WIN600
Six room in-wall speaker-stereo interface
Installation instructions
Warning: To be installed and/or used in accordance with
appropriate local electrical codes and regulations.
Description: The Knöll
WIN600 six-channel
speaker-stereo interface can
safely power two to six rooms
of stereo speakers from one
stereo amplifier or receiver.
Speakers can be similar or
dissimilar and each will sound
their best. This stereo
interface can be used with and without stereo room volume
controls. Parallel or series speaker wiring is acceptable.
Maximum power input is 200 watts per channel. The WIN600
features an incredible "ultra" music quality frequency response
of DC to 500,000 Hz +/-0.1dB at all power levels up to 350
watts due to its transformer-free topology.
The SI1x6 is a "stackable with the components" version of
the WIN600.
Depending on the quantity and type of speakers chosen, the
WIN600 may offer the amplifier impedance as low as 4 ohms,
so we suggest that your amplifier (or receiver) be rated for
4-ohm (or lower) operation. The WIN600 is usually in-wall or
wall mounted away from the stereo components and does not
need a power supply.
Basic System Layout and Pre-Wiring: The WIN600 is wall
mounted in in-wall mount away from the stereo equipment. It
may get warm or a bit hot, so it needs ventilation for maximum
power and longest life. Don’t cover or block the vent holes.
Take care to mount it away from anything that can be damaged
by heat.
From each speaker run a fire rated two-conductor speaker
wire, ideally 16 gauge or larger for runs up to 33’ (10m) and 14
gauge or larger for longer runs to the WIN600 stereo
interface (or volume control then to the interface). To save
time and money, many installers run a four-conductor speaker
wire from the volume control to the stereo interface. If there
is more than one pair of speakers connected to a single
WIN600 room connection, wire the speakers in series or
parallel whichever makes the impedance closest to 4 or 8
ohms.
Do not attempt to make the final combined
speaker impedance less than 4 ohms.
If the WIN600 is not
fire rated four-conductor (or two two-conductor) 14-18-gauge
speaker wire from the stereo to the WIN600.
Connection to Stereo Equipment: Remove the WIN600 fourposition detachable speaker connectors. The stereo amplifier
or receiver outputs (left and right) are connected to the
WIN600 connector labeled “INPUT”. Be very careful to
observe the correct polarity. The WIN600 uses independent
floating grounds so bridged amplifiers can be used safely.
located next to the stereo, run a single
Connection to Speakers: Remove the remaining WIN600
four-position speaker connectors. Connect the speakers or
volume control inputs to any of the six connectors labeled
“ROOM” again strictly observing polarity. Check out or web
site www.knollsystems.com
for information on series and
parallel speaker wiring.
Note: For best sound quality always use Knoll 100%
transformer-free stereo volume controls such as the VC100,
VC100ss or VS100 in each room.
ROOM1 ROOM2 ROOM3 ROOM4 ROOM5 ROOM6
INPUT
Room 6 with
stereo volume
control
R>
Room 4
direct
+
connection
-
-
L>
Stereo Amplifier or
Stereo Receiver
"Speaker Outputs"
+
CAUTION:
MAY BE VERY HOT
(THIS IS NORMAL)
WIN600
Speakers
Operation: The Knöll WIN600 is completely automatic and
does not need any user adjustments after installation.
Specifications:
Peak RMS power rating: 300 watts per channel (5 seconds)
Continuous RMS power: 200 watts per channel
Frequency Response: DC to 500,000 Hz at all power levels
to 350 watts +/- 0.1dB
Speaker types: Most speaker types are acceptable.
Similar and dissimilar speakers can be
used on one interface and each will
sound their best.
Speaker wiring method: Series or parallel wiring is acceptable.
Speaker impedance: 4-16 ohms (single or multi-speakers)
Grounds Independent left/right grounds for
safe connection of all amplifier types
except tube or valve amps. See below.
Connection: Detachable screw terminals capable
of 12-22 awg wire
Dimensions: 10-7/8" w x 7-5/8" h x3" d
(27.6x19.4x7.6cm)
Color: White
Note: When using tube or valve amps, we suggest adding 150 ohm 3
watt resistors in parallel across each amplifier left and right output.
Warranty
Knöll Systems warrants its products sold in the USA and Canada by authorized Knöll
dealers to be free of defects in materials and workmanship. This warranty extends for two
full years from the date of purchase by the original consumer. Any products returned to
Knöll Systems and found to be defective by Knöll Systems within the warranty period
will be repaired or replaced at Knöll Systems option, at no charge. Knöll Systems will not
be responsible for the actual cost of installation or removal of the product, nor for any
incidental or consequential damages. Some states do not allow the exclusion or limitation
of incidental or consequential damages, so the above limitation may not apply to you.
This warranty gives you specific legal rights. You may have additional legal rights that
vary from state to state.
The WIN600 has no user replaceable parts.
Knoll Systems
145 Tyee Drive Point Roberts, WA 98281
11791 Machrina Way, #120 Richmond BC V7A 4V3
tel (604) 272 4555, fax (604) 272 5595
www.knollsystems.com
Made in Canada. WIN600 guide.doc 1999-2002 Knoll Systems. All Rights Reserved
Loading...