Knoll Systems HDP2350b User Manual

Installation and user manual v1.0

HDP2350

Copyright

Ver.: 01

This publication, including all photographs, illustrations and software, is protected under international
copyright laws, with all rights reserved. Neither this manual, nor any of the material contained herein, may
be reproduced without written consent of the author.

© Copyright 2015

Disclaimer

The information in this document is subject to change without notice. The manufacturer makes no
representations or warranties with respect to the contents hereof and specifically disclaims any implied
warranties of merchantability or fitness for any particular purpose. The manufacturer reserves the right to
revise this publication and to make changes from time to time in the content hereof without obligation of
the manufacturer to notify any person of such revision or changes.

Trademark Recognition

Kensington is a U.S. registered trademark of ACCO Brand Corporation with issued registrations
and pending applications in other countries throughout the world.

HDMI, the HDMI Logo, and High-Definition Multimedia Interface are trademarks or
registered trademarks of HDMI Licensing LLC in the United States and other countries.

All other product names used in this manual are the properties of their respective owners and are
acknowledged.

— i —

Important Safety Information

Important:

It is strongly recommended that you read this section carefully before using the projector. These
safety and usage instructions will ensure that you enjoy many years of safe use of the projector.

Keep this manual for future reference.

Symbols Used

Warning symbols are used on the unit and in this manual to alert you of hazardous situations.
The following styles are used in this manual to alert you to important information.

Note:

Provides additional information on the topic at hand.

Important:

Provides additional information that should not be overlooked.

Caution:

Alerts you to situations that may damage the unit.

Warning:

Alerts you to situations that may damage the unit, create a hazardous environment, or cause
personal injury.

Throughout this manual, component parts and items in the OSD menus are denoted in bold font as in this
example:
“Push the Menu button on the remote control to open the Main menu.”

General Safety Information

 Do not open the unit case. Aside from the projection lamp, there are no user-serviceable parts in

the unit. For servicing, contact qualified service personnel.

 Follow all warnings and cautions in this manual and on the unit case.
 The projection lamp is extremely bright by design. To avoid damage to eyes, do not look into the

lens when the lamp is on.

 Do not place the unit on an unstable surface, cart, or stand.
 Avoid using the system near water, in direct sunlight, or near a heating device.
 Do not place heavy objects such as books or bags on the unit.

— ii —

Projector Installation Notice

15

°

-15°

Mininum 500mm
(19.69 inch)

Mininum 500mm
(19.69 inch)

Mininum 500mm
(19.69 inch)

Mininum 500mm
(19.69 inch)

Mininum 100mm
(3.94 inch)

Mininum 300mm
(11.81 inch)

 Place the projector in a horizontal position

The tilt angle of the projector should not exceed 15 degrees, nor should the projector be
installed in any way other than the desktop and ceiling mount, otherwise lamp life could decrease
dramatically, and may lead to other unpredictable damages.

 Allow at least 50 cm clearance around the exhaust vent.

Preface



 Ensure that the intake vents do not recycle hot air from the exhaust vent.
 When operating the projector in an enclosed space, ensure that the surrounding air temperature

within the enclosure does not exceed operation temperature while the projector is running, and the
air intake and exhaust vents are unobstructed.

 All enclosures should pass a certified thermal evaluation to ensure that the projector does not

recycle exhaust air, as this may cause the device to shutdown even if the enclosure temperature is
with the acceptable operation temperature range.

– iii –

Verify Installation Location

 To supply power, the 3-blade (with earthing lead) socket should be used to ensure proper

grounding and equalized ground potential for all of the equipment in the Projector System.

 The power code provided with the Projector should be used. In case of any missing item, other

qualified 3-blade (with earthing lead) power cord can be used as substitution; however, do not use
2-blade power cord.

 Verify if the voltage is stable, grounded properly and there is no electricity leakage.
 Measure total power consumption which should not higher the safety capacity and avoid safety

issue and short circuit.

 Turn on Altitude Mode when located in high altitude areas
 When installation the bracket, make sure the weight limit is not exceed and firmly secured.
 Avoid installing near air conditioner duct or subwoofer.
 Avoid installing at high temperature, insufficient cooling and heavy dust locations.
 Keep your product away from fluorescent lamps (> 1 meter) to avoid malfunction

caused by IR interference

 The VGA IN connector should be connected to the VGA IN port. Note that it should be inserted

tightly, with the screws on both sides securely fastened to ensure proper connection of the signal
wire for achieving optimal display effect.

 The AUDIO IN connector should be connected to the AUDIO IN port and CANNOT be connected

to AUDIO OUT or other ports like BNC, RCA; otherwise, it will lead to mute output and even
DAMAGE the port.

 Install the projector above 200cm to avoid damage.
 The power cord and signal cable should be connected before power on the projector. During the

projector starting and operating process, DO NOT insert or remove the signal cable or the power
cord to avoid damaging the projector.

Cooling notes

Air outlet

 Make sure the air outlet is 50cm clear of any obstruction to ensure proper cooling.
 Air outlet location should not be in front of the lens of other projector to avoid causing illusions.
 Keep the outlet at least 100cm away from the inlets of other projectors

 The projector generates a massive amount of heat during use. The internal fan dissipates the heat

of the projector when shutting down, and such process may continue for a certain period. After the
project enters STANDBY MODE status, press the AC power button to turn off the projector and
remove the power cord. DO NOT remove the power cord during the shutdown process, as it may
cause damage to the projector. In the meantime, the delayed heat radiating will also affect the
service life of the projector. The shutdown process may vary depending on the model used.
Whatever the case may be, be sure to disconnect the power cord till after the projector enters the
STANDBY status.

Air inlet

 Make sure there is no object blocking air input within 30 cm.
 Keep the inlet away from other heat sources
 Avoided heavy dust area

— iv —

Preface

DISPOSAL: Do not use household or municipal waste collection services for
disposal of electrical and electronic equipment. EU countries require the use
of separate recycling collection services.

Power Safety

 Only use the supplied power cord.
 Do not place anything on the power cord. Place the power cord where it will not be in the way of

foot traffic.

 Remove the batteries from the remote control when storing or not in use for a prolonged period.

Replacing the Lamp

Replacing the lamp can be hazardous if done incorrectly. See Replacing the Projection Lamp on page 53
for clear and safe instructions for this procedure. Before replacing the lamp:

 Unplug the power cord.
 Allow the lamp to cool for about one hour.

Caution:

In rare cases the lamp bulb may burn out during normal operation and cause glass dust or shards
to be discharged outward from the rear exhaust vent.

Do not inhale or do not touch glass dust or shards. Doing so could result in injury.
Always keep your face away from the exhaust vent so that you do not suffer from the gas and

broken shards of the lamp.

Cleaning the Projector

 Unplug the power cord before cleaning. See Cleaning the Projector on page 59.
 Allow the lamp to cool for about one hour.

Regulatory Warnings

Before installing and using the projector, read the regulatory notices in the Regulatory Compliance on
page 72.

Important Recycle Instructions:

Lamp(s) inside this product contain mercury. This product may contain other electronic waste that
can be hazardous if not disposed of properly. Recycle or dispose in accordance with local, state, or federal
Laws. For more information, contact the Electronic Industries Alliance at WWW.EIAE.ORG. For lamp

specific disposal information check WWW.LAMPRECYCLE.ORG.

Symbol Explanations

– v –

Main Features

 Lightweight unit, easy to pack away and transport.
 Compatible with all major video standards including NTSC, PAL, and SECAM.
 A high brightness rating allows for presentations in daylight or in lit rooms.
 Supports resolutions up to WUXGA at 16.7 million colors to deliver crisp, clear images.
 Flexible setup allows for front, rear projections.
 Line-of-vision projections remain square, with advanced keystone correction for angled

projections.

 Input source automatically detected.

About this Manual

This manual is intended for end users and describes how to install and operate the DLP projector.
Wherever possible, relevant information—such as an illustration and its description—has been kept on
one page. This printer-friendly format is both for your convenience and to help save paper, thereby
protecting the environment. It is suggested that you only print sections that are relevant to your needs.

— vi —

Preface

Table of Contents

GETTING STARTED ........................................................................................................................................................... 1

PACKING CHECKLIST ........................................................................................................................................................... 1

VIEWS OF PROJECTOR PARTS ............................................................................................................................................... 2

Front-right View ............................................................................................................................................................ 2

Top view—On-screen Display (OSD) buttons and LEDs ....................................................................................... 3

Rear view ....................................................................................................................................................................... 4

Bottom view ................................................................................................................................................................... 6

REMOTE CONTROL PARTS ................................................................................................................................................... 7

REMOTE CONTROL OPERATING RANGE ............................................................................................................................... 9

PROJECTOR AND REMOTE CONTROL BUTTONS .................................................................................................................... 9

SETUP AND OPERATION ............................................................................................................................................... 10

INSERTING THE REMOTE CONTROL BATTERIES ................................................................................................................. 10

INSTALLING OR REMOVING THE OPTIONAL LENS .............................................................................................................. 11

Removing the Existing Lens From the Projector ................................................................................................... 11

Installing the New Lens ............................................................................................................................................. 12

STARTING AND SHUTTING DOWN THE PROJECTOR ............................................................................................................. 13

SETTING AN ACCESS PASSWORD (SECURITY LOCK) .......................................................................................................... 15

ADJUSTING THE PROJECTOR LEVEL ................................................................................................................................... 17

ADJUSTING PROJECTED IMAGE POSITION USING SHIFT ..................................................................................................... 18

Adjusting the vertical image position ....................................................................................................................... 18

Adjusting the horizontal image position .................................................................................................................. 19

Shift Range Diagram ................................................................................................................................................. 19

ADJUSTING THE ZOOM, FOCUS AND KEYSTONE ................................................................................................................ 20

ADJUSTING THE VOLUME .................................................................................................................................................. 21

ON-SCREEN DISPLAY (OSD) MENU SETTINGS ...................................................................................................... 22

OSD MENU CONTROLS ..................................................................................................................................................... 22

Navigating the OSD ................................................................................................................................................... 22

SETTING THE OSD LANGUAGE .......................................................................................................................................... 23

OSD MENU OVERVIEW ..................................................................................................................................................... 24

IMAGE MENU ..................................................................................................................................................................... 27

Computer Menu .......................................................................................................................................................... 28

Advanced Feature ...................................................................................................................................................... 29

White Balance ............................................................................................................................................................. 30

Color Manager ............................................................................................................................................................ 31

SETTINGS 1 MENU ............................................................................................................................................................. 32

Audio ............................................................................................................................................................................ 33

Advanced 1 Feature ................................................................................................................................................... 34

Advanced 2 Feature ................................................................................................................................................... 36

SETTINGS 2 MENU ............................................................................................................................................................. 37

Status ........................................................................................................................................................................... 38

Advanced 1 Feature ................................................................................................................................................... 39

Advanced 2 Feature ................................................................................................................................................... 51

MAINTENANCE AND SECURITY .................................................................................................................................. 53

REPLACING THE PROJECTION LAMP ................................................................................................................................... 53

Resetting the Lamp .................................................................................................................................................... 56

CLEANING THE FILTER (FILTER: OPTIONAL PARTS) ............................................................................................................ 57

REPLACING THE FILTER ..................................................................................................................................................... 58

CLEANING THE PROJECTOR................................................................................................................................................ 59

Cleaning the Lens ...................................................................................................................................................... 59

Cleaning the Case ...................................................................................................................................................... 59

USING THE PHYSICAL LOCK .............................................................................................................................................. 60

Using the Kensington Lock ....................................................................................................................................... 60

Using the Security Chain Lock ................................................................................................................................. 60

TROUBLESHOOTING ...................................................................................................................................................... 61

– vii –

COMMON PROBLEMS AND SOLUTIONS ............................................................................................................................... 61

TIPS FOR TROUBLESHOOTING ............................................................................................................................................ 61

LED ERROR MESSAGES ..................................................................................................................................................... 62

IMAGE PROBLEMS .............................................................................................................................................................. 62

LAMP PROBLEMS ............................................................................................................................................................... 63

REMOTE CONTROL PROBLEMS .......................................................................................................................................... 63

AUDIO PROBLEMS ............................................................................................................................................................. 64

HAVING THE PROJECTOR SERVICED .................................................................................................................................. 64

HDMI Q & A .................................................................................................................................................................... 65

SPECIFICATIONS ............................................................................................................................................................. 66

SPECIFICATIONS ................................................................................................................................................................. 66

PROJECTION DISTANCE VS. PROJECTION SIZE (1080P) ...................................................................................................... 67

Projection Distance and Size Table ......................................................................................................................... 67

TIMING MODE TABLE ........................................................................................................................................................ 69

PROJECTOR DIMENSIONS ................................................................................................................................................... 71

REGULATORY COMPLIANCE ....................................................................................................................................... 72

FCC WARNING .................................................................................................................................................................. 72

CANADA ............................................................................................................................................................................ 72

SAFETY CERTIFICATIONS ................................................................................................................................................... 72

APPENDIX I ........................................................................................................................................................................ 73

RS-232C PROTOCOL.......................................................................................................................................................... 73

— viii —

DLP Projector – User’s Manual

PROJECTOR

R

(W

)

CD-ROM

(T

)

W

Q

D

(O

)

GETTING STARTED

Packing Checklist

Carefully unpack the projector and check that the following items are included:

EMOTE CONTROL

ITH TWO AA BATTERIES

HIS USER’S MANUAL

POWER CORD (1.8M) HDMI CABLE

ARRANTY CARD

UICK START CARD

UST FILTER

PTIONAL

Contact your dealer immediately if any items are missing, appear damaged, or if the unit does not
work. It is recommend that you keep the original packing material should you ever need to return the
equipment for warranty service.

Caution:

Avoid using the projector in dusty environments.

— 1 —

Views of Projector Parts

5

7

Front-right View

ITEM LABEL DESCRIPTION SEE PAGE:

1.

2.

3.

4.

5.

6.

7.

Screw For ensure the lens position

Vertical lens shift Adjusts the image position vertically

Lens release button

Horizontal lens shift Adjusts the image position horizontally

IR receiver Receives IR signal from remote control

Lens Projection Lens

Focus ring Focuses the projected image

Press the release button before removing the
lens

18

11

19

7

20

8.

9.

10.

11.

Ventilation openings on the projector allow for good air circulation, which keeps the projector lamp
cool. Do not obstruct any of the ventilation openings.

Zoom ring Enlarges the projected image

Height adjuster Adjusts level of projector

Function keys

Lamp cover Removes cover to replace lamp module

Important:

See Top view—On-screen Display (OSD)
buttons and LEDs.

17

3

53

Note:

Suggest to loosen the screw before lens shift adjustment and tighten up after finished
adjustment.

— 2 —

Top view—On-screen Display (OSD) buttons and LEDs

ITEM

LABEL

DESCRIPTION

SEE

PAGE:

1.

MENU

Opens and exits OSD menus

22

2.

Navigates and changes settings in the OSD
Quick Menu – For Keystone

3.

ENTER

Enter or confirm highlighted OSD menu item

4.

BLANK

Displays a blank screen and mutes audio

5.

Navigates and changes settings in the OSD
Quick Menu – For Volume -

22

6.

AUTO

Optimizes image size, position, and resolution

7.

Navigates and changes settings in the OSD
Quick Menu – For Volume +

22

8.

Navigates and changes settings in the OSD
Quick Menu – For Keystone

9.

SOURCE

Enter the Source menu

– 3 –

Rear view

121314

16

7
8

30

1 2 3

4

5 6 7 8 9 10 11

26272829

25

23

21

15

1
1

19

ITEM LABEL DESCRIPTION SEE PAGE:

1.

2.

VGA1 Connect a RGB cable from a computer or a video enabled device.

AUDIO IN 1 Connect the AUDIO cable from an input device.

3.

4.

5.

6.

7.

8.

9.

10.

11.

12.

VGA2 Connect a RGB cable from a computer or a video enabled device.

AUDIO IN 2

POWER

PWR LED

TEMP LED Red Over temperature

READY LED

HDMI Connect the HDMI cable from a HDMI device.

DVI-D Connect the DVI cable from a computer.

3D SYNC OUT
(5V)

DISPLAYPORT Connect a DISPLAYPORT cable to a DISPLAYPORT source.

Connect the AUDIO cable from an input device.
Note: Share with DVI audio input.

Turns the projector on or off (main power switch must
be turned on first). Press to place the projector in
standby mode.

Red Standby, Over Temperature

Blue Lamp Lit , System stable

Flashing

Red Lamp Lit , System stable, Lamp Fail

Flashing Error code (See as LED indicator table)

Connect 3D IR glasses receiver unit.

Power on, Cooling, Error code (See as
LED indicator table)

13

62

13.

14.

USB CHARGE
(1.5A)

RJ-45 Connect a LAN cable from Ethernet.

For USB charge.

— 4 —

ITEM

LABEL

DESCRIPTION

SEE PAGE:

15.

VGA OUT

Connect the RGB cable to a display.
(Pass through by VGA1 only)

16.

AUDIO OUT

Connect an AUDIO cable for audio loop through.

17.

IR receiver

Receive IR signal from remote control.

7

18.

SERVICE

For service use.

19.

RS-232

Connects RS-232 serial port cable for remote control.

20.

12V OUT

When connected to the screen through a commercially available cable,
the screen deploys automatically on start up of the projector. The screen
retracts when the projector is powered off (see notes below).

21.

WIRED REMOTE

Wire remote control connector (connect with wire remote connector of the
Remote Control set).

22.

AUDIO IN 3 L/R
RCA (YPbPr)

Connect the audio cables from a audio device.

23.

AUDIO IN 4 L/R
RCA (Video/ S­Video)

Connect the audio cables from a audio device.

24.

VIDEO

Connect the composite cable from a video device.

25.

S-VIDEO

Connect the S-video cable from a video device.

26.

YPbPr

Connect a component video enabled device.

27.

AC IN

Connects the power cable.

13

28.

Power switch

Turns on/off the projector.

29.

Security chain
lock

Helps protect the projector from unauthorized use.

60

30.

Kensington Lock

Secures to permanent object with a Kensington Lock
system.

Note:



To use this feature, you must plug in the connector before turn on/off the projector.



Screen controllers are supplied and supported by screen manufacturers.



Do not use this jack for anything other than intended use.

Warning:

As a safety precaution, disconnect all power to the projector and connecting devices before making
connections.

– 5 –

Bottom view

ITEM

LABEL

DESCRIPTION

SEE PAGE:

1.

Tilt adjustor

Rotate adjuster lever to adjust angle position.

17

2.

Ceiling support holes

Contact your dealer for information on mounting the projector on a
ceiling

Note:
When installing, ensure that you use only UL Listed ceiling mounts.
For ceiling installations, use approved mounting hardware and M4 screws with a maximum screw
depth of 12 mm (0.47 inch).
The construction of the ceiling mount must be of a suitable shape and strength. The ceiling mount
load capacity must exceed the weight of the installed equipment, and as an additional precaution
be capable of withstanding three times the weight of the equipment (not less than 5.15 kg) over a
period of 60 seconds.

— 6 —

Remote Control Parts

Important:

1. Avoid using the projector with bright fluorescent lighting turned on. Certain high-frequency

fluorescent lights can disrupt remote control operation.

2. Be sure nothing obstructs the path between the remote control and the projector. If the path
between the remote control and the projector is obstructed, you can bounce the signal off certain
reflective surfaces such as projector screens.

3. The buttons and keys on the projector have the same functions as the corresponding buttons on
the remote control. This user’s manual describes the functions based on the remote control.

– 7 –

ITEM

LABEL

DESCRIPTION

SEE PAGE:

1.

Power OFF

Turns the projector off

13

2.

DVI

Displays the DVI source selection

3.

VGA

Displays the VGA source selection

4.

DP

Displays the DisplayPort source selection

5.

Up cursor /
Keystone+

Navigates and changes settings in the OSD
Quick Menu – For Keystone

22

6.

ENTER

Enters and confirms settings in the OSD

7.

Right cursor

Navigates and changes settings in the OSD

8.

Down cursor /
Keystone-

Navigates and changes settings in the OSD
Quick Menu – For Keystone

9.

3D

Activate 3D video (not available in D5180HD series)

10.

PICTURE MODE

Changes the Display Mode setting

11.

SOURCE

Alternate input source

22

12.

CONTRAST

Displays the contrast settings bar

13.

BRIGHT

Displays the brightness setting bar

14.

SHARP

Displays the sharpness setting bar

15.

COLOR

Displays the color setting bar

16.

FREEZE

Freezes/unfreezes the on-screen picture

17.

VOL +

Adjusts volume

22

18.

AUTO

Auto adjustment for frequency, phase, and position

19.

VOL -

Adjusts volume

20.

BLANK

Makes the screen blank

21.

TINT

Displays the tint setting bar

22.

MUTE

Mutes the built-in speaker

23.

STATUS

Opens the OSD Status menu (the menu only opens when an input
device is detected)

24.

ASPECT RATIO

Displays the ASPECT RATIO selections

25.

MENU

Opens or closed the OSD

22

26.

Left cursor

Navigates and changes settings in the OSD

22

27.

COMP

Displays the Component source selection

28.

VIDEO

Displays the VIDEO source selection

29.

HDMI 1

Displays the HDMI 1 source selection

30.

Power ON

Turns the projector on

13

31.

Status LED

Lights when the remote control is used

32.

IR transmitter

Transmits signals to projector

33.

Wired remote
connector

Wired remote function used

— 8 —

Remote Control Operating Range

The remote control uses infrared transmission to control the projector. It is not necessary to point the
remote directly at the projector. Provided you are not holding the remote perpendicular to the sides or
the rear of the projector, the remote will function well within a radius of about 7 meters (23 feet) and
15 degrees above or below the projector level. If the projector does not respond to the remote control,
move a little closer.

Projector and Remote Control Buttons

The projector can be operated using the remote control or the buttons on the top of the projector. All
operations can be carried out with the remote control; however, the buttons on the projector are
limited in use.

– 9 –

Inserting the Remote Control Batteries

1.

Remove the battery compartment
cover by sliding the cover in the
direction of the arrow.

2.

Insert the battery with the positive
side facing up.

3.

Replace the cover.

SETUP AND OPERATION

Caution:

1. Only use AA batteries (Alkaline batteries are recommended).

2. Dispose of used batteries according to local ordinance regulations.

3. Remove the batteries when not using the projector for prolonged periods.

— 10 —

Installing or Removing the Optional Lens

1.

Pull and release the top cover to
open as shown.

2.

Push the LENSE RELEASE button
to the unlock position.

3.

Grasp the lens.

4.

Rotate the lens counterclockwise.
The existing lens will be
disengaged.

5.

Pull out the existing lens slowly.

Caution:



Do not shake or place excessive pressure on the projector or the lens components as the

projector and lens components contain precision parts.



Before removing or installing the lens, be sure to turn off the projector, wait until the cooling fans

stop, and turn off the main power switch.



Do not touch the lens surface when removing or installing the lens.



Keep fingerprints, dust or oil off the lens surface.



Do not scratch the lens surface.



Work on a level surface with a soft cloth under it to avoid scratching.



If you remove and store the lens, attach the lens cap to the projector to keep off dust and dirt.

Removing the Existing Lens From the Projector

– 11 –

Installing the New Lens

1.

Align the notches and correctly
position the electrical contact pad as
shown in the picture.

Note:

Pin of Electrical contact pins should
be in the direction as shown in the
picture.

2.

Rotate the lens clockwise until you
feel it click into place.

Electrical contact pins

— 12 —

Starting and Shutting down the Projector

Remove the lens cap.

1.

Securely connect the power cord

2.

and signal cable. When connected,
the power led will turn red.

Turn on the lamp by pressing

3.

“ ” button on the rear of the

projector or “ ” on the remote

control.
The PWR LED will now flash red.
The startup screen will display in
approximately 30 seconds. The first
time you use the projector, you can
select your preferred language from
quick menu after the startup screen
display.

– 13 –

4.

If more than one input device is
connected, press the SOURCE

button and use ▲▼ to scroll among

devices.

 DVI: Digital Visual Interface
 HDMI: High-Definition Multimedia Interface

compatible

 DisplayPort: Digital display interface
 VGA 1 / 2: Analog RGB 1 / 2
 Component Video: DVD input YCbCr / YPbPr , or

HDTV input YPbPr

 S-Video: Super video (Y/C separated)

 Composite Video: Traditional composite video

5.

When the “Power Off? /Press

Power again” message appears,
press the POWER button. The
projector turns off.

Caution:

1. Be sure to remove the lens cap before starting projector.

2. Do not unplug the power cord until the READY LED stops flashing–indicating the projector has
cooled down.

— 14 —

Setting an Access Password (Security Lock)

1.

Press the MENU button to open the
OSD menu.

2.

Press the cursor ◄► button to move to

the Settings 1 menu, press the cursor

▲▼ button to select Advanced 1.

3.

Press (Enter) / ► to enter the
Advanced 1 sub menu. Press the

cursor ▲▼ button to select Security
Lock.

4.

Press the cursor ◄► button to enter
and enable or disable security lock
function.

A password dialog box automatically
appears.

You can use the four (arrow) buttons to set a password and prevent unauthorized use of the projector.
When enabled, the password must be entered after you power on the projector. (See Navigating the

OSD on page 22 and Setting the OSD Language on page 23 for help on using OSD menus.)

Important:

Keep the password in a safe place. Without the password, you will not be able to use the projector.
If you lose the password, contact your reseller for information on clearing the password.

– 15 –

5.

You can use the cursor buttons
▲▼◄►
either on keypad or IR remote control
for password entry. You can use any
combination including the same arrow
five times, but not less than five.

Press the cursor buttons in any order to
set the password. Push the MENU
button to exit the dialog box.

6.

The password confirm menu appears
when user presses the power-on key in
case the Security Lock is enabled.
Enter the password in the order you set
it at step 5. In case you forget the
password, please contact the service
center.
The service center will validate the
owner and help reset the password.

— 16 —

Adjusting the Projector Level

1.

To raise the level of the projector,
twist the adjusters counter
clockwise.

2.

To lower the level of the projector,
lift the projector and twist the
adjusters clockwise.

Take note of the following when setting up the projector:

 The projector table or stand should be level and sturdy.
 Position the projector so that it is perpendicular to the screen.
 Remove the Back Foot Holder on the rear adjuster foot before adjusting the projection

angle.

 Ensure the cables are in a safe location. You could trip over them.

– 17 –

Adjusting Projected Image Position Using Shift

Screen

Distance

(L)

Hx10%

100%

Screen Height

(H)

+60%

-20%

0%

20%xH

60%xH

Note:

Suggest to loosen the screw before lens
shift adjustment and tighten up after
finished adjustment.

The Shift feature provides a lens shift function that can be used to adjust the position of the projected
image either horizontally or vertically within the range detailed below.

Shift is a unique system that provides lens shift while maintaining a much higher ANSI contrast ratio
than traditional lens shift systems.

Adjusting the vertical image position

The vertical image height can be adjusted between 60% and -20% ( 1080P) of offset position. Note
that the maximum vertical image height adjustment can be limited by the horizontal image position.
For example it is not possible to achieve the maximum vertical image position height detailed above if
the horizontal image position is at maximum. Please consult the Shift Range diagram below for
further clarification.

— 18 —

Adjusting the horizontal image position

When W and H at 0% offset position
The max. H up shift=Hx60%
The max. H down shift=Hx20%
The max. W shift=Wx5%
When max. W shift is Wx5%

max. H shift=Hx55%

When max. H shift is Hx60%

max. W shift=Hx0%

Wx5% Wx5%

With the lens in the center position the horizontal image position can be adjusted to the left or right by
up to a maximum of 5% of the image width. Note that the maximum horizontal image height
adjustment can be limited by the vertical image position. For example it is not possible to achieve the
maximum horizontal image position if the vertical image position is at maximum. Please consult the
Shift Range diagram below for further clarification.

Shift Range Diagram

– 19 –

Adjusting the Zoom, Focus and Keystone

1.

Use the Image-zoom
control (on the projector
only) to resize the
projected image and
screen size.

2.

Use the Image-focus
control (on the projector
only) to sharpen the
projected image.

3.

Use the KEYSTONE
buttons (on the
projector or the remote
control) to correct
image-trapezoid (wider
top or bottom)
effect.

Remote control and OSD panel

4.

The keystone control
appears on the display.

— 20 —

Adjusting the Volume

1.

Press the Volume +/-
buttons on the remote
control.
The volume control
appears on the display.

2.

Press the Left or Right
Cursor buttons on the

keypad to adjust

Volume +/-.

3.

Press the MUTE button
to turn off the volume
(This feature is
available only on the
remote).

– 21 –

ON-SCREEN DISPLAY (OSD) MENU SETTINGS

1. To enter the OSD, press the MENU button.

2. There are three menus. Press the cursor
◄► button to move through the menus.

3. Press the cursor ▲▼ button to move up
and don in a menu.

4. Press ◄► to change values for settings.

5. Press MENU to close the OSD or leave a
submenu.

13

16

5

2

7

2

4

1

1
3

4

5

6

7

OSD Menu Controls

The projector has an OSD that lets you make image adjustments and change various settings.

Navigating the OSD

You can use the remote control cursor buttons or the buttons on the top of the projector to navigate
and make changes to the OSD. The following illustration shows the corresponding buttons on the
projector.

Note:

Depending on the video source, not all items in the OSD are available. For example, the
Horizontal/Vertical Position items in the Computer menu can only be modified when connected
to a PC. Items that are not available cannot be accessed and are grayed out.

— 22 —

Setting the OSD Language

Set the OSD language to your preference before continuing.

1. Press the MENU button. Press the cursor ◄► button to navigate to Settings 1. Press the
cursor ▲▼ button to move to the Advanced 1 menu.

2. Press (Enter) / ► to enter the Advanced 1 sub menu. Press the cursor ▲▼ button
until Language is highlighted.

3. Press the cursor button until the language you want is highlighted.

4. Press the MENU button four times to close the OSD.

– 23 –

OSD Menu Overview

Main
Menu

Sub Menu

Settings

Image

Display Mode

Presentation, Bright, Game,
Movie, TV, sRGB, Blackboard,
User1, User2, ISF_Day,
ISF_Night

Brightness

0~100

Contrast

0~100

Computer

Horizontal Position

-5~5 (depend on Autolock)

Vertical Position

-5~5 (depend on Autolock)

Frequency

0~31

Tracking

-5~5

Auto Sync

On, Off

Auto Image

Advanced

Brilliant Color

1~10

Sharpness

0~31

Gamma

1.8, 2.0, 2.2, 2.4, B&W, Linear

Color Temperature

Warm, Normal, Cold

Video AGC

Off, On

Video Saturation

0~100

Video Tint

0~100

White Balance

RGain

0~200

GGain

0~200

BGain

0~200

ROffset

-256~255

GOffset

-256~255

BOffset

-256~255

Color Manager

Red

Hue, Saturation, Gain

0~100

Green

Hue, Saturation, Gain

0~100

Blue

Hue, Saturation, Gain

0~100

Cyan

Hue, Saturation, Gain

0~100

Magenta

Hue, Saturation, Gain

0~100

Yellow

Hue, Saturation, Gain

0~100

White

Red, Green, Blue

0~100

Use the following illustration to quickly find a setting or determine the range for a setting.

— 24 —

Main
Menu

Sub Menu

Settings

Settings 1

Source

Source

reference Input Source Select (IR/Keypad)

Projection

Normal, Real, Ceiling, Real+Ceiling

Aspect Ratio

Fill, 4:3, 16:9, Letter Box, Native,
Theater Zoom

Keystone

-40~40

Digital Zoom

-10~10

Audio

Volume

0~10

Mute

Off, On

Advanced 1

Language

English, Français, Deutsch, Español,
Português, 簡体中文, 繁體中文, Italiano,

Norsk, Svenska, Nederlands, Русский,
Polski, Suomi, Ελληνικά, 한국어, Magyar,
Čeština, , Türkçe, Việt, 日本語, ไทย ,

, תירבע

Security Lock

Off, On

Blank Screen

Blank, Red, Green, Blue, White

Splash Logo

On, Off

Closed Captioning

Off, On

KeypadLock

Off, On

3D Setting

3D

Off, DLP-Link, IR

3D Sync Invert

Off, On

3D Format

Frame Sequential, Top/Bottom, Side-By­Side, Frame Packing (3D Frame Packing
HDMI source only)

Advanced 2

Test Pattern

None, RGB Ramp, Color Bar, Step Bars,
Checkboard, Grid, Horizontal Lines

H Image Shift

-50~50

V Image Shift

-50~50

– 25 –

Main
Menu

Sub Menu

Settings

Settings 2

Auto Source

Off, On

No Signal
Power Off

0~180

Auto Power
On

Off, On
Lamp Mode

ECO, Normal, Dynamic Eco

Reset All

Status

Active Source

Video Information

Lamp Hours(ECO, Normal)

Software Version

Serial Number

Advanced 1

Menu Position

Center, Down, Up, Left, Right

Translucent Menu

0%, 25%, 50%, 75%, 100%

Low Power Mode

Off, Low Power , On by LAN,
VGA Out

Fan Speed

Normal, High

Lamp Hour Reset

Projector ID

0-98

Network

Network State

Connect, Disconnect

DHCP

On, Off

IP Address

0~255, 0~255, 0~255. 0~255

Subnet Mask

0~255, 0~255, 0~255. 0~255

Gateway

0~255, 0~255, 0~255. 0~255

DNS

0~255, 0~255, 0~255. 0~255

Apply

Ok / Cancel

ISF Mode

Off, Lock, Unlock

Advanced 2

Sleep Timer

0~600

Source Filter

DVI

Disable, Enable

HDMI

Disable, Enable

Display Port

Disable, Enable

VGA1

Disable, Enable

VGA2

Disable, Enable

Component Video

Disable, Enable

S-Video

Disable, Enable

Composite Video

Disable, Enable

Wall Color

Off, Light Yellow, Pink, Light
Green, Blue, blackboard

Color Space

Auto, RGB, YUV

Quantization Range

Auto, Full, limit

Screen Display

16:9 Native, 2.35 Ana, Fixed
Ana, Native

— 26 —

Image Menu

ITEM

DESCRIPTION

Display Mode

Press the cursor ◄► button to enter and set the Display Mode.

Brightness

Press the cursor ◄► button to enter and adjust the display brightness.

Contrast

Press the cursor ◄► button to enter and adjust the display contrast.

Computer

Press (Enter) / ► to enter the Computer menu. See Computer Menu on page 28.

Auto Image

Press (Enter) / ► to automatically adjustment for phase, tracking, size and
position.

Advanced

Press (Enter) / ► to enter the Advanced menu. See Advanced Feature on page

29.

Color Manager

Press (Enter) / ► to enter the color manager menu. See page 31 for more
information on Color Manager.

Attention !

All of display mode parameters when changed will be saved to user mode.

Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the Image
Menu. Press the cursor ▲▼ button to move up and down in the Image menu. Press ◄► to enter

and change values for settings.

– 27 –

Computer Menu

ITEM

DESCRIPTION

Horizontal Position

Press the cursor ◄► button to enter and adjust the display position to left or right.

Vertical Position

Press the cursor ◄► button to enter and adjust the display position to up or down.

Frequency

Press the cursor ◄► button to enter and adjust the A/D sampling clock.

Tracking

Press the cursor ◄► button to enter and adjust the A/D sampling dot.

Auto Sync

Press the cursor ◄► button to enter and enable or disable the autolock control for
RGB source.

Press the MENU button to open the OSD menu. Press ◄► to move to the Image menu. Press ▲▼
to move to the Computer menu and then press Enter or ►. Press ▲▼ to move up and down in the
Computer menu.

— 28 —

Advanced Feature

ITEM

DESCRIPTION

Brilliant Color

Press the cursor ◄► button to enter and adjust the Brilliant Color value.

Sharpness

Press the cursor ◄► button to enter and adjust the display sharpness.

Gamma

Press the cursor ◄► button to enter and adjust the gamma correction of the display.

Color Temperature

Press the cursor ◄► button to enter and adjust the color temperature.

Video AGC

Press the cursor ◄► button to enter and enable or disable the Automatic Gain Control
for video source.

Video Saturation

Press the cursor ◄► button to enter and adjust the video saturation.

Video Tint

Press the cursor ◄► button to enter and adjust the video tint/hue.

White Balance

Press the ENTER / ► button to enter the White Balance sub menu. See White

Balance on page 30.

Press the Menu button to open the OSD menu. Press ◄► to move to the Image menu. Press ▼▲
to move to the Advanced menu and then press Enter or ►. Press ▼▲ to move up and down in the
Advanced menu.

– 29 –

White Balance

ITEM

DESCRIPTION

R Gain

Press the ◄► buttons to adjust the Red Gain.

G Gain

Press the ◄► buttons to adjust the Green Gain.

B Gain

Press the ◄► buttons to adjust the Blue Gain.

R Offset

Press the ◄► buttons to adjust the Red Offset.

G Offset

Press the ◄► buttons to adjust the Green Offset.

B Offset

Press the ◄► buttons to adjust the Blue Offset.

Press the ENTER button to enter the White Balance sub menu.

— 30 —

Color Manager

ITEM

DESCRIPTION

Red

Select to enter the Red Color Manager.
Press the ◄► buttons to adjust the Hue, Saturation, and Gain.

Green

Select to enter the Green Color Manager.
Press the ◄► buttons to adjust the Hue, Saturation, and Gain.

Blue

Select to enter the Blue Color Manager.
Press the ◄► buttons to adjust the Hue, Saturation, and Gain.

Cyan

Select to enter the Cyan Color Manager.
Press the ◄► buttons to adjust the Hue, Saturation, and Gain.

Magenta

Select to enter the Magenta Color Manager.
Press the ◄► buttons to adjust the Hue, Saturation, and Gain.

Yellow

Select to enter the Yellow Color Manager.
Press the◄► buttons to adjust the Hue, Saturation, and Gain.

White

Select to enter the White Color Manager.
Press the ◄► buttons to adjust the Red, Green, and Blue.

Press the Menu button to open the OSD menu. Press ◄► to move to the Image menu. Press ▼▲
to move to the Color Manager menu and then press Enter or ►. Press ▼▲ to move up and down in
the Color Manager menu.

– 31 –

Settings 1 Menu

ITEM

DESCRIPTION

Source

Press (Enter) / ► to enter the Source menu. Reference input Source select
(IR / Keypad).

Projection

Press the cursor ◄► button to enter and choose from four projection methods:

Aspect Ratio

Press the cursor ◄► button to enter and adjust the video aspect ratio.

Keystone

Press the cursor ◄► button to enter and adjust the display keystone.

Digital Zoom

Press the cursor ◄► button to enter and adjust the Digital Zoom menu.

Audio

Press (Enter) / ► to enter the Audio menu. See Audio on page 33.

Advanced 1

Press (Enter) / ► to enter the Advanced 1 menu. See Advanced 1 Feature on
page 34.

Advanced 2

Press (Enter) / ► to enter the Advanced 2 menu. See Advanced 2 Feature on
page 36.

Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the Settings
1 menu. Press the cursor ▲▼ button to move up and down in the Settings 1 menu. Press ◄► to
enter and change values for settings.

— 32 —

Audio

ITEM

DESCRIPTION

Volume

Press the cursor ◄► button to enter and adjust the audio volume.

Mute

Press the cursor ◄► button to enter and turn on or off the speaker.

Press the Menu button to open the OSD menu. Press ◄► to move to the Settings 1 menu. Press

▼▲ to move to the Audio menu and then press Enter or ►. Press ▼▲ to move up and down in the
Audio menu.

– 33 –

Advanced 1 Feature

ITEM

DESCRIPTION

Language

Press the cursor ◄► button to enter and select a different localization Menu.

Security Lock

Press the cursor ◄► button to enter and enable or disable security lock function.

Blank Screen

Press the cursor ◄► button to enter and select different color to blank the screen.

Splash Logo

Press the cursor ◄► button to enter and select splash logo on or off.

Closed Captioning

Press the cursor ◄► button to enter and enable or disable Closed Captioning

Keypad Lock

Press the cursor ◄► button to enter and enable or disable keys can be work on
keypad.

3D Setting

Press (Enter) / ► to enter the 3D menu. See page 35 for more information on 3D

Setting.

Press the Menu button to open the OSD menu. Press ◄► to move to the Settings 1 menu. Press
▲▼ to move to the Advanced 1 menu and then press Enter or ►. Press ▲▼ to move up and down
in the Advanced 1 menu. Press ◄► to enter and change values for setting.

Note:

To enjoy the 3D function, first enable the Play Movie in 3D setting found in your DVD device under the
3D Disc Menu.

— 34 —

3D Setting

ITEM

DESCRIPTION

3D

Press the cursor ◄► button to enter and select different 3D mode.

3D Sync Invert

Press the cursor ◄► button to enter and enable or disable 3D Sync Invert.

3D Format

Press the cursor ◄► button to enter and enable or disable different 3D Format.

Note:

1. The 3D OSD menu item is gray if there is no appropriate 3D source. This is the default setting.

2. When the projector is connected to an appropriate 3D source, the 3D OSD menu item is enabled for
selection.

3. Use 3D glasses to view a 3D image.

4. You need 3D content from a 3D DVD or 3D media file.

5. You need to enable the 3D source (some 3D DVD content may have a 3D on-off selection feature).

6. You need DLP link 3D or IR 3D shutter glasses. With IR 3D shutter glasses, you need to install a
driver on your PC and connect a USB emitter.

7. The 3D mode of the OSD needs to match the type of glasses (DLP link or IR 3D).

8. Power on the glasses. Glasses normally have a power on -off switch.
Each type of glasses has their own configuration instructions. Please follow the configuration
instructions that come with your glasses to finish the setup process.

Note:

Since different types of glass (DLP link or IR shutter glass) have their own setting instructions,

Please follow the guide to finish the setup process.

– 35 –

Advanced 2 Feature

ITEM

DESCRIPTION

Test Pattern

Press the cursor ◄► button to enter and select internal test pattern.

H Image Shift

Press the cursor ◄► button to enter and select H Image Shift.

V Image Shift

Press the cursor ◄► button to enter and select V Image Shift.

Press the Menu button to open the OSD menu. Press ◄► to move to the Settings 1 menu. Press
▲▼ to move to the Advanced 2 menu and then press Enter or ►. Press ▲▼ to move up and down
in the Advanced 2 menu. Press ◄► to enter and change values for setting.

— 36 —

Settings 2 Menu

ITEM

DESCRIPTION

Auto Source

Press the cursor ◄► button to enter and enable or disable automatic source

detection.

No Singal Power
Off (min.)

Press the cursor ◄► button to enter and enable or disable automatic shutdown of
lamp when no signal.

Auto Power On

Press the cursor ◄► button to enter and enable or disable automatic power On when
AC power is supplied.

Lamp Mode

Press the cursor ◄► button to enter and select the lamp mode for higher brightness
or lower brightness to save lamp life.

Reset All

Press (Enter) / ► to reset all settings to default values.

Status

Press (Enter) / ► to enter the Status menu. See page 38 for more information on

Status.

Advanced 1

Press (Enter) / ► to enter the Advanced 1 menu. See Advanced 1 Feature on
page 39.

Advanced 2

Press (Enter) / ► to enter the Advanced 2 menu. See Advanced 2 Feature on
page 51.

Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the Settings
2 menu. Press the cursor ▲▼ button to move up and down in the Settings 2 menu.

Note :
Dynamic ECO: Auto power consumption saving according to your dynamic content (30% Max saving on

blank screen).
Extreme Dimming: Saving 50% lamp power consumption by blank screen (press BLANK button)

– 37 –

Status

ITEM

DESCRIPTION

Active Source

Display the activated source.

Video Information

Displays resolution/video information for RGB source and color standard for Video
source.

Lamp Hours

Lamp hour used information is displayed. (ECO, Normal)

Software Version

Showing system software version.

Serial Number

Showing serial number of this projector.

Press the cursor ▲▼ button to move up and down in the Settings 2 menu. Select the Status menu
and press Enter or ► to enter.

— 38 —

Advanced 1 Feature

ITEM

DESCRIPTION

Menu Position

Press the cursor ◄► button to enter and select different OSD location.

Translucent Menu

Press the cursor ◄► button to enter and select OSD background translucent level.

Low Power Mode

Press the cursor ◄► button to enter and turn Low Power Mode Off, Low Power, On by
LAN or VGA Out.

Fan Speed

Press the cursor ◄► button to enter and toggle between Normal and High fan speeds.
Note: We recommend selecting high speed in high temperatures, high humidity, or
high altitude (higher than 1500m/4921ft) areas.

Lamp Hour Reset

After replacing the lamp, this item should be reset. See page 40 for more information
on Lamp Hour Reset.

Projector ID

Press the cursor ◄► button to enter and adjust a two digit projector ID from 00
through 98.

Network

Press (Enter) / ► to enter the Network menu. See page 40 for more information on

Network.

ISF Mode

Press the cursor ◄► button to enter and adjust ISF parameter.

Press the Menu button to open the OSD menu. Press ◄► to move to the Settings 2 menu. Press
▲▼ to move to the Advanced 1 menu and then press Enter or ►. Press ▲▼ to move up and down
in the Advanced 1 menu. Press ◄► to enter and change values for setting.

Note:
About “On By Lan”, RJ45 will support to be waked up in this mode(Under 6W) but scalar won’t.

– 39 –

Lamp Hour Reset

ITEM

DESCRIPTION

Network State

Displays the network connection status.

DHCP

Press the cursor ◄► button to turn DHCP On or Off.
Note: If you select DHCP Off, complete the IP Address, Subnet Mask, Gateway,
and DNS fields.

IP Address

Enter a valid IP address if DHCP is turned off.

Subnet Mask

Enter a valid Subnet Mask if DHCP is turned off.

Gateway

Enter a valid Gateway address if DHCP is turned off.

DNS

Enter a valid DNS name if DHCP is turned off.

Apply

Press (Enter) / ► to confirm settings.

Please refer to Resetting the Lamp on page 56 to reset the lamp hour counter.

Network

— 40 —

LAN_RJ45

Wired LAN Terminal functionalites

Remote control and monitoring of a projector from a PC (or Laptop) via wired LAN is also possible.
Compatibility with Crestron / AMX (Device Discovery) / Extron control boxes enables not only collective
projector management on a network but also management from a control panel on a PC (or Laptop)
browser screen.

 Crestron is a registered trademark of Crestron Electronics, Inc. of the United States.
 Extron is a registered trademark of Extron Electronics, Inc. of the United States.
 AMX is a registered trademark of AMX LLC of the United States.
 PJLink applied for trademark and logo registration in Japan, the United States of America, and

other countries by JBMIA.

Supported External Devices

This projector is supported by the specified commands of the Crestron Electronics controller and
related software (ex, RoomView ®).

http://www.crestron.com/

This projector is supported by AMX ( Device Discovery ).

http://www.amx.com/

This projector is compliant to support Extron device(s) for reference.

http://www.extron.com/

This projector supports all commands of PJLink Class1 (Version 1.00).

http://pjlink.jbmia.or.jp/english/

For more detail of information about the diverse types of external devices which can be connected to the
LAN/RJ45 port and remote/control the projector, as well as the related control commands supporting for
each external device, kindly please get contact with the Support-Service team directly.

– 41 –

LAN_RJ45

1. Connect an RJ45 cable to RJ45 ports on the projector and the PC (Laptop).

2. On the PC (Laptop), select Start  Control Panel  Network and Internet.

— 42 —

3. Right-click on Local Area Connection, and select Properties.

4. In the Properties window, select the Networking tab, and select Internet Protocol (TCP/IP).

5. Click Properties.

6. Click Use the following IP address and fill in the IP address and Subnet mask, then click OK.

– 43 –

7. Press the Menu button on the projector.

8. Select Settings2 Advanced1  Network

9. After getting into Network, input the following:

 DHCP: Off

 IP Address: 10.10.10.10

 Subnet Mask: 255.255.255.0

 Gateway: 0.0.0.0

 DNS Server: 0.0.0.0

10. Press (Enter) /  to confirm settings.

Open a web browser
(for example, Microsoft Internet Explorer with Adobe Flash Player 9.0 or higher).

11. In the Address bar, input the IP address: 10.10.10.10.

12. Press (Enter) /  .

The projector is setup for remote management. The LAN/RJ45 function displays as follows.

— 44 —

CATEGORY

ITEM

INPUT-LENGTH

Crestron Control
IP Address

15

IP ID

3

Port

5

Projector
Projector Name

10

Location

10

Assigned To

10

Network Configuration

DHCP (Enabled)

(N/A)

IP Address

15

Subnet Mask

15

Default Gateway

15

DNS Server

15

User Password
Enabled

(N/A)

New Password

10

Confirm

10

Admin Password
Enabled

(N/A)

New Password

10

Confirm

10

For more information, please visit http://www.crestron.com.

– 45 –

Preparing Email Alerts

1. Make sure that user can access the homepage of LAN RJ45 function by web browser (for ex­ample, Microsoft Internet Explorer v6.01/v8.0).

2. From the Homepage of LAN/RJ45, click Alert Settings.

3. By default, these input boxes in Alert Settings are blank.

— 46 —

4. For Sending alert mail, input the following:

SMTP field is the mail server for sending out email (SMTP protocol). This is a required field.

To eld is the recipient’s email address (for example, the projector administrator). This is a

required field.

Cc field sends a carbon copy of the alert to the specified email address. This is an optional

field (for example, the projector administrator’s assistant).

From eld is the sender’s email address (for example, the projector administrator). This is

a required field.

Note: Fill in all fields as specified. User can click Send Test Mail to test what setting is correct. For

successful sending an e-mail alert, you must select alert conditions and enter a correct e-mail
address.

– 47 –

RS232 by Telnet Function

Besides projector connected to RS232 interface with “Hyper-Terminal” communication by dedicated
RS232 command control, there is alternative RS232 command control way, so called “RS232 by
TELNET” for LAN/RJ45 interface.

Quick Start-Guide for “RS232 by TELNET”

Check and get the IP-Address on OSD of the projector.
Make sure that laptop/PC can access the web-page of the projector.

Make sure that “Windows Firewall” setting to be disabled in case of “TELNET” function filtering out

by laptop/PC.

Start => All Programs => Accessories => Command Prompt

— 48 —

Input the command format like the below:
telnet ttt.xxx.yyy.zzz 23 (“Enter” key pressed)
(ttt.xxx.yyy.zzz: IP-Address of the projector)
If Telnet-Connection ready, and user can have RS232 command input, then “Enter” key pressed,

the RS232 command will be workable.

How to have TELNET enabled in Windows VISTA / 7

By default installation for Windows VISTA, “TELNET” function is not included. But end-user can
have it by way of “Turn Windows features On or Off” to be enabled.

Open “Control Panel” in Windows VISTA

Open “Programs”

– 49 –

Select “Turn Windows features on or off” to open

Have “Telnet Client” option checked, then press “OK” button.

Specsheet for “RS232 by TELNET” :

1. Telnet: TCP

2. Telnet port: 23
(for more detail, kindly please get contact with the service agent or team)

3. Telnet utility: Windows “TELNET.exe” (console mode)

4. Disconnection for RS232-by-Telnet control normally: Close Windows Telnet utility directly
after TELNET connection ready

5. Limitation 1 for Telnet-Control: there is less than 50 bytes for successive network payload for
Telnet-Control application.

Limitation 2 for Telnet-Control: there is less than 26 bytes for one complete RS232 command
for Telnet-Control.

Limitation 3 for Telnet-Control: Minimum delay for next RS232 command must be more than
200 (ms).

(*, In Windows built-in “TELNET.exe” utility, “Enter” key pressed will have “Carriage-Return”
and “New-Line” code.)

— 50 —

Advanced 2 Feature

ITEM

DESCRIPTION

Sleep Timer (min)

Press the cursor ◄► button to enter and set Sleep timer. The projector automatically
turns off after the preset period of time.

Source Filter

Press (Enter) / ► to enter the Source Filter menu. See page 51 for more
information on Source Filter.

Wall Color

Press the cursor ◄► button to enter and set the Wall Color.

Color Space

Press the cursor ◄► button to enter and set the Color Space.

Quantization
Range

Press the cursor ◄► button to enter and set the Quantization Range.

Screen Display

Press the cursor ◄► button to enter and set the Screen Display.

Press the Menu button to open the OSD menu. Press ◄► to move to the Settings 2 menu. Press
▲▼ to move to the Advanced 2 menu and then press Enter or ►. Press ▲▼ to move up and down
in the Advanced 2 menu. Press ◄► to enter and change values for setting.

– 51 –

Source Filter

ITEM

DESCRIPTION

DVI

Press the ◄► buttons to enter and enable or disable the DVI source.

HDMI

Press the ◄► buttons to enter and enable or disable the HDMI source.

DisplayPort

Press the ◄► buttons to enter and enable or disable the DisplayPort source.

VGA1

Press the ◄► buttons to enter and enable or disable the VGA1 source.

VGA2

Press the ◄► buttons to enter and enable or disable the VGA2 source.

Component Video

Press the ◄► buttons to enter and enable or disable the Component Video source.

S-Video

Press the ◄► buttons to enter and enable or disable the S-Video source.

Composite Video

Press the ◄► buttons to enter and enable or disable the Composite Video source.

Press the ENTER button to enter the Source Filter sub menu.

— 52 —

MAINTENANCE AND SECURITY

Replacing the Projection Lamp

The projection lamp should be replaced when it burns out. It should only be replaced with a certified
replacement part, which you can order from your local dealer.

Important:

a. The projection lamp used in this product contains a small amount of mercury.

b. Do not dispose this product with general household waste.

c. Disposal of this product must be carried out in accordance with the regulations of your local

authority.

Warning:

Be sure to turn off and unplug the projector at least 30 minutes before replacing the lamp. Failure to
do so could result in a severe burn.

Caution:

In rare cases the lamp bulb may burn out during normal operation and cause glass dust or shards
to be discharged outward from the rear exhaust vent.

Do not inhale or do not touch glass dust or shards. Doing so could result in injury.
Always keep your face away from the exhaust vent so that you do not suffer from the gas and

broken shards of the lamp.
When removing the lamp from a ceiling-mounted projector, make sure that no one is under the

projector. Glass fragments could fall if the lamp has been burned out.

IF A LAMP EXPLODES

If a lamp explodes, the gas and broken shards may scatter inside the projector and they may come
out of the exhaust vent. The gas contains toxic mercury.

Open windows and doors for ventilation.
If you inhale the gas or the shards of the broken lamp enter your eyes or mouth, consult the doctor

immediately.

Switch off the power to the

1.

projector by pressing the
POWER button.

Allow the projector to cool

2.

down at least 30 minutes.

Disconnect the power

3.

cord.

– 53 –

4.

Unlock the lamp cover.

5.

Pull up and remove the
cover.

6.

Use a screwdriver to
remove the screws from
the lamp module.

7.

Pull out the lamp module.

— 54 —

8.

Reverse steps 1 to 7 to
install the new lamp
module.
While installing, align the
lamp module with the
connector and ensure it is
level to avoid damage.

Note:
The lamp module must sit
securely in place and the
lamp connector must be
connected properly before
tightening the screws.

– 55 –

Resetting the Lamp

1.

Press the MENU button to open
the OSD menu.

2.

Press the cursor ◄► button to
move to the Settings 2 menu.
Press the cursor button to move
down to Advanced 1 and press
enter.

3.

Press the cursor ▼▲ button to
move down to Lamp Hour Reset.

4.

Press the cursor ► or Enter

button.
A message screen appears.

5.

Press ▼▲◄► buttons to reset
the lamp hour.

6.

Press the MENU button to get
back to Settings 2.

After replacing the lamp, you should reset the lamp hour counter to zero. Refer to the following:

— 56 —

Cleaning the filter (filter: optional parts)

1.

Turn off the projector, and
unplug the AC power cord
from the AC outlet.

2.

Cleaning the filter with a
vacuum cleaner.

The air filter prevents dust from accumulating on the surface of the optical elements inside the
projector. If the filter is dirty or clogged, your projector may overheat or degrading the projected image
quality.

Caution:

Recommend avoiding dusty or smoky environments when you operate the projector, it may cause
poor image quality.

If the filter is heavily clogged and unable to clean, replace a new filter.

Note:

Using a ladder is recommended to access the filter. Do not remove the projector from the wall
mount.

– 57 –

Replacing the Filter

1.

Turn off the projector, and
unplug the AC power cord
from the AC outlet.
Clean up the dust on the
projector and around the
air vents.
Pull out the filter cover and
remove from the projector

2.

Lift the filter from the filter
cover.

3.

Replace a new filter
module or replace filter into
cover.

4.

Replace the filter cover
back to the projector by
pushing gently in the
direction shown.

Warning:

Do not wash the filter with the water or other liquid matter

Important:

When the lamp is replaced, the filter should also be replaced, not cleaned.

— 58 —

Cleaning the Projector

Cleaning the projector to remove dust and grime will help ensure trouble-free operation.

Warning:

1. Be sure to turn off and unplug the projector at least 30 minutes before cleaning. Failure to do so

could result in a severe burn.

2. Use only a dampened cloth when cleaning. Do not allow water to enter the ventilation openings
on the projector.

3. If a little water gets into the projector interior while cleaning, leave unplugged in a well-ventilated
room for several hours before using.

4. If a lot of water gets into the projector interior when cleaning, have the projector serviced.

Cleaning the Lens

You can purchase optic lens cleaner from most camera stores. Refer to the following to clean the
projector lens.

1. Apply a little optic lens cleaner to a clean soft cloth. (Do not apply the cleaner directly to
the lens.)

2. Lightly wipe the lens in a circular motion.

Caution:

1. Do not use abrasive cleaners or solvents.

2. To prevent discoloration or fading, avoid getting cleaner on the projector case.

Cleaning the Case

Refer to the following to clean the projector case.

1. Wipe off dust with a clean dampened cloth.

2. Moisten the cloth with warm water and mild detergent (such as used to wash dishes), and
then wipe the case.

3. Rinse all detergent from the cloth and wipe the projector again.

Caution:

To prevent discoloration or fading of the case, do not use abrasive alcohol-based cleaners.

– 59 –

Using the Physical Lock

Using the Kensington Lock

If you are concerned about security, attach the projector to a permanent object with the Kensington
slot and a security cable.

Note:

Contact your vendor for details on purchasing a suitable Kensington security cable.

The security lock corresponds to Kensington’s MicroSaver Security System. If you have any
comment, contact: Kensington, 2853 Campus Drive, San Mateo, CA 94403, U.S.A. Tel: 800-535­4242, http://www.Kensington.com.

Using the Security Chain Lock

In addition to the password protection function and the Kensington lock, the Security Chain Opening
helps protect the PROJECTOR from unauthorized use.

See the following picture.

— 60 —

TROUBLESHOOTING

Common problems and solutions

These guidelines provide tips to deal with problems you may encounter while using the projector. If
the problem remains unsolved, contact your dealer for assistance.

Often after time spent troubleshooting, the problem is traced to something as simple as a loose
connection. Check the following before proceeding to the problem-specific solutions.

 Use some other electrical device to confirm that the electrical outlet is working.
 Ensure the projector is turned on.
 Ensure all connections are securely attached.
 Ensure the attached device is turned on.
 Ensure a connected PC is not in suspending mode.
 Ensure a connected notebook computer is configured for an external display.

(This is usually done by pressing an Fn-key combination on the notebook.)

Tips for Troubleshooting

In each problem-specific section, try the steps in the order suggested. This may help you to solve the
problem more quickly.

Try to pin point the problem and thus avoid replacing non-defective parts.
For example, if you replace batteries and the problem remains, put the original batteries back and go
to the next step.

Keep a record of the steps you take when troubleshooting: The information may be useful when
calling for technical support or for passing on to service personnel.

– 61 –

LED Error Messages

ERROR CODE MESSAGES

POWER LED

TEMP LED

READY LED

RED

BLUE

RED

RED

System Initial

Flash － OFF

OFF

Ready to Power on (Standby)

ON － OFF

OFF

System Power on

Flash － OFF

OFF

Lamp Lit , System stable

ON

OFF

ON

Cooling

Flash － OFF

OFF

Over Temperature

ON － ON

OFF

Thermal Break Sensor error

4 blinks － OFF

OFF

Lamp Fail

5 blinks － OFF

ON

Lamp Temperature shut down

5 blinks － OFF

1 blinks

Lamp Short circuit in output detected

5 blinks － OFF

2 blinks

Lamp End of lamp life detected

5 blinks － OFF

3 blinks

Lamp did not ignite

5 blinks － OFF

4 blinks

Lamp extinguished during normal operation

5 blinks － OFF

5 blinks

Lamp extinguished during run-up phase

5 blinks － OFF

6 blinks

Lamp voltage got error

5 blinks － OFF

7 blinks

Lamp ballast got error

5 blinks － OFF

8 blinks

Ballast watt value is out of range
(Lamp Normal & Eco mode)

5 blinks － OFF

9 blinks

Lamp ballast Communication error

5 blinks － OFF

10 blinks

Lamp ballast power error

5 blinks － OFF

11 blinks

Fan-1 error

6 blinks － OFF

1 blinks

Fan-2 error

6 blinks － OFF

2 blinks

Fan-3 error

6 blinks － OFF

3 blinks

Fan-4 error

6 blinks － OFF

4 blinks

Fan-5 error

6 blinks － OFF

5 blinks

Case Open

7 blinks － OFF

OFF

DAD1000 error

8 blinks － OFF

OFF

Color wheel error

9 blinks － OFF

OFF

In the event of an error, please disconnect the AC power cord and wait for one (1) minute before restarting
the projector. If the Power or Ready LEDs are still blinking or any other situation that isn't listed in the chart
above, please contact your service center.

Image Problems

Problem: No image appears on the screen

1. Verify the settings on your notebook or desktop PC.

2. Turn off all equipment and power up again in the correct order.

Problem: The image is blurred

1. Adjust the Focus on the projector.

2. Press the Auto button on the remote control.

3. Ensure the projector-to-screen distance is within the specified range.

4. Check that the projector lens is clean.

— 62 —

Problem: The image is wider at the top or bottom (trapezoid effect)

1. Position the projector so it is as perpendicular to the screen as possible.

2. Use the Keystone button on the remote control to correct the problem.

Problem: The image is reversed

Check the Projection setting on the Settings 1 menu of the OSD.

Problem: The image is streaked

1. Set the Frequency and Tracking settings on the Image->Computer menu of the OSD to the
default settings.

2. To ensure the problem is not caused by a connected PC’s video card, connect to another

computer.

Problem: The image is flat with no contrast

Adjust the Contrast setting on the Image menu of the OSD.

Problem: The color of the projected image does not match the source image.

Adjust the Color Temperature and Gamma settings on the Image->Advanced menu of the OSD.

Lamp Problems

Problem: There is no light from the projector

1. Check that the power cable is securely connected.

2. Ensure the power source is good by testing with another electrical device.

3. Restart the projector in the correct order and check that the Power LED is on.

4. If you have replaced the lamp recently, try resetting the lamp connections.

5. Replace the lamp module.

6. Put the old lamp back in the projector and have the projector serviced.

Problem: The lamp goes off

1. Power surges can cause the lamp to turn off. Re-plug power cord. When the Power LED is on,
press the power button.

2. Replace the lamp module.

3. Put the old lamp back in the projector and have the projector serviced.

Remote Control Problems

Problem: The projector does not respond to the remote control

1. Direct the remote control towards remote sensor on the projector.

2. Ensure the path between remote and sensor is not obstructed.

3. Turn off any fluorescent lights in the room.

4. Check the battery polarity.

5. Replace the battery.

6. Turn off other Infrared-enabled devices in the vicinity.

7. Have the remote control serviced.

– 63 –

Audio Problems

Problem: There is no sound

1. Adjust the volume on the remote control.

2. Adjust the volume of the audio source.

3. Check the audio cable connection.

4. Test the source audio output with other speakers.

5. Have the projector serviced.

Problem: The sound is distorted

1. Check the audio cable connection.

2. Test the source audio output with other speakers.

3. Have the projector serviced.

Having the Projector Serviced

If you are unable to solve the problem, you should have the projector serviced. Pack the projector in
the original carton. Include a description of the problem and a checklist of the steps you took when
trying to fix the problem: The information may be useful to service personnel. For servicing, return the
projector to the place you purchased it.

— 64 —

HDMI Q & A

Q. What is the difference between a “Standard” HDMI cable and a “High-Speed” HDMI

cable?

Recently, HDMI Licensing, LLC announced that cables would be tested as Standard or High-Speed
cables.

˙Standard (or “category 1”) HDMI cables have been tested to perform at speeds of 75Mhz or up to

2.25Gbps, which is the equivalent of a 720p/1080i signal.

˙High Speed (or “category 2”) HDMI cables have been tested to perform at speeds of 340Mhz or up

to 10.2Gbps, which is the highest bandwidth currently available over an HDMI cable and can
successfully handle 1080p signals including those at increased color depths and/or increased
refresh rates from the Source. High-Speed cables are also able to accommodate higher resolution
displays, such as WQXGA cinema monitors (resolution of 2560 x 1600).

Q. How do I run HDMI cables longer than 10 meters?

There are many HDMI Adopters working on HDMI solutions that extend a cable’s effective distance
from the typical 10 meter range to much longer lengths. These companies manufacture a variety of
solutions that include active cables (active electronics built into cables that boost and extend the
cable’s signal), repeaters, amplifiers as well as CAT5/6 and fiber solutions.

Q. How can I tell if a cable is an HDMI certified cable?

All HDMI products are required to be certified by the manufacturer as part of the HDMI Compliance
Test Specification. However, there may be instances where cables bearing the HDMI logo are
available but have not been properly tested. HDMI Licensing, LLC actively investigates these
instances to ensure that the HDMI trademark is properly used in the market. We recommend that
consumers buy their cables from a reputable source and a company that is trusted.

For more detail information check http://www.hdmi.org/learningcenter/faq.aspx#49

– 65 –

Specifications

Projection distance

Projection methods

NTSC (M, 3.58/4.43 MHz), PAL (B, D, G, H, I, M, N),

SECAM (B, D, G, K, K1, L)

Safety certification

Lamp

Security

Model H5095

Display type

Resolution

Projection screen size

Projection lens

Throw ratio

Vertical keystone correction

Front, Rear, Desktop/Ceiling (Rear, Front)

Data compatibility

SDTV/EDTV/ HDTV

Video compatibility

VGA, SVGA, XGA, SXGA, SXGA+, UXGA, WUXGA@60hz, Mac

480i, 576i, 480p, 576p, 720p, 1080i, 1080p

HDP2350

0.65” 1080P DC2 TypeA

1920x1080

1.5 meters ~ 7 meters

35.1” ~ 205.3”

Manual Zoom

1.54 ~ 1.93

±40°

SPECIFICATIONS

H-Sync

V-Sync

Operation temperature

Dimensions

AC Input

Power consumption

Audio speaker

Input Terminals

Output Terminals

Control Terminals

15, 31-91.4kHz

24~30Hz, 47 ~ 120Hz

FCC-B, cUL, UL, CE, C-tick, CCC, KC, CB, EAC

5° ~ 35°C

431.11mm (W) x 344.16mm (D) x 180.57mm (H)

AC Universal 100 – 240V

370W (Normal), 300W (ECO), <0.5W (Standby), < 2W (on by Lan)

280W (Normal) / 230W (Eco)

3W x 2

VGA x 2

DisplayPort x 1

DVI-D x 1

S-Video x 1

Component x 1

Composite video x 1

HDMI x 1

RCA stereo x 2

Mini-jack stereo x 2

VGA x 1

PC audio out x 1

RS-232C

RJ45

Screen trigger: DC Jack x 1 (DC12V 200mA output function)

wire remote

USB (type B) only for service/mouse control

USB (type A) only for power supply; WHDI

3D sync

Kensington lock

— 66 —

Projection Distance vs. Projection Size (1080P)

TELE

WIDE

Distance (m)

1.71

3.42

4.27

8.55

1.70

3.41

6.82

10.23

Diagonal (")

40

80

100

200

50

100

200

300(*)

Image Width (mm)

886

1771

2214

4428

1107

2214

4428

6641

Image Height (mm)

498

996

1245

2491

623

1245

2491

3736

h (mm)

249

498

623

1245

311

623

1245

1868

O (mm)

299

598

747

1494

374

747

1494

2241

A (mm)

50

100

125

249

62

125

249

374

TELE

WIDE

Distance (m)

2.57

6.42

12.84

19.26

2.14

6.41

12.82

19.23

Diagonal (")

40

100

200

300

50

150

300

450

Image Width (mm)

886

2214

4428

6641

1107

3321

6641

9962

Image Height (mm)

498

1245

2491

3736

623

1868

3736

5604

h (mm)

249

623

1245

1868

311

934

1868

2802

O (mm)

299

747

1494

2241

374

1121

2241

3362

A (mm)

50

125

249

374

62

187

374

560



V-Sync

Projection Distance

h

h

O

Image Height

A

Projection Distance and Size Table

Standard projection lens: TR: 1.54 ~ 1.93; offset=60%

Note:

(*) Overdrive.

Long throw projection lens: TR: 1.93 ~ 2.9; offset=60%

– 67 –

New Short throw projection lens: TR: 0.778; offset=60%

TELE

Distance (m)

0.69

1.38

1.72

2.58

Diagonal (")

40

80

100

150

Image Width (mm)

886

1771

2214

3321

Image Height (mm)

498

996

1245

1868

h (mm)

249

498

623

934

O (mm)

299

598

747

1121

A (mm)

50

100

125

187

TELE

WIDE

Distance (m)

1.15

2.88

5.76

8.92

1.22

3.65

7.31

9.01

Diagonal (")

40

100

200

310

50

150

300

370

Image Width (mm)

886

2214

4428

6863

1107

3321

6641

8191

Image Height (mm)

498

1245

2491

3860

623

1868

3736

4607

h (mm)

249

623

1245

1930

311

934

1868

2304

O (mm)

299

747

1494

2316

374

1121

2241

2764

A (mm)

50

125

249

386

62

187

374

461

TELE

WIDE

Distance (m)

3.32

11.07

16.60

19.92

3.32

6.64

13.28

19.92

Diagonal (")

30

100

150

180

50

100

200

300

Image Width (mm)

664

2214

3321

3985

1107

2214

4428

6641

Image Height (mm)

374

1245

1868

2241

623

1245

2491

3736

h (mm)

187

623

934

1121

311

623

1245

1868

O (mm)

224

747

1121

1345

374

747

1494

2241

A (mm)

37

125

187

224

62

125

249

374

Semi Short throw projection lens: TR: 1.1 ~ 1.3; offset=60%

Super Long throw projection lens: TR: 3 ~ 5; offset=60%

offset % = O/(2xh) × 100%
O=A+h
h=(1/2) × (image height)

— 68 —

Timing Mode Table

Signal

Resolution

H-Sync

(KHz)

V-Sync

(Hz)

Composite

S-Video

Component

RGB

(Analog)

DP/DVI

HDMI (Digital)

NTSC － 15.7

60.0

○

－ － －

PAL/SECAM

－

15.6

50.0

○

－ － －

VESA

640 x 400

37.9

85.1

－

－

○

○

720 x 400

31.5

70.1

－

－

○

○

720 x 400

37.9

85.0

－

－

○

○

640 x 480

31.5

60.0

－

－

○

○

640 x 480

37.9

72.8

－

－

○

○

640 x 480

37.5

75.0

－

－

○

○

640 x 480

43.3

85.0

－

－

○

○

800 x 600

35.2

56.3

－

－

○

○

800 x 600

37.9

60.3

－

－

○

○

800 x 600

46.9

75.0

－

－

○

○

800 x 600

48.1

72.2

－

－

○

○

800 x 600

53.7

85.1

－

－

○

○

800 x 600

76.3

120.0

－

－

○

○

1024 x 576

35.8

60.0

－

－

○

○

1024 x 600

37.3

60.0

－

－

○

○

1024 x 600

41.5

65.0

－

－

○

○

1024 x 768

48.4

60.0

－

－

○

○

1024 x 768

56.5

70.1

－

－

○

○

1024 x 768

60.0

75.0

－

－

○

○

1024 x 768

68.7

85.0

－

－

○

○

1024 x 768

97.6

120.0

－

－

○

○

1024 x 768

99.0

120.0

－

－

○

○

1152 x 864

67.5

75.0

－

－

○

○

1280 x 720

45.0

60.0

－

－

○

○

1280 x 720

90.0

120.0

－

－

○

○

1280 x 768

47.4

60.0

－

－

○

○

1280 x 768

47.8

59.9

－

－

○

○

1280 x 800

49.7

59.8

－

－

○

○

1280 x 800

62.8

74.9

－

－

○

○

1280 x 800

71.6

84.9

－

－

○

○

1280 x 800

101.6

119.9

－

－

○

○

1280 x 1024

64.0

60.0

－

－

○

○

1280 x 1024

80.0

75.0

－

－

○

○

1280 x 1024

91.1

85.0

－

－

○

○

1280 x 960

60.0

60.0

－

－

○

○

1280 x 960

85.9

85.0

－

－

○

○

1360 x 768

47.7

60.0

－

－

○

○

1400 x 1050

65.3

60.0

－

－

○

○

1440 x 900

55.5

59.9

－

－

○

○

1440 x 900

55.9

59.9

－

－

○

○

1440 x 900

70.6

75.0

－

－

○

○

1600 x1200

75.0

60.0

－

－

○

○

– 69 –

Signal

Resolution

H-Sync

(KHz)

V-Sync

(Hz)

Composite

S-Video

Component

RGB

(Analog)

DP/DVI

HDMI (Digital)

1680 x 1050

64.7

59.9

－

－

○

○

1680 x 1050

65.3

60.0

－

－

○

○

1920 x 1200

74.0

60.0

－

－

○

○

1920 x 1080

67.5

60.0

－

－

○

○

Apple
Macintosh

640 x 480

35.0

66.7

－

－

○

○

832 x 624

49.7

74.5

－

－

○

○

1024 x 768

60.2

74.9

－

－

○

○

1152 x 870

68.7

75.1

－

－

○

○

SDTV

480i

15.7

60.0 － ○ － ○

576i

15.6

50.0 － ○ － ○

EDTV

576p

31.3

50.0 － ○ － ○

480p

31.5

60.0 － ○ － ○

HDTV

720p

37.5

50.0 － ○ － ○

720p

45.0

60.0 － ○ － ○

1080i

33.8

60.0 － ○ － ○

1080i

28.1

50.0 － ○ － ○

1080p

27.0

24.0 － ○ － ○

1080p

28.0

25.0 － ○ － ○

1080p

33.7

30.0 － ○ － ○

1080p

56.3

50.0 － ○ － ○

1080p

67.5

60.0 － ○ － ○

O: Frequency supported
—: Frequency not supported

Resolution others than native resolution may be display with uneven size of text or line.

★ The color of mean Displayable only. (4:3 only)
★ The color of mean may have a little noise is acceptable, Because video mode sync don’t

auto adjustment.

★ HDTV timing main check tool is DVD player, VG828 is secondary.

— 70 —

Projector Dimensions

431.11mm

16.97"

323.26mm

12.73"

344.16mm

13.55"

161.51mm

6.36"

180.57mm

7.11"

– 71 –

REGULATORY COMPLIANCE

FCC Warning

This equipment has been tested and found to comply with the limits for a Class B digital device
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his/her own expense.

Changes or modifications not expressly approved by the parties responsible for compliance could
void the user’s authority to operate the equipment.

Canada

This class B digital apparatus complies with Canadian ICES-003.

Safety Certifications

FCC-B, cUL, UL, CE, C-tick, CCC, KC, CB, EAC

— 72 —

RS-232C Protocol

Baud rate:

9600

Parity check:

None

Data bit:

8

Stop bit:

1

Flow Control

None

Header code

Command code

Data code

End code

HEX

Command

Data

0Dh

ASCII

‘V’

Command

Data

CR

Command Group 00

ASCII

HEX

Function

Description

Return Result

VXXS0001

56h Xh Xh 53h 30h 30h 30h 31h 0Dh

Power On

P/F

VXXS0002

56h Xh Xh 53h 30h 30h 30h 32h 0Dh

Power Off

P/F

VXXS0003

56h Xh Xh 53h 30h 30h 30h 33h 0Dh

Resync

P/F

VXXG0004

56h Xh Xh 47h 30h 30h 30h 34h 0Dh

Get Lamp Hours

Pn/F

VXXS0006

56h Xh Xh 53h 30h 30h 30h 36h 0Dh

System Reset

P/F

VXXG0007

56h Xh Xh 47h 30h 30h 30h 37h 0Dh

Get System Status

0:Reset
1:Standby
2:Operation
3:Cooling

Pn/F
VXXG0008

56h Xh Xh 47h 30h 30h 30h 38h 0Dh

Get F/W Version

Pn/F

VXXG0009

56h Xh Xh 47h 30h 30h 30h 39h 0Dh

Get Alter EMail

Pn/F

VXXS0009n

56h Xh Xh 53h 30h 30h 30h 39h nh 0Dh

Set Alter Email

n=xxxxxx@xxx
x.xxx.xx

P/F

RS232 Setting

Control Command Structure

Operation Command

APPENDIX I

Note:
"CR" mean Carriage Return
XX=00-98, projector's ID, XX=99 is for all projectors
Return Result P=Pass / F=Fail
n: 0:Disable/1: Enable/Value(0~9999)

– 73 –

Command Group 01

ASCII

HEX

Function

Description

Return Value

VXXG0101

56h Xh Xh 47h 30h 31h 30h 31h 0Dh

Get Brightness

n=0~100

Pn/F

VXXS0101n

56h Xh Xh 53h 30h 31h 30h 31h nh 0Dh

Set Brightness

n=0~100

P/F

VXXG0102

56h Xh Xh 47h 30h 31h 30h 32h 0Dh

Get Contrast

n=0~100

Pn/F

VXXS0102n

56h Xh Xh 53h 30h 31h 30h 32h nh 0Dh

Set Contrast

n=0~100

P/F

VXXG0103

56h Xh Xh 47h 30h 31h 30h 33h 0Dh

Get Color

n=0~100

Pn/F

VXXS0103n

56h Xh Xh 53h 30h 31h 30h 33h nh 0Dh

Set Color

n=0~100

P/F

VXXG0104

56h Xh Xh 47h 30h 31h 30h 34h 0Dh

Get Tint

n=0~100

Pn/F

VXXS0104n

56h Xh Xh 53h 30h 31h 30h 34h nh 0Dh

Set Tint

n=0~100

P/F

VXXG0105

56h Xh Xh 47h 30h 31h 30h 35h 0Dh

Get Sharpness

0~31

Pn/F

VXXS0105n

56h Xh Xh 53h 30h 31h 30h 35h nh 0Dh

Set Sharpness

0~31

P/F

VXXG0106

56h Xh Xh 47h 30h 31h 30h 36h 0Dh

Get Color
Temperature

0:Warm
1:Normal
2:Cold

Pn/F

VXXS0106n

56h Xh Xh 53h 30h 31h 30h 36h nh 0Dh

Set Color
Temperature

0:Warm
1:Normal
2:Cold

P/F

VXXG0107

56h Xh Xh 47h 30h 31h 30h 37h 0Dh

Get Gamma

0:1.8
1:2.0
2:2.2
3:2.4
4:B&W
5:Linear

Pn/F

VXXS0107n

56h Xh Xh 53h 30h 31h 30h 37h nh 0Dh

Set Gamma

0:1.8
1:2.0
2:2.2
3:2.4
4:B&W
5:Linear

P/F

Command Group 02

ASCII

HEX

Function

Description

Return Value

VXXS0201

56h Xh Xh 53h 30h 32h 30h 31h 0Dh

Select RGB

P/F

VXXS0202

56h Xh Xh 53h 30h 32h 30h 32h 0Dh

Select RGB2

P/F

VXXS0203

56h Xh Xh 53h 30h 32h 30h 33h 0Dh

Select DVI

P/F

VXXS0204

56h Xh Xh 53h 30h 32h 30h 34h 0Dh

Select Video

P/F

VXXS0205

56h Xh Xh 53h 30h 32h 30h 35h 0Dh

Select S-Video

P/F

VXXS0206

56h Xh Xh 53h 30h 32h 30h 36h 0Dh

Select HDMI

P/F

VXXS0208

56h Xh Xh 53h 30h 32h 30h 38h 0Dh

Select
Component

P/F

VXXS0210

56h Xh Xh 53h 30h 32h 31h 30h 0Dh

Select
Display Port

P/F

— 74 —

Command Group 02

ASCII

HEX

Function

Description

Return Value

VXXG0220

56h Xh Xh 47h 30h 32h 32h 30h 0Dh

Get Current
Source

Return
1:RGB
2:RGB2
3:DVI
4:Video
5:S-Video
6:HDMI
7: Component
8: Display Port

Pn/F

Command Group 03

ASCII

HEX

Function

Description

Return Value

VXXG0301

56h Xh Xh 47h 30h 33h 30h 31h 0Dh

Get Aspect Ratio

0:Fill
1:4:3
2:16:9
3:Letter Box
4:Native
5:Theater Zoom

Pn/F

VXXS0301n

56h Xh Xh 53h 30h 33h 30h 31h nh 0Dh

Set Aspect Ratio

0:Fill
1:4:3
2:16:9
3:Letter Box
4:Native
5:Theater Zoom

P/F
VXXG0302

56h Xh Xh 47h 30h 33h 30h 32h 0Dh

Get Blank

0:Unblank
1:Blank

Pn/F

VXXS0302n

56h Xh Xh 53h 30h 33h 30h 32h nh 0Dh

Set Blank

0:Unblank
1:Blank

P/F

VXXG0304

56h Xh Xh 47h 30h 33h 30h 34h 0Dh

Get Freeze

0:Unfreeze
1:Freeze

Pn/F

VXXS0304n

56h Xh Xh 53h 30h 33h 30h 34h nh 0Dh

Set Freeze

0:Unfreeze
1:Freeze

P/F

VXXG0305

56h Xh Xh 47h 30h 33h 30h 35h 0Dh

Get Volume

n=0~10

Pn/F

VXXS0305n

56h Xh Xh 53h 30h 33h 30h 35h nh 0Dh

Set Volume

n=0~10

P/F

VXXG0308

56h Xh Xh 47h 30h 33h 30h 38h 0Dh

Get Projection
Mode

0:Front
1:Rear
2:Ceiling
3:Rear+Ceiling

Pn/F

VXXS0308n

56h Xh Xh 53h 30h 33h 30h 38h nh 0Dh

Set Projection
Mode

0:Front
1:Rear
2:Ceiling
3:Rear+Ceiling

P/F
VXXG0309

56h Xh Xh 47h 30h 33h 30h 39h 0Dh

Get Vertical
Keystone Value

n=-40~+40

Pn/F

VXXS0309n

56h Xh Xh 53h 30h 33h 30h 39h nh 0Dh

Set Vertical
Keystone Value

n=-40~+40

P/F

VXXG0311

56h Xh Xh 47h 30h 33h 31h 31h 0Dh

Get Zoom

n=-10~+10

Pn/F

VXXS0311n

56h Xh Xh 53h 30h 33h 31h 31h nh 0Dh

Set Zoom

n=-10~+10

P/F

VXXG0315

56h Xh Xh 47h 30h 33h 31h 35h 0Dh

Get 3D Sync

0:Off
1:DLP-Link
2:IR

Pn/F

– 75 –

Command Group 03

0:Off

2:IR

0:Off

0:Off
1:On

0:Frame

Packing

0:Frame

Packing

ASCII HEX Function Description Return Value

VXXS0315n 56h Xh Xh 53h 30h 33h 31h 35h nh 0Dh Set 3D Sync

VXXG0316 56h Xh Xh 47h 30h 33h 31h 36h 0Dh Get 3D Sync Invert

VXXS0316n 56h Xh Xh 53h 30h 33h 31h 36h nh 0Dh Set 3D Sync Invert

VXXG0317 56h Xh Xh 47h 30h 33h 31h 37h 0Dh Get 3D Format

VXXS0317n 56h Xh Xh 53h 30h 33h 31h 37h nh 0Dh Set 3D Format

1:DLP-Link

1:On

Sequential
1:Top/Bottom
2:Side-By-Side
3:Frame

Sequential
1:Top/Bottom
2:Side-By-Side
3:Frame

P/F

Pn/F

P/F

Pn/F

P/F

Knoll Systems

14-7163 Vantage Way, Delta BC V4G 1N1, Canada
145 Tyee Drive, Point Roberrts, WA 98281, USA

— 76 —