KOBE INX2730SQB-700-1Brillia Series, Brillia Series INX2730SQB-700-1 Installation Instructions And Operation Manual

KOBE Range Hoods

Brillia Series

Model No.

INX2730SQB-700-1

INSTALLATION INSTRUCTIONS

AND OPERATION MANUAL

IMPORTANT

READ THIS FIRST

READ BEFORE INSTALLATION

1. Carefully check all contents of packages;

2. Thoroughly inspect the unit for any cosmetic damages or

defects;

3. Test the unit before installation;

4. Have a certified contractor/electrician do the installation.

IF THERE IS ANY PROBLEM:

1. DO NOT INSTALL THE UNIT AND KEEP ALL ORIGINAL

PACKAGING MATERIAL.

2. Have your original invoice as proof of purchase and

product serial number ready.

3. Call 1-877-BUY-KOBE (289-5623); or e-mail to

[e-mail]

NO RETURN, NO REFUND, NO EXCHANGE IF:

1. PRODUCT HAS BEEN INSTALLED

2. KNOCK-OUT HOLES HAVE BEEN PUNCTURED

3. MISSING ORIGINAL PACKAGING MATERIAL AND/OR PARTS

to report the problem.

- READ AND SAVE THESE INSTRUCTIONS -

CONTENTS

[ENGLISH]

IMPORTANT SAFETY INSTRUCTIONS ................................................................................... 2

COMPONENTS OF PACKAGE ................................................................................................. 4

INSTALLATION ......................................................................................................................... 5

OPERATING INSTRUCTIONS .................................................................................................. 9

MAINTENANCE ...................................................................................................................... 10

SPECIFICATIONS ................................................................................................................... 11

MEASUREMENTS & DIAGRAMS ........................................................................................... 12

PARTS LIST ............................................................................................................................ 14

CIRCUIT DIAGRAM ................................................................................................................ 16

TROUBLE SHOOTING............................................................................................................ 17

DISCLAIMER ........................................................................................................................... 18

WARRANTY ............................................................................................................................ 19

WARRANTY INFORMATION FORM....................................................................................... 21

- READ ALL INSTRUCTIONS CAREFULLY BEFORE STARTING -

AL L W IR IN G MU S T BE D O N E B Y A P R O FE SS IO N AL A ND I N

AC CO RD A N C E W I T H NA TI O NA L AN D LO C AL E LE C TR IC AL C O DE S

1

IMPORTANT SAFETY INSTRUCTIONS

- PLEASE READ THIS SECTION CAREFULLY BEFORE INSTALLATION -

WARNING

1) Installation and electrical wiring must be done by qualified professionals and in accordance with all
applicable codes and standards, including fire-rated construction.

2) When cutting or drilling into wall or ceiling, be careful not to damage electrical wiring or other hidden
utilities.

3) Ducted fans must be vented to the outside.
a) Before servicing or cleaning unit, open the light panel and SWITCH POWER OFF AT SERVICE

PANEL.

b) Clean all grease laden surfaces frequently. To reduce the risk of fire and to disperse air

properly, make sure to vent air outside. DO NOT vent exhaust air into wall spaces, attics, crawl
spaces or garages.

NOTE - This warranty is invalid without an authorized agent’s receipt or if unit is

- KOBE RANGE HOODS will not be held responsible for any damages to

: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR PERSONAL

INJURY, OBSERVE THE FOLLOWING:

damaged due to misuse, poor installation, improper use, mistreatment,
negligence or any other circumstances beyond the control of KOBE
RANGE HOODS authorized agents. Any repair carried out without the
supervision of KOBE RANGE HOODS authorized agents will
automatically void the warranty.

personal property or real estate or any bodily injuries whether caused
directly or indirectly by the range hood.

WARNING

- Keep all fan, baffle/spacer/filter/oil tunnel/oil container and grease-laden surfaces clean. Grease
should not be allowed to accumulate on fan, baffle/spacer/filter/oil tunnel/oil container.

- Always turn hood ON when cooking.

- Use high settings on cooking range ONLY when necessary.

- Do not leave cooking range unattended when cooking.

- Always use cookware and utensils appropriate for the type and amount of food prepared.

- Use this unit only in the manner intended by the manufacturer.

- Before servicing, switch power off at service panel and lock service panel (if possible) to prevent
power from switching on accidentally.

-

Clean ventilating fan frequently.

:

TO REDUCE THE RISK OF PERSONAL INJURY IN THE EVENT OF A RANGE
TOP GREASE FIRE:

2

What to Do In The Event Of a Range Top Grease Fire

ELECTRICAL SHOCK HAZA

RD – Can result in serious injury or

• SMOTHER FLAMES with a tight fitting lid, cookie sheet, or metal tray, and then turn off the burner.
KEEP FLAMMABLE OR COMBUSTIBLE MATERIAL AWAY FROM FLAMES. If the flames do not
go out immediately, EVACUATE THE AREA AND CALL THE FIRE DEPARTMENT or 911.

• NEVER PICK UP A BURNING PAN – You May Get Burned.

• DO NOT USE WATER, including wet dishcloths or towels – a violent steam blast will result.

• Use an extinguisher ONLY if:
a) You have a Class A, B, C extinguisher and know how to operate it.
b) The fire is small and contained in the area where it started.
c) The fire department has been called.
d) You can fight the fire with your back to an exit.

What to Do If You Smell Gas

-

Extinguish any open flame.

-

Do not try to turn on the lights or any type of appliance.

-

Open all doors and windows to disperse the gas. If you still smell gas, call the Gas Company and
Fire Department right away.

CAUTION

1. For general ventilation use only. Do not use to exhaust hazardous or explosive materials and
vapors.

2. To reduce the risk of fire, use only metal ductwork. Sufficient air is needed for proper combustion
and exhausting of gases through the flue (chimney) to prevent back drafting.

3. Follow the heating equipment manufacturer’s guideline and safety standards such as those
published by the National Fire Protection Association (NFPA), and the American Society for
Heating, Refrigeration and Air Conditioning Engineers (ASHRAE), and code authorities.

4. Activating any switch on may cause ignition or an explosion.

5. Due to the size and weight of this hood, two people installation is recommended.

death. Disconnect appliance from electric power before servicing.
If equipped, the fluorescent light bulb contains small amounts of
mercury, which must be recycled or disposed of according to
Local, State, and Federal Codes.

3

COMPONENTS OF PACKAGE

KOBERangehoods.com

(Must keep all material for returns or refunds)

Range Hood Box

{A} Brillia Range Hood
{B} Warranty Registration Card
{C} Instruction Manual (WEBSITE)
{D} Baffle Filter – 2
{E} 6” Round Plastic Collar – 1
{F} Liner (Sold Separately)

{A}

{D} {E}

{F}

Liner (Sold Separately)

{B} {C}

For the operation
manual, please refer to
our website:

{D} {E}

-

FOR MORE INFORMATION, PLEASE VISIT OUR WEBSITE www.KOBERangeHoods.com OR
CONTACT KOBE RANGE HOODS AT [phone].

4

INSTALLATION

TABLE 1

PLEASE READ ENTIRE INSTRUCTIONS BEFORE PROCEEDING

Calculation before Installation

To calculate installation, please refer to TABLE 1. (All calculation in inches.)

- FOR UNDER THE CABINET -

A = Height of Floor to Ceiling
B = Height of Floor to Counter Top

(Standard: 36")

C = Height of Counter Top to Wood Frame

Bottom (Recommended 26" to 30")

D = Height of Wood Frame

SAFETY WARNING

HOOD MAY HAVE VERY SHARP EDGES; PLEASE WEAR PROTECTIVE GLOVES IF
REMOVING ANY PARTS FOR INSTALLING, CLEANING OR SERVICING.

NOTE: BE CAREFUL WHEN USING ELECTRICAL SCREWDRIVER, DAMAGE TO THE HOOD

MAY OCCUR.

5

- For Insert installation -

screws.

Preparation Before Installation

NOTE: TO AVOID DAMAGE TO YOUR HOOD, PREVENT
DEBRIS FROM ENTERING THE VENT OPENING.

•

Decide the location of the venting pipe from the hood to
the outside. Refer to Figure 1.

•

A straight, short vent run will allow the hood to perform
more efficiently.

•

Try to avoid as many transitions, elbows, and long run
as possible. This may reduce the performance of the
hood.

•

Temporarily wire the hood to test for proper operation
before installing.

•

Important: Peel protective film off the hood, if any.

•

Use duct tape to seal joints between pipe sections.

CAUTION

necessary to install the hood, turn off the power in an
electric range at the main electrical box. SHUT OFF
THE GAS BEFORE MOVING A GAS RANGE. And use a
protective covering to protect cook top and/or
countertop from damage.

: If moving the cooking range is

Figure 1

Figure 2

Custom Hood Preparation

1. The custom hood frame must be sized to shape and the
weight of the insert. Refer to Measurements and
Diagrams on Page 12.

2.

Install 6” Round Plastic Collar

Refer to Figure 2.

3. It must have a sturdy base (1/2 inch thick plywood
recommended) to sustain the weight of insert.

4. If an optional liner will be installed, the side of the wood
cabinet must be sturdy (1/2 inch thick plywood
recommended).

5. It is recommended to install a rear and front stud
support. Refer to Figure 3. The stud supports are
located 1-1/2” up from the base of the wood frame.

using 2 attached

Liner Installation

6. The custom/wood hood must have a sturdy base to
accommodate the cut-out for the inset. The base must be
recessed to accommodate the height of the liner (See
liner dimension on Page 13)

7. Secure the liner to the bottom of the base using screws
(not included) appropriate for the size and material of your
wood frame.

8. Position the liner so that it aligns with the back edge of
the custom wood frame. Use a pen to trace the outline of
the pre-cut area. Remove the liner and proceed to Hood
Preparation before Installation on Page 7.

9. Install the liner with 5 screws (not provided).

6

Figure 3

Wiring to Power Supply

es before installing insert.

connect the ducting on the hood to the ductwork above.

SAFETY WARNING

RISK OF ELECTRICAL SHOCK. THIS RANGE HOOD MUST
BE PROPERLY GROUNDED. MAKE SURE THIS IS DONE
BY QUALIFIED ELECTRICIAN IN ACCORDANCE WITH ALL
APPLICABLE NATIONAL AND LOCAL ELECTRICAL
CODES. BEFORE CONNECTING WIRES, SWITCH POWER
OFF AT SERVICE PANEL AND LOCK SERVICE PANEL TO
PREVENT POWER FROM BEING SWITCHED ON
ACCIDENTALLY.

10. Temporarily wire the hood to test for proper operation
before installing. If the insert does not operate, check
the circuit breaker or house fuse. If the insert is still not
working, disconnect the power supply and check the
continuity of all wiring connections.

11. Connect electrical wires.

12. Connect three wires (black, white and green) to house
wires and cap with wire connectors. Connect wires
according to their colors (i.e. black to black, white to
white, and green to green). See Figure 4.

13. Store wires in the wiring box.

Note: Connect all electrical wir
DO NOT turn on the power until installation is complete.

Figure 4

Figure 5

Duct Work Installation

14. Use 6” steel pipe (follow building codes in your area) to
Use duct tape to seal and secure joints as shown in

Figure 5.

15. Please refer to local codes for the usage of a damper
(not included).

Hood Preparation Before Installation

CAUTION

to install the hood, turn off the power in an electric range at
the main electrical box. SHUT OFF THE GAS BEFORE
MOVING A GAS RANGE.

16. Determine and mark the centerlines on the base of the
wood frame where the insert will be installed.

17. Determine and make all necessary cuts in the wall or
ceiling for the ductwork. Note: Install the duct work
before installing the insert.

18. Cut out the opening where the insert will be installed.

Figure 6

: If moving the cooking range is necessary

Figure 6

7

Hood Installation

on each side of the insert.

19. Slide the hood to the opening where it will be installed.
Two hooks will lock to temporarily hold the hoods’
weight. Figure 7

20. Locate the screw holes (4)
Adjust the level of the hood casing support according to
the thickness of the base (1/2 thickness plywood
recommended – Refer to Figure 3).

21. Secure the hood using screws holes that are located in
front and back of unit (Screws not provided) Figure 8

22. Make sure the hood casing support is secure before
releasing.

CAUTION

RELEASING.

: MAKE SURE HOOD IS SECURE BEFORE

Final Assembly

23. Install Baffle Filters. Insert the filters towards the
back of the unit and push up.

24. Make sure the Baffle Filters are secure before
releasing.

Figure 7

Figure 8

8

OPERATING INSTRUCTIONS

This KOBE hood is equipped with five electronic push buttons with LED indicator, double powerful
centrifugal squirrel cage with baffle filters, two bright 3-watt LED lights.

The five control buttons are Power Control (On/Off), Speed Control (High, Low, & QuietMode™), Light
Control, and Change Filter Indicator. Refer to Figure 9.

Change Filter
Indicator

LED Light
Control

Figure 9
Note: For best results, turn hood to Low prior to any preparation or cooking. Adjust speed as needed.
Power Control

Press Power Control to turn On/Off the hood.

This unit equipped with 3-minute delay shutoff. To activate this feature, press Power
Control button once, panel LED lights will flash and power will be completely shut off after 3
minutes.

Press Power Control button twice, the fans will be shut off immediately.

Speed Control

Press Speed Control to activate Q - QuietMode™, L - Low, & H - High Speed.

Speed
Control

Power Control

Light Control

(Light control is separate from ON/OFF control. Turning power off will not turn lights off.)
Press Light control to turn lights ON.

9

Baffle Filter Change Indicator

The indication under symbol will indicate when baffle filter needs cleaning.
Remove to clean the baffle filter.

(To purchase replacement filters, please contact your local KOBE dealer or call 626-775-8880)

MAINTENANCE

SAFETY WARNING

NEVER PUT YOUR HAND INTO AREA HOUSING THE FAN WHILE THE FAN IS
OPERATING.

Cleaning Hood Surface

CAUTION

:

NEVER USE ABRASIVE CLEANERS, PADS, OR CLOTHS. DO NOT
USE PAPER TOWEL ON STAINLESS STEEL.

For optimal operation, clean range hood and all baffle/spacer/filter/oil tunnel/oil container regularly.
*** Regular care will help preserve the appearance of the hood.

1. Use only mild soap or detergent solutions. Dry surfaces using soft cloth.

2. If hood looks splotchy (stainless steel hood), use a stainless steel cleaner to clean the surface
of the hood. Avoid getting cleaning solution onto or into the control panel. Follow directions of
the stainless steel cleaner. Caution: Do not leave on too long as this may cause damage to
hood finish. Use soft towel to wipe off the cleaning solution, gently rub off any stubborn spots.
Use dry soft towel to dry the hood.

3. DO NOT allow deposits to accumulate or remain on the hood.

4. DO NOT use ordinary steel wool or steel brushes. Small bits of steel may adhere to the surface
and cause rusting.

5. DO NOT allow salt solutions, disinfectants, bleaches, or cleaning compounds to remain in
contact with stainless steel for extended periods. Many of these compounds contain chemicals,
which may be harmful. Rinse with water after exposure and wipe dry with a clean lint free cloth.

To Clean Baffle Filter

1. Remove all the baffle filters.

2. Wash with warm soapy water. Dry thoroughly before returning into place.

10

SPECIFICATIONS

MODEL / SIZE INX2730SQB-700-1
COLOR 18-Gauge Commercial Stainless Steel

CONSUMPTION / AMPERE 120W / 3.3A
VOLTAGE 120V 60Hz

NUMBER OF MOTORS 1
FAN TYPE: CENTRIFUGAL Double Horizontal Squirrel Cage
EXHAUST Top 6” Round
CONTROLS 5 / Mechanic Push Button

- 3-Minute Delay Shutoff
HALOGEN LIGHTS 3W-LED x 2
HOOD DIMENSION

(W X D X H)
OPTIONAL ACCESSORIES

(W X D X H)
HOOD WEIGHT (lbs) Net Gross

Blower Air Capacity (CFM)
Sone 1.0 2.2 5.6

27-1/2” x 11-3/16” x 10-3/8”

Liner: INL36211A (36” X 21” X 2”)

INX2730SQB-700-1

QuietMode™ Low High

300 440 750

23.6 30.2

* One Sone is equivalent to 40 decibels.
**Specifications subject to change without notice.

11

11

-

3/16” (284)

10

-

3/8” (264)

MEASUREMENTS & DIAGRAMS

27-1/2” (699)

 All ( ) are in millimeter.
 All inch measurements are converted from millimeters. Inch measurements are estimated.

MODEL NO: INX2730SQB-700-1

Bottom View

Front View

12

Stainless Steel Liner (Sold Separately)
Model No. INL36211A

13

PARTS LIST

MODEL NO: INX2730SQB-700-1

*Liner Sold Separately

14

INX2730SQB-700-1

Liner
(Sold Separately)

15

CIRCUIT DIAGRAM

MODEL NO.: INX2730SQB-700-1

16

TROUBLE SHOOTING

Issue

Possible

Cause

Solution

After
Installation,
both motors
and lights are
not working.

Lights are
working, but
motor(s) is
not.

The range
hood is
vibrating.

The power is not on.
The wire connection is not secure. Check and tighten wire connection.

The control panel and processor
board wiring are disconnected.
The control panel and processor
board is defective.
The motor(s) is defective. Replace the motor.
The capacitor(s) is defective. Replace capacitor(s).

The control panel or processor
board is defective.

The blower system is not secure.
The turbine impeller/squirrel cage is

not balanced.
Hood is not secured in place.

Make sure the circuit breaker and the unit’s
power is ON. Use a voltage meter to check
the power supply.

Check wire continuity from control panel to
processor board.
Replace the control panel or processor
board.

Replace the control panel or processing
board.

Tighten the turbine impeller/squirrel cage
and air chamber.

Replace the turbine impeller/squirrel cage.
Check the installation of hood, tighten the

mounting bracket.

The motor is
working, but
the lights are
not working.

The range
hood is not
venting out
correctly.

Cold air is
coming into
the home.

LED driver is defective Replace LED Driver
LED light fixture(s) is defective Replace LED light fixture(s)

The light wiring(s) is loose.

The control panel or processor
board is defective.
The range hood is installed outside
of the manufacture recommended
clearance.

There is no make-up air inside the
house.

Obstacle blocking the pipe work.
The pipe size is smaller than the

suggested pipe size.
The pipe connection is not properly
sealed.
The damper is not properly installed
or is missing from the installation.

The damper is not installed.

Check wire continuity from processor board
to light transformer to LED light fixture(s).

Replace the control panel or processing
board.
Adjust the clearance between the range
hoods and cook top to 26” to 30”. For Island
range hood, the clearance between the
range hoods and cook top is 30” to 36”.
Open the window to enhance the
performance of the range hood by creating
a sufficient make-up air.

Remove all obstacles from the duct work.
Change the ducting according to the

manufacture suggestion.
Check the pipe installation.

Check the damper installation.
Installing the damper will help eliminate air

backflow.

17

DISCLAIMER

1. CAREFULLY INSPECT ALL ITEMS FOR DAMAGES BEFORE ACCEPTING DELIVERY. NOTE

ANY DAMAGES ON THE FREIGHT BILL OR EXPRESS RECEIPT. REQUEST NAME AND
SIGNATURE OF THE CARRIER’S AGENT AND KEEP COPY TO SUPPORT YOUR CLAIM.

Upon acceptance of items, owner assumes responsibility for its safe arrival. Report damages to the
carrier and file a claim immediately. Failure to do so may result in the denial of your claim. The
carrier will furnish you with necessary forms for filing a claim.

DAMAGES CAUSED DURING TRANSIT ARE NOT COVERED UNDER OUR WARRANTY.

2. PLEASE INSPECT CONTENTS OF PACKAGE(S) CAREFULLY UPON RECEIVING!
We must be notified in writing of any damages and/or missing parts within the allocated days upon

your receipt of package(s). Contact your local KOBE dealer or distributor or call KOBE for the time
limit.

CLAIMS WILL NOT BE ACCEPTED AFTER THE ALLOCATED DAYS.

NOTE: ITEMS WERE THOROUGHLY TESTED AND CAREFULLY PACKED IN OUR FACTORY

BEFORE SHIPPING.

3. Products must be returned in good working condition with ALL original parts and documentation

packed in ALL original cartons, fillers and shipping cartons. A restocking fee of 25% will be charged
for all approved return(s).

EXCHANGES OR RETURNS MAY NOT BE ACCEPTED IF ANY PACKAGING IS MISSING.

4. MAKE SURE TO INSPECT THE HOOD FOR DAMAGES AND DEFECTS BEFORE

INSTALLATION. Appearance flaws of the hood found after installation and not affecting hood

performance is not covered under our warranty for returns or exchanges. Service visits not covered
under warranty will carry a service charge.

1.

2.

Before Installation: Return for exchange or refund (please see above for acceptable

returns).

After Installation: NO exchange or refund.

18

WARRANTY

WARRANTY CERTIFICATE

KOBE Range Hoods (referred to herein as “we” or “us”) warrants to the original purchaser
(referred to herein as “you” or “your”) all products manufactured or supplied by us to be free
from defect in workmanship and materials as follows:

TWO-YEAR LIMITED WARRANTY FOR PARTS AND LABOR ON KOBE PREMIUM /
BRILLIA SERIES:

For two years from the date of your original invoice from a KOBE authorized dealer, we will, at
our sole discretion, choose to repair or replace the product free of charge that failed due to
manufacturing defects.

It is your sole responsibility to ensure the product is readily accessible for the service
technician to perform repairs. The service technician will not, under any circumstance,

remove, alter or modify any fixture built around and/or connected to the product to gain
access to perform repairs.

During the two-year Limited Warranty period, additional charges may apply which include but
are not limited to:

• Service technician travel charges if the requested service location is 30-miles out of
KOBE’s authorized service area

• Parts shipping expenses

• Un-installation of defective product and Installation of replacement product

Warranty Exclusions:

This warranty does not cover, including but not limited to the following:

a. Improper installation.
b. Any repair, alteration, modification not authorized by KOBE.
c. Duct alteration, modification and connection.
d. Incorrect electric current, voltage or wiring.
e. Normal maintenance and service required for the product.
f. Consumable parts such as light bulbs and carbon filters.
g. Improper usage of the product that it is not intended for, such as commercial use,

outdoor use and multi-family use.

h. Normal wear and tear.
i. Chips, scratches or dents by abuse or misuse of the product.
j. Damages caused by accident, fire, flood and other Acts of God.
k. Expenses incurred for service located outside of the designated service area.
l. Purchases from unauthorized dealers.
m. Removal fees of defective product and Installation fees associated with replacement

product.

If we determine that the warranty exclusions listed above apply or if you fail to provide all
necessary documentation for warranty service, you will be responsible for all expenses
associated with the requested service, including parts, labor, shipping, travelling and any other
expense related to the service request.

19

To qualify for warranty service, you must:

1. Have the ORIGINAL proof of purchase

2. Be the ORIGINAL purchaser of the product

3. Have the model number

4. Have the serial number

5. Have a description of the nature of any defect in the product or part

TO REQUEST WARRANTY SERVICE, PLEASE CONTACT THE KOBE RANGE HOODS
SERVICE CENTER:

KOBE SERVICE CENTER (USA ONLY)
Tel: [phone]-KOBE (5623)
E-mail: [e-mail]

For Service in Canada or
To report a problem, please contact:
Tel: [phone]
Email: [e-mail]

20

WARRANTY INFORMATION FORM

Fill in the blanks and keep this paper with the original invoice in a
safe place for future service purpose.

1. Date of purchase :

2. Model No. :

3. Serial No. :

For warranty service or spare parts purchase contact:

KOBE Service Center (USA ONLY)
Toll Free: 1-855-800-KOBE (5623)
Email: [e-mail]

For service in Canada and to report a problem, please
contact:

Phone: [phone]
Email: [e-mail]

Your notes:

21

This KOBE hood is made for use in the USA and CANADA only. We do not

recommend using this hood overseas as the power supply may not be

Using a KOBE

Unis et au Canada

l’étranger puisque

l’alimentation électrique pourrait ne pas être compatible et enfreindre le code de

à l’étranger est à votre

a sido fabricada para ser utilizada

No recomendamos la utilización de esta

campana en el extranjero debido a que la fuente de energía podría no ser

Utilizar una

en el extranjero será a su propio riesgo y anulará la

KOBE Range Hoods

11775 Clark Street

Arcadia, CA 91006 USA

www.KOBERangeHoods.com

compatible and may violate the electrical code of that country.

hood overseas is at your own risk and will void your warranty.

Cette hotte KOBE est fabriquée pour usage aux États­seulement. Il n’est pas recommandé d’utiliser cette hotte à

l’électricité de ce pays. L’usage de la hotte KOBE

propre risque et la garantie sera annulée.

Esta campana de extracción KOBE h
únicamente en EE.UU. y CANADÁ.

compatible y podría violar el código eléctrico de dicho país.

campana KOBE
garantía.

Information subject to change without notice.
VER 150312