects to PC by USB Data Cable through this connector
when modify the parameters of the device. In normal, this interface can be accessed by G-Mouse
accessories.
3) SIM Card Interface
This is used for inserting the SIM card.
4) Status Indicator
Indicator Color Status
Power LED Red Permanently on - Power on
GSM LED Orange red
Slow blinking (on:0.3s, off:2.7s) - Registered full service
Fast blinking (on:0.5s, off:0.5s) - Network searching/Not
registered
Permanently off - Module off
OBD LED
Green
yellow
Blinking - Device try to communicate with vehicle
Permanently on - Device communicate with vehicle
G-Mouse LED Green
Blinking - GPS signal is good
Permanently on - Searching the GPS signal
3.2 Technical Parameters
Working voltage 9~16V DC Normal current <150 mA@13.8V
Locate mode GPS Sleep current <35mA@12.0V
Location accuracy ≤15m Max current <200mA@13.8V
Locate speed
accuracy
≤0.1m/s Working temp
-30℃～+70℃
Transmission GPRS/SMS Storage temp
-40℃～+85℃
GSM band 850/900/
1800/1900MHz
Relative humidity
5%～95%no frost
Dimension 55*50*28mm
(L*W*H)
Protection class IP30
4. Functions
4.1 Protocols
This product supports all the OBD II standards below:
J1850-PWM
J1850-VPW
ISO 9141-2
ISO 14230-4 (KWP2000)
ISO15765-4(CAN)
4.2 GPS
This product has a GPS satellite signal receiver for enabling global positioning.
4.3 Real-time Monitoring
This product can keep contact with control center through GSM features for enabling real-time
monitoring.
4.4 Vehicle’s Location
User can visit our tracking platform to check vehicle’s position.
4.5 Abnormal Alert
When the following conditions beyond the pre-defined value, the device will send out an extension
alarm to the control center and accompanied with “beep-beep-beep...”.
The conditions including:
High RPM
High Speed
Low Battery Voltage
High Coolant Temperature
Quick Speed-up
Quick Slow-down
Parking long time without ignition off
Towed
Note: For details, please see this handbook – Installation | Parameter Setting.
4.6 Mileage of Trip
At the end of the trip, device will report the driving mileage to the control center.
4.7 Fuel Consumption of Trip
At the end of the trip, device will report the fuel consumption to the control center.
4.8 Remote Maintenance
The parameters of device can be modified through our website
4.9 Diagnostic Functions
Upon user’s request, this product can read/erase diagnostic trouble codes, reset the MIL, and many
live data.
All of the information can be analyzed by the control center, and immediately display to the user
with provision of maintenance recommendations to prevent the extension damages and costs.
5. Installation
5.1 Account Registration
Please contact us to open an account
5.2 SIM Card Installation
Remove the SIM card slot cover and insert the SIM card into the card slot (Note: SIM card gap and
slot miter edge must fit), then replace the device cover (Note: Align the SIM card within the SIM
card slot and gently push).
5.3 Parameter Settings
Please connect the device to PC by using the supplied USB data cable. And then run the OBD
PCTool program after a beep sound. The software GUI is shown below:
Select a correct value for Com Port, and then click the button Open at the top of the window.
Locate the parameters you want by scrolling the scrollbar on the right of the window.
For example the Alarm Parameter, click the button Request to retrieve the current settings in the
device, shown as below:
You can modify the values as you want, and then click the button Apply to store them back into
device.
The same as others, you can find more in the user manual of OBD PCTool.
5.4 Device Installation
Stop and turn off the engine and insert the G-Mouse into the G-Mouse Connector.
Light up and flat on the vehicle. Ensure that there is no block of metal and other items. At the end,
please connect the device to the OBD diagnostic connector firmly.
5.5 Diagnostic Link Connector
Vehicle equipped with OBD system has an DLC on board according to the specification
of J1962. Shown as below:
Pin Description Pin Description
1 Vendor Option 9 Vendor Option
2 SAE J1850 Bus+ 10 SAE J1850 Bus-
3 Vendor Option 11 Vendor Option
4 Chassis Ground 12 Vendor Option
5 Signal Ground 13 Vendor Option
6 ISO 15765-4 (CAN) High 14 ISO 15765-4 (CAN) Low
7 ISO 9141-2 K-Line 15 ISO 9141-2 L-Line
8 Vendor Option 16 Battery Power
In general, the DLC is located within the driver or passenger cabin, from the edge of dashboard on
driver side to the border of 300mm crossed the vehicle centerline on passenger side. It is easy to
touch by sitting in the driver's seat, the preferred location is within the area from steering post to
the vehicle centerline. Shown as below:
5.6 Using
The red led (Power LED) lights on permanently after the device connected to the on-board
Diagnostic Link Connector, accompanied with "beep" one-tone that means power is on.
If the device’s time is not the same as current actual time, the orange red led (GSM LED) blinks fast,
it means the device is searching GSM network, later, if the led blinks slow, and accompanied with
"beep-beep-beep" three-tones that means the device registered to the GSM network, then the
Control Center will synchronize the device’s time. At the same time, the green yellow led (OBD LED)
blinks fast that means the device is communicating with the vehicle’s ECU. Now, start the engine, a
little later, the green yellow led blinks slowly, accompanied with "beep-beep" two-tones that means
the communication has been established.
If the device’s time is the same as current actual time, the green yellow led (OBD LED) blinks fast
that means the device is communicating with the vehicle’s ECU. Now, start the engine, a little later,
the green yellow led blinks slowly, accompanied with "beep-beep" two-tones that means the
communication has been established. Then, the orange red led (GSM LED) blinks fast, it means the
device is searching GSM network, later, if the led blinks slow, and accompanied with
"beep-beep-beep" three-tones that means the device registered to the GSM network.
Turn off the engine, the green yellow led still blinks for about 5 minutes, you’ll hear
"beep-beep-beep" three-tones which means the device disconnected from the network.
After a while, the device will go into sleeping mode and accompanied with "beep" one-tone that
means the device can be plugged out of the on-board Diagnostic Link Connector.
In addition, the G-Mouse LED light on permanently after the G-Mouse module is powered on, and
blinks while positioning.
6. Disclaimer
This handbook is only applies to iDD-212G device.
This product is only applies to the vehicle equipped with OBD II/EOBD.
This product is complied strictly with the series standards of ISO 15031, in principle, it does not
cause any exceptions on vehicles, if you find any exception and worry about it is associated with
this product, please remove it from you vehicle immediately.
G-Mouse communicates with satellite continually. The location function may be affected in
electromagnetic shielding area or bunker place.
The iDD-212G device has a built-in wireless communication module. It should be used as far as
possible away from fuel depots, chemical plants and other areas could cause an explosion. Most
sensitive to external RF sites (such as gas stations, hospitals and school, etc.) may be equipped
with radio frequency jamming equipment, some features of this product may be affected in the
interference area.
Due to the iDD-212G device using GPRS communication technology for transmitting data, you
should use the SIM card which supports GPRS data service and make sure about the account
balances is sufficient. Should not use any SIM card is restricted by region.
To protect the normal use of the product, please use the original accessories.
This handbook is based on the “present” situation. Kocchi's Group Hong Kong LTD
will not guarantee the accuracy, reliability and content of the handbook. Also
Kocchi's reserves the right to amend or withdrawn this handbook without any prior notification.
7. Warranty
If product got quality problem during the warranty period, please bring the product together with a
valid warranty card and purchase invoice to the dealer for checking. Please do not disassemble this
product, we shall not be responsible for those problem caused.
Since purchase, the whole warranty for 1 year and life time maintenance. It will not warranty if it is
improper use or human damage.
User name:
Contact number:
Address:
Post code:
Purchasing date:
Serial number:
Remark:
Please keep this card carefully in order to better serve you.
Distributor (Company Chop):
Maintenance Records
Product Model:
Date
Faults and maintenance of records
Maintenance
(Signature)
User
(Signature)
Fault Description Maintenance
Note: The units in warranty must complete this form carefully.
8. FAQ
Q: External mobile phones cannot receive the alarm information from device.
A: Verify that the SIM card has text message capability, make sure the SIM card is properly inserted
into device before installation, please confirm SIM card account balance sufficient, please confirm
the phone parameter are set correct before installation, please confirm alarm switch is turned on.
(Detail of the parameters setting, see the installation | parameter setting.)
Q: Can the device read diagnostic trouble codes from the Tire Pressure Monitoring System?
A: This product is based on the OBD system, read only the engine system information.
Q: Can the device upload the vehicle’s voltage?
A: This product will report the warning information with the voltage value while the battery voltage
falls below preset limits.
Q: The engine is running, but no trip information, why?
A: If the device time is not synchronized as the same current actual time, it needs to be
synchronized with Control Center via GSM, or with GPS time via G-Mouse, then the trip can begin.
Q: Why does the device sends a “beep” one-tone every 30 seconds?
A: This beep indicates that the vehicle has not equipped with OBD system, this product is not
suitable for the vehicle.
Q: There are trip data, but no tracking data, why?
A: Please make sure you purchase the G-Mouse receiver, make sure that the G-Mouse receiver is
inserted correctly into the device before installing to the vehicle, please confirm G-Mouse receiver
not be obscured, please confirm upload GPS data switch is turned on.
Q: Why it would cause some of the instrument lamps light on?
A: If this is the case, please remove this product immediately and consult our professional
technicians.
9. Statement
Without written permission from Kocchi’s Group HK LTD, it is prohibited reproduce in any form,
transmitted, distributed or save part or all of the contents of this file.
Kocchi’s Group HK LTD implied sustainable development strategy, Kocchi’s reserve the right to
change or improve these products, but may not make any prior notification.
Kocchi’s Group HK LTD reserves the right to change or cancel the content of this file, but may not
make any prior notification.
All right reserved by Kocchi’s Group HK LTD.
Loading...