Stereo Power Amplifier
Version 1.1
INSTALLATION
AND OPERATION
MANUAL
MA205
2
Congratulations and thank you for choosing the Knöll
MA205 power amplifier. The MA205 is designed to meet
the amplifier needs where high quality sound is a specific
requirement.
Key Features:
1. Manual and Automatic Power On and Off.
The MA205 stereo power amplifier is designed to be
turned on when a video signal is detected, music inputs are
sensed, a 12 volt trigger is activated or the front panel
power switch is pushed on. Power off is automatic in all
modes except the front panel power button.
2. Whole house music override. In homes, yachts,
businesses and motorhome applications (typically with
plasma or large screen TV's) the MA205 features
amplifier inputs so that whole house music system can be
heard on the local speakers (without the MA205 turned
on). When the local source (TV, dish, etc.) needs amp
power, the whole house music is automatically switched off,
the MA205 amplifier turns on and plays the local source.
3. Automatic protection circuitry . Each MA205
channel is individually and fully protected against low
impedance, overheating, overloading, overvoltage and
undervoltage. The protection circuitry automatically
restores the amplifier channel as soon as its parameter
returns to the safe operating area.
4. Individual input gain adjustment. Each channel
features an input gain adjustment pot to adjust each
channel for gain and speaker sensitivity variations. The
gain adjustments are on the rear of the MA205 so
installers normally set the gain.
5. Stackable 17" chassis. Two MA205's can fit side
by side and stacked for applications requiring more than
two amplifier channels.
Installation
Installing the MA205 should be relatively easy. With a bit of
planning, the MA205 will give trouble free service for years.
1. The most important consideration when installing the MA205
is cooling. When installing it in an equipment stack, it should be the
top component. It needs at least 3"-5" of space above the amplifier
to allow for adequate convection cooling.
2. When installing the MA205 in a rack we suggest adding a
3-1/2" blank above and below the MA205. In multiple MA205
installations, plan for a 3-1/2" blank (double) between each MA205
and a 3-1/2" blank on the top and bottom. Amplifiers should always
be the top components in a rack system.
3. If MA205 channels frequently shut down due to overheating,
install a fan directed up from the MA205 bottom center.
4. Never operate the MA205 on its side, as the cooling potential
drops significantly when operated on the side.
5. Connect the MA205 inputs to the source component outputs with
good quality, short as possible RCA jack cables.
6. Connect the MA205 speaker outputs to speakers using good
quality speaker wire. Minimum 16 gauge copper wire is recommended
with 14 gauge minimum for runs over 30' (10m).
Note: Ideally the MA205 is operated into 4-8 ohm speaker
loads. The MA205 will not operate into 2 ohm loads.
Do not attempt to mono bridge the MA205
7. Make sure the speakers in each room are connected in phase with
the amplifier + going to the speaker + . Out of phase speakers give
unstable imaging and poor bass response.
8. If connecting the MA205 to the whole house sound system,
connect the whole house amplifier outputs to the MA205 speaker
terminals labeled "AMP INPUTS" using good quality speaker wire.
9. If you are planning to use a video signal to trigger the MA205
power on and off, connect a good quality video wire with an RCA
jack to the MA205 input labeled "Video Input". Make sure the music
sense button is in the "OUT" position.
10. If the music sense or video input is being used to turn the
MA205 power on and off, switch the music sense button to the
"OUT" position. Adjust the "Sens" itivity pot on the MA205 so the
amp turns on when quieter passages are playing via the RCA line level
inputs. Adjust the "Delay" pot so the amp turns off a reasonable time
after the music has stopped.
3
installation continued...
11. To use the 12VDC trigger to turn the MA205 on/off, connect the
trigger to the 3.5mm trigger jack. Set the music sense switch to "IN".
The front panel power switch is normally off (out position).
12. Individually adjust the channel gains as required. For best noise
and hum cancellation, all MR205 gains should be on full (fully cw).
MA205 2 Channel Power Amplifier
Inputs: Gold RCA style with adjustable gain
Input impedance: 20 k ohms
Outputs: Gold 5 way Binding posts
Output power: 50 watts RMS per channel (8 ohms)
Peak output power: 70 watts RMS per channel (4 ohms)
Ideal impedance: 4-8 ohm speakers
Freq. response: 10 Hz - 40 kHz +/- 1 dB (1w)
S/N ratio: over 95 dB A weighted 50 watts
THD distortion: <0.1% 20 Hz to 20 kHz
IMD distortion <0.01% 60 Hz 7 kHz 4:1 (SMPTE)
Trigger control: 12 VDC 35mA (3.5mm input jack)
Power: 140 watts 117 VAC
Dimensions: 8.5" x 3.5" x 10.5"
Weight: 8 lbs (3.6 kg)
Caution: Never listen to sound that is distorted. If
distorted sound is heard, turn the volume down immediately
or speaker and/or amplifier damage could occur that is
not covered by the warranty. If this problem persists,
contact your dealer.
User Adjustments and Service: There are no user
adjustments on the MA205. Your installer may make
certain level and delay adjustments on the rear panel.
Caution: The MA205 contains no user serviceable parts,
so do not attempt to open or repair the MA205. Refer
servicing to a qualified technician only or contact the
factory for information.
4
5
Troubleshooting
If a problem is encountered with the MA205, the most expedient
procedure is to locate the problem and if possible repair it before
requesting service. Be sure to carefully check other system components
such as controllers, CD players, volume controls, wiring, speakers, etc.
that may be at fault.
Problem Action
Power indicator does 1. Check that the MA205 is plugged in.
not light - no sound 2. Test the AC outlet with a lamp.
3. Confirm the MA205 front power button is on
Sound cuts out 1. Verify speaker impedance is 4-16 ohms.
Changing speakers may be required.
2. Check if the MA205 feels hot. If it's
hot, increase cooling - see Installation.
3. If music sense is selected on the rear, the
music may level may be too low to activate
and hold the amp on. Turn the source volume
up and the MA205 gain controls down to
compensate. Connect a 12 VDC trigger
(trigger mode) or contact the Knöll factory
for information on defeating the music
sense mode.
4. In music or video sense mode, the MA205
rear delay time may have to be increased.
Sound is distorted 1. Turn the volume down
2. Check speakers for damage.
3. Check inputs for proper levels. MA205
gain and the music source output levels
may have to be adjusted.
4. Speakers may have less than 4 ohm rating
and may need to be changed.
MA205 does not 1. In trigger mode, make sure trigger power is
automatically turn off turning off by removing trigger plug on rear.
Make sure front panel power switch is OUT.
2. In music sense mode turn off source music
components. If the MA205 doesn't turn off
after about 2 minutes remove RCA input
plugs. If the MA205 turns off, reconnect
the RCA plugs and try adjusting the
sensitivity down.
In Canada:
11791 Machrina Way #120
Richmond, B.C. V7A 4V3
Knöll Systems
tel (604) 272-4555
fax (604) 272-5595
Knöll Systems, Richmond, BC & Point Roberts WA
C
COPYRIGHT 1998-2003, Knöll Systems, All Rights Reserved
In America:
145 Tyee Drive
Point Roberts, WA 98281
Limited Warranty
Knöll Systems warrants MA205 amplifiers sold in the USA or Canada
by authorized Knöll dealers to be free from defects in materials and
workmanship. This warranty extends for three full years from the date
of purchase by the consumer. Any products returned freight prepaid to
Knöll Systems and found to be defective by Knöll Systems within the
warranty period will be repaired or replaced at Knöll Systems option,
at no charge. Knöll Systems will not be responsible for the actual cost
of installation or removal of the product, nor for any consequential or
incidental damages. Some states do not allow the exclusion or
limitation of incidental or consequential damages, so the above
limitation or exclusion may not apply to you. This warranty gives you
specific legal rights. You may have additional rights which vary from
state to state. Knöll products sold outside of the USA and Canada may
be covered by warranties provided by an authorized Knöll distributor.
Please contact the distributor in the country that the Knöll product was
purchased.
* DMS, Powermatch, Transformer free and Digicom
are trademarks of Knöll Systems
Printed in Canada
12VDC
Trigger
234
5
234
5
234
5
234
5
AC120V
140 watts
L
R
L GAIN R
IN OUT
Note 1: Ideal speaker impedance is 4-8 ohms.
MA205 REAR PANEL
4-16 ohms
AMP INPUTS
TO SPEAKERS
L
R
+
+
-
-
Sens
Delay
Video
Input
Music sense
Out=Active
Connect a video output
such as VCR or plasma
TV to here if the amp is
to be triggered on when
a video signal is
present. Make sure the
music sense button is in
the out position. For
video sensing without
music sensing turn the
"Sens" pot fully
counterclockwise.
Connect stereo line
level inputs here
Connect these unbuffered
stereo line outs to other
amplifier inputs as needed
Connect the "Amp Inputs" speaker
level inputs to the whole house
audio system or other amplifier
output. The signal here passes
directly to the speakers when the
MA205 amp isn't triggered or
turned on
Connect the "To Speakers" terminals
to the 4-8 ohm speakers
Connect this 3.5mm
trigger jack if the
amp is to be triggerd
on when a 12 VDC
signal is present.
Polarity can be
reversed.
The music sense (auto turn
on when music is present)
button should be OUT
(active) when the MA205
power is to be triggered
either from music sense
from the video signal.
The music sense button
should be IN when the amp
is turned on and off with
either the front panel
power switch or the 12
VDC trigger.
Adjust the gain
when the system is
on. Best signal to
noise ratio is when
amp gains are on
full (clockwise).
When using music sense
only, adjust Sens so the
amp turns on when source
music is at a medium low
volume. Sens is not used
for video on or trigger on.
For video sensing without
music sensing turn the pot
fully counterclockwise.
After amp is on, delay is
used to turn off amp
after source music ends.
Ideal delay adjustment is
about 20-40 seconds. This
feature is used with video
on or music sense only.
Loading...