Knoll US-V3, US-P3, UR-P3, UR-V3, US3-HUB User Manual

Component Balun Specifications:

Models and Dimensions

UR-P3 (in-wall Decora™ version): 4.1"h x 1.4" w x 2.0"d.
UR-V3 (black enclosure): 1.1"h x 2.6"w x 2.8"d (28 x 66 x 71 mm).
US-P3 (in-wall Decora™ version): 4.1"h x 1.4"w x 2.0"d.
US-V3 (black enclosure): 1.1"h x 2.6"w x 2.8"d (28 x 66 x 71 mm).

US3-Hub (black stackable enclosure).

Video Bandwidth: 450 MHz +/- 3 dB.

Video Input: Receive unit: 0.5 V to 2V.

Video Output: Send unit: 0.5 V to 2 V.

Input and Outputs:

Send Unit: three RCA input jacks, one RJ-45 out-jack, one-DC
power input.
Receive Unit: three RCA output jacks, one RJ-45 out-jack.
US3-Hub: Three RCA input jacks, six RJ-45 output jacks, one DC
power input, one input and one output link RJ45 jack.

Power
Send Unit: 12 VDC (one PS1202 power supply will power one
send and one receive and is connected to the send unit only.)
Receive Unit: 12 VDC (from send or hub).
US3-Hub: 15 VDC (one PS1506, included, will power the hub
and up to six receives).

Warranty

Knoll Systems warrants its products sold in the USA and Canada by authorized
Knoll dealers to be free of defects in materials and workmanship. This warranty
extends for three full years from the date of purchase by the original consumer.
Any products returned to Knoll Systems and found to be defective by Knoll
Systems within the warranty period will be repaired or replaced at Knoll Systems
option, at no charge. Knoll Systems will not be responsible for the actual cost of
installation or removal of the product, nor for any incidental or consequential
damages. Some states do not allow the exclusion or limitation of incidental or
consequential damages, so the above limitation may not apply to you. This
warranty gives you specific legal rights. You may have additional legal rights
that vary from state to state.

Knoll Systems www.knollsystems.com

145 Tyee Drive Point Roberts, WA 98281
12140 Horseshoe Way, Richmond BC V7A 4V4
tel [phone], fax [phone]

Made in Canada Knoll Systems All Rights Reserved

UR-P3 Component Video Receiver
UR-V3 Component Video Receiver
US-P3 Component Video Sender
US-V3 Component Video Sender

Installation Instructions v1.1

Warning: To be installed and/or used in accordance with

appropriate electrical codes and regulations. If you are not sure
about any part of these instructions, consult a qualified
electrician.

Caution: Do not install this product in an electrical junction box
with 110V or higher unless an approved barrier separates the
high and low voltage sections.

Introduction: Thank you for your purchase of a Knoll active
balun system. This system is specifically designed to send a
three wire Pb, Pr, Y component or RGB signal safely down a cat
5 or cat 5e wire up to 500 feet without encountering image
problems. Balun is an acronym for:

BALance – UNbalance

The send module takes a conventional component signal and
balances it (signal is not tied to a ground reference) then sends
it via cat 5 to the receive module (with power from the send
module). The receive module unbalances the component signal
back to its former state. This process does not allow any stray
magnetism of any sort to contaminate the signal while it is
being transported.

Features:

• Tabletop box design or Decora™ style available.

• Will safely send 480i/p, 720p and 1080i/p signals.

• PS1202 power supply required on send side only.

• 6 output hub available

• Mix and match decora style and tabletop style.

Wiring: A send
module (US-P3 or
US-V3) needs to be
connected to a Knoll
receive module (UR­P3 or UR-V3) to work
correctly. The send
and receive module
are connected using
a single cat 5 wire using all 8 conductors. Connection is made with the
RJ45 connector (RJ45 plug not supplied). Always use standard cat 5
wiring practices. Using the correct wire pairs and polarity is VERY
important.

Connection to stereo video source equipment: Connect the three
US-P3 or US-V3 gold RCA jacks with a good quality gold connector
triple wire component RCA jumper cable to the appropriate three
component output jacks on your DVD, dish receiver, D-VHS, VCR,
stereo or other equipment.
If there is a switched outlet on your output equipment, you may want
to plug the PS1202 power supply to the switched outlet.

Make sure a good quality RJ45 8-8 crimper is used to
connect the RJ45 connector to the cat 5 wire. Poor crimping
and mismatched wires are the biggest cause of installation
problems.

Power requirements: The Knoll balun system requires a single
PS1202 power supply connected to the send unit only. In certain cases
with very long leads a higher voltage PS1506 15 VDC power supply
may be required if wavy or image video lines are evident.

DVD Player

PS1202

CAT 5

US-P3

Power supply
gives power
for UR-V3

Connection to the Projector, TV or other components: Connect
the three US-P3 or US-V3 gold RCA jacks with a good quality gold
connector triple wire component RCA jumper cable to the appropriate
three component input jacks on your projector, plasma, TV or other
component. Make sure the correct projector, plasma, TV or other
component input is selected.

Multiple Connection(s): If the component signal needs to be sent to
more than one receiver, this can easily be accomplished by daisy
chaining the Knoll component senders. The US-P3 and/or US-V3 sender
RCA inputs need to have their three RCA inputs Y-corded together.
Each sender is connected via one cat 5 wire to one UR-P3 or UR-V3
receiver (as above). Three resistors in all but one of the senders need
to be snipped. For example, if four senders are being Y-corded
together, three (not all four) of the US-P3 and/or US-V3 senders need
to be opened up and have the three 75 ohm through hole resistors
beside the RCA jacks snipped off. Receive units do not have any
alterations. Each send unit requires a PS1202 power supply.

To loop from a local source going to a local component (such as a TV)
using Y-cords, the three 75 ohm resistors in the send unit MAY need to
be snipped.

The Knoll send receive system does not have any user adjustments and
is completely automatic. If need be, please call our tech line for details
at 1 800 566 5579.

This product may contain lead that some states have determined are
harmful. Wash you hands after touching this product.

Decora™ is a trademark of Leviton

DLP-TV

UR-V3

Power is supplied
by US-V3