Kobold PDC Operating Instructions Manual

Operating Instructions

for

Digitalmanometer

Model: PDC

2 PDC K01/0307

GB

1. Foreword 3

2. Digital manometer description 5

3. Commissioning 6

4. Pressure Connection 8

5. Description of Parameters 8

6. Programming

PDC-1 / PDC-2 10

7. Technical data 14

8. CE-conformity 15

9. Maintenance 16

10. Troubleshooting 16

11. Cleaning 16

12. Disposal 16

Content Page 3-16

GB

Manufactured and sold by:

Kobold Messring GmbH

Nordring 22-24

D-65719 Hofheim

Tel.: [phone]

Fax: [phone]

E-Mail: [e-mail]

Internet: www.kobold.com

3PDC K01/0307

GB

1. Foreword

Thank you for the confidence that you have shown in Kobold by purcha­sing the PDC digital manometer.

Like all other Kobold products, PDC digital manometers are a combi­nation of customer requirements, state-of-the-art technology, modern
manufacturing and stringent quality control.

The Kobold digital manometer described in the operating instructions is
designed and produced in line with the most recent developments.
All components are subject to the strictest quality criteria during
production.

These operating instructions have been compiled with care. However,
it is impossible to take every possible usage case into consideration.
For this reason, if you feel that instructions for your particular usage
case are missing, please contact Kobold, and we would be pleased
to provide assistance. Please observe the relevant national safety
regulations during the installation, start-up and operation of this
temperature switch (e.g.: VDE 0100).

Scope
These instructions apply to the PDC series of digital manometers.

Distinctions are drawn between the PDC-1 and PDC-2 models in the
individual sections.
The state of technology at the time of delivery always applies.
Kobold reserve the right to make technical changes without notice.

4 PDC K01/0307

GB

Copyright

All rights to these operating instructions are reserved. These opera­ting instructions, including extracts thereof, must not be copied or
translated into other languages without written permission.

Safety instructions and warnings

Please read these instructions before installing and starting up the
digital manometer.
Failure to follow the instructions will make all guarantee, warranty
and compensation claims null and void.

• Please ensure that the digital manometer is suitable for your
application.

• Please check that the materials that come into contact with the
medium are compatible with the media that are going to be
measured.

• Perfect function and operating reliability of the device can only be
guaranteed for the values specified in the technical data sheet.

• Only qualified persons are permitted to install the equipment and
make the electrical connection, and the correct tools must always
be used.

• Damaged devices must not be started up. If damage occurs
during operation, suitable measures must be taken to
prevent persons or property from being put at risk by the damaged
digital manometer.

• The manometer must only be repaired by

Kobold.
The accepted technical regulations and all national regulations must
always be observed and complied with.

Warning
When screw-fitting the gauges the force required for this must not be

For assembly the following moments may not be exceeded:

applied through the case or terminal box but just through the spanner

flats (with suitable tool) provided for this purpose.

G 1/8 = max. 20Nm - G 1/4 = max. 25Nm - G 1/2 = max. 50Nm

5PDC K01/0307

GB

Exclusion of liability

Kobold guarantees that the digital manometer is in perfect working
condition when it is delivered. The basis consists of the technical data
in the data sheet and these operating instructions.
Liability cannot be accepted for the suitability of the digital mano­meter.
Usage for any other purpose than the ones that are mentioned in
„Correct purpose of use“ is not permitted.

Claims for compensation will only be entertained by Kobold in the
event of intent or gross negligence. Responsibility for damage to
equipment, systems or the surroundings of the digital manometer
will not be accepted.
No liability is accepted for damage caused by incorrect operation.
The haulage contractor is responsible for damage that occurs in
transit.

2. Digital manometer description

The digital manometer is available in two versions PDC-1 and PDC-2
for most varied areas of use.

The digital manometer offers the user numerous measuring units
(bar, psi and MPa). Additional functions such as MIN/MAX memory,
tare adjustment plus bar graph with trailing pointer function round
off the digital manometer’s profile. The programmable parameters
are adjusted by means of user-friendly keys on the front.