Your unit can be installed to meet ADA regulations when and where applicable. Refer to
Federal Register, Volume 56, No 144 28 CFR Part 36.
You are responsible for the safe operation of this unit.
IMPORTANT. RETAIN FOR FUTURE REFERENCE. READ CAREFULLY.
IMPORTANTE. GUÁRDELO PARA FUTURAS CONSULTAS. LEER ATENTAMENTE.
IMPORTANT. À CONSERVER POUR INFORMATION. À LIRE ATTENTIVEMENT.
WICHTIG. ZUR SPÄTEREN BEZUGNAHME AUFBEWAHREN. BITTE SORGFÄLTIG
DURCHLESEN.
Koala Kare Products ǁ 6982 S Quentin St. ǁ Centennial, CO 80112 Toll Free: 888.733.3456 ǁ 303.539.8300 ǁ Fax: 303.539.8399
www.koalabear.com
OPERATING INSTRUCTIONS
Please Note:
To assure proper installation, it is suggested that a qualied person or carpenter install the Koala
Kare Baby Changing Station. Koala Kare Products will not be responsible if the station is not
installed properly.
Koala Kare Baby Changing Stations have been tested to hold a substantial static load. The
unit must be attached to a permanent wall that is capable of holding a substantial load. The
maximum recommended total weight for this baby changing station (including baby and parcel
bag) is 60 lbs. Excessive weight may cause a hazardous or unstable condition to exist.
Restraint System: To fasten the waist restraint strap, place strap around child’s midsection, and
push spring tabs into buckle until both spring tabs lock in place with an audible “click”. Straps
can be adjusted to make strap tighter or looser as required.
Inspection Criteria:
A properly maintained Baby Changing Station:
- Opens and closes smoothly.
- Has both ends of a functioning, non-frayed strap: buckle clicks when closed and strap is
attached at both ends of unit.
- Provides a clean, convenient place for customers to attend to their children.
Measuring
Tape
GlovesPhillips Head
Screwdriver
Drill1/8” Drill Bit
(regular)
TOOLS NEEDED
HARDWARE PROVIDED
Four 1/4”x 3” Phillips
Panhead Wood Screws
Four ¾” x ¼” Flat WashersTwo
Stud
Finder
LevelPencil
7/32” Drill Bit
(masonry)
Screw Hole Plugs
1/2” Drill Bit
(masonry)
1
INSTALLATION INSTRUCTIONS
Oval Baby Changing Station
Model Number KB208
Step 1.
Remove the station from the shipping container and check for any freight damage. Identify the best
location for installing the unit. Hold the unit in place and open the bed. Make sure you have taken the
operating clearance into consideration.
Step 2.
Determine the best method of mounting based
on the type of wall. You may have to purchase
toggles.
Step 3.
The oval unit has four mounting holes provided
in the back wall, positioned on a 16” (406 mm)
stud center. If possible, locate the wood or
metal studs for fastening the unit in the desired
location. If the walls do not have studs on 16”
center as outlined, make sure at least one side
of the unit is installed into the stud. Use toggles
for holes on the opposite side.
Step 4.
Find the stud where you will be attaching the left side of the unit to the wall. Measure up from the oor
42¼” (1,073 mm), at the center of the stud, and mark the wall. Mark remaining holes using a measuring
tape to make sure the holes are precisely positioned. Hold unit in place to verify. Use a 1/8” drill bit to
make pilot holes then use four ¼” x 3” panhead wood screws with washers (supplied) to secure the unit
to the studs.
If the wall surface is masonry or tile over studs, use a 7/32” masonry drill bit for the pilot hole until you
hit the stud. Change bit to 1/8” regular drill bit. Use four ¼” x 3” panhead wood screws with washers
(supplied).
If the wall has wood studs that are not on 16” (406 mm) centers, has metal studs or an underlying
surface of concrete block, drill with a ½” masonry bit. (You may have to purchase toggles before
installing.) You must allow a minimum of inside wall space for toggles to turn, depending on toggles
used. Insert and tighten toggles.
Step 5.
Once the unit has been secured to the wall, use the two screw hole plugs provided to cap the upper two
mounting hole recesses. Position the plug over the recess and push it into place using hand pressure.
Do not hammer the plug in as it will damage the plug. Once the plug is ush with the surface stop
pushing and install the second one.
Step 6.
Position Koala sign (supplied) on the outside of the restroom door. Replacement parts can be purchased
from your local distributor or by calling toll free 888.733.3456 or 303.539.8300.
2
ASTM F 2285-04
WARNING: Never leave child
unattended.
WARNING: Avoid serious injury from
falling or sliding out. Always use restraint system.
WARNING: Designed for Infants Only.
Age up to 3.5 years and weighing less than 50
lbs. Keep one hand on the child at all times.
Parcels or accessory items, or both, placed on
the unit may cause the unit to become unstable.
ATTENTION : Ne laissez jamais un
enfant sans surveillance.
ATTENTION : Évitez les blessures
occasionnées par une chute ou une glissade.
Utilisez toujours le système de retenue.
ATTENTION : Conçue uniquement
pour les jeunes enfants. Jusqu’à 3 ans et demi
et moins de 50 lb (23 kg). Conservez une main
sur l’enfant à tout moment.
Tout paquet ou accessoire placé sur la table
peut créer un déséquilibre.
ADVERTENCIA: No deje nunca al
niño desatendido.
ADVERTENCIA: Evite que el niño se
lesione por caerse o resbalarse del cambiador
Use siempre el sistema de sujeción.
ADVERTENCIA: Diseñado
exclusivamente para bebés. Hasta 3 años y
medio de edad y con un peso inferior a 50
libras (22,5 kg aproximadamente). Mantenga
siempre al niño sujeto con una mano.
Colocar paquetes o accesorios, o ambas
cosas, encima del cambiador puede provocar
que se desestabilice.
WARNUNG: Das Kind niemals
unbeaufsichtigt lassen.
WARNUNG: Ernsthafte Verletzungen
durch Herausfallen oder Herausrutschen
verhindern. Immer das Rückhaltesystem
verwenden.
WARNUNG: Dieses Produkt ist
nur für Kleinkinder bis zu 3 1/2 Jahren und
einem Gewicht von höchstens 50 lbs. (23 kg)
vorgesehen. Das Kind immer mit einer Hand
festhalten.
Durch Ablegen von Päckchen und Zubehör auf
der Wickelstation kann diese instabil werden.
3
Loading...
+ 8 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.