Kobe RA2830SQB1 User Manual

Model No.

RA3830SQB-WM-1(30”) / RA3836SQB-WM-1 (36”)

KOBE Brand Range Hood

RA3830SQB-1 (30”) / RA3836SQB-1 (36”)

RA2830SQB-1 (30”) / RA2836SQB-1 (36”)

RA2830SQB-WM-1 (30”) / RA2836SQB-WM-1 (36”)

INSTALLATION INSTRUCTIONS

AND OPERATION MANUAL

IMPORTANT

READ THIS FIRST

NO RETURN, NO REFUND, NO EXCHANGE IF:

1. PRODUCT HAS BEEN INSTALLED

2. KNOCK-OUT HOLES HAVE BEEN PUNCTURED

3. MISSING ORIGINAL PACKAGING MATERIAL AND/OR
PARTS

READ BEFORE INSTALLATION

1. Carefully check all contents of packages;

2. Thoroughly inspect the unit for any cosmetic damages or

defects;

3. Test the unit before installation;

4. Have a certified contractor/electrician do the installation.

IF THERE IS ANY PROBLEM:

1. DO NOT INSTALL THE UNIT AND KEEP ALL ORIGINAL

PACKAGING MATERIAL.

2. Have your original invoice as proof of purchase and

product serial number ready.

3. Call 1-877-BUY-KOBE (289-5623); or e-mail to

[e-mail] to report the problem.

[ENGLISH]

- READ AND SAVE THESE INSTRUCTIONS -

CONTENTS

IMPORTANT SAFETY INSTRUCTIONS .................................................................................... 1

COMPONENTS OF PACKAGE.................................................................................................. 3

INSTALLATION .......................................................................................................................... 7

OPERATING INSTRUCTIONS..................................................................................................13

MAINTENANCE ................................................................ ........................................................15

SPECIFICATIONS ....................................................................................................................16

MEASUREMENTS & DIAGRAMS .............................................................................................18

PARTS LIST ..............................................................................................................................21

CIRCUIT DIAGRAM ..................................................................................................................25

TROUBLE SHOOTING .............................................................................................................26

WARRANTY ............................................................................................................................. 27

PRODUCT REGISTRATION .....................................................................................................29

- READ ALL INSTRUCTIONS CAREFULLY BEFORE STARTING -

AL L W IR IN G MU S T BE D O N E B Y A P R O FE SS IO N A L A ND I N

AC CO RD AN C E W I T H NA TI O NA L A N D L OC AL E L EC T R I CA L CO DE S

IMPORTANT SAFETY INSTRUCTIONS

NOTE

-

This warranty is void without an authorized agent’s receipt or if unit is
damaged due to misuse, poor installation, improper use, mistreatment,
negligence or any other circumstances beyond the control of KOBE
RANGE HOODS authorized agents. Any repair carried out without the
supervision of KOBE RANGE HOODS authorized agents will
automatically void the warranty.

- KOBE RANGE HOODS will not be held responsible for any damages to
personal property or real estate or any bodily injuries whether caused
directly or indirectly by the range hood.

- PLEASE READ THIS SECTION CAREFULLY BEFORE INSTALLATION -

WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR PERSONAL

INJURY, OBSERVE THE FOLLOWING:

1) Installation and electrical wiring must be done by qualified professionals and in accordance with all
applicable codes and standards, including fire-rated construction.

2) When cutting or drilling into wall or ceiling, be careful not to damage electrical wiring or other hidden
utilities.

3) Ducted fans must be vented to the outside.
a) Before servicing or cleaning unit, open the light panel and SWITCH POWER OFF AT SERVICE

PANEL.

b) Clean all grease laden surfaces frequently. To reduce the risk of fire and to disperse air

properly, make sure to vent air outside. DO NOT vent exhaust air into wall spaces, attics, crawl
spaces or garages.

WARNING: TO REDUCE THE RISK OF PERSONAL INJURY IN THE EVENT OF A RANGE

TOP GREASE FIRE:

1. Keep all fan, baffle/spacer/filter/oil tunnel/oil container and grease-laden surfaces clean. Grease
should not be allowed to accumulate on fan, baffle/spacer/filter/oil tunnel/oil container.

2. Always turn hood ON when cooking.

3. Use high settings on cooking range ONLY when necessary.

4. Do not leave cooking range unattended when cooking.

5. Always use cookware and utensils appropriate for the type and amount of food prepared.

6. Use this unit only in the manner intended by the manufacturer.

7. Before servicing, switch power off at service panel and lock service panel (if possible) to prevent
power from switching on accidentally.

8. Clean ventilating fan frequently.

1

What to Do In The Event Of a Range Top Grease Fire

• SMOTHER FLAMES with a tight fitting lid, cookie sheet, or metal tray, and then turn off the burner.
KEEP FLAMMABLE OR COMBUSTIBLE MATERIAL AWAY FROM FLAMES. If the flames do not
go out immediately, EVACUATE THE AREA AND CALL THE FIRE DEPARTMENT or 911.

• NEVER PICK UP A BURNING PAN – You May Get Burned.

• DO NOT USE WATER, including wet dishcloths or towels – a steam blast will result.

• Use an extinguisher ONLY if:

a) You have a Class A, B, C extinguisher and know how to operate it.
b) The fire is small and contained in the area where it started.
c) The fire department has been called.
d) You can fight the fire with your back to an exit.

What to Do If You Smell Gas

- Extinguish any open flame.

- Do not try to turn on the lights or any type of appliance.

- Open all doors and windows to disperse the gas. If you still smell gas, call the Gas Company and

Fire Department right away.

CAUTION

1) For general ventilation use only. Do not use to exhaust hazardous or explosive materials and
vapors.

2) To reduce the risk of fire, use only metal ductwork. Sufficient air is needed for proper combustion
and exhausting of gases through the flue (chimney) to prevent back drafting.

3) Follow the heating equipment manufacturer’s guideline and safety standards such as those
published by the National Fire Protection Association (NFPA), and the American Society for
Heating, Refrigeration and Air Conditioning Engineers (ASHRAE), and code authorities.

4) Activating any switch on may cause ignition or an explosion.

5) Due to the size and weight of this hood, installation by 2 persons is recommended.

ELECTRICAL SHOCK HAZARD – Can result in serious injury or death.
Disconnect appliance from electric power before servicing. If equipped,
the fluorescent light bulb contains small amounts of mercury, which
must be recycled or disposed of according to Local, State, and Federal
Codes.

2

Range Hood Box

{A} KOBE Range Hood
{B} Warranty Registration Card
{C} Instructions Manual (CD)
{D} Baffle Filter x 2 (30” hood)
x 3 (36” hood)
{E} 6” Round Plastic Collar

{A}

{B}

{C}

{D}

* Pre-installed

{E}

* Pre-installed

COMPONENTS OF PACKAGE

(Must keep all material for returns or refunds)

For Under Cabinet Application

RA3830SQB-1 (30”) / RA3836SQB-1 (36”)

 FOR MORE INFORMATION, PLEASE VISIT OUR WEBSITE www.KOBERangeHoods.com OR

CONTACT KOBE RANGE HOODS AT [phone].

3

Range Hood Box

{A} KOBE Range Hood
{B} Warranty Registration Card
{C} Instructions Manual (CD)
{D} Baffle Filter x 2 (30” hood)
x 3 (36” hood)
{E} 6” Round Plastic Collar
{F} Duct cover Mounting Bracket
{G} Adjustable Duct Cover
{H} Screws Package

{A}

{B}

{C}

{D}

* Pre-installed

{E}

* Pre-installed

{F}

{G}

{H}

3/16 “x 3/8” (8PCS)

(Must keep all material for returns or refunds)

For Wall Mounted Application

RA3830SQB-WM-1 (30”) / RA3836SQB-WM-1 (36”)

 FOR MORE INFORMATION, PLEASE VISIT OUR WEBSITE www.KOBERangeHoods.com OR

CONTACT KOBE RANGE HOODS AT [phone].

4

Range Hood Box

{A} KOBE Range Hood
{B} Warranty Registration Card
{C} Instructions Manual (CD)
{D} Baffle Filter x 2 (30” hood)
x 3 (36” hood)
{E} 6” Round Plastic Collar

{A}

{B}

{C}

{D}

* Pre-installed

{E}

* Pre-installed

(Must keep all material for returns or refunds)

For Under Cabinet Application

RA2830SQB-1 (30”) / RA2836SQB-1 (36”)

 FOR MORE INFORMATION, PLEASE VISIT OUR WEBSITE www.KOBERangeHoods.com OR

CONTACT KOBE RANGE HOODS AT [phone].

(Must keep all material for returns or refunds)

5

Range Hood Box

{A} KOBE Range Hood
{B} Warranty Registration Card
{C} Instructions Manual (CD)
{D} Baffle Filter x 2 (30” hood)
x 3 (36” hood)
{E} 6” Round Plastic Collar
{F} Duct cover Mounting Bracket
{G} Adjustable Duct Cover
{H} Screws Package

{A}

{B}

{C}

{D}

* Pre-installed

{E}

* Pre-installed

{F}

{G}

{H}

3/16 “x 3/8” (8PCS)

For Wall Mounted Application

RA2830SQB-WM-1 (30”) / RA2836SQB-WM-1 (36”)

 FOR MORE INFORMATION, PLEASE VISIT OUR WEBSITE www.KOBERangeHoods.com OR

CONTACT KOBE RANGE HOODS AT [phone].

6

TABLE 1

A = Height of Floor to Ceiling
B = Height of Floor to Counter Top

(Standard: 36")

C = Preferred Height of Counter Top

to Hood Bottom (Minimum
26" to 30")

D = Height of Hood
E = Height of the Cabinet

TABLE 2

A = Height of Floor to Ceiling
B = Height of Floor to Counter Top

(Standard: 36")

C = Preferred Height of Counter Top

to Hood Bottom (Minimum
26" to 30")

D = Height of Hood
E = Height of Duct Cover [F – D]
F = Height of the Hood Installation
[A – (B+C)]

INSTALLATION

PLEASE READ ENTIRE INSTRUCTIONS BEFORE PROCEEDING

Calculation before Installation

To calculate installation, please refer to TABLE 1. (All calculation in inches.)

- FOR UNDER THE CABINET -

- FOR WALL MOUNT (WITH OPTIONAL DUCT COVER) -

7

UNDER THE CABINET
WALL MOUNT

9

11

SAFETY WARNING

HOOD MAY HAVE VERY SHARP EDGES; PLEASE WEAR PROTECTIVE GLOVES IF
REMOVING ANY PARTS FOR INSTALLING, CLEANING OR SERVICING.

NOTE: BE CAREFUL WHEN USING ELECTRICAL SCREWDRIVER, DAMAGE TO THE HOOD

MAY OCCUR.

Installation Contents

8

Preparation before Installation

Hood Installation

UNDER CABINET INSTALLATION

For Model No.: RA3830SQB-1 / RA3836SQB-1 / RA2830SQB-1 / RA2836SQB-1

NOTE: TO AVOID DAMAGE TO YOUR HOOD,

PREVENT DEBRIS FROM ENTERING THE
VENT OPENING.

- Decide the location of the venting pipe from the

hood to the outside. (Figure 1)

- A straight, short vent run will allow the hood to

perform more efficiently.

- Try to avoid as many transitions, elbows, and long

run as possible. This may reduce the
performance of the hood.

- Temporarily wire the hood to test for proper

operation before installing. If the hood does not
operate, check the circuit breaker or house
fuse. If the hood is still not working,
disconnect power supply and check the
continuity of all wire connections.

- Peel protective film off the hood (if any).

- Use duct tape to seal joints between pipe sections.

- Make sure the cabinet has full access opening for

the hood as shown on Figure 2.

- Using reference on Page 18-19 to measure and

create access opening for electrical wires and
exhaust under the cabinet.

CAUTION: USE HAND TOOLS ONLY. DO NOT

OVER TIGHTEN SCREWS. IT MAY CAUSE DAMAGE TO
THE HOOD.

CAUTION: If moving the cooking range is

necessary to install the hood, turn off the power in
an electric range at the main electrical box. SHUT
OFF THE GAS BEFORE MOVING A GAS RANGE.
And use a protective covering to protect cooktop
and/or countertop from damage.

1. Using references on Table 1 and measurements
on page 18-19 mark the leveling point for hood­mounting bracket inside the cabinet.

2. Secure two hood mounting screws (not provided)

inside the cabinet leaving 1/8” away from the

cabinet as shown on Figure 3.

3. Loosen hood-mounting brackets at the back of the
hood, adjust brackets and tighten screws as
shown in Figure 4.

4. Refer to Figure 5. Align hood-mounting bracket to
the mounting screws inside the cabinet and hook
hood into place. Secure and tighten the mounting
screws.

CAUTION: MAKE SURE THE HOOD IS

SECURE BEFORE RELEASING.

9

Figure 1

Figure 2

Figure 3

Figure 4

Ductwork Installation

Wiring to Power Supply

Install / Uninstall Accessories

Final Assembly

5. Use steel pipe to connect the 6” round plastic
collar {E} on the hood to the ductwork above. Use
duct tape to make all joints secure and air tight.
Refer to Figure 6

THIS RANGE HOOD MUST BE PROPERLY
GROUNDED. MAKE SURE THIS IS DONE BY
QUALIFIED ELECTRICIAN IN ACCORDANCE WITH
ALL APPLICABLE NATIONAL AND LOCAL
ELECTRICAL CODES. BEFORE CONNECTING
WIRES, SWITCH POWER OFF AT SERVICE PANEL
AND LOCK SERVICE PANEL TO PREVENT POWER
FROM BEING SWITCHED ON ACCIDENTALLY.

- If hood is operating normally, connect three

wires (black, white and green) to house wires
and cap with wire connectors.

- Store wires in the wiring box.

6. Place baffle filters underneath the hood. (Figure 7)

7. Turn power ON in control panel. Check all lights

and fan operation.

8. Leave this Installation Instructions and Operation

Manual for the homeowner.

Figure 5

Figure 6

Figure 7

10

Preparation before Installation

Hood Installation

Mounting Screws

WALL MOUNT INSTALLATION

For Model No.: RA3830SQB-WM-1 / RA3836SQB-WM-1 / RA2830SQB-WM-1 / RA2836SQB-WM-1

NOTE: TO AVOID DAMAGE TO YOUR HOOD,

PREVENT DEBRIS FROM ENTERING
THE VENT OPENING.

- Decide the location of the venting pipe from

the hood to the outside. Refer to Figure 8.

- A straight, short venting run will allow the hood

to perform more efficiently.

- Try to avoid as many transitions, elbows, and

long run as possible. This may reduce the
performance of the hood.

- Temporarily wire the hood to test for proper

operation before installing. If the hood does
not operate, check the circuit breaker or
house fuse. If the hood is still not working,
disconnect power supply and check the
continuity of all wire connections.

- Peel protective film off the hood (if any).

- Use duct tape to seal the joints between pipe

sections.

- If necessary, prepare back wall frame with

cross framing lumber for secure installation.
Using references on Table 2 and
measurements on page 18-20, decide the level
of the lumber. Refer to Figure 9.

CAUTION: USE HAND TOOLS ONLY. DO NOT

OVER TIGHTEN SCREWS. IT MAY CAUSE DAMAGE
TO THE HOOD.

CAUTION: If moving the cooking range is

necessary to install the hood, turn off the power
in an electric range at the main electrical box.
SHUT OFF THE GAS BEFORE MOVING A
GAS RANGE. And use a protective covering to
protect cooktop and/or countertop from
damage.

1. Using references on Table 2 and

measurements on page 18-20, mark the
leveling point of the hood. Position mounting

screws (not provided) on the wall, leaving 1/8”

away from the wall as shown in Figure 10.

2. Loosen hood-mounting brackets at the back of

the hood, adjust brackets and tighten screws
as shown in Figure 11.

3. Align Hood-Mounting Bracket to the two

screws on the wall and hook hood into place.
Tighten screws to secure hood to the wall.

CAUTION: MAKE SURE THE HOOD IS

SECURE BEFORE RELEASING.

Figure 8

Figure 9

Figure 10

Figure 11

11

Wiring to Power Supply

Ductwork Installation

Duct Cover Installation

Install / Uninstall Accessories

Final Assembly

Attach Together

THIS RANGE HOOD MUST BE PROPERLY
GROUNDED. MAKE SURE THIS IS DONE BY
QUALIFIED ELECTRICIAN IN ACCORDANCE
WITH ALL APPLICABLE NATIONAL AND
LOCAL ELECTRICAL CODES. BEFORE
CONNECTING WIRES, SWITCH POWER OFF
AT SERVICE PANEL AND LOCK SERVICE
PANEL TO PREVENT POWER FROM BEING
SWITCHED ON ACCIDENTALLY.

- If hood is operating normally, connect three

wires (black, white and green) to house wires
and cap with wire connectors.

- Store wires in the wiring box.

4. Use steel pipe to connect the exhaust on the

hood to the ductwork. Use duct tape to make

all joints secure and air tight.

5. Mark the position of the Duct Cover-Mounting

Bracket {F}. Use reference E from Table 2 and

measurements on page 18-20. Attach and

secure Duct Cover-Mounting Bracket {F} with

two screws (not provided). Refer to Figure 12.

NOTE: Inner duct cover will cover the Duct

Cover-Mounting Bracket.

6. Remove the Baffle Filters. Position the entire

duct cover up onto the hood and secure with

six (3/16” x 3/8”) screws {H} from inside the

hood towards the outer duct cover.

7. Secure the inner duct cover with two (3/16” x

3/8”) screws {H} to the Duct Cover-Mounting

Bracket {F}. Shown in Figure 13.

8. Place baffle filters underneath the hood.

(Figure 14)

9. Turn power ON in control panel. Check all

lights and fan operation.

10. Leave this Installation Instructions and

Operation Manual for the homeowner.

Figure 12

Figure 13

Figure 14

12

OPERATING INSTRUCTIONS

For RA-038-SQB-1 or RA-038-SQB-WM-1 Series
Model No.: RA3830SQB-1 / RA3836SQB-1

RA3830SQB-WM-1 / RA3836SQB-WM-1

Note: For best results, turn fan on prior to any preparation or cooking and keep fans running while cooking. Adjust
speed as needed.

To operate the fan function

 Press button to choose from speed.

o Q = QuietMode™ speed
o L = Low speed
o H = High speed

 Press “OFF” to turn fan off.

To operate the light function

 Press the Light Control to turn lights on and off.

13

For RA-028-SQB-1 or RA-028-SQB-WM-1 Series
Model No.: RA2830SQB-1 / RA2836SQB-1

RA2830SQB-WM-1 / RA2836SQB-WM-1

Note: For best results, turn fan on prior to any preparation or cooking and keep fans running while cooking. Adjust
speed as needed.

To operate the fan function

 Press On/Off Control to turn on the power.
 Once the On/Off Control is turned on, the prior fan selection will turn on. Press the Speed

Controls (Low, High or QuietMode™) to select the desired speed.

 QuietMode™ supersedes all other fan control. Turn off QuietMode™ to use Low or High

speed.

 Press On/Off Control to turn fan off.

To operate the light function

 Press the Light Control to turn lights on and off.

Note: The Power Control switch is the main power controller.

14

MAINTENANCE

For optimal performance, clean the range hood surface and baffles regularly.

To Clean Hood Surface
CAUTION: NEVER USE ABRASIVE CLEANERS, PADS, OR CLOTHS.

*** Regular care will help preserve its fine appearance.

1. Use only mild soap or detergent solutions. Dry surfaces using soft cloth.

2. If hood looks splotchy (stainless steel hood), use a stainless steel cleaner to clean the surface
of the hood. Avoid getting cleaning solution onto or into the control panel. Follow directions of
the stainless steel cleaner. Caution: Do not leave on too long as this may cause damage to
hood finish. Use soft towel to wipe off the cleaning solution, gently rub off any stubborn spots.
Use dry soft towel to dry the hood.

3. DO NOT allow deposits to accumulate or remain on the hood.

4. DO NOT use ordinary steel wool or steel brushes. Small bits of steel may adhere to the surface
and cause rusting.

5. DO NOT allow salt solutions, disinfectants, bleaches, or cleaning compounds to remain in
contact with stainless steel for extended periods. Many of these compounds contain chemicals,
which may be harmful. Rinse with water after exposure and wipe dry with a clean lint free cloth.

For Baffle Filter models only: to Clean Baffle Filter/Oil Tunnel
CAUTION: DRAIN OIL FROM BAFFLE FILTERS, SPACERS & OIL TUNNEL REGULARLY TO

PREVENT OVERFLOW.

1. Remove all the baffle filters, spacers and oil tunnel.

2. Using a sponge, wash with warm soapy water. Dry completely before returning into place.

CAUTION: SHARP EDGES

(Note: Baffle Filters are top rack dishwasher safe.)

15

MODEL / SIZE

For Under Cabinet Application:
RA3830SQB-1 (30”) ; RA3836SQB-1 (36”)
RA2830SQB-1 (30”) ; RA2836SQB-1 (36”)

For Wall Mount Application:
RA3830SQB-WM-1 (30”) ; RA3836SQB-WM-1 (36”)
RA2830SQB-WM-1 (30”) ; RA2836SQB-WM-1 (36”)

COLOR

18-Gauge Commercial Grade Stainless Steel

CONSUMPTION / AMPERE

180W / 1.5A (30”)
300W / 2.5A (36”)

NUMBER OF BLOWER

1

DESIGN

Seamless / Satin Finish

BLOWER TYPE

Double Horizontal Squirrel Cage

EXHAUST

Top –
6" Round

CONTROLS

For RA-038-SQB-1 and RA-038-SQB-WM-1
3-Speed Mechanical Push Control

For RA-028-SQB-1 and RA-028-SQB-WM-1
3-Speed Rocker Switch

LIGHTS

3-Watt LED light x 2

HOOD DIMENSION
(W x D x H)

RA3830SQB-1 and RA3830SQB-WM-1 (29-3/4” x 20-1/2” x 12-5/8”)
RA3836SQB-1 and RA3836SQB-WM-1 (35-3/4” x 20-1/2” x 12-5/8”)

RA2830SQB-1 and RA2830SQB-WM-1 (29-3/4” x 19-5/8” x 11-5/8”)
RA2836SQB-1 and RA2836SQB-WM-1 (35-3/4” x 19-5/8” x 11-5/8”)

OPTIONAL ACCESSORIES
(W x D x H)

1) 30" Stainless Steel Back Panel
SSP30 (30" x 1/10" x 32")

2) 36" Stainless Steel Back Panel
SSP36 (36" x 1/10" x 32")

WEIGHT (lbs)

Net

Gross

RA3830SQB-1 (30”)

RA3836SQB-1 (36”)

RA2830SQB-1 (30”)

RA2836SQB-1 (36”)

RA3830SQB-WM-1 (30”)

RA3836SQB-WM-1 (36”)

RA2830SQB-WM-1 (30”)

RA2836SQB-WM-1 (36”)

SPECIFICATIONS

16

For 30” Hood
*RA3830SQB-1 / RA3830SQB-WM-1
*RA2830SQB-1 / RA2830SQB-WM-1

SPEED

QuietMode™

Low

High

Air Capacity (cfm)

280

450

680

Sone* (dB)

1.0

2.2

5.0

For 36” Hood
*RA3836SQB-1 / RA3836SQB-WM-1
*RA2836SQB-1 / RA2836SQB-WM-1

SPEED

QuietMode™

Low

High

Air Capacity (cfm)

300

440

750

Sone* (dB)

1.0

2.0

5.6

*One sone is equivalent to the sound of a refrigerator at 40 decibels.
**Specifications subject to change without notice.

17

MODEL NO.:

RA3830SQB-1 (30”) / RA3836SQB-1 (36”)

MODEL NO.:

RA3830SQB-WM-1 (30”) / RA3836SQB-WM-1 (36”)

MEASUREMENTS & DIAGRAMS

***All inch measurements are converted from millimeters. Inch measurements are estimated.
***All measurements in ( ) are millimeters.

-FOR UNDER THE CABINET-

- FOR WALL MOUNT -

18

MODEL NO.:

RA2830SQB-1 (30”) / RA2836SQB-1 (36”)

MODEL NO.:

RA2830SQB-WM-1 (30”) / RA2836SQB-WM-1 (36”)

***All inch measurements are converted from millimeters. Inch measurements are estimated.
***All measurements in ( ) are millimeters.

-FOR UNDER THE CABINET-

- FOR WALL MOUNT -

19

***Hood-Mounting Bracket ***Duct Cover-Mounting Bracke

20

MODEL NO.:

RA3830SQB-1 (30”)
RA3836SQB-1 (36”)

NO.

DESCRIPTION

MODEL /SIZE

PART NO.

1

6” Round Plastic Collar

L1-0505-0002

2

Hood Mounting Bracket x 2

L1-0201-03900

3

Capacitor
RA3830SQB-WM-1

L1-0401-0120-04

RA3836SQB-WM-1

L1-0401-0120-24

4

LED Light Driver

L1-04012-D001

5

Electricial Box

L1-0524-0002

6

LED Light (3W)

L1-0403-0301

7

Control Unit

L1-0405-0301

8

Blower System

RA3830SQB-WM-1

L1-0302-0120-804S

RA3836SQB-WM-1

L1-0302-0120-802S

9

Baffle Filters

L1-0214-0122

PARTS LIST

21

MODEL NO.:

RA3830SQB-WM-1 (30”)
RA3836SQB-WM-1 (36”)

NO.

DESCRIPTION

MODEL /SIZE

PART NO.

1

Duct Cover -Mounting Bracket

RA028DC-1
L1-0203-1630

2

Duct Cover (Inner and Outer)

B102-02830

3

6” Round Plastic Collar

L1-0505-0002

4

Hood Mounting Bracket x 2

L1-0201-03900

5

Capacitor
RA3830SQB-WM-1

L1-0401-0120-04

RA3836SQB-WM-1

L1-0401-0120-24

6

LED Light Driver

L1-04012-D001

7

Electricial Box

L1-0524-0002

8

LED Light (3W)

L1-0403-0301

9

Control Unit

L1-0405-0301

10

Blower System

RA3830SQB-WM-1

L1-0302-0120-804S

RA3836SQB-WM-1

L1-0302-0120-802S

11

Baffle Filters

L1-0214-0122

22

MODEL NO.:

RA2830SQB-1 (30”)
RA2836SQB-1 (36”)

NO.

DESCRIPTION

MODEL /SIZE

PART NO.

1

6” Round Plastic Collar

L1-0505-0002

2

Hood Mounting Bracket x 2

L1-0201-03900

3

Capacitor
RA2830SQB-1

L1-0401-0120-04

RA2836SQB-1

L1-0401-0120-24

4

LED Light Driver

L1-04012-D001

5

Electricial Box

L1-0524-0002

6

LED Light (3W)

L1-0403-0301

7

On/Off Switch

L1-0405-0101

8

Speed Switch

L1-0405-0103

9

Speed Switch (QuietMode™)

L1-0405-0104

10

Light Switch

L1-0405-0102

11

Blower System

RA2830SQB-1

L1-0302-0120-804S

RA2836SQB-1

L1-0302-0120-802S

12

Baffle Filters

L1-0214-0122

23

MODEL NO.:

RA2830SQB-WM-1 (30”)
RA2836SQB-WM-1 (36”)

NO.

DESCRIPTION

MODEL /SIZE

PART NO.

1

Duct Cover -Mounting Bracket

RA028DC-1
L1-0203-1630

2

Duct Cover (Inner and Outer)

B102-02830

3

6” Round Plastic Collar

L1-0505-0002

4

Hood Mounting Bracket x 2

L1-0201-03900

5

Capacitor
RA2830SQB-WM-1

L1-0401-0120-04

RA2836SQB-WM-1

L1-0401-0120-24

6

LED Light Driver

L1-04012-D001

7

Electricial Box

L1-0524-0002

8

LED Light (3W)

L1-0403-0301

9

On/Off Switch

L1-0405-0101

10

Speed Switch

L1-0405-0103

11

Speed Switch (QuietMode™)

L1-0405-0104

12

Light Switch

L1-0405-0102

13

Blower System

RA2830SQB-WM-1

L1-0302-0120-804S

RA2836SQB-WM-1

L1-0302-0120-802S

14

Baffle Filters

L1-0214-0122

24

MODEL NO.:

RA3830SQB-1 (30”) / RA3836SQB-1 (36”)
RA3830SQB-WM-1 (30”) / RA3836SQB-WM -1 (36”)

MODEL NO.:

RA2830SQB-1 (30”) / RA2836SQB-1 (36”)
RA2830SQB-WM-1 (30”) / RA2836SQB-WM -1 (36”)

CIRCUIT DIAGRAM

25

Issue

Possible Cause

Solution

After
Installation,
both motors
and lights are
not working.

The power is not on.

Make sure the circuit breaker and the unit’s
power is ON. Use a voltage meter to check the
power supply.

The wire connection is not secure.

Check and tighten wire connection.

The control panel is defective.

Replace the control panel.

Lights are
working, but
motor(s) is not.
The motor(s) is defective.

Replace the motor.

The capacitor(s) is defective.

Replace capacitor(s).

The control panel is defective.

Replace the control panel.

The range
hood is
vibrating.

The blower system is not secure.

Tighten the turbine impeller/squirrel cage and air
chamber.

The turbine impeller/squirrel cage is
not balanced.

Replace the turbine impeller/squirrel cage.

Hood is not secured in place.

Check the installation of hood, tighten the
mounting bracket.

The motor is
working, but
the lights are
not working.

LED light fixture(s) is defective.

Replace LED light fixture(s)

The light wiring(s) is loose.

Check wire continuity from Control Panel to LED
Driver to LED light fixture(s).

The control panel or LED light driver is
defective.

Replace the control panel or LED light driver.

The range
hood is not
venting out
correctly.

The range hood is installed outside of
the manufacture recommended
clearance.

Adjust the clearance between the range hoods
and cook top to 26” to 30”. For Island range
hood, the clearance between the range hoods
and cook top is 30” to 36”.

There is no make-up air inside the
house.

Open the window to enhance the performance
of the range hood by creating a sufficient make­up air.

Obstacle blocking the pipe work.

Remove all obstacles from the duct work.

The pipe size is smaller than the
suggested pipe size.

Change the ducting according to the
manufacture suggestion.

Cold air is
coming into the
home.

The pipe connection is not properly
sealed.

Check the pipe installation.

The damper is not properly installed or
is missing from the installation.

Check the damper installation.

The damper is not installed.

Installing the damper will help eliminate air
backflow.

TROUBLE SHOOTING

26

WARRANTY

WARRANTY CERTIFICATE

KOBE Range Hoods (referred to herein as “we”or “us”) warrants to the original purchaser

(referred to herein as “you” or “your”) all products manufactured or supplied by us to be free
from defect in workmanship and materials as follows:

TWO-YEAR LIMITED WARRANTY FOR PARTS AND LABOR ON KOBE PREMIUM
SERIES:

For two years from the date of your original invoice from a KOBE authorized dealer, we will, at
our sole discretion, choose to repair or replace the product free of charge that failed due to
manufacturing defects.

It is your sole responsibility to ensure the product is readily accessible for the service
technician to perform repairs. The service technician will not, under any circumstance,

remove, alter or modify any fixture built around and/or connected to the product to gain
access to perform repairs.

During the two-year Limited Warranty period, additional charges may apply which include but
are not limited to:

 Service technician travel charges if the requested service location is 30-miles out of

KOBE’s authorized service area

 Parts shipping expenses
 Un-installation of defective product and Installation of replacement product

Warranty Exclusions:

This warranty does not cover, including but not limited to the following:

a. Improper installation.
b. Any repair, alteration, modification not authorized by KOBE.
c. Duct alteration, modification and connection.
d. Incorrect electric current, voltage or wiring.
e. Normal maintenance and service required for the product.
f. Consumable parts such as light bulbs and carbon filters.
g. Improper usage of the product that it is not intended for, such as commercial use,

outdoor use and multi-family use.

h. Normal wear and tear.
i. Chips, scratches or dents by abuse or misuse of the product.
j. Damages caused by accident, fire, flood and other Acts of God.
k. Expenses incurred for service located outside of the designated service area.
l. Purchases from unauthorized dealers.
m. Removal fees of defective product and Installation fees associated with replacement

product.

If we determine that the warranty exclusions listed above apply or if you fail to provide all
necessary documentation for warranty service, you will be responsible for all expenses
associated with the requested service, including parts, labor, shipping, travelling and any other
expense related to the service request.

27

To qualify for warranty service, you must:

1. Have the ORIGINAL proof of purchase

2. Be the ORIGINAL purchaser of the product

3. Have the model number

4. Have the serial number

5. Have a description of the nature of any defect in the product or part

TO REQUEST WARRANTY SERVICE, PLEASE CONTACT THE KOBE RANGE HOODS
SERVICE CENTER:

KOBE SERVICE CENTER (USA ONLY)
Toll Free: 1-855-800-KOBE (5623)
E-mail: [e-mail]

For service in Canada and to report a problem, please contact:
Phone: [phone]
Email: [e-mail]

28

Fill in the blanks and keep this paper with the original invoice in a
safe place for future service purpose.

1. Date of purchase :

2. Model No. :

3. Serial No. :

For warranty service or spare parts purchase contact:

KOBE Service Center (USA ONLY)
Toll Free: 1-855-800-KOBE (5623)
Email: [e-mail]

For service in Canada and to report a problem, please
contact:

Phone: [phone]
Email: [e-mail]

Your notes:

PRODUCT REGISTRATION

29

This KOBE hood is made for use in the USA and CANADA only. We do not recommend
using this hood overseas as the power supply may not be compatible and may violate
the electrical code of that country. Using a KOBE hood overseas is at your own risk

and will void your warranty.

Cette hotte KOBE est fabriquée pour usage aux États-Unis et au Canada seulement. Il

n’est pas recommandé d’utiliser cette hotte à l’étranger puisque l’alimentation électrique
pourrait ne pas être compatible et enfreindre le code de l’électricité de ce pays. L’usage

de la hotte KOBE à l’étranger est à votre propre risque et la garantie sera annulée.

Esta campana de extracción KOBE ha sido fabricada para ser utilizada únicamente en
EE.UU. y CANADÁ. No recomendamos la utilización de esta campana en el extranjero
debido a que la fuente de energía podría no ser compatible y podría violar el código
eléctrico de dicho país. Utilizar una campana KOBE en el extranjero será a su
propio riesgo y anulará la garantía.

KOBE Range Hoods

11775 Clark Street

Arcadia, CA 91006 USA

www.KOBERangeHoods.com

VER.131111

Information subject to change without notice.

30