Two 5/8” Phillips Pan Head Machine ScrewsOne Truss Head Wood Screw
Tools Required:
Phillips Head Screwdriver or 1/8” Allen Wrench
1. Open Baby Changing Station. Remove the
screws that secure the old strap to the unit.
Discard old strap and screws.
2. Position the new strap on the unit with the
buckle towards the liner dispenser. (See Image).
3. For all models, take one of the Phillips Pan
Head Machine Screws. Insert it through the hole
in the chafe tab and into the hole in the front of
the bed. Secure the screw into the screw insert.
4. Repeat step 3 for the other end of the strap.
For KB200 model use the other Phillips Pan Head
Machine Screw. For KB100 and KB110 models
use the Truss Head Wood Screw.
5. Ensure that the strap is buckled. Clean up
mess and close unit.
®
Koala Kare Products ǁ 6982 S Quentin St. ǁ Centennial, CO 80112 Toll Free: 888.733.3456 ǁ 303.539.8300 ǁ Fax: 303.539.8399
www.koalabear.com
P/N 496 January 2011
INSTRUCCIONES PARA REMPLAZAR LA CORREA
KB100 KB110 KB200
Herraje Suministrado
KB100, KB110 y KB200
P/N 885-KIT
Dos 5/8” Tornillo Tirafondo Cabeza Plana
Uno Tornillo Tirafondo Cabeza Philips
Philips
Herramientas necesarias:
Destornillador de estrella o llave Allen de 1/8 de
pulgada (0,3 cm)
1. Abra la base del cambiador de pañales. Quite
los tornillos que aseguran la correa vieja a la
unidad. Quite la correa vieja y los tornillos.
2. Coloque la nueva correa en la unidad con
la hebilla hacia el dispensador de protectores.
(Véase la imagen).
3. Para todos los modelos tome uno de los
tornillos tirafondo cabeza plana Philips. Insértelo
por el oricio de la hendidura de encaje y por el
oricio en la parte delantera de la cama. Asegure
el tornillo en su lugar.
4. Repita el paso 3 para el otro extremo de la
correa. Para el modelo KB200 use el tornillo
tirafondo cabeza plana Philips. Para los modelos
KB100 y KB110 use el tornillo tirafondo cabeza
Philips
.
5. Asegúrese de que la correa está abrochada.
Limpie y cierre la unidad.
®
Koala Kare Products ǁ 6982 S Quentin St. ǁ Centennial, CO 80112 Toll Free: 888.733.3456 ǁ 303.539.8300 ǁ Fax: 303.539.8399
www.koalabear.com
P/N 496 Enero 2011
INSTRUCTIONS DE REMPLACEMENT DE LA SANGLE
KB100 KB110 KB200
Visserie Fournie
Deux 5/8” Vis de machine de tête de
casserole de Phillips
Outils nécessaires :
Tournevis cruciforme ou clé hexagonale 1/8 po
(3,2 mm)
1. Ouvrez la table à langer. Retirez les vis servant
à xer l’ancienne sangle à la table. Jetez
l’ancienne sangle et les vis.
2. Positionnez la nouvelle sangle sur la table à
langer, boucle vers le distributeur d’alaises. (Voir
illustration).
Une Vis en bois principale de botte
KB100, KB110 et KB200
RÉF. 885-KIT
3. Pour tous les modèles prenez une des vis
de machine de tête de casserole de Phillips.
Insérez-la dans le trou de la xation et dans le
trou à l’avant du lit. Vissez la vis dans l’orice
d’insertion pour vis.
4. Répétez l’étape 3 pour l’autre extrémité de
la sangle. Pour la modèle KB200 utiliser la vis de
machine de tête de casserole de Phillips. Pour
les modèles KB 100 et KB 110 utiliser la vis en
bois principale de botte.
5. Vériez que la sangle est bien bouclée.
Débarrassez la table à langer de tous les débris
et fermez-la.
®
Koala Kare Products ǁ 6982 S Quentin St. ǁ Centennial, CO 80112 Toll Free: 888.733.3456 ǁ 303.539.8300 ǁ Fax: 303.539.8399
www.koalabear.com
P/N 496 Janvier 2011
ANLEITUNG ZUM AUSTAUSCHEN DES GURTES FÜR
KB100, KB110 und KB200
P/N 885-KIT
KB100 KB110 KB200
Befestigungsmaterial beiliegend
Kreuzschlitz-Flachkopf-Schrauben, US-
Ein Linsenkopf-Kreuzschlitz-Schraube
Metallgewinde, Zwei 5/8
Erforderliche Werkzeuge:
Kreuzschlitzschraubendreher oder 1/8” bzw. 3 mm
Inbusschlüssel
1. Babywickeltisch bis zur Horzontal-Lage
aufklappen. Die zwei alten Gurthälften mittels Lösen
der alten Schrauben entfernen. Gurt und Schrauben
entfernen.
2. Neuen Gurt so an der Station befestigen, dass
die Schnalle in Richtung des Auagenspenders
liegt. (Siehe Bild).
3. Für alle Modelle eine der zuvor entfernten
Schrauben Kreuzschlitz-Flachkopf-Schrauben,
US-Metallgewinde, 2x 5/8. Schraube durch das
Loch in der Gurtlasche und in das Loch an der
Vorderseite der Auage einführen. Schraube im
Schraubeneinsatz festdrehen.
4. Schritt 3 am anderen Gurtende wiederholen.
Bei de Modell KB200 benutzen Sie bitte die
Schrauben Kreuzschlitz-Flachkopf-Schrauben, USMetallgewinde, 2x 5/8. Bei den Modellen KB100
und KB110 benutzen Sie bitte die LinsenkopfKreuzschlitz-Schraube.
5. Sicherstellen, dass der Gurt eingeschnallt ist.
Aufräumen und Station zumachen.
®
Koala Kare Products ǁ 6982 S Quentin St. ǁ Centennial, CO 80112 Toll Free: 888.733.3456 ǁ 303.539.8300 ǁ Fax: 303.539.8399
www.koalabear.com
P/N 496 Januar 2011
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.