Knoll HDP6000 User Manual

Kameleon
HDP6000

1080p DLP™ Projector

Users‟ Manual v1.1

2

FCC Warning

Note: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:

 Reorient or relocate the receiving antenna.
 Increase the separation between the equipment and receiver.
 Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

 Consult the dealer or an experienced radio/TV technician for help.

Canada

This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

Safety Certifications. REGULATORY MODEL H8300.

UL, cUL, TUV, GOST
Other specific Country Approvals may apply. Please see product certification label.

This product is RoHS compliant.

Declaration of Conformity

Knoll Systems, 12140 Horseshoe Way, Richmond, BC V7A 4V5, Canada
We declare under our sole responsibility that this projector conforms to the following directives and norms:

EMC Directive 2004/108/EC
EuP Directive 2005/32/EC
EMC: EN 55022
EN 55024
EN 61000-3-2
EN 61000-3-3
Low Voltage Directive 2006/95/EC
Safety: IEC 60950-1:2005, MOD

February 2010.

Trademarks

Apple, Macintosh, and PowerBook are trademarks or registered trademarks of Apple Computer, Inc. IBM is
a trademark or registered trademark of International Business Machines, Inc. Microsoft, PowerPoint, and
Windows are trademarks or registered trademarks of Microsoft Corporation. Adobe and Acrobat are
trademarks or registered trademarks of Adobe Systems Incorporated. DLP® and the DLP logo are
registered trademarks of Texas Instruments and BrilliantColor™ are a trademark of Texas Instruments. Knoll
is a trademark of Pacific Sound & Signal Inc.

WARNING: This product has a lamp, which contains a very small amount of mercury. Dispose of it as
required by local, state, or federal ordinances and regulations. For more information, see www.eiae.org.

Knoll Systems
12140 Horseshoe Way, Richmond, BC V7A 4V5 Canada
145 Tyee Drive, Point Roberts, WA 98281 USA

www.knollsystems.com

3

TABLE OF CONTENTS

Safety Warnings 4
Introduction 5
Positioning the projector 8
Choosing the aspect ratio 9

Video connectors 10
Connecting a video device 10
Composite (RCA) video connection 10
S-video connection 10
Component (RCA) connection 10
SCART RGB connection 10

Digital connections 10
DVI connection 10
HDMI connection 10

Computer connections 11
RS-232 connections 11

Displaying an image 11
Adjusting the image 11
Shutting down the projector 12

Troubleshooting your setup 13
Using the remote control 17

Using the keypad buttons 18
Optimizing video images 19
Customizing the projector 19

Using the menus 19
Picture menu 20
Settings menu 22

Maintenance 24
Cleaning the lens 24
Replacing the projection lamp 25

RS-232 terminal specs 26

Warranty Information 32

4

Important Operating Considerations for Safety

Refer to this guide for proper startup and shutdown procedures.

• Follow all warnings and cautions in this manual and on the projector.

• Place the projector in a horizontal position no greater than 8 degrees off axis.

• Locate the projector at least 4' (1.2m) away from any heating or cooling vents.

• Do not block ventilation openings. Locate the projector in a well ventilated area without obstructions to

intake or exhaust vents. Do not place the projector on a tablecloth or other soft covering that may block
the vents.

• Do not place the projector in direct sunlight, humid, greasy or dusty places or in places where the projector
may come into contact with smoke or steam.

• Do not touch the exhaust vents. This area will become hot while the projector is being used. Be sure
children are kept away from this area.

• Do not look directly into the lens while the projector is being used. Be especially careful that children do not
stare directly into the lens.

• Do not push objects of any kind into this projector through its venting as object may touch dangerous
voltage that could result in a fire or electrical shock.

• Do not drop the projector.

• Do not spill liquid on the projector. Spilled liquid may damage the projector.

• Do not place any object on the projector.

• Do not stand or step on the projector.

• Use the power cord provided. Connect the power cord to a receptacle with a protective safety (earth)

ground terminal. The AC power cord has a three-pin grounding-type power plug. This plug will only fit a
grounding-type power outlet. This is a safety feature. Do not remove the grounding pin on the power plug.
A surge-protected power strip is recommended. Do not overload wall outlets.

• When disconnecting the power cord, hold the plug, not the cord. Unplug the projector from the wall outlet, if
the projector is unused for an extended time.

• Wash hands after handling the cables supplied with this product.

• The projector remote control uses batteries. Make sure the batteries polarity (+/-) is aligned correctly.

Dispose of used batteries in accordance with local disposal laws.

• Use a Knoll approved ceiling mount kit for proper fitting, ventilation and installation. The projector warranty
does not cover any damage caused by use of non-approved ceiling mount kits or by installing in an improper
location.

• When the projector is ceiling mounted, wear protective eyewear to prevent eye injury before opening lamp
door.

• The projector must be installed by a qualified professional in order to ensure proper operation and reduce
the risk of hazards or injury. It is not recommended you install the projector yourself.

• Refer all service to qualified service personnel. Servicing your own projector can be dangerous to you and
will void the warranty.

• Only use replacement parts specified by Knoll. Unauthorized substitutions may result in fire, electrical
shock, or injury, and may void the warranty

• Only genuine Knoll lamps are tested for use in this projector. Use of non Knoll lamps may cause electrical
shock and fire, and may void the projector warranty.

• Hg – Lamp contains mercury. Manage in accordance with local disposal laws. See www.lamprecycle.org.

• The projector uses a high-pressure mercury glass lamp. The lamp may fail prematurely, or it may rupture

with a popping sound if jolted, scratched, or handled while hot. The risk of lamp failure or rupture also
increases as the lamp age increases; please replace the lamp when you see the “Replace Lamp” message.

In the unlikely event of a lamp rupture, particles may exit through the projector vents. Keep people, food,
and drinks out of the "keep out" area under and around the projector, as indicated by the "X" areas below.

5

Unplug this projector from the wall outlet and refer servicing to qualified service personnel under the
following conditions:

• When the power cord or plug is damaged or frayed

• If liquid has been spilled into the projector

• If the projector has been exposed to rain or water

• If the projector does not operate normally by following the operating instructions. Adjust only those controls

that are covered by the operating instructions as improper adjustment of other controls may result in
damage and may required extensive work to restore the projector to normal operation

• If the projector has been dropped

• When the projector exhibits a distinct change in performance, this indicates a need for service.

Follow these instructions to help ensure image quality and lamp life over the life of the projector. Failure to
follow these instructions may affect the warranty.

Introduction

Congratulations and thank you for your choice of a superior digital image projection device. Your
new Knoll projector is specifically designed for home cinema applications. The projector sets a

high standard using the latest DLP™ technology and new DNX video processing from

Pixelworks™. This projector has 1920 x 1080 resolution (1080p). Whether you are watching

movies or High Definition broadcasts or playing the latest video game, you will enjoy amazing
image quality. The unique design and color of the projector make it a welcome addition to your
home.

keypad

Top cover

Lens Lamp Access

Receiver (IR)

Product specifications

To read the latest specifications, be sure to visit our website at www.knollsystems.com as
specifications are subject to change.

Optional accessories can be found on our website at www.knollsystems.com or at your retailer or
dealer.

6

Power RS232
S-Video HDMI
VGA

Rear Connector Panel

USB
12 VDC triggers

Composite video Component video Wired remote

The projector provides the following connection options:

• VGA computer.

• Two HDMI™ (High Definition Multimedia Interface)

• Three Component Video (RCA)

• S-video

• Composite video (RCA)

• USB port

The projector also provides the following connectors:

• RS-232 for serial control

• 12-volt DC output (see below)

Three 12-volt DC outputs

The 3.5mm mini-jack trigger provides a 12-volt, 0.25 amp DC output. It provides a constant output
while the projector is on. It has numerous uses. For example, if you connect your projection
screen to the 12-volt DC output with the cable that came with your screen, when you turn on the
projector the screen will move down; when you turn the projector off, the screen will return to the
storage position.

12V+
ground

3.5mm plug 12VDC output

screen relay (see screen
manufacturer for details)

The “Lamp” trigger turns on when the lamp is lighted. If you connect your projection screen to this
output using the cable that came with your screen, the screen will move down when the lamp is
turned on and the screen will return to its storage position, when the lamp is turned off.

The Letterbox “1” and “2” triggers are active when the projector is placed in letterbox mode and
are utilized for variable masking and anamorphic lens control. (These triggers are off when
SplitScreen is active.)

7

Setting up the Projector

There are a number of factors to consider when determining where to set up the projector,
including the size and shape of your screen, the location of your power outlets, and the distance
between the projector and the rest of your equipment. But here are some general guidelines.

NOTE: To ensure adequate cable access, do not place the
projector within 6 inches (0.15 m) of a wall or other object.

Position the projector on a flat surface (either on a table or ceiling mounted) at a right angle to the

screen at least 1.5m (4.9‟) from the projection screen.

The projector should be within 10 feet (3 m) of your power source and within 6 feet (1.8 m) of
your video source(s), unless good quality extension cables or baluns are to be used.

When installing the projector on the ceiling, refer to the installation guide that comes with the
Ceiling Mount Kit for more information. Knoll recommends use of the CM33 mount shipped with
the projector or the deluxe swivel ceiling mount. The addition of a CM20+6 extension bar lowers

the projector 6” per bar as required. The CM25EX is an adjustable extender that can lower the
projector 6.75” to 11” (17-28 cm). The ceiling mount kit may be sold separately.

Position the projector the desired distance from the screen. The distance from the lens of the
projector to the screen, the zoom setting, and the video format determine the size of the projected
image.

If the image is square but not centered on the screen or viewing area, adjust it by using the lens
shift dials. Use the Horizontal dial to shift the lens left or right. Use the Vertical dial to shift the lens
up or down.

NOTE: As the lens is shifted away from the lens centerline, the horizontal shift range is
reduced. To adjust lens shift efficiently we suggest you follow these steps:

1 Use vertical lens shift to move the image closer to the lens centerline than the final vertical

position.

2 Use horizontal lens shift to determine the center horizontal position, then move image to

the center horizontal position. Maximum horizontal offset +/-15%.

3 Use vertical lens shift to move the image away from the lens

centerline to the final vertical position.

4 Use horizontal lens shift to move the image to the final horizontal

position.

5 If lens shift is unable to move the image far enough, move the
projector (preferable) or tilt the projector and then use vertical and
horizontal keystone to re-position the image.

• The vertical image offset range is 105%~130% for the HDP6000
(default for is 105%). The default horizontal image offset is +/-15%,
however at maximum vertical image offset, there is no horizontal
lens shift.

8

Screen Diagonal

92"

103"

106"

110"

122.5"

146.75"

Minimum Distance

121"

135"

139"

145"

161"

193"

Maximum Distance

183"

204"

209"

217"

242"

290"

Viewing Area

45"x80"

50.5"x89.75"

52"x92"

54"x96"

60"x107"

72"x128"

Projector Positioning

The projected image becomes larger as the distance between the unit and screen increases.
The manual zoom allows the distance from the screen to be within a minimum and maximum

range. See the chart on the next page for details. The example below defines the screen height,
width, diagonal, etc.

HDP6000 Projection Throw Distance 16:9 Video Screen:

MAXIMUM DISTANCE TO SCREEN (16:9) = 1.98 x SCREEN DIAGONAL SIZE
MINIMUM DISTANCE TO SCREEN (16:9) = 1.31 x SCREEN DIAGONAL SIZE

An interactive screen calculator (in Microsoft Excel format) is available at:

www.knollsystems.com/prod-hdp6000-throw.html
Anamorphic Lens

Please note the HDP6000 is designed for use with 16:9 screens. They also have a
built in scaler for use with 2.35:1 screens. To display images at the highest
definition possible in 2.35:1 or cinemascope (most major movies are filmed in

2.35:1) an anamorphic lens is required. We recommend the Panamorph brand,
which has fixed, movable and motorized anamorphic lens for use with the
HDP6000.

9

Choosing the aspect ratio

Aspect ratio is the ratio of the image width to
image height. HDTV and most DVDs are 16:9,
which is the default for this projector. When in
4:3 mode the projector places black bars on
both sides of the image. Native mode centers
the image and turns off the internal scaler so
that any resolution larger than the native
projector resolution is cropped on the edges.
Letterbox expands the image to fill the screen.

What you plan to project will also help you
choose between 4:3 and 16:9. For example,
most low definition TV shows are 4:3, while
most movies are 16:9. If you have a 16:9
screen, then you should select an aspect ratio
of 16:9 for anamorphic movies and HDTV, and
Native for 4:3 content. If you have a 4:3 screen
you should still use 16:9 for anamorphic movies
or HDTV, but you also have the option of using
4:3, Native, or Natural Wide for 4:3 content.
Keep in mind that anamorphic movies only
appear correctly if the DVD player is set to
output to a 16:9 television. Natural Wide
stretches a 4:3 image to fill the entire 16:9
screen. The center two-thirds of the image is
unchanged; the edges of the image are
stretched.

Cable Management
The HDP6000 features an integrated
cable management system that allows
you to keep the cables organized. To
use the cable management system,
thread the cables into the slots as
shown in the illustration.

Video Quality

The first step for connecting video is determining what type of output connectors your source
video device has. If there is more than one output, select the one with the highest quality. The
best quality ranking, with 1 being the highest, is:

1. HDMI.

2. Component (RCAs)

3. S-video

4. Composite Video (RCA)

If your device has a VGA connector, you can use the VGA connector for a high-quality image.
Many PC game systems have VGA connectors.

10

Connecting a video device

You can connect video devices such as VCRs, DVD players, camcorders, digital cameras, video
game consoles, HDTV receivers, and TV tuners to the projector. Connect the audio from your
video device to your stereo system to get sound. You can connect the projector to most video
devices that can output video.

You cannot directly connect the coaxial cable that enters your house from a cable or
satellite company; the signal must pass through a tuner first. Examples of tuners are digital
cable boxes, VCRs, digital video recorders, and satellite TV boxes. Basically, any device that can
change channels is considered a tuner.

An HDMI cable is provided with your projector so you can quickly and easily connect a video
source to the projector and see the amazing image that is displayed. Once you have determined
a more permanent location for your projector, we recommend purchasing higher quality cables in
the proper length to get the best image from your particular video equipment.

Composite (RCA) video connection

Plug the composite video cable‟s yellow connector into the video-out connector on the video
device. Plug the other yellow connector into the yellow Composite connector on the projector.

S-video connection

If your video device uses a round, four-prong S-video connector, plug the S-video cable into the
S-video connector on your video device and into the S-video connector on the projector.

Component (RCA) connection

If your device uses component connectors, plug a component video cable with red, green, and
blue RCA connectors into the source device‟s component connectors and the Component
connectors on the projector. The HDP6000 has three component video inputs. Be sure to use
the remote control to select the correct component input.

Digital connections

The two HDMI (High-Definition Multimedia Interface) connectors are digital and yield the highest
quality image. It is common for these signals to be encrypted with HDCP (high-band width digital­content protection). Your new projector ships standard with decryption codes so you can enjoy
these high quality, all digital images.

HDMI connection

HDMI is a standard, uncompressed, all-digital audio/video interface. HDMI provides an interface
between sources, such as set-top boxes, DVD players, and receivers and your projector. Plug an
HDMI cable into the video-out connector on the video device and into the HDMI connector on
the projector. To display HDMI with its deep color and 30-bit detail, a HDMI source is needed.
Please note the HDP6000 has no audio capabilities at all. The HDP6000 has two HDMI video
inputs. Be sure to use the remote control to select the correct HDMI input.

Please note that the projector has no audio capabilities, so audio signals transferred through
HDMI will not be audible.