How it Works
KOBE
Loading...
CH3830SQB-1

KOBE CH3830SQB-1, CH3830SQBD-1, CH3836SQBD-1, CH3836SQB-1 Installation Instructions And Operation Manual

Download
Page 1
www.goedekers.com
Model No.
KOBE Brand Range Hood
CH3830SQB-1 (30”) / CH3836SQB-1 (36”)
CH3830SQBD-1 (30”) / CH3836SQBD-1 (36”)
INSTALLATION INSTRUCTIONS
AND OPERATION MANUAL
Page 2
IMPORTANT
www.goedekers.com
READ THIS FIRST
READ BEFORE INSTALLATION
1. Carefullycheckallcontentsofpackages;
2. Thoroughlyinspecttheunitforanycosmeticdamagesor
defects;
3. Testtheunitbeforeinstallation;
4. Haveacertifiedcontractor/electriciandotheinstallation.
IF THERE IS ANY PROBLEM:
1. DONOTINSTALLTHEUNITANDKEEPALLORIGINAL
PACKAGINGMATERIAL.
2. Haveyouroriginalinvoiceasproofofpurchaseand
productserialnumberready.
3. Call1‐877‐BUY‐KOBE(289‐5623);ore‐mailto
info@koberangehoods.com
toreporttheproblem.
NO RETURN, NO REFUND, NO EXCHANGE IF:
1. PRODUCTHASBEENINSTALLED
2. KNOCK‐OUTHOLESHAVEBEENPUNCTURED
3. MISSINGORIGINALPACKAGINGMATERIALAND/OR PARTS
Page 3
www.goedekers.com
[ENGLISH]
- READ AND SAVE THESE INSTRUCTIONS -
CONTENTS
IMPORTANT SAFETY INSTRUCTIONS ...................................................................................... 1
COMPONENTS OF PACKAGE .................................................................................................... 3
INSTALLATION ............................................................................................................................. 5
OPERATING INSTRUCTIONS ................................................................................................... 16
MAINTENANCE .......................................................................................................................... 21
SPECIFICA TIONS ...................................................................................................................... 22
MEASUREMENTS & DIAGRAMS .............................................................................................. 24
PARTS LIST ................................................................................................................................ 27
CIRCUIT DIAGRAM .................................................................................................................... 31
TROUBLE SHOOTING ............................................................................................................... 32
WARRANTY ................................................................................................................................ 34
PRODUCT REGISTRATION ....................................................................................................... 36
- READ ALL INSTRUCTIONS CAREFULLY BEFORE STARTING -
ALL WIRING MUST BE DONE BY A PROFESSIONAL AND IN
ACCORDANCE WITH NATIONAL AND LOCAL ELECTRICAL CODES
Page 4
IMPORTANT SAFETY INSTRUCTIONS
www.goedekers.com
- PLEASE READ THIS SECTION CAREFULLY BEFORE INSTALLATION -
WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR PERSONAL
INJURY, OBSERVE THE FOLLOWING:
1) Installation and electrical wiring must be done by qualified professionals and in accordance with all applicable codes and standards, including fire-rated construction.
2) When cutting or drilling into wall or ceiling, be careful not to damage electrical wiring or other hidden utilities.
3) Ducted fans must be ve nted to the outside. a ) Before servicing or cleaning unit, open the light panel and SWITCH POWER OFF AT SERVICE
PANEL.
b) Clean all grease laden surfaces frequently. To reduce the risk of fire and to disperse air
properly, make sure to vent air outside. DO NOT vent exhaust air into wall spaces, attics, crawl spaces or garages.
N O T E - This warranty is void without an authorized agent’s receipt or if unit is
damaged due to misuse, poor installation, improper use, mistreatment, negligence or any other circumstances beyond the control of KOBE RANGE HOODS authorized agents. Any repair carried out without the supervision of KOBE RANGE HOODS authorized agents will automatically void the warranty.
- KOBE RANGE HOODS will not be held responsible for any damages to personal property or real estate or any bodily injuries whether caused directly or indirectly by the range hood.
WARNING: TO REDUCE THE RISK OF PERSONAL INJURY IN THE EVENT OF A RANGE
TOP GREASE FIRE:
1. Keep all fan, baffle/spacer/filter/oil tunnel/oil container and grease-laden surfaces clean. Grease should not be allowed to accumulate on fan, baffle/spacer/filter/oil tunnel/oil container.
2. Always turn hood ON when cooking.
3. Use high settings on cooking range ONLY when necessary.
4. Do not leave cooking range unattended when cooking.
5. Always use cookware and utensils appropriate for the type and amount of food prepared.
6. Use this unit only in the manner intended by the manufacturer.
7. Before servicing, switch power off at service panel and lock service panel (if possible) to prevent power from switching on accidentally.
8. Clean ventilating fan frequently.
1
Page 5
www.goedekers.com
What to Do In The Event Of a Range Top Grease Fire
• SMOTHER FLAMES with a tight fitting lid, cookie sheet, or metal tray, and then turn off the burner. KEEP FLAMMABLE OR COMBUSTIBLE MATERIAL AWAY FROM FLAMES. If the flames do not go out immediately, EVACUATE THE AREA AND CALL THE FIRE DEPARTMENT or 911.
• NEVER PICK UP A BURNING PAN – You May Get Burned.
• DO NOT USE WATER, including wet dishcloths or towels – a steam blast will result.
• Use an extinguisher ONLY if: a) You have a Class A, B, C extinguisher and know how to operate it. b) The fire is small and contained in the area where it started. c) The fire department has been called. d) You can fight the fire with your back to an exit.
What to Do If You Smell Gas
- Extinguish any open flame.
- Do not try to turn on the lights or any type of appliance.
- Open all doors and windows to disperse the gas. If you still smell gas, call the Gas Company and
Fire Department right away.
CAUTION
1) For general ventilation use only. Do not use to exhaust hazardous or explosive materials and vapors.
2) To reduce the risk of fire, use only metal ductwork. Sufficient air is needed for proper combustion and exhausting of gases through the flue (chimney) to prevent back drafting.
3) Follow the heating equipment manufacturer’s guideline and safety standards such as those published by the National Fire Protection Association (NFPA), and the American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE), and code authorities.
4) Activating any switch on may cause ignition or an explosion.
5) Due to the size and weight of this hood, installation by 2 persons is recommended.
ELECTRICAL SHOCK HAZARD – Can result in serious injury or death. Disconnect appliance from electric power before servicing. If equipped, the fluorescent light bulb contains small amounts of mercury, which must be recycled or disposed of according to Local, State, and Federal Codes.
2
Page 6
)
www.goedekers.com
COMPONENTS OF PACKAGE
(Must keep all material for returns or refunds)
For Vented Models only: MODEL NO.: CH3830SQB-1 (30”) / CH3836SQB-1 (36”)
Range Hood Box
{A} KOBE Range Hood {B} Warranty Registration Card {C} Instructions Manual ( {D} 3-1/4” x 10” Exhaust {E} Top Vent Cover {F} 6” Round Plastic Collar {G} Baffle Filters x 2 (30” hood) x 3 (36” hood) {H} Stainless Steel Spacer x 2 (30” hood)
{A}
{B} {C}
{D} {E}
{F}
{G} {H}
* Pre-installed * Pre-installed
FOR MORE INFORMATION, PLEASE VISIT OUR WEBSITE www.KOBERangeHoods.com OR
CONTACT KOBE RANGE HOODS AT (626) 775-8880.
CD)
Duct Cover Box (Sold Separately)
{I} Adjustable Duct Cover {J} Screws Package {K} Hood-Mounting Bracket {L} Duct Cover Support x 2 {M} Duct Cover-Mounting Bracket
{I}
{J} {K}
3/16” x 3/8” (6 PCS)
{L}
4 x 6mm (4 PCS
{M}
2 PCS
3
Page 7
)
www.goedekers.com
(Must keep all material for returns or refunds)
For Ductless Models only: MODEL NO.: CH3830SQBD-1 (30”) / CH3836SQBD-1 (36”)
Range Hood Box Duct Cover Box (Sold Separately)
{A} KOBE Range Hood {B} Warranty Registration Card {C} Instructions Manual {D} Baffle Filters x 2 (30” hood) x 3 (36” hood) {E} Stainless Steel Spacer x 2 (30” hood) {F} Charcoal Filter set x 2
{A}
{B} {C}
{D} {E}
* Pre-installed * Pre-installed {F}
(CD)
{G} Adjustable Duct Cover {H} Screws Package {I} Hood-Mounting Bracket {J} Duct Cover Support x 2 {K} Duct Cover-Mounting Bracket
{G}
{H} {I}
3/16” x 3/8” (6 PCS)
{J}
4 x 6mm (4 PCS
2 PCS
{K}
FOR MORE INFORMATION, PLEASE VISIT OUR WEBSITE www.KOBERangeHoods.com OR
CONTACT KOBE RANGE HOODS AT (626) 775-8880.
4
Page 8
www.goedekers.com
INSTALLATION
PLEASE READ ENTIRE INSTRUCTIONS BEFORE PROCEEDING
Calculation before Installation
To calculate installation, please refer to TABLE 1 and TABLE 2. (All calculation in inches.)
TABLE 1
A = Height of Floor to Ceiling B = Height of Floor to Counter Top
(Standard: 36")
C = Preferred Height of Counter Top
to Hood Bottom (Minimum 26" to 30")
D = Height of Hood E = Height of the Cabinet
- FOR UNDER THE CABINET -
- FOR WALL MOUNT (WITH OPTIONAL DUCT COVER) -
TABLE 2
A = Height of Floor to Ceiling B = Height of Floor to Counter Top
(Standard: 36")
C = Preferred Height of Counter Top
to Hood Bottom (Minimum 26" to 30")
D = Height of Hood E = Height of Duct Cover [F – D] F = Height of the Hood Installation [A – (B+C)]
5
Page 9
www.goedekers.com
SAFETY WARNING
HOOD MAY HAVE VERY SHARP EDGES; PLEASE WEAR PROTECTIVE GLOVES IF REMOVING ANY PARTS FOR INSTALLING, CLEANING OR SERVICING.
NOTE: BE CAREFUL WHEN USING ELECTRICAL SCREWDRIVER, DAMAGE TO THE HOOD
MAY OCCUR.
Installation Contents
For Vented Models only:
MODEL NO.:
CH3830SQB-1 (30”) / CH3836SQB-1 (36”)
UNDER THE CABINET WALL MOUNT
For Ductless Models only:
MODEL NO.:
CH3830SQBD-1 (30”) / CH3836SQBD-1 (36”)
UNDER THE CABINET WALL MOUNT
7
10
14 16
6
Page 10
www.goedekers.com
UNDER CABINET INSTALLATION
For Vented Models only: MODEL NO.: CH3830SQB-1 (30”) / CH3836SQB-1 (36”)
Preparation before Installation
NOTE: TO AVOID DAMAGE TO YOUR HOOD,
PREVENT DEBRIS FROM ENTERING THE VENT OPENING.
- Decide the location of the venting pipe from the
hood to the outside. (Figure 1)
- A straight, short vent run will allow the hood to
perform more efficiently.
- Try to avoid as many transitions, elbows, and long
run as possible. This may reduce the performance of the hood.
- Temporarily wire the hood to test for proper
operation before installing. If the hood does not operate, check the circuit breaker or house fuse. If the hood is still not working, disconnect power supply and check the continuity of all wire connections.
- Peel protective film off the hood (if any).
- Use duct tape to seal joints between pipe sections.
- For installing under the cabinet with recessed
bottom, attach 4-inch wide wood filler strips (not included) on each side. (Figure 2)
- Using reference on Page 24 to measure and
create access opening for electrical wires and exhaust under the cabinet.
Vent option installation
CAUTION: USE HAND TOOLS ONLY. DO NOT
OVER TIGHTEN SCREWS. IT MAY CAUSE DAMAGE TO THE HOOD.
1. Choose the require vent option. Some installation screws are already pre-attached to hood.
2. For 6” Round vent installation only:
- The 6” exhaust is already attached. (Figure 3)
Align and secure the 6” Round Plastic Collar {F} to two screws on hood.
3. For Top 3-1/4” x 10” vent installation only:
- Remove attached 6” exhaust and discard.
(Figure 3) Keep 13 screws to install 3-14” x 10” exhaust & vent cover.
- Align and secure Top Vent Cover {E} and 3-1/4”
x 10” Exhaust {D} using 14 screws (13 screws taken from 6” exhaust. (Figure 4)
Figure 1
Figure 2
Figure 3
Figure 4
7
Page 11
www.goedekers.com
4. For Rear 3-1/4” x 10” vent installation only:
- Remove attached 6” exhaust and discard.
(Figure 3) Keep 13 screws to install vent covers.
- Remove duct knockout from back of the hood
and discard. (Figure 5) Unscrew 3-1/4” x 10” Vent Cover from rear exhaust (located inside hood); keep screws to install 3-1/4” x 10” exhaust.
- Align and secure Top Vent Cover {E} and 3-1/4”
x 10” Vent Cover (removed from rear exhaust) using 14 screws (13 screws taken from 6” exhaust. (Figure 5)
- Attach the 3-1/4” x 10” Exhaust {D} to rear
exhaust (located inside hood) using 10 screws taken from rear vent cover. (Figure 6)
Hood Installation
CAUTION: If moving the cooking range is
necessary to install the hood, turn off the power in an electric range at the main electrical box. SHUT OFF THE GAS BEFORE MOVING A GAS RANGE. And use a protective covering to protect cooktop and/or countertop from damage.
5. Remove the bottom casing or baffle filters/stainless steel spacers if necessary; arrange the electrical wires to run through the 1” diameter hole on the top or the rear of the hood.
6. Using references on Table 1 and measurements on page 24, center the hood in place beneath the cabinet and flush with the front of the cabinet.
7. Draw electrical wires through cabinet access opening.
8. Use electrical drill to remove the knockout holes on top of the range hood.
9. Place screw (not provided) into the exact center of each knockout hole. Make sure all screws are in place before tightening screws.
CAUTION: MAKE SURE THE HOOD IS
SECURE BEFORE RELEASING.
Figure 5
Figure 6
8
Page 12
www.goedekers.com
Wiring to Power Supply
CAUTION: If moving the cooking range is
necessary to install the hood, turn off the power in an electric range at the main electrical box. SHUT OFF THE GAS BEFORE MOVING A GAS RANGE. RISK OF ELECTRICAL SHOCK.
THIS RANGE HOOD MUST BE PROPERLY GROUNDED. MAKE SURE THIS IS DONE BY QUALIFIED ELECTRICIAN IN ACCORDANCE WITH ALL APPLICABLE NATIONAL AND LOCAL ELECTRICAL CODES. BEFORE CONNECTING WIRES, SWITCH POWER OFF AT SERVICE PANEL AND LOCK SERVICE PAN EL TO PREVENT POWER FROM BEING SWITCHED ON ACCIDENTALLY.
Figure 7
- If hood is operating normally, connect three
wires (black, white and green) to house wires and cap with wire connectors.
- Store wires in the wiring box.
Ductwork Installation
10. Use steel pipe to connect the exhaust on the hood
to the ductwork. Use duct tape to make all joints secure and air tight.
Install Accessories
11. Place baffle filters & spacers underneath the hood.
(Figure 7)
Final Installation
12. Turn power ON in control panel. Check all lights
and fan operation.
13. Make sure to leave this manual for the
homeowner.
9
Page 13
www.goedekers.com
WALL MOUNT INSTALLATION
***This installation requires purchase of duct cover Model No. CH1120DC-1.
For Vented Models only: MODEL NO.: CH3830SQB-1 (30”) / CH3836SQB-1 (36”)
Preparation before Installation
NOTE: TO AVOID DAMAGE TO YOUR HOOD,
PREVENT DEBRIS FROM ENTERING THE VENT OPENING.
- Decide the location of the venting pipe from
the hood to the outside. Refer to Figure 8.
- A straight, short venting run will allow the hood
to perform more efficiently.
- Try to avoid as many transitions, elbows, and
long run as possible. This may reduce the performance of the hood.
- Temporarily wire the hood to test for proper
operation before installing. If the hood does not operate, check the circuit breaker or house fuse. If the hood is still not working, disconnect power supply and check the continuity of all wire connections.
- Peel protective film off the hood (if any).
- Use duct tape to seal the joints between pipe
sections.
- If necessary, prepare back wall frame with
cross framing lumber for secure installation. Using references on Table 2 and measurements on page 24-26, decide the level of the lumber. Refer to Figure 9.
Vent option installation
CAUTION: USE HAND TOOLS ONLY. DO
NOT OVER TIGHTEN SCREWS. IT MAY CAUSE DAMAGE TO THE HOOD.
1. Choose the require vent option. Some
installation screws are already pre-attached to hood. Refer to Figure 16. Please use Screws Package {J} with pre-attached screws for wall mount installation.
2. For 6” Round vent installation only:
- The 6” exhaust is already attached. (Figure
10) Align and secure the 6” Round Plastic Collar {F} to two screws on hood. Follow instructions in Step 5 to attach Hood Mounting Bracket {K} and two Duct Cover Support {L} (Figure 14)
3. For Top 3-1/4” x 10” vent installation only:
- Remove attached 6” exhaust and discard.
(Figure 10) Keep 13 screws to install 3-14” x 10” exhaust & vent cover.
Figure 8
Figure 9
Figure 10
Figure 11
10
Page 14
www.goedekers.com
- Align Top Vent Cover {E} and 3-1/4” x 10”
Exhaust {D}. (Figure 11) Skip to Step 5 to attach Hood Mounting Bracket {K} and two Duct Cover Support {L} using 14 screws (13 screws taken from 6” exhaust. (Figure 14)
4. For Rear 3-1/4” x 10” vent installation only:
- Remove attached 6” exhaust and discard.
(Figure 10) Keep 13 screws to install vent covers.
- Remove duct knockout from back of the
hood and discard. (Figure 12) Unscrew 3­1/4” x 10” Vent Cover from rear exhaust (located inside hood); keep screws to install 3-1/4” x 10” Exhaust.
- Align Top Vent Cover {E} and 3-1/4” x 10”
Vent Cover (removed from rear exhaust) using 14 screws (13 screws taken from 6” exhaust). (Figure 12) Follow instructions in Step 5 to attach Hood Mounting Bracket {K} and two Duct Cover Support {L} using 14 screws (13 screws taken from 6” exhaust). (Figure 14)
- Attach the 3-1/4” x 10” Exhaust {D} to rear
exhaust (located inside hood) using 10 screws taken from rear vent cover. (Figure
13)
Hood Installation
CAUTION: If moving the cooking range is
necessary to install the hood, turn off the power in an electric range at the main electrical box. SHUT OFF THE GAS BEFORE MOVING A GAS RANGE. And use a protective covering to protect cooktop and/or countertop from damage.
5. Secure Hood-Mounting Bracket {K} and two
Duct Cover Support {L} on top of the hood with eight pre-attached screws. Use four 3/16” x 3/8” screws {J} for Hood-Mounting Bracket {K}. (Figure 14)
6. Using references on Table 2 and
measurements on page 24-26, mark the leveling point of the hood. Position two mounting screws (not provided) on the wall, leaving 1/8” away from the wall as shown in Figure 15.
7. Align Hood-Mounting Bracket {K} to the two
screws on the wall and hook hood into place. Tighten screws to secure hood to the wall.
CAUTION: MAKE SURE HOOD IS
SECURE BEFORE RELEASING
Figure 12
Figure 13
Figure 14
Figure 15
Mounting Screws
11
Page 15
www.goedekers.com
Wiring to Power Supply
CAUTION: If moving the cooking range is
necessary to install the hood, turn off the power in an electric range at the main electrical box. SHUT OFF THE GAS BEFORE MOVING A GAS RANGE. RISK OF ELECTRICAL SHOCK.
THIS RANGE HOOD MUST BE PROPERLY GROUNDED. MAKE SURE THIS IS DONE BY QUALIFIED ELECTRICIAN IN ACCORDANCE WITH ALL APPLICABLE NATIONAL AND LOCAL ELECTRICAL CODES. BEFORE CONNECTING WIRES, SWITCH POWER OFF AT SERVICE PANEL AND LOCK SERVICE PANEL TO PREVENT POWER FROM BEING SWITCHED ON ACCIDENTALLY.
8. If hood is operating normally, connect three
wires (black, white and green) to house wires
and cap with wire connectors.
9. Store wires in the wiring box.
Ductwork Installation
10. Use steel pipe to connect the exhaust on the
hood to the ductwork. Use duct tape to make
all joints secure and air tight.
Duct Cover Installation
11. Mark the position of the Duct Cover-Mounting
Bracket {M}. Use reference E from Table 2
and measurements on page 24-26. Attach
and secure Duct Cover-Mounting Bracket {M}
with two screws (not provided). (Figure 16)
NOTE: Inner duct cover will cover the duct
cover-mounting bracket.
12. Position the entire duct cover up onto the
hood.
13. Secure the inner duct cover with two (3/16” x
3/8”) screws {J} to the duct cover-mounting
bracket. Shown in Figure 17.
14. Fasten outer duct cover to Duct Cover Support
{L} with four (4 x 6 mm) screws {J}.
Figure 16
Figure 17
Attach Together
12
Page 16
www.goedekers.com
Install Accessories (For Baffle Filter models)
15. Place baffle filters & spacers underneath the
hood. (Figure 18)
Final Installation
16. Turn power ON in control panel. Check all
lights and fan operation.
17. Make sure to leave this manual for the
homeowner.
Figure 18
13
Page 17
www.goedekers.com
UNDER CABINET INSTALLATION
For Ductless Models only: MODEL NO.: CH3830SQBD-1 (30”) / CH3836SQBD-1 (36”)
Preparation before Installation
- Temporarily wire the hood to test for proper
operation before installing. If the hood
does not operate, check the circuit
breaker or house fuse. If the hood is
still not working, disconnect power
supply and check the continuity of all
wire connections.
- Peel protective film off the hood (if any).
- For installing under the cabinet with
recessed bottom, attach 4-inch wide wood
filler strips (not included) on each side.
(Figure 19)
- Using reference on Page 25 to measure
and create access opening for electrical
wires and exhaust under the cabinet.
Hood Installation
CAUTION: If moving the cooking
range is necessary to install the hood, turn off the power in an electric range at the main electrical box. SHUT OFF THE GAS BEFORE MOVING A GAS RANGE. And use a protective covering to protect cooktop and/or countertop from damage.
1. Remove the bottom casing or baffle
filters/stainless steel spacers if necessary;
arrange the electrical wires to run through
the 1” diameter hole on the top or the rear
of the hood.
2. Using references on Table 1 and
measurements on page 25, center the
hood in place beneath the cabinet and
flush with the front of the cabinet.
3. Draw electrical wires through cabinet
access opening.
4. Use electrical drill to remove the knockout
holes on top of the range hood.
5. Place screw (not provided) into the exact
center of each knockout hole. Make sure
all screws are in place before tightening
screws.
CAUTION: MAKE SURE THE HOOD IS
SECURE BEFORE RELEASING.
Figure 19
14
Page 18
www.goedekers.com
Wiring to Power Supply
CAUTION: If moving the cooking range
is necessary to install the hood, turn off the power in an electric range at the main electrical box. SHUT OFF THE GAS BEFORE MOVING A GAS RANGE. RISK OF ELECTRICAL SHOCK.
THIS RANGE HOOD MUST BE PROPERLY GROUNDED. MAKE SURE THIS IS DONE BY QUALIFIED ELECTRICIAN IN ACCORDANCE WITH ALL APPLICABLE NATIONAL AND LOCAL ELECTRICAL CODES. BEFORE CONNECTING WIRES, SWITCH POWER OFF AT SERVICE PANEL AND LOCK SERVICE PANEL TO PREVENT POWER FROM BEING SWITCHED ON ACCIDENTALLY .
- If hood is operating normally, connect
three wires (black, white and green) to
house wires and cap with wire
connectors.
- Store wires in the wiring box.
Install Accessories
6. Place baffle filters & spacers underneath the
hood. (Figure 20)
Final Installation
7. Turn power ON in control panel. Check all
lights and fan operation.
8. Make sure to leave this manual for the
homeowner.
Figure 20
15
Page 19
www.goedekers.com
WALL MOUNT INSTALLATION
***This installation requires purchase of duct cover Model No. CH1120DC-1.
For Ductless Models only: MODEL NO.: CH3830SQBD-1 (30”) / CH3836SQBD-1 (36”)
Preparation before Installation
- Temporarily wire the hood to test for proper
operation before installing. If the hood does not operate, check the circuit breaker or house fuse. If the hood is still not working, disconnect power supply and check the continuity of all wire connections.
- Peel protective film off the hood (if any).
- If necessary, prepare back wall frame with
cross framing lumber for secure installation. Using references on Table 2 and measurements on page 25-26, decide the level of the lumber. Refer to Figure 21.
Hood Installation
CAUTION: If moving the cooking range is
necessary to install the hood, turn off the power in an electric range at the main electrical box. SHUT OFF THE GAS BEFORE MOVING A GAS RANGE. And use a protective covering to protect cooktop and/or countertop from damage.
1. Secure Hood-Mounting Bracket {K} and two
Duct Cover Support {L} on top of the hood with eight pre-attached screws. Use four 3/16” x 3/8” screws {J} for Hood-Mounting Bracket {K}. (Figure 22)
2. Using references on Table 2 and
measurements on page 25-26, mark the leveling point of the hood. Position two mounting screws (not provided) on the wall, leaving 1/8” away from the wall as shown in Figure 23.
3. Align Hood-Mounting Bracket {K} to the two
screws on the wall and hook hood into place. Tighten screws to secure hood to the wall.
CAUTION: MAKE SURE HOOD IS
SECURE BEFORE RELEASING
Figure 21
Figure 22
Figure 23
Mounting Screws
16
Page 20
www.goedekers.com
Wiring to Power Supply
CAUTION: If moving the cooking range is
necessary to install the hood, turn off the power in an electric range at the main electrical box. SHUT OFF THE GAS BEFORE MOVING A GAS RANGE. RISK OF ELECTRICAL SHOCK.
THIS RANGE HOOD MUST BE PROPERLY GROUNDED. MAKE SURE THIS IS DONE BY QUALIFIED ELECTRICIAN IN ACCORDANCE WITH ALL APPLICABLE NATIONAL AND LOCAL ELECTRICAL CODES. BEFORE CONNECTING WIRES, SWITCH POWER OFF AT SERVICE PANEL AND LOCK SERVICE PANEL TO PREVENT POWER FROM BEING SWITCHED ON ACCIDENTALLY.
4. If hood is operating normally, connect three
wires (black, white and green) to house wires
and cap with wire connectors.
5. Store wires in the wiring box.
Duct Cover Installation
6. Mark the position of the Duct Cover-Mounting
Bracket {M}. Use reference E from Table 2
and measurements on page 25-26. Attach
and secure Duct Cover-Mounting Bracket {M}
with two screws (not provided). (Figure 24)
NOTE: Inner duct cover will cover the duct
cover-mounting bracket.
7. Position the entire duct cover up onto the
hood.
8. Secure the inner duct cover with two (3/16” x
3/8”) screws {J} to the duct cover-mounting
bracket. Shown in Figure 25.
9. Fasten outer duct cover to Duct Cover Support
{L} with four (4 x 6 mm) screws {J}.
Install Accessories (For Baffle Filter models)
10. Place baffle filters & spacers underneath the
hood. (Figure 18)
Final Installation
11. Turn power ON in control panel. Check all
lights and fan operation.
Make sure to leave this manual for the
homeowner.
17
Figure 24
Figure 25
Figure 26
Attach Together
Page 21
www.goedekers.com
OPERATING INSTRUCTIONS
For Vented Models only: MODEL NO.: CH3830SQB-1 (30”) / CH3836SQB-1 (36”)
Note: For best results, turn fan on prior to any preparation or cooking and keep fans running while cooking. Adjust speed as needed.
To operate the fan function
• Press button to choose from speed.
o Q = QuietMode™ speed o L = Low speed o H = High speed
• Press
“OFF” to turn fan off.
To operate the light function
• Press the Light Control to turn lights on and off.
18
Page 22
www.goedekers.com
For Ductless Models only: MODEL NO.: CH3830SQBD-1 (30”) / CH3836SQBD-1 (36”)
Note: For best results, turn fan on prior to any preparation or cooking and keep fans running while cooking. Adjust speed as needed.
Power Control
Press Power Control to turn On/Off the range hood.
Speed Control
The fan will start on Speed #3. Press increase the speed level.
To activate 3-minute delay shutoff, press and hold activated the LED Display will flash and fan speed will change to Speed #3. Speed level can be adjusted
by pressing To turn fan off immediately, press
Light Control
ECO Mode Control
Press Bright, Medium Bright, Dim, and OFF.
Lights are controlled independently from Power Control and delay shutoff. Turning the power off will not turn lights off.
ECO Mode is set to turn fan on QuietMode™ setting for 10 minutes every hour to remove excess moisture, microscopic particles and odors for better kitchen air quality.
ECO Mode is independent from the Power Control and delay shutoff.
button to decrease the speed level. Press button to
button. Once the delay shutoff has been
or button during the 3-minute countdown.
button a second time.
button to turn LED lights ON. Each press of button will cycle the light intensity through
ECO Mode can be activated while fan is running or off. Press and hold appears in the LED Display. While fan is running you can change the speed, use delay shutoff or turn off
fan without disabling ECO Mode. When fan is off and ECO Mode has been activated, the
button until icon briefly
icon will
19
Page 23
www.goedekers.com
appear in the LED Display. The icon will flash while ECO Mode is operating on QuietMode™. To deactivate, press and hold NOTE: Pressing
speed will be displayed in LED Display. Note: Must open door or windows to create sufficient make-up air when ECO Mode has been activated.
button while ECO Mode is active will activate the regular fan function and the
control button until icon no longer appears in the LED Display.
20
Page 24
www.goedekers.com
MAINTENANCE
For optimal performance, clean the range hood surface and baffles regularly.
To Clean Hood Surface CAUTION: NEVER USE ABRASIVE CLEANERS, PADS, OR CLOTHS.
*** Regular care will help preserve its fine appearance.
1. Use only mild soap or detergent solutions. Dry surfaces using soft cloth.
2. If hood looks splotchy (stainless steel hood), use a stainless steel cleaner to clean the surface of the hood. Avoid getting cleaning solution onto or into the control panel. Follow directions of the stainless steel cleaner. Caution: Do not leave on too long as this may cause damage to hood finish. Use soft towel to wipe off the cleaning solution, gently rub off any stubborn spots. Use dry soft towel to dry the hood.
3. DO NOT allow deposits to accumulate or remain on the hood.
4. DO NOT use ordinary steel wool or steel brushes. Small bits of steel may adhere to the surface and cause rusting.
5. DO NOT allow salt solutions, disinfectants, bleaches, or cleaning compounds to remain in contact with stainless steel for extended periods. Many of these compounds contain chemicals, which may be harmful. Rinse with water after exposure and wipe dry with a clean lint free cloth.
For Baffle Filter models only: to Clean Baffle Filter/Spacers CAUTION: DRAIN OIL FROM BAFFLE FILTERS, SPACERS & OIL TUNNEL (IF ANY)
REGULARLY TO PREVENT OVERFLOW.
1. Remove all the baffle filters, spacers and oil tunnel (if any).
2. Using a sponge, wash with warm soapy water. Dry completely before returning into place.
CAUTION: SHARP EDGES
(Note: Baffle Filters are top rack dishwasher safe.)
21
Page 25
www.goedekers.com
SPECIFICATIONS
For Vented Models only: MODEL NO.: CH3830SQB-1 (30”) / CH3836SQB-1 (36”)
MODEL / SIZE
CH3830SQB-1 (30”) ; CH3836SQB-1 (36”)
COLOR CONSUMPTION / AMPERE
NUMBER OF BLOWER DESIGN
BLOWER TYPE
EXHAUST
CONTROLS LIGHTS HOOD DIMENSION
(W x D x H)
OPTIONAL ACCESSORIES (W x D x H)
WEIGHT (lbs)
18-Gauge Commercial Grade Stainless Steel 232W / 2.21A
2 Seamless / Satin Finish
Twin Vertical Turbine Impeller Top –
6" Round 3-1/4" x 10" Rectangular Rear – 3-1/4" x 10" Rectangular
3-Speed Mechanical Push Control 3-watt LED light x 2 (CH3830SQB-1) 29-3/4" x 21-11/16" x 5-7/8"
(CH3836SQB-1) 35-3/4" x 21-11/16" x 5-7/8"
1) Two-Piece Adjustable Duct Cover (CH1120DC-1) 11-13/16" x 10-7/16" x (22” ~ 41")
2) 30" Stainless Steel Back Panel (SSP30) 30" x 1/10" x 32"
3) 36" Stainless Steel Back Panel (SSP36) 36" x 1/10" x 32"
Net CH3830SQB-1 (30”) 40 44 CH3836SQB-1 (36”) 42 49
Gross
SPEED Air Capacity (cfm) Sone* (dB)
*One sone is equivalent to the sound of a refrigerator at 40 decibels. **Specifications subject to change without notice.
QuietMode™ Low High
300 510 680
1.0 3.0 5.0
22
Page 26
www.goedekers.com
For Ductless Models only: MODEL NO.: CH3830SQBD-1 (30”) / CH3836SQBD-1 (36”)
MODEL / SIZE COLOR
CH3830SQBD-1 (30”) ; CH3836SQBD-1 (36”) 18-Gauge Commercial Grade Stainless Steel
CONSUMPTION / AMPERE NUMBER OF BLOWER
DESIGN
BLOWER TYPE
EXHAUST CONTROLS
ECO MODE (For Ductless Models)
LIGHTS
HOOD DIMENSION (W x D x H)
OPTIONAL ACCESSORIES (W x D x H)
WEIGHT (lbs)
SPEED Air Capacity (cfm) Sone* (dB)
232W / 2.21A 2
Seamless / Satin Finish
Twin Vertical Turbine Impeller Ductless
Electronic Control (5 Buttons) with LED Display – 3-Minute Delay Shutoff ECO Mode
ECO Mode runs the range hood on the QuietMode™ setting for 10 minutes every hour to remove excess moisture, microscopic particles and odors to promote a cleaner kitchen environment.
3-Level Lighting 3-watt LED light x 2
(CH3830SQBD-1) 29-3/4" x 21-11/16" x 5-7/8" (CH3836SQBD-1) 35-3/4" x 21-11/16" x 5-7/8"
1) Two-Piece Adjustable Duct Cover (CH1120DC-1) 11-13/16" x 10-7/16" x (22” ~ 41")
2) 30" Stainless Steel Back Panel (SSP30) 30" x 1/10" x 32"
3) 36" Stainless Steel Back Panel (SSP36) 36" x 1/10" x 32"
Net CH3830SQD-1 (30”) 40 44
CH3836SQD-1 (36”) 42 49
QuietMode™ 1 2 3 4 5
150 190 230 280 340 400
1.0 1.4 2.8 3.5 4.2 4.5
*One sone is equivalent to the sound of a refrigerator at 40 decibels. **Specifications subject to change without notice.
Gross
23
Page 27
www.goedekers.com
MEASUREMENTS & DIAGRAMS
***All inch measurements are converted from millimeters. Inch measurements are estimated. ***All measurements in ( ) are millimeters.
For Vented Models only: MODEL NO.: CH3830SQB-1 (30”) / CH3836SQB-1 (36”)
-FOR UNDER THE CABINET-
30" = Knockout Holes "A" 36" = Knockout Holes "B"
- FOR WALL MOUNT (WITH OPTIONAL DUCT COVER) -
24
Page 28
www.goedekers.com
For Ductless Models only: MODEL NO.: CH3830SQBD-1 (30”) / CH3836SQBD-1 (36”)
-FOR UNDER THE CABINET-
30" = Knockout Holes "A" 36" = Knockout Holes "B"
- FOR WALL MOUNT (WITH OPTIONAL DUCT COVER) -
25
Page 29
www.goedekers.com
***Hood-Mounting Bracket ***Duct Cover-Mounting Bracke
***Duct Cover Support
26
Page 30
www.goedekers.com
PARTS LIST
For Vented Models only. MODEL NO.: CH3830SQB-1 (30”)
CH3836SQB-1 (36”)
NO. DESCRIPTION MODEL /SIZE PART NO.
1
6” Exhaust Vent Cover (Top)
2 3
3-1/4” x 10” Exhaust
4
3-1/4” x 10” Vent Cover
5
6” Round Plastic Collar LED Light (3W)
6
Control Unit
7
Capacitor (3.5+3.5uF / 350V)
8
LED Light Driver
9 10 11 12 13 14 15 16 17 18 19 20
Motor (102B) Motor (102A) Turbine Impeller (747B) Turbine Impeller (747A) Oil Tunnel Seal Plastic Oil Tunnel Impeller Plastic Cover Safety Screen Safety Screen screws Baffle Filter Stainless Steel Spacer
Optional Duct Cover
NO. DESCRIPTION MODEL /SIZE PART NO.
01 02 03
04 05 06
Hood Mounting Bracket Screws (3/16”x3/8”) x 6
Duct Cover Support x 2 Duct Cover (Inner and Outer) CH1120DC-1 Duct Cover -Mounting Bracket Screws (TS 4 x 6mm) x 4
L1-0241-0001-A L1-0241-0001-B L1-0241-0002-A
L1-0241-0002-B L1-0505-0002
L1-0403-0301 L1-0405-0301 L1-0401-0120-03 L1-04012-D001 L1-0301-0120-102B L1-0301-0120-102A L1-0251-0747-B L1-0251-0747-A
L1-0502-0301
L1-0251-0101 L1-0251-0001 L1-0602-0101 L1-0705-0001 L1-0214-0122 CH3830SQB-1 B101-1630-15
L1-0221-1630 L1-0707-0002 L1-0208-1630
12-16300-61 L1-0203-1630 L1-0708-0002
27
Page 31
www.goedekers.com
For Vented Models only. MODEL NO.: CH3830SQB-1 (30”)
CH3836SQB-1 (36”)
28
Page 32
www.goedekers.com
For Ductless Models only. MODEL NO.: CH3830SQBD-1 (30”)
CH3836SQBD-1 (36”)
NO. DESCRIPTION MODEL /SIZE PART NO.
LED Light (3W)
1 2 3 4 5 6 7 8
9 10 11 12 13 14 15 16
Control Unit Capacitor (1.5uf +2.0uF/ 350V) Motor (102B) Motor (102A) Turbine Impeller (737B) Turbine Impeller (737A) Processor Board Oil Tunnel Seal Plastic Oil Tunnel Impeller Plastic Cover Safety Screen Safety Screen Screws Charcoal Filter Baffle Filter Stainless Steel Spacer CH3830SQBD-1 (30”)
L1-0403-0301 L1-0501-6001 L1-0401-0120-6 L1-0301-0120-102B L1-0301-0120-102A L1-0251-0737-B L1-0251-0737-A L1-0404-6001 L1-0502-0301 L1-0251-0101 L1-0251-0001 L1-0602-0101
L1-0705-0001 L1-0603-0302 L1-0214-0122
B101-1630-15
Optional Duct Cover
NO. DESCRIPTION MODEL /SIZE PART NO.
01 02 03
04 05 06
Hood Mounting Bracket Screws (3/16”x3/8”) x 6
Duct Cover Support x 2 Duct Cover (Inner and Outer) CH1120DC-1 Duct Cover- Mounting Bracket Screws (TS 4 x 6mm) x 4
L1-0221-1630 L1-0707-0002 L1-0208-1630
L1-0203-1630 L1-0708-0002
12-16300-61
29
Page 33
www.goedekers.com
For Ductless Models only. MODEL NO.: CH3830SQBD-1 (30”)
CH3836SQBD-1 (36”)
30
Page 34
www.goedekers.com
CIRCUIT DIAGRAM
For Vented Models only: MODEL NO.: CH3830SQB-1 (30”) / CH3836SQB-1 (36”)
For Ductless Models only: MODEL NO.: CH3830SQBD-1 (30”) / CH3836SQBD-1 (36”)
31
Page 35
www.goedekers.com
TROUBLE SHOOTING
For Vented Models only: MODEL NO.: CH3830SQB-1 (30”) / CH3836SQB-1 (36”)
Issue Possible Cause Solution
After Installation, both motors and lights are not working.
Lights are working, but motor(s) is not.
The range hood is vibrating.
The motor is working, but the lights are not working.
The range hood is not venting out correctly.
Cold air is coming into the home.
The power is not on. Make sure the circuit breaker and the unit’s
power is ON. Use a voltage meter to check the
power supply. The wire connection is not secure. Check and tighten wire connection. The control panel is defective. Replace the control panel. The motor(s) is defective. Replace the motor. The capacitor(s) is defective. Replace capacitor(s). The control panel is defective. Replace the control panel.
The blower system is not secure. The turbine impeller/squirrel cage is
Tighten the turbine impeller/squirrel cage and air
chamber.
Replace the turbine impeller/squirrel cage. not balanced. Hood is not secured in place. Check the installation of hood, tighten the
mounting bracket. LED light fixture(s) is defective.
Replace LED light fixture(s) The light wiring(s) is loose.
The control panel is defective. The range hood is installed outside of
the manufacture recommended clearance.
There is no make-up air inside the house.
Check wire continuity from Control Panel to LED
Driver to LED light fixture(s).
Replace the control panel.
Adjust the clearance between the range hoods
and cook top to 26” to 30”. For Island range
hood, the clearance between the range hoods
and cook top is 30” to 36”.
Open the window to enhance the performance
of the range hood by creating a sufficient make-
up air. Obstacle blocking the pipe work.
Remove all obstacles from the duct work. The pipe size is smaller than the
suggested pipe size. The pipe connection is not properly sealed. The damper is not properly installed or is missing from the installation.
Change the ducting according to the
manufacture suggestion.
Check the pipe installation.
Check the damper installation. The damper is not installed. By installing the damper, it will help to eliminate
air backflow.
32
Page 36
www.goedekers.com
For Ductless Models only: MODEL NO.: CH3830SQBD-1 (30”) / CH3836SQBD-1 (36”)
Issue Possible Cause Solution
After Installation, both motors and lights are not working.
The power is not on. Make sure the circuit breaker and the unit’s
power is ON. Use a voltage meter to check the
power supply. The wire connection is not secure. Check and tighten wire connection. The control panel and processor board wiring are disconnected. The control panel and processor board
Check wire continuity from control panel to
processor board.
Replace the control panel or processor board. is defective.
Lights are working, but motor(s) is not.
The range hood is vibrating.
The motor(s) is defective. Replace the motor. The capacitor(s) is defective. Replace capacitor(s). The control panel or processor board is
Replace the control panel or processing board. defective. The blower system is not secure.
The turbine impeller/squirrel cage is
Tighten the turbine impeller/squirrel cage and air
chamber.
Replace the turbine impeller/squirrel cage. not balanced. Hood is not secured in place. Check the installation of hood, tighten the
mounting bracket.
The motor is working, but the lights are not working.
LED light fixture(s) is defective. The light wiring(s) is loose.
The control panel or processor board is defective.
Replace LED light fixture(s)
Check wire continuity from processor board to
light transformer to LED light fixture(s).
Replace the control panel or processing board.
The range hood is not venting out correctly.
The range hood is installed outside of the manufacture recommended clearance.
There is no make-up air inside the house.
Adjust the clearance between the range hoods
and cook top to 26” to 30”. For Island range
hood, the clearance between the range hoods
and cook top is 30” to 36”.
Open the window to enhance the performance
of the range hood by creating a sufficient make-
up air. Obstacle blocking the pipe work.
Remove all obstacles from the duct work.
Cold air is coming into the home.
The pipe size is smaller than the suggested pipe size. The pipe connection is not properly sealed. The damper is not properly installed or is missing from the installation.
Change the ducting according to the
manufacture suggestion.
Check the pipe installation.
Check the damper installation. The damper is not installed. Installing the damper will help eliminate air
backflow.
33
Page 37
www.goedekers.com
WARRANTY
WARRANTY CERTIFICATE
KOBE Range Hoods (referred to herein as “we”or “us”) warrants to the original purchaser (referred to from defect in workmanship and materials as follows:
TWO-YEAR LIMITED WARRANTY FOR PARTS AND LABOR ON KOBE PREMIUM SERIES:
For two years from the date of your original invoice from a KOBE authorized dealer, we will, at our sole discretion, choose to repair or replace the product free of charge that failed due to manufacturing defects.
It is your sole responsibility to ensure the product is readily accessible for the service technician to perform repairs. The service technician will not, under any circumstance,
remove, alter or modify any fixture built around and/or connected to the product to gain access to perform repairs.
During the two-year Limited Warranty period, additional charges may apply which include but are not limited to:
• Service technician travel charges if the requested service location is 30-miles out of
• Parts shipping expenses
• Un-installation of defective product and Installation of replacement product
herein as “you” or “your”) all products manufactured or supplied by us to be free
KOBE’s authorized service area
ONE-YEAR LIMITED WARRANTY FOR PARTS ON KOBE BRILLIA SERIES:
For one year from the date of your original invoice from a KOBE authorized dealer, we will provide, free of charge, parts to replace those that failed due to manufacturing defects. It is our sole discretion to choose to repair or replace defective parts. It is your sole responsibility for all labor costs associated with this warranty.
Warranty Exclusions:
This warranty does not cover, including but not limited to the following:
a. Improper installation. b. Any repair, alteration, modification not authorized by KOBE. c. Duct alteration, modification and connection. d. Incorrect electric current, voltage or wiring. e. Normal maintenance and service required for the product. f. Consumable parts such as light bulbs and carbon filters. g. Improper usage of the product that it is not intended for, such as commercial use,
outdoor use and multi-family use. h. Normal wear and tear. i. Chips, scratches or dents by abuse or misuse of the product. j. Damages caused by accident, fire, flood and other Acts of God. k. Expenses incurred for service located outside of the designated service area. l. Purchases from unauthorized dealers.
34
Page 38
www.goedekers.com
m. Removal fees of defective product and Installation fees associated with replacement
product.
If we determine that the warranty exclusions listed above apply or if you fail to provide all necessary documentation for warranty service, you will be responsible for all expenses associated with the requested service, including parts, labor, shipping, travelling and any other expense related to the service request.
To qualify for warranty service, you must:
1. Have the ORIGINAL proof of purchase
2. Be the ORIGINAL purchaser of the product
3. Have the model number
4. Have the serial number
5. Have a description of the nature of any defect in the product or part
TO REQUEST WARRANTY SERVICE, PLEASE CONTACT THE KOBE RANGE HOODS SERVICE CENTER:
KOBE SERVICE CENTER Tel: 1-855-800-KOBE (5623) E-mail: kobe@adcoservice.com
35
Page 39
www.goedekers.com
PRODUCT REGISTRATION
Fill in the blanks and keep this paper with the original invoice in a safe place for future service purpose.
1. Date of purchase :
2. Model No. :
3. Serial No. :
For warranty service or spare parts purchase contact:
KOBE Service Center Toll Free: 1-855-800-KOBE (5623) Email: kobe@adcoservice.com
To report a problem, please contact:
Toll Free: 1-877-BUY-KOBE (289-5623) Email: customer.service@koberangehoods.com
For product information contact:
Toll free: 1-877-BUY-KOBE (289-5623) Email: info@koberangehoods.com
Your notes:
36
Page 40
www.goedekers.com
KOBE Range Hoods
11775 Clark Street
Arcadia, CA 91006 USA
http://www.KOBERangeHoods.com
This KOBE hood is made for use in the USA and CANADA only. We do not recommend
using this hood overseas as the power supply may not be compatible and may violate
the electrical code of that country. Using a KOBE hood overseas is at your own risk
and will void your warranty.
Cette hotte KOBE est fabriquée pour usage aux États-Unis et au Canada seulement. Il
n’est pas recommandé d’utiliser cette hotte à l’étranger puisque l’alimentation électrique
pourrait ne pas être compatible et enfreindre le code de l’électricité de ce pays. L’usage
de la hotte KOBE à l’étranger est à votre propre risque et la garantie sera annulée.
Esta campana de extracción KOBE ha sido fabricada para ser utilizada únicamente en
EE.UU. y CANADÁ. No recomendamos la utilización de esta campana en el extranjero
debido a que la fuente de energía podría no ser compatible y podría violar el código
eléctrico de dicho país. Utilizar una campana KOBE en el extranjero será a su
propio riesgo y anulará la garantía.
VER.140219
Information subject to change without notice.
37
Loading...
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use