Knoll Systems HDO2250b User Manual
HDO2250
DLP™ 3D Projector
Users Manual v1.0
D
9
Series
— i —
Copyright
This publication, including all photographs, illustrations and software, is protected under international copyright laws, with all rights reserved. Neither this manual, nor any of the material contained herein, may be
reproduced without written consent of the author.
© Copyright 2015
Disclaimer
The information in this document is subject to change without notice. The manufacturer makes no
representations or warranties with respect to the contents hereof and specifically disclaims any implied
warranties of merchantability or fitness for any particular purpose. The manufacturer reserves the right to
revise this publication and to make changes from time to time in the content hereof without obligation of
the manufacturer to notify any person of such revision or changes.
Trademark Recognition
Kensington is a U.S. registered trademark of ACCO Brand Corporation with issued registrations and
pending applications in other countries throughout the world.
HDMI, the HDMI Logo, and High-Definition Multimedia Interface are trademarks or
registered trademarks of HDMI Licensing LLC in the United States and other
countries.
All other product names used in this manual are the properties of their respective owners and are
acknowledged.
— ii —
D
D
D
L
L
L
P
P
P
P
P
P
r
r
r
o
o
o
j
j
j
e
e
e
c
c
c
t
t
t
o
o
o
r
r
r
—
—
—
U
U
U
s
s
s
e
e
e
r
r
r
’
’
’
s
s
s
M
M
M
a
a
a
n
n
n
u
u
u
a
a
a
l
l
l
Important Safety Information
Important:
It is strongly recommended that you read this section carefully before using the projector. These
safety and usage instructions will ensure that you enjoy many years of safe use of the projector.
Keep this manual for future reference.
Symbols Used
Warning symbols are used on the unit and in this manual to alert you of hazardous situations.
The following styles are used in this manual to alert you to important information.
Note:
Provides additional information on the topic at hand.
Important:
Provides additional information that should not be overlooked.
Caution:
Alerts you to situations that may damage the unit.
Warning:
Alerts you to situations that may damage the unit, create a hazardous environment, or cause personal injury.
Throughout this manual, component parts and items in the OSD menus are denoted in bold font as in this
example:
“Push the MENU button on the remote control to open the DISPLAY menu.”
General Safety Information
Do not open the unit case. Aside from the projection lamp, there are no user-serviceable parts in
the unit. For servicing, contact qualified service personnel.
Follow all warnings and cautions in this manual and on the unit case.
The projection lamp is extremely bright by design. To avoid damage to eyes, do not look into the
lens when the lamp is on.
Do not place the unit on an unstable surface, cart, or stand.
Avoid using the system near water, in direct sunlight, or near a heating device.
Do not place heavy objects such as books or bags on the unit.
P
P
P
r
r
r
e
e
e
f
f
f
a
a
a
c
c
c
e
e
e
Projector Installation Notice
Place the projector in a horizontal position
The tilt angle of the projector should not exceed 15 degrees, nor should the projector be installed in
any way other than the desktop and ceiling mount, otherwise lamp life could decrease dramatically.
Allow at least 50 cm clearance around the exhaust vent.
Ensure that the intake vents do not recycle hot air from the exhaust vent.
When operating the projector in an enclosed space, ensure that the surrounding air temperature
within the enclosure does not exceed 5 – 35°C while the projector is running, and the air intake and
exhaust vents are unobstructed.
All enclosures should pass a certified thermal evaluation to ensure that the projector does not
recycle exhaust air, as this may cause the device to shutdown even if the enclosure temperature is
with the acceptable 5 – 35°C range.
Power Safety
Only use the supplied power cord.
Do not place anything on the power cord. Place the power cord where it will not be in the way of
foot traffic.
Remove the batteries from the remote control when storing or not in use for a prolonged period.
D
D
D
L
L
L
P
P
P
P
P
P
r
r
r
o
o
o
j
j
j
e
e
e
c
c
c
t
t
t
o
o
o
r
r
r
Verify Installation Location
To supply power, the 3-blade (with earthing lead) socket should be used to ensure proper
grounding and equalized ground potential for all of the equipment in the Projector System.
The power code provided with the Projector should be used. In case of any missing item, other
qualified 3-blade (with earthing lead) power cord can be used as substitution; however, do not use
2-blade power cord.
Verify if the voltage is stable, grounded properly and there is no electricity leakage.
Measure total power consumption which should not higher the safety capacity and avoid safety
issue and short circuit.
Turn on Altitude Mode when located in high altitude areas
The projector can only be installed upright or inverted.
When installation the bracket, make sure the weight limit is not exceed and firmly secured.
Avoid installing near air conditioner duct or subwoofer.
Avoid installing at high temperature, insufficient cooling and heavy dust locations.
Keep your product away from fluorescent lamps to avoid malfunction caused by IR interference
The VGA IN connector should be connected to the VGA IN port. Note that it should be inserted
tightly, with the screws on both sides securely fastened to ensure proper connection of the signal
wire for achieving optimal display effect.
The AUDIO IN connector should be connected to the AUDIO IN port and CANNOT be connected to
AUDIO OUT or other ports like BNC, RCA; otherwise, it will lead to mute output and even DAMAGE
the port.
Install the projector above 200cm to avoid damage.
The power cord and signal cable should be connected before power on the projector. During the
projector starting and operating process, DO NOT insert or remove the signal cable or the power
cord to avoid damaging the projector.
Cooling notes
Air outlet
Make sure the air outlet is 50cm clear of any obstruction to ensure proper cooling.
Air outlet location should not be in front of the lens of other projector to avoid causing illusions.
Keep the outlet at least 100cm away from the inlets of other projectors
The projector generates a massive amount of heat during use. The internal fan dissipates the heat
of the projector when shutting down, and such process may continue for a certain period. After
the project enters STANDBY MODE status, press the AC power button to turn off the projector and
remove the power cord. DO NOT remove the power cord during the shutdown process, as it may
cause damage to the projector. In the meantime, the delayed heat radiating will also affect the
service life of the projector. The shutdown process may vary depending on the model used.
Whatever the case may be, be sure to NOT disconnect the power cord until the projector enters
the STANDBY status.
Air inlet
Make sure there is no object blocking air input within 30 cm.
Keep the inlet away from other heat sources
Avoid heavy dust areas
— iv —
—
—
—
U
U
U
s
s
s
e
e
e
r
r
r
’
’
’
s
s
s
M
M
M
a
a
a
n
n
n
u
u
u
a
a
a
l
l
l
Replacing the Lamp
Replacing the lamp can be hazardous if done incorrectly. See Replacing the Projection Lamp on page 37
for clear and safe instructions for this procedure. Before replacing the lamp:
Unplug the power cord.
Allow the lamp to cool for about one hour.
Caution:
In rare cases the lamp bulb may burn out during normal operation and cause glass dust or shards
to be discharged outward from the rear exhaust vent.
Do not inhale or do not touch glass dust or shards. Doing so could result in injury.
Always keep your face away from the exhaust vent so that you do not suffer from the gas and bro-
ken shards of the lamp.
Cleaning the Projector
Unplug the power cord before cleaning. See Cleaning the Projector on page 39.
Allow the lamp to cool for about one hour.
Regulatory Warnings
Before installing and using the projector, read the regulatory notices in the Regulatory Compliance section
on page 51.
Important Recycle Instructions:
Lamp(s) inside this product contain mercury. This product may contain other electronic waste that
can be hazardous if not disposed of properly. Recycle or dispose in accordance with local, state, or federal
Laws. For more information, contact the Electronic Industries Alliance at WWW.EIAE.ORG. For lamp
specific disposal information check WWW.LAMPRECYCLE.ORG.
Symbol Explanations
DISPOSAL: Do not use household or municipal waste collection services for
disposal of electrical and electronic equipment. EU countries require the use
of separate recycling collection services.
– v –
P
P
P
r
r
r
e
e
e
f
f
f
a
a
a
c
c
c
e
e
e
GETTING STARTED .......................................................................................................................................................... 1
PACKING CHECKLIST ........................................................................................................................................................... 1
VIEWS OF P
ROJECTOR PARTS
............................................................................................................................................... 2
Front-right View ............................................................................................................................................................. 2
Top view—On-screen Display (OSD) buttons and LEDs ............................................................................................... 3
Rear view ........................................................................................................................................................................ 4
Bottom view..................................................................................................................................................................... 5
REMOTE CONTROL PARTS ................................................................................................................................................... 6
REMOTE CONTROL OPERATING R
PROJECTOR AND REMOTE C
SETUP AND OPERATION ................................................................................................................................................. 9
INSERTING THE REMOTE CONTROL B
ANGE
ONTROL
............................................................................................................................... 8
BUTTONS.................................................................................................................... 8
ATTERIES
CONNECTING INPUT DEVICES ............................................................................................................................................ 10
STARTING AND SHUTTING DOWN THE P
ADJUSTING THE PROJECTOR
L
EVEL
ADJUSTING THE ZOOM RING, FOCUS
ADJUSTING THE VOLUME .................................................................................................................................................. 15
ON-SCREEN DISPLAY (OSD) MENU SETTINGS....................................................................................................... 16
ROJECTOR
................................................................................................................................... 13
AND
OSD MENU CONTROLS ..................................................................................................................................................... 16
Navigating the OSD ...................................................................................................................................................... 16
SETTING THE OSD L
ANGUAGE
.......................................................................................................................................... 17
OSD MENU OVERVIEW ..................................................................................................................................................... 18
PICTURE>>BASIC MENU................................................................................................................................................. 19
PICTURE>>ADVANCED MENU ........................................................................................................................................ 20
HSG Adjustment............................................................................................................................................................ 21
DISPLAY MENU............................................................................................................................................................... 22
PC Detail Adjustment.................................................................................................................................................... 23
SETUP>>BASIC MENU ..................................................................................................................................................... 24
Menu Settings................................................................................................................................................................ 25
Source ........................................................................................................................................................................... 25
Lan Control Settings ..................................................................................................................................................... 26
SETUP>>ADVANCED MENU ............................................................................................................................................ 32
Audio ............................................................................................................................................................................. 33
Lamp ............................................................................................................................................................................. 33
HDMI ............................................................................................................................................................................ 34
Closed Caption.............................................................................................................................................................. 34
Presentation Timer........................................................................................................................................................ 35
STATUS MENU ................................................................................................................................................................ 36
MAINTENANCE AND SECURITY................................................................................................................................. 37
REPLACING THE PROJECTION L
CLEANING THE P
ROJECTOR
AMP
................................................................................................................................... 37
................................................................................................................................................ 39
Cleaning the Lens ......................................................................................................................................................... 39
Cleaning the Case ......................................................................................................................................................... 39
USING THE KENSINGTON® LOCK ....................................................................................................................................... 40
TROUBLESHOOTING ..................................................................................................................................................... 41
COMMON PROBLEMS AND
SOLUTIONS
............................................................................................................................... 41
TIPS FOR TROUBLESHOOTING ............................................................................................................................................ 41
LED ERROR MESSAGES .................................................................................................................................................... 42
IMAGE P
ROBLEMS
.............................................................................................................................................................. 42
LAMP PROBLEMS ............................................................................................................................................................... 43
REMOTE CONTROL PROBLEMS .......................................................................................................................................... 43
AUDIO PROBLEMS ............................................................................................................................................................. 44
HAVING THE PROJECTOR SERVICED .................................................................................................................................. 44
HDMI Q & A .................................................................................................................................................................... 45
Table of Contents
................................................................................................................... 9
............................................................................................................. 11
KEYSTONE........................................................................................................ 14
— vi —
D
D
D
L
L
L
P
P
P
P
P
P
r
r
r
o
o
o
j
j
j
e
e
e
c
c
c
t
t
t
o
o
o
r
r
r
—
—
—
U
U
U
s
s
s
e
e
e
r
r
r
’
’
’
s
s
s
M
M
M
a
a
a
n
n
n
u
u
u
a
a
a
l
l
l
SPECIFICATIONS............................................................................................................................................................. 46
S
PECIFICATIONS
PROJECTION DISTANCE VS. PROJECTION SIZE ................................................................................................................... 47
Projection Distance and Size Table .............................................................................................................................. 47
TIMING MODE TABLE ........................................................................................................................................................ 48
PROJECTOR DIMENSIONS ................................................................................................................................................... 50
REGULATORY COMPLIANCE ..................................................................................................................................... 51
FCC WARNING.................................................................................................................................................................. 51
CANADA ............................................................................................................................................................................ 51
SAFETY
C
................................................................................................................................................................. 46
ERTIFICATIONS
................................................................................................................................................... 51
– 1 –
D
D
D
L
L
L
P
P
P
P
P
P
r
r
r
o
o
o
j
j
j
e
e
e
c
c
c
t
t
t
o
o
o
r
r
r
–
–
–
U
U
U
s
s
s
e
e
e
r
r
r
’
’
’
s
s
s
M
M
M
a
a
a
n
n
n
u
u
u
a
a
a
l
l
l
G
ETTING STARTED
Packing Checklist
Carefully unpack the projector and check that the following items are included:
DLP PROJECTOR
R
EMOTE CONTROL
CD-ROM
VGA CABLE POWER CORD
WARRANTY CARD
(THIS USER’S MANUAL)
Contact your dealer immediately if any items are missing, appear damaged, or if the unit does not work. It
is recommended that you keep the original packing material should you ever need to return the
equipment for warranty service.
Caution:
Avoid using the projector in dusty environments.
– 2 –
ITEM L
ABEL
D
ESCRIPTION
SEE PAGE:
1.
Height-adjuster button
Push to release height adjuster
13
2.
Height adjuster
Adjusts level of projector
3.
Lens
Projection Lens
4.
IR receiver
Receive IR signal from remote control
6
5.
Focus ring
Focuses the projected image
14
6.
Zoom ring
Enlarges the projected image
7.
Function keys
See Top view—On-screen Display (OSD) buttons
3
D
D
D
L
L
L
P
P
P
P
P
P
r
r
r
o
o
o
j
j
j
e
e
e
c
c
c
t
t
t
o
o
o
r
r
r
—
—
—
U
U
U
s
s
s
e
e
e
r
r
r
’
’
’
s
s
s
M
M
M
a
a
a
n
n
n
u
u
u
a
a
a
l
l
l
Views of Projector Parts
Front-right View
1 2 3 4
5 6 7
and LEDs.
Important:
Ventilation openings on the projector allow for good air circulation, which keeps the projector lamp
cool. Do not obstruct any of the ventilation openings.
– 3 –
ITEM L
ABEL
D
ESCRIPTION
SEE
PAGE:
1.
(Power button)
Turns the projector On or Off.
11
2.
BLANK
Displays a blank screen and mutes audio
3.
◄ (Left cursor) /
Volume-
Navigates and changes settings in the OSD
Quick Menu – For Volume
16
4.
Enter
Enter or confirm highlighted OSD menu item
5.
MENU
Opens and exits OSD menus
6.
▲ (Up cursor) /
Keystone+
Navigates and changes settings in the OSD
Quick Menu – For Keystone
7.
AUTO
Optimizes image size, position, and resolution
8.
► (Right cursor) /
Volume+
Navigates and changes settings in the OSD
16
9.
SOURCE
Enter the Source menu
10
10.
▼ (Down cursor) /
Keystone-
Navigates and changes settings in the OSD
16
11.
READY LED
Red
Lamp is ready to be powered-on.
Flashing
Lamp is not ready (warming up/shutting down/cooling)
(see LED Error Messages on page 42)
12.
TEMP LED
Flashing
Error code
D
D
D
L
L
L
P
P
P
P
P
P
r
r
r
o
o
o
j
j
j
e
e
e
c
c
c
t
t
t
o
o
o
r
r
r
–
–
–
U
U
U
s
s
s
e
e
e
r
r
r
’
’
’
s
s
s
M
M
M
a
a
a
n
n
n
u
u
u
a
a
a
l
l
l
Top view—On-screen Display (OSD) buttons and LEDs
Quick Menu – For Volume
Quick Menu – For Keystone
– 4 –
D
D
D
L
L
L
P
P
P
P
P
P
r
r
r
o
o
o
j
j
j
e
e
e
c
c
c
t
t
t
o
o
o
r
r
r
—
—
—
U
U
U
s
s
s
e
e
e
r
r
r
’
’
’
s
s
s
M
M
M
a
a
a
n
n
n
u
u
u
a
a
a
l
l
l
Rear view
1 2 3
4 5 6
7 8 9
10 11
12
13
18
17
16
15
14
I
TEM
LABEL
DESCRIPTION
SEE PAGE
1.
AC IN
Connect the POWER cable
11
2.
(USB)
Connect the USB cable from a computer
3.
VGA OUT
Connect the RGB cable to a display
(Loop Thru only for VGA IN-1)
4.
LAN
Connect a LAN cable from Ethernet
5.
VGA IN 1
Connect the RGB cable from a computer or component device
6.
VGA IN 2
Connect the RGB cable from a computer or component device
7.
DP
Connect a DISPLAYPORT CABLE from a DISPLAYPORT device
8.
AUDIO IN
Connect an AUDIO cable from audio device
9.
HDMI 1 / 2
Connect the HDMI cable from a HDMI device
10.
3D SYNC
Connect the 3D IR glasses transmitter
12.
Speaker
Outputs audio sound
13.
Kensington Lock
Secure to permanent object with a Kensington® Lock
50
system
14.
VIDEO IN
Connect the COMPOSITE cable from a video device
16.
S-VIDEO IN
Connect the S-Video cable from a video device
17.
RS-232C
Connect RS-232 serial port cable for remote control
18.
AUDIO OUT
Connect an AUDIO cable to audio amplifier
When connected to the screen through a commercially available cable,
11. DC 12V TRIGGER the screen deploys automatically on startup of the projector. The screen
retracts when the projector is powered off (see notes below).
15. AUDIO IN (L and R) Connect the AUDIO cable from an audio device
– 5 –
Note:
If your video equipment has various input sources, it is recommended to connect in priority of
HDMI TM, component, S-Video, Composite for better picture quality.
– 6 –
D
D
D
L
L
L
P
P
P
P
P
P
r
r
r
o
o
o
j
j
j
e
e
e
c
c
c
t
t
t
o
o
o
r
r
r
–
–
–
U
U
U
s
s
s
e
e
e
r
r
r
’
’
’
s
s
s
M
M
M
a
a
a
n
n
n
u
u
u
a
a
a
l
l
l
ITEM L
ABEL
D
ESCRIPTION
SEE PAGE:
1.
Tilt adjustor
Rotate adjuster lever to adjust angle position.
13
2.
Ceiling support holes
Contact your dealer for information on mounting the projector on a ceiling
3.
Height adjustor
Adjuster drops down when adjuster button is pushed.
13
4.
Height adjustor button
Push to release adjustor.
Bottom view
Note:
When installing, ensure that you use only UL Listed ceiling mounts.
For ceiling installations, use approved mounting hardware and M4 screws with a maximum screw
depth of 6 mm (0.23 inch).
The construction of the ceiling mount must be of a suitable shape and strength. The ceiling mount
load capacity must exceed the weight of the installed equipment, and as an additional precaution
be capable of withstanding three times the weight of the equipment (not less than 5.15 kg) over a
period of 60 seconds.
– 7 –
D
D
D
L
L
L
P
P
P
P
P
P
r
r
r
o
o
o
j
j
j
e
e
e
c
c
c
t
t
t
o
o
o
r
r
r
—
—
—
U
U
U
s
s
s
e
e
e
r
r
r
’
’
’
s
s
s
M
M
M
a
a
a
n
n
n
u
u
u
a
a
a
l
l
l
30
29
1
2
28
3
27
4
5
6
26
7
8
25
9
10
24
11
12
23
13
14
22
15
21
16
17
20
18
19
Remote Control Parts
Important:
1. Avoid using the projector with bright fluorescent lighting turned on. Certain high-
frequency fluorescent lights can disrupt remote control operation.
2. Be sure nothing obstructs the path between the remote control and the projector. If the path
between the remote control and the projector is obstructed, you can bounce the signal off
certain reflective surfaces such as projector screens.
3. The buttons and keys on the projector have the same functions as the corresponding buttons
on the remote control. This user’s manual describes these functions.
– 8 –
P
P
P
r
r
r
o
o
o
j
j
j
e
e
e
c
c
c
t
t
t
o
o
o
r
r
r
–
–
–
U
U
U
s
s
s
e
e
e
r
r
r
’
’
’
s
s
s
M
M
M
a
a
a
n
n
n
u
u
u
a
a
a
l
l
l
ITEM
LABEL
DESCRIPTION
SEE PAGE
1.
Power OFF
Turns the projector off
11
2.
HDMI 2
Displays the HDMI 2 source selection
3.
PC Displays the PC source selection
4.
VIDEO
Displays the VIDEO source selection
5.
Up cursor /
Navigates and changes settings in the OSD
Keystone+
Quick Menu –For Keystone
6.
ENTER
Enters and confirms settings in the OSD
18
7.
Right cursor
Navigates and changes settings in the OSD
8.
Down cursor /
Navigates and changes settings in the OSD
Keystone-
Quick Menu –For Keystone
9.
ASPECT RATIO
Displays the ASPECT RATIO selections
10.
SOURCE
Detects the input device
11.
2D 3D
Toggle 3D function
12.
BRIGHT
Displays the brightness setting bar
13.
SHARP
Displays the sharpness setting bar
14.
COLOR
Displays the color setting bar
15.
TINT
Displays the tint setting bar
16.
BLANK
Makes the screen blank
17.
FREEZE
Freezes/unfreezes the on-screen picture
18.
AUTO
Auto adjustment for frequency, phase, and position
Turns on or off the remote control backlight for about 10 seconds.
19.
LIGHT
Pressing any other key while the backlight is on keeps the backlight on
for a further 10 seconds.
20.
VOL -
Adjusts volume
18
21.
VOL +
22.
MUTE
Mutes the built-in speaker
23.
CONTRAST
Displays the contrast settings bar
24.
PICTURE MODE
Changes the Display Mode setting
25.
MENU/ EXIT
Opens and exits the OSD
18
26.
Left cursor
Navigates and changes settings in the OSD
27.
COMP
Displays the Component source selection
28.
HDMI 1
Displays the HDMI 1 source selection
29.
Power ON
Turns the projector on
11
30.
IR transmitter
Transmits signals to projector
– 9 –
D
D
D
L
L
L
P
P
P
P
P
P
r
r
r
o
o
o
j
j
j
e
e
e
c
c
c
t
t
t
o
o
o
r
r
r
—
—
—
U
U
U
s
s
s
e
e
e
r
r
r
’
’
’
s
s
s
M
M
M
a
a
a
n
n
n
u
u
u
a
a
a
l
l
l
Remote Control Operating Range
The remote control uses infrared transmission to control the projector. It is not necessary to point the
remote directly at the projector. Provided you are not holding the remote perpendicular to the sides or
the rear of the projector, the remote will function well within a radius of about 7 meters (23 feet) and
15 degrees above or below the projector level. If the projector does not respond to the remote control,
move a little closer.
Projector and Remote Control Buttons
The projector can be operated using the remote control or the buttons on the top of the projector. All
operations can be carried out with the remote control; however, the buttons on the projector are
limited in use.
– 10 –
D
D
D
L
L
L
P
P
P
P
P
P
r
r
r
o
o
o
j
j
j
e
e
e
c
c
c
t
t
t
o
o
o
r
r
r
–
–
–
U
U
U
s
s
s
e
e
e
r
r
r
’
’
’
s
s
s
M
M
M
a
a
a
n
n
n
u
u
u
a
a
a
l
l
l
Inserting the Remote Control Batteries
Remove the battery compartment cover
1.
by sliding the cover in the direction of
the arrow.
Insert the battery with the positive side
2.
facing up.
S
ETUP AND
OPERATION
Replace the cover.
3.
Caution:
1. Only use AAA batteries (Alkaline batteries are recommended).
2. Dispose of used batteries according to local ordinance regulations.
3. Remove the batteries when not using the projector for prolonged periods.
– 11 –
D
D
D
L
L
L
P
P
P
P
P
P
r
r
r
o
o
o
j
j
j
e
e
e
c
c
c
t
t
t
o
o
o
r
r
r
–
–
–
U
U
U
s
s
s
e
e
e
r
r
r
’
’
’
s
s
s
M
M
M
a
a
a
n
n
n
u
u
u
a
a
a
l
l
l
Starting and Shutting down the Projector
Connect the power cord to the projector.
1.
Connect the other end to a wall outlet.
The POWER LED will be on.
Turn on the connected devices.
2.
3. Ensure the POWER LED displays a
solid blue and not a flashing blue. Then
press the POWER button to turn
the
projector.
The projector “knoll” splash screen
displays and connected devices are
detected.
If more than one input device is con-
4.
nected, press the SOURCE button and
use ▲▼ to scroll among devices.
on
HDMI 1 / HDMI 2: High-Definition Multimedia Interface 1 / 2
DisplayPort: Display Port
VGA 1 / VGA 2: Analog RGB1 / RGB 2
S-Video: Super video (Y/C separated)
Composite Video: Traditional composite video
Component is supported through the optional
RGB to Component adaptor.
– 12 –
D
D
D
L
L
L
P
P
P
P
P
P
r
r
r
o
o
o
j
j
j
e
e
e
c
c
c
t
t
t
o
o
o
r
r
r
—
—
—
U
U
U
s
s
s
e
e
e
r
r
r
’
’
’
s
s
s
M
M
M
a
a
a
n
n
n
u
u
u
a
a
a
l
l
l
5. When the “Power Power again” message
press the POWER button. The projector
begins cool down and turns off.
Caution:
Do not unplug the power cord until the READY LED stops flashing–indicating the projector has
cooled down.
– 13 –
P
P
P
r
r
r
o
o
o
j
j
j
e
e
e
c
c
c
t
t
t
o
o
o
r
r
r
–
–
–
U
U
U
s
s
s
e
e
e
r
r
r
’
’
’
s
s
s
M
M
M
a
a
a
n
n
n
u
u
u
a
a
a
l
l
l
Setting an Access Password (Security Lock)
You can use the four (arrow) buttons to set a password and prevent unauthorized use of the projector.
When enabled, the password must be entered after you power on the projector. (See Navigating the
OSD on page 18 and Setting the OSD Language on page 19 for help on using OSD menus.)
Important:
Keep the password in a safe place. Without the password, you will not be able to use the
projector. If you lose the password, contact your reseller for information on clearing the password.
1. Press the MENU button to open the
OSD menu.
Press the cursor ◄ to the Settings 1
2.
menu, press the cursor ▲▼ button to
select Advanced 1
Press (Enter) / ► to enter the
Advanced 1 sub menu. Press the
3.
cursor ▲▼ button to select Security
Lock.
Press the cursorenter ◄
4. Press the cursor button to enable
or disable the security lock
function.
A password dialog box automatically
appears.
– 14 –
5. You can use the cursor buttons
▲▼◄►
either on the keypad or IR remote
control for password entry. You can
use any combination including the
same arrow five times, but not less
than five.
Press the cursor buttons in any
order to set the password. Push the
MENU button to exit the dialog box.
6. The password confirm menu appears
when user presses the power-on key
in case the Security Lock is enabled.
Enter the password in the order you
set it at step 5. In case you forget the
password, please contact the service
center.
The service center will validate the
owner and help reset the password.
– 15 –
Adjusting and Leveling the Projector
Take note of the following when setting up the projector:
•
The projector table or stand should be level and sturdy.
•
Position the projector so that it is perpendicular to the screen.
•
Remove the Back Foot Holder on the rear adjuster foot before adjusting the projection
angle.
•
Ensure the cables are in a safe location. You could trip over them.
1.
2.
3.
To raise the level of the projector, lift the projector [A] and press the height-
adjuster button [B].
The height adjuster drops down [C].
To lower the level of the projector, press the height-adjuster button and
push down on the top of the projector.
To adjust the angle of the picture, turn the tilt-adjuster [D] right or left
until the desired angle has been achieved.
Loading...